Construction of Market Complex at Nagar Nigam

Amount

Construction of Market Complex

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts. Leveling ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/I. Extra for earthwork in hard soil as per specification and direction of E/I. (vide classification of soil item

Earth work in Excavation of cut off trenches by the hydraulic excavator as per designed section in soft rock (Where blasting is not needed ) (Vide type of soil item-C) with disposal of spoil beyond 150 m from center of trench but upto 500 m with all lifts by tipper including construction and maintenance complete as per approved design,bulding specification and direction of E/I

Filling in foundation trenches and plinth in layers not exceeding 150mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume)

Providing coarse clean sand in filling in foundation trenches or in plinth & floor including ramming & watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering texes royalty all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shutfering All work up to plinth level:1:2:4 (1 cement: 2 coarse sand (zone-1) :4 graded stone aggregate 20 mm nominal size)

Providing P.C.C. M-150 in nominal mix of (1:3:6) in foundation with approved quality of ston chips 20 mm to 6 mm size graded and clean coarse sand of F.M.2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position . Vibrating ,striking ,curing ,taxes and royalty all complete as per building specification and direction of Engineer-in-Charge.

Providing and laying Double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622/ ISO 13006, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. complete Size of Tile 600 x 600 mm

Providing and laying Double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622/ ISO 13006, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. complete Size of Tile 600 x 600 mm

Provrcting and laying 25rnm. thick kotah stone slab flooring of approved size, iexture and colour over 19mm. thick base of lime morter (1 1 :1) (lime putty:surkhi:coarse sand) laid over and jolnted with grey cement slurry mixed with pigment to match the shade of slab including rubbing and pollshrng to granolithic finish with approved quality of carborandurn stone including cost of curing, taxes and royaliy all complete as per building specificationand direction af Ell. (i) 300X300 rnm size

Providing and laying 25mm. thick kotah stone tiles in risers of steps, skiiting and pillars of approves size, texture and colour laid cover 12mrn. thick cement mortar (1:3) and.loined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolilthic finish with approved quality of carborandurn stone including cost of curing, taxes and royaliy all complete as per building specificationand direction of El.

Providing and laying in positionspecified grade of reinforaed cement concrete, excluding the cost of centering, shutterhe. finishing and reinforcement- All work upto plinth level. 1.5:3 (1 cement: 1.5 course sand (zone-1): 3 graded stone geregate 20 mm nominal size)

Reinforced cement concrete work in wals (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets column pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering& finishing and reinforcement : 1:1.5:3 cement: 1.5 coarse sand (zone-l):3 graded stone ag8regate 20 mmnominalsize)

Providing R.C.C.M-200 with nominal mix of (1:1.5:3) in beams with approved quality of stone chips 20mm.to 6mm. Size graded and clean coarse sand of F.M. 2.5.to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement, taxes and royalty all complete, as per building specification and direction of E/I.

Providing R.C.C. M-200 with nominal mix of (1:1.5:3) in staircase with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including centering, shuttering, screening, mixing cement concrete in mixer, placing in position vibrating, striking, curing taxes and royalty all complete as per building specification and direction of E/I.

Centring and shuttering including strutting, propping etc. and removal of form for foundation, footings, bases of columns etc. for mass concrete.

Centring and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts

Centring and shuttering including strutting, propping etc. and removal of form for lintel, beams, plinth beams, griders, bressumers and contilevers.

Centring and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform.

Providing designation 75A brick work in C.M (1:4) in foundation and plinth approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. Thick morter joints, cost of screening, materials, scaffolfing, raking out joints to 15mm. Depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75B brick work in C.M.(1:6) in foundation and plinth approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. Thick morter joints, cost of screening, materials, scaffolfing, raking out joints to 15mm. Depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75A brick work in C.M.(1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. Thick morter joints, cost of screening, materials, scaffolfing, raking out joints to 15mm. Depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 125mm. Thick reinforced designation 75A brick work in C.M. (1:4)in superstructure with approved quality of clean corses sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials, scaffolding, raking out joints to 15mm. depth, curing, texes and royalty (but excluding the cost of reinforcemrnt) all complete as per building specification and direction of E/I.

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing 12 mm , cement plaster (1:4)with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water ,scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 12 mm , cement plaster (1:6)with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water ,scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 19mm thk. Water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other water proofing compound including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm thk. Water proof cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per builing specification and direction of E/I.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound Conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineerin- Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing two coats of dry distemper of approved shade and make over a primer coat of washing over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/I.

Providing two coat of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/I

Providing two coats of plastic emulsion paint of approved shade & make over a coat of cement primer on new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty whereever required, scafffolding, washing of floors & taxes all complete as per building specification and direction of E/I

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of

Providing two coat of synthetic enamel paint over a coat of primer of approved shade and make over new wooden & surface after cleaning, removing dirt, scales, smokes, grease and sand paper, including cost of scaffolding and taxes all complete as per building specification and direction of E/I

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I

S/F/F good quality wall dressed and well seasoned local wood work in chaukhat in doors, window skylights, fanlights and C/W celestial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/I.

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

S/F/F fully glazed steel door windows or ventilations of standard rolled ‘Z’ and mullion steel sections and size as per IS-1038 joints met and welded with 100 x 16 x 3 mm M.S. lugs fixed in cement concrete (1:2:4) blocks 15 x 10 x 10 cm size including cost of oxidized iron fittings, with hinges, handle per steps, catch springs, 3 mm thick plain glass panes with aluminum beads and inner frame fixed with lugs with 20 mm long 6.3 mm G.I. counter sunk machine screw and nuts and applying a coat of red lead paint carriage to work site hoisting and placing in position in all storys and taxes all complete as per building specification and direction of E/I.

Supplying fitting and fixing 35mm thick solid core type decorative double leaf flush door shutters.

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

S/F/F 30 mm thick solid core type non-decorative single leaf 1/3rd glazed flush shutters in doors and windows with black board core bended with high quality phenol formal dehydes synthetic resin both side commercial veneered of standard make with top glazed of size 95 cm x 20 cm or as specified fitted with 3 mm thick glass panes of standard make with oxidezed iron fittings such as hinges, tower bolts, handle cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover sqm

Supplying, fitting and fixing MS grill gate made of 20x6mm MS flat or 16mm square bars fitted on 25x25x6mm. MS Angle frame.

TMTC-500 8mm dia

TMTC-500 10mm dia

TMTC-500 12mm dia

TMT-500 16mm dia

Providing & fixing Fan hook of 16 mm. dia. M.S. bar 1 Mtr. Long bent to required size and shape, placed in position and fixed in Truss Frame / RCC Slab / beam at the time of casting all complete as per building specification and direction of E/I. (Where materials is not supplied by deptt.)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20mm nominal size ) over 75mm bad by dry brick ballast 40mm nominal size well rammend and consolidated and grouted with fine sand including finishing the top smooth.

Providing and laying 60mm thick facTory made cement concreteinterlocking paver block of M -30 grade made by block makingmachine with strong vibratory compaction, of approved s;ze, design& shape, laid in required colour and pattern over and including 50mmthick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing 250mm. wide brick drain in cement morta(1:6)with av.150mm. clear depth and 250mm. apron including cost of earthwork involved with 75mm. cement concrete ('1:4:3) over one brick designation 75A,flat soling in proper grade and slope at the base,the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Providing and fixing factory made laminated veneer lumber glazed shutter conforming to IS: 14616 and TADS 15:2001 (Part B), using 4 mm thick float glass panes for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, all as per directions of Engineer-in-charge (Note:- Butt hinges and necessary screws shall be paid separately)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

(i) C.I. cover and frame 300 x 300 mm inside

(ii) S.C.I. plain bend 100 mm dia

(iii) S.C.I. Tee 150 mm dia

Cost of drilling 200mm x 165mm x 125meter deep bore well in all kinds of soil and rock in rural area for installation of pump set with hydraulic DTH Rigmachine ,all complete including supplying all materials, tools ,drilling rig,Air compressor and equipments ,as well as fuel,lubricants and cost of transportation of Rig machine and other vehicles up to the site. (I) From 0-50 meter

(II) From 51-125 meter

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Supplying,tools tackels & lowering of 200mm dia MS Erw Casing Pipe Of 6mm wall thickness including welding charges , cost of Pipe etc including all taxes, vat, Excise duty,freight charges with inspection charges etc as applicable,etc all complete job

100 mm nominal size dia

150 mm nominal size dia

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete : 150 mm clamp

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying all materia. Labours,tools & equipments for fitting & fixing 200 mm dia MS cap over casing Pipe Complete job.

Horizontal

Vertical

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore

submersible pump set 100mm dia (with polypropylene/nory impeller) up to 20 stage. 5 HP

Supplying XLPE /PVC insulated,armoured cable 1100 v grade with ISI mark Three and half core standerd aluminium conductor with 6 mm thick 25mm width M.S spacer with G.I earth wire 6 mm thick 25mm width with G.I earth with 6 sq mm , complete in an approved manner. 3.5 core 25 sq mm

STARTER

12.5 lit. low level C.I. cistern

Supplying, fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S approved make supported on painted C.I. or R.S. brackets 32mm C.I. brass waste, 15mm dia C.I. body spindle stop cock of approved quality of weight not less than 350grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

100mm dia

75mm dia

100 mm dia (wt. 5.5 kg. app)

80 mm dia (wt. 4 kg. app)

100 mm dia (wt. 15.5 kg. app)

80 mm dia (wt. 15.5 kg. app)

100mm dia

100mm dia (wt. 3.25 Kg appx.)

110 mm diameter

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

110 mm bend

110 mm Shoe

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

15 mm dia

20 mm dia

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

100 mm diameter S.W. pipe

15 mm nominal bore

20 mm nominal bore

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Group C

Supply of 300 mm, 230V A.C exhaust fan.

Supplying and fixing Surface mounted 18/20 watt LED downlighter complete with integrated electronic driver & LED directly on ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

15/16 Watt LED Bulb

LED FLOOD LIGHT 75/80W

Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc, as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box but excluding modular plate as required.

Earthing with G.I. earth pipe 4.5mtr. long 40mm dia including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal or coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc., as required.

Supplying and laying 25 mm X 6 mm G.I strip at 0.50 metre below ground as strip earth electrode, including soldering etc.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Earthing with G.I. earth plate 600mm x 600mm x 3mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required.

Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete etc. as required (horizontal run).

Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete etc. as required (vertical run).

Laying copper/ G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

3.5c x 95 sq.mm

11 KV cable laying upto 120 sq.mm. in same trench :- Laying of one number PVC insulated and PVC sheathed /XLPE power cable of 1.1kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

3.5c x 95 sq.mm (45mm)

Above 35 sq. mm and upto 95 sq. mm

4 Way (4+12) Double Door, Horizontal type

6 Way (4+18) Double Door, Horizontal type

40 amps TPN

63 amps TPN

6/32 amps DP

4R X 6 sq. mm + 2R x 6 sq.mm Earth Wire

4R X 10 sq. mm + 2R x 10 sq.mm Earth Wire

Wiring for light/ power plug with 2X4 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1Nos 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

2R X 2.5 sq. mm + 1R x 2.5 sq.mm Earth Wire (Switch Boards)

Telephone Socket outlet modular type

Modular base & cover plate for 1 Module

One pair

Supplying, Installing, Testing & Commisioning cost of Power Distribution Boards (PDB-1) all complete with all necessary items as per direction of E/I.

FEEDAR PILLER

Silent type D.G. set of capacity 62.5 KVA three phase with AWF PANEL IS /IES-60034-1

Terrace Booster Pump

80 mm diameter

100 mm diameter

150 mm diameter

80 mm diameter

100 mm diameter

150 mm diameter

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

150 mm diameter

100 mm diameter

80 mm diameter

65 mm diameter

50 mm diameter

40 mm diameter

32 mm diameter

25 mm diameter

Providing and fixing S.S Fire Hydrant Valve of approved quality with 63 mm female, instant, ovlique, single outlet, 80 mm flanged inlet, brass spindle, cast iron wheel m A.B.S. blank cap and chain. conforming to IS: 5290 complete with companion flange, bolts, nuts, rubber insertion / compressed asbestos gasket etc. and painted in fire red colour.

Providing and fixing swinging, wall mounting type First Aid Hose Reel of approved quality and made from compresed steel sheet with dust cover, cast iron brackets including 30 m long, 19 mm nominal bore, high presure braided rubber hose as per IS:444 Type hose guide, PVC shut off nozzle with 6 mm outlet and 25 mm nominal bore gun metal inlet valve, bolts, nuts rubber insetion etc. painted in Fire red colour including cutting and making good the walls wherver required.

Providing and fixing in position 63 mm nominal bore and 15 m long synthetic fibre, CP fire hose pipe of approved make bearing IS: 636 -1988 type A mark and having TAC and MMD approved with a pair of 63 x 63 mm gun metal instantaneous type, heavy duty delivery hose coupling (conforming to IS: 903) bound and riveted to the hose pipe with copper rivets and copper wire complete.

Providing and fixing in position short SS brach pipe of approved quality with 63 mm male instatneous type inlet and 15 mm outlet nozzle complete conforming to IS : 903

Providing and fixing Standard response sprinklers with quartzoid bulb overating temperature 68 degree centgrade, of 15 mm orifice and k factor 80 (5,6) made out of forged brass and chrome finish. Make:Safex/Atasee/Tyco

Supplying, fixing, testing & commissioning of 1 set of 63mm two way instantaneous fire brigade connection (FBC) with inbuilt NRV comprising of SS and four SS instantaneous male inlet coupling confirming to IS:604 with plug and cap with chain as required with nut & bolts, washers, high pressure gasket as required.

Cement

Local Sand

Stone Chips

Brick

Steel

Providing and fixing Coat Hook of approved quality.

Supplying,Storing,handling,shifting,installation,testing and commissioning of CP flxible hose, spary wall flange etc.complete (1) Kerovit make (model-KA580002).(2) Hindware make model-F1600002)Rs.=1570.(3) Parryware Make (Model-T9941A1) Rs.=1600

Providing and fixing straight type macfit single body push fit type WC pan connector with factory supplied spring loaded seal guard of Mcalpine,UK with intergral single mould sealing fins made of flexble EVA body,including bush/adoptor for use with C.I Pipe as supplied with the pan connector.

Supplying and fixing single wall mounted 18/22 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.

Supplying and fixing batten/ angle holder including connection etc. as required.

For Terrace Pump

3 × 10 sq.mm.(aluminium)

Pressure Gauge Assemble with Gate/Ball Valve

Air release Valve / Drain Valve

Providing and fixing 25 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)

Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.

Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)

Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)

Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)

Supplying, installation, testing and commissioning of duel tone electronic hooter / Flasher / Strobe suitable for wall mounted complete as required. Make:Honeywell/Seimens/ Qutak/ Bosch

Supplying, installation, testing and commissioning of manual call box in suitable enclosure with arrangement to raise the alarm when the glass is manually broken complete as required. Make:Honeywell/Seimens/Qutak/Bosch

Supplying, installation, testing and commissioning of microprocess base main fire alarm control panel with LCD Display lights. The panels shall have 240 volts AC power supply automatic Battery charger 24 Volts sealed lead acid maintenance free battries as complete with batteries, battery charger illuminated numeric digram complete as required. Make:Honeywell/ Seimens/ Qutak/ Bosch

Providing and laying 19mm dia PVC conduit complete with required junction boxes in recessed / surface system PVC insulated copper conductor cable of 2x1.5 sq.mm. in existing conduit as required. Make:Polycab/Mescab

Add 12% GST (in basic rate must enter 12)

Add 1% Labour Cess (in basic rate must enter 1)

BHARDWAJ TECHNOINFRA PRIVATE LIMITED

Sharda Shelters Pvt. Ltd.

M/S ADARSH CONSTRUCTION