ADDN/ ALTN OF BLDG NO P 353 (CONTROL ROOM OF 21 CORPS PRO UNIT) AND ADDN/ ALTN OF BLDG NO P 380 (MT SERVICING GARAGE) OF 12 TAC, AF, DRONACHAL TOP UNDER GE DRONACHAL

Amount

Cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings. converting window into door openings, etc. and finishing the jamb and door cill as existing surface with Cement mortar

Making good under cills, jambs or over arches, lintels and bressummers. including all pinning where necessary in cement mortar 1:4 complete

Taking down steel chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but n exc 4 sqm each complete all as specified and directed.

Surface dressing in hard dense soil n exc 15 cm deep

Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.soft/ disintegrated rock including returning filling complete all as specified and directed

M&L for Reinforced cement concrete Reinforced cement concrete (nominal mix) Type B0 1:2:4 (12.5mm graded aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M&L Reinforced cement concrete Type B0 1:2:4 (12.5mm graded aggregate) in Columns , pillars ,Piers ,Posts and struts complete all as specified and directed

M&L for Reinforced cement concrete Type B0 1:2:4 (12.5mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

M&L for Reinforced cement concrete Type B0 1:2:4 (12.5mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

M&L for formwork to sides of concrete curved foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter surface flat with fair finished surfaces

M & L Formwork to sides of pillars, posts, struts, piers, columns and stanchions square or rectangular in plan to provide rough finish surface to concrete

M & L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.with rough finished surface

M & L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L CRS reinforcement bars 10mm and over using cut to length bent to shape as required including cranking bending spirally for hooking ends and binding with and including mild steel wire (annealed not less than 0.9mm dia or securig with clips etc complete.

All as per item No 14.00 above but 6 to 8mm dia in stirrups, spacers and binders all as specified and directed.

Demolition of brick or stone masnary work built in cement mortar incl all quions, arches, pillars etc. but excluding ashlar facings dressed stone work and precast concrete articles and removing outside MD land complete all as specified and directed.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for all as directed by Engineer-in-Charge.

M&L brick work with sub class ‘B’ modular bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 all as specified and directed.

M&L brick work with sub class ‘B’ modular bricks straight or curved on plan exc 6m mean radius half brick thick wall built in cement mortar 1:4 all as specified and directed.

Taking down cement plaster from brick or concrete surface incl raking out joints hacking for key and scrubbing down with water complete all as specified and directed.

M&L for rendering 10 mm thick on brick or concrete surfaces or surface other than fair faces of brick work in cement plaster 1:6, finished even and smooth w/o using extra cement all as specified and directed

M&L for preparing of newly plastered surface of walls and applying one layer of white putty and two coats of oil bound distemper over a coat of compatible primer etc complete all as specified and directed.

M&L for rendering 15 mm thick in two layers over brick work or concrete surfaces, 10mm thick in cement plaster 1:4 backing coat and 5mm thick in cement plaster 1: 4 mixed with WPC all as specified and directed. Note: WPC shall be measured and paid separately under relevant item.

Supply only integral water proofing compound of approved make complete all as specified and as directed

M&L for preparation of newly plastered or unplastered surfaces in walls soffits, facia, chajjas and applying two coat of exterior weather proof water based emulsion over a coat of compatible primer complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) , removing serviceable tiles to store and rubish of the premisses complete all as specified and directed

M&L for 25mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate, including finishing of concrete topping even and rough complete all as specified and directed

M&L for coloured Non-skid Ceramic tiles 7 to 8 mm thick (square/ rectangular), coloured tiles, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed in CM 1:6 all as specified and directed.

M&L for coloured Glazed ceramic tiles in vertical surface 450 X 300 X 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to matchtiles in vertical surface including 10mm thick rendering in CM 1:4, all as specified and directed

S&F vitreous china wash down water closet pan (pedestal pattern), white and trap including seat cover, fixing bolt, flush pipe, connection to drain (or out going pipe) and to flushing pipe, antisyphonage pipe, etc complete all as specified & as directed.

S&F of Vitreous China Urinal Half Stall type, white with union for discharge pipe including waste pipe and urinal spreader, Bottle trap of PTMT having minimum water seal of 25mm .(Minimum weight 32mm-260gms/ 40mm-270 gms) fixing with 15mm dia pipe complete all as specified and directed

S&F of vitreous China wash basin, white, flat back, size 450x300mm including PVC connections 15mm size with PTMT nuts of length 450mm, 40mm pvc waste pipe of suitable length, brackets,and cutting for and pinning in ends of brackets or erecting stand including waste coupling complete all as specified and as directed by the Engineer-in-Charge.

S&F of 10 ltrs capacity PVC Valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets flushing cistern, PVC flushing pipe of suitable length and PVC connection 450mm long. complete all as specified and as directed by the Engineer-in-Charge

S&F 15mm bore dia Chromium plated stop valve/angle cock, but fancy type, chromium plated with long shank and cup (concealed type) and fixed complete all as specified and directed

S&F 15mm bore, fancy type long body bib tap of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by the Engineer-in-Charge.

S&F two way bib tap 15mm dia all as specified and directed.

S&F 15 mm long neck pillar taps, cast copper alloy, chromium plated with capstan heads, chromium plated, screwed down high pressure, with or without letter hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixing complete all as specified and directed by engr in charge.

S & F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge

S&F Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed.

S&F PVC connection 15mm dia of length not less than 600mm with both ends, brass fly nut for water supply complete all as specified & as directed.

S&F brass chromium plated shower rose with swivel joint not less than 125mm dia and not less than 200mm long arm all as specified and directed.

S&F Health faucet( ABS Body) mild steel CP suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook incl making connections and fixd in position complete in all respect as specified (Make: prayag)

S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms)

S&F CPVC pipe 20mm dia of grade SDR-11 (class-I) including all CPVC and brass fittings fixed to wall, floor or ceiling or laid in floors etc complete all as specified and directed.

Cutting channels, grooves or rebates n exc 15cm girth, and trimming surface all as directed by Engr-in-charge

S&F CPVC pipe 25mm dia of grade SDR-11 (class-I) including all CPVC and brass fittings fixed to wall, floor or ceiling or laid in floors with and incl clamps etc complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank 500 ltrs cap cyllinderical vertical with closed top hoisted and fixed in position at roof or stand all as specified in SSR Pt-I complete all as specified and directed

S&F 25mm Ball (float) valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron/pvc/cpvc pipe in water tank and fixed. (Minimum weight 25mm-455gms) complete all as specified and directed

S&F of 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement

S&F in repair 110mm dia PVC (SWR) pipe and single socketed in any length with rubber ring joint laid in trenches, floors or fixed to walls.

S&F 75mm dia PVC (SWR) pipe and single socketed in any length with rubber ring joint laid in trenches or in floor or fixed to walls.

S&F 75 mm bore PVC (SWR) junction (single ‘T’) equal or unequal.

S&F 75 mm bore PVC (SWR) bend in any radius.

S&F solid PVC door frame(approved color) of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, fixing in opening as per specification and drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter(approved color and pattern) 30mm thick (stiles) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap inserted for top rail and bottom rail. Penelling of plain colour PVC sheet to be fitted to the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site all as specified and directed.

S & F 100mm size Butt hinges, medium weight cold rolled, stainless steel and fixed complete all as specified and as directed.

S&F Aluminum tower bolts of extruded section of size 150mm all as specified and directed.

S&F 150 mm size Extruded aluminium alloy handles, fabricated type., anodised handles all as specified and directed.

S&F 200mm long aluminium alloy anodised sliding door bolts with hasp and staple (bolt type) & fixing clip of sheet cast or extruded section & fixing bolt & sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) frame and shutters with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, suitable aluminum handle, handle lock/ mortice lock for door shutter etc all complete as per architectural drawings complete all as specified and directed.

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including neccesary cutting and holes for glass/ aluminum doors all as specified and directed

Supply & fixing of framed work such as grills, gratings, cooler stands etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 incl necessary fixing to walls as directed.

S&F mild steel Mortice lock 4 lever, vertical type, size 100 mm complete all as specified and directed

S&F 4.8mm thick tinted sheet glass fixed in window/door shutter ordinary quality n exc. 0.5sqm in each pane complete all as specified and directed.

Supply only galvanised mild steel wire clothes 0.46 mm nominal dia of wire and average width of aperture 1.4 mm complete all as specified and as directed . Note : Fixing only rate is included in window/door shutter item considered therein.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,all as specified and directed

M&L for cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

S&F for Roof trusses (Framed), trussed, purlins, crane gantries, rails and fastening and heavy brackets framing(Beam, tee, angle, channel or flat section) including distance pieces, cleats, etc. Gde Fe 410-W (Gde-E-250) quality-A all as specified and directed.

S&F Mild steel, plain, black sheet 1.25mm in hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes unched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and directed

M&L for 2mm thick Fibre glass reinforced translucent corrugated sheeting (approved color and pattern) with two corrugations side lap fixed with coach screw and washer in roof, wall etc incl L type or J-type hook instead of screw complete all as specified and directed

Cutting holes into or through brick walls built in cement mortar for superficial area exc 150Sqcm but n exc 400 sqcm and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required.

M&L for preparation of new steel surfaces over 10cm width or girth of any description and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Dismantling of interlocking paver block/ Bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer) Laid dry and pointed etc complete

Demolition of cement concrete in ground floors and pavings not exc. 15 Cm thickness (below/above ground level) including floor finishes complete all as specified and directed

M&L for cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete to be laid in required slope complete all as specified.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade (with grey cement and no pigment) over sand cushioning complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

M&L for Providing, cement concrete 1:2:4 type B1 in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including neccessary formwork.

M&L for Providing & fixing false ceiling at all heights (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, 12mm thick semi perforated micro tegular edges having moisture micro tegular edged GRG false ceiling or 10 mm content less than 2%, humidity resistance edged GRG thick square edged of 99%, NRC0.50 to 0.75 as per IS false ceiling 8225:1987, ncombustible as per BS tiles 476 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of mainT runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm , suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1OOOmm length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-inCharge.

S&F 12mm thick toughened frosted glass pane area exc 0.50 sqm in each pane fixing as door/ windows or partition with rubber gasket , glazing clips and beading and necessary fittings i.e SS holding clips for partition and cutting holes in required shape and size as directed including filling gaps with sillicon gel using gun etc complete all as specified and directed

M&L for 12 mm thick Plywood( No of ply should not less than 7), grade BWP, type BB fixed with screws to timber frame work

M&L for 0.9mm thick decorative laminate type 1 of surface finish (colour and pattern as approved) fixed with approved adhesive as per manufacturer's instructions

S&F magnetic catches for cabinets of size 50 mm complete with striking plate & magnetic stud complete all as per approved smaple complete all as specified and directed.

M&L for 150 mm dia Reinforced concrete pipes, class NP3, laid and jointed complete with collars as specified and directed.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 200 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished ,and reforming benching as required for 150 mm internal dia of pipe complete all as specified and directed.

M&L for Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM 1:4 complete all as specified and directed.

M&L for preparation of old decorated plastered or unplastered surfaces and applying one coat of white wash on wall and cleaning premise clean & tidy complete all as spec and dir by Engineer-in-Charge.

M&L for preparing of old distempered surface of wall and applying one coat of oil bound distemper complete all as specified and directed.

Hacking out old broken glass of ( any thickness, size or quality from wooden or metal frame glazed with putty or beads/cleat etc complete all as specified and directed.

S&F 3mm thick plain sheet glass fixed with oil putty, ordinary quality n exc. 0.5sqm in each pane complcomplete all as specified and directed.

S&F Vitreous china wash hand basin (550X400mm) white, flat back excluding taps but including heavy duty brackets & CP waste coupling 32mm, LDPE waste pipe 32mm upto floor trap complete all as specifed and directed.

S&F 15mm bore dia Chromium plated stop valve/angle cock, but fancy type, chromium plated with long shank and cup (concealed type) and fixed complete all as specified and directed

S&F CP SS Soap dish premium quality, fixed to wall with plugs and screws complete all as specified and directed.

S&F CP towel ring of approved design and pattern by GE all as specified and directed.

S&F rotational moulded polyethylene water storage tank 250 ltrs cap cyllinderical vertical with closed top hoisted and fixed in position at roof or stand all as specified in SSR Pt-I complete all as specified and directed

S&F 20mm Ball (float) valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron/pvc/cpvc pipe in water tank and fixed. (Minimum weight 25mm-455gms) complete all as specified and directed

Excavation through PCC floor upto maximum depth of 0.50m for fixing of PVC floor trap and connection to outlet pipe through brick or stone walls complete all as specified and directed

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard dense soil incl returning filling complete

S&F 16-17mm thick Prelaminated particle board, interior grade,but prelaminated both sides with decorative choice laminations, fixed to frame work complete all as specified and directed.

Extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails complete all as specified and directed

S&F 2nd class hard wood plain fillet sq. rect and triangluar in section, wrought secured with sectional area exc 13 but n exc 25 sqcm complete all as specified and directed

S&F 75mm size Hasp and staple, aluminium anodised, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed

S & F 30mm Continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and directed

S&F magnetic catches for cabinets of size 50 mm complete with striking plate & magnetic stud complete all as per approved smaple complete all as specified and directed.

S&F 100 mm size Extruded aluminium alloy handles, fabricated type., anodised handles all as specified and directed.

Excavation in post holes through PCC floor (or similar holes) each n exc 0.5 cum getting out returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n exc 50 M and making surface good in PCC 1:3:6 complete all as specified.

M&L for Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc Gde Fe 410-W (Gde-E-250) quality-A all as specified and directed.

S&F 8mm Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of Fe-410- W(Gde- E-250) quality- B

Taking down steel rolling shutter of size not exc 45 Sqm each with complete fittings (except side rail)

S&F 1.25mm thick laths Steel rolling shutters, but gear operated type with bevel gear box and crank handle, as specified including top cover, anchoring rod, hasp and staple one shop coat of primer; erected in position as indicated, including provision of required portion of shutter without sheet (grill only) as directed by Engr-in-charge.

S&F Safety lever locks mild steel with 4 levers for rolling shutters

S&F Ball bearing for rolling shutters of suitable size required at site complete all as spec and directed.

Extra for wicket door in steel rolling shutter including a 4 lever mild steel safety lock, lockable from both inside and outside

S&F galvanised steel wire of 25x25mm mesh size netting of 1.40mm dia fixed with tinned tacks of wire staples

M&L for complete removal of existing treatment using mechanical wall sander ( having mechanical vaccum mechanism) with RPM not less than 1500, sanding pad of 80 grit of dia 7"/ 9"on walls (external surface) and applying one coat of exterior wall care putty 2mm thick complete all as specified and as directed

M&L for Preparation of old decorated surfaces of walls, fascia chajjas etc incl brooming and applying two coats of exterior weather proof water based emulsion paint over one coat of compatible primer complete all as specified and directed.

M&L for preparation of old decorated plastered or unplastered surfaces and applying two coat of white wash on ceiling complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

Taking down carefully copper & aluminum point wiring for light, fan, socket or power complete and making good distrubuted surfaces of walls floors etc. Including switch & socket etc complete all as specified and directed by EIC.

Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with mild steel/pressed steel sunken boxes( with earth dolly) duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:-

One light point controlled by one switch.

One ceiling Fan/ wall mounting point controlled by one switch.

One exhaust Fan point controlled by one switch.

One 3 pin socket outlet on same board.

One 3 pin socket outlet 5 Amps on independent board.

Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 4 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with mild steel/ pressed steel sunken boxes with earth dolly duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets etc, including PVC insulated multi-stranded copper conductor 4 Sq mm nominal cross sectional area single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the one 3/5 pin 15/16 amps socket outlet independent.

S & F in repair incl making existing surface good sheet metal enclosures with socket plug top and MCB's with two pin and earth plug and socket complete with one single pole MCB 240 V grade 20 Amp.(A/C Box) complete all as specified and directed by EIC.

S & F in repair of modular switch single pole one way 16 Amps, 1 module ISI marked complete all as specified and directed by EIC.

S & F in repair of modular socket single pole one way 6/16 Amp-2/3 PIN, 2 module ISI marked complete all as specified and directed by EIC.

S & F in repair of modular switch single pole one way 6 Amps, 1 module ISI marked complete all as specified and directed by EIC.

S & F in repair of modular Socket single pole one way 6 Amp-2/3 pin, 2 module ISI marked complete all as specified and directed by EIC.

S & F of modular white cover plate with frame, 4 module ISI marked complete all as specified and directed by EIC.

S & F of modular white cover plate with frame, 6 module ISI marked complete all as specified and directed by EIC.

S & F of modular metal flush box ,4 module ISI marked complete all as specified and directed by EIC.

S & F of modular metal flush box, 6 module ISI marked complete all as specified and directed by EIC.

S & F in repair of 1 x 18 watt LED tube light fitting basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver, LED Decorative luminaire with suitable for lamps LED Light high efficiency LED driver,Optimized heat dissipation for ensuring high LED life span.

Taking down existing U/S fittings any type any size and Supply & Fix LED 10 watt tube light fitting integrated type, (Length min 2 feet), 240 V, PF >0.90, colour temp 6500K, suitable for surface mounting on wall, multi stranded copper flexible cable 0.5 sqmm Two core, and PVC round block white colour x 2 Nos for mounting of fitting complete all as as directed by EIC.

S & Fing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by EIC.

S & F in repair Ceiling rose, 3 phase/PVC/ polycarbonate, isolated body complete all as specified and directed by EIC.

S & F modular ceiling Fan step regulator, 120W - 2 module electronic step type 240 Volts, ISI marked with valid CML No. and connecting up complete all as specified and directed.

S&F Exhaust Fan 300 mm sweep with louver complete metal body complete all as specified and directed by EIC.

Taking down carefully aluminium sub main wiring from the existing casing/caping/PVC conduit all as diretced by EIC.

Material & Labour for sub main wiring with two run of 6 sqmm size PVC insulated multi stranded copper conductor FRLS cable (Nominal area) and one run of 6 sqmm size PVC insulated unsheathed solid core copper conductor cable drawn in existing surface/ recessed steel/ PVC conduit/ PVC casing capping of required size complete all as directed by EIC.

S & F in repair including taking down sheet metal enclosure for MCB DB, SPN 230 Volts 200 amps rated busbar 8 way double door complete all as specified and directed by EIC.

S & F in repair of MCB single pole with neutral 240 volts 32 to 40 Amps with thimble suitable for existing wires complete all as specified and directed by EIC.

S & F in repair of MCB single pole 6 to 32 Amps 240 V with thimble suitable for existing wires complete all as specified and directed by EIC.

S & F electric water heater (Geyser), storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece complete all as specified and directed by EIC.

S & F water proof decorative flexible LED strip 8W , with uniform light distribution , IP65 rating , High withstand capability, for writing the name as required on ground complete with all accessories for fixing of light complete all as specified and directed by EIC.

S&F in repair of LED Building security light fitting 1x 25 W new generation energy saving and environmental friendly long life made up of pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening seprate driver compartment with IP 66 protection and impact resistance of IK07 for mounting existing bracket complete including all accessories pre-wired with 3 X 1.5 sqmm single core mutistrand copper conductor cable up to celing rose/ terminal box and proper earthing connection must be provided, all as specified and directed by EIC.

S&F wall mounting fan 300 mm sweep,2150 RPM, with air delivery 90 CMM and power 115 Watt complete all as specified and directed by EIC.

S&F sheet metal enclosure for VT DB TPN, MCCB DB TPN 4 way, with 200 A rated bus bar, double door with 100 Amp,25 KA,TP MCCB as incomer (Vertical type double door,100 Amps MCCB rate inclusive) and suitable for SP/TP DB in outgoing, enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 including wooden rectangle board of first quality of suitable size for mounting of DB box with provision for 4 Pole MCCB* as incomer and SP/TP MCBs as outgoings complete all as specified and directed by Engr-in-charge:

City buildcom builders & devlopers (BID ID -3132532)

M/s H V Infra Projects (BID ID -3137609)

M/S RAKESH TRADERS (BID ID -3141415)

Samaksh Enterprises (BID ID -3133212)