CLEANING/MAINTENANCE OF OHT RESERVIOUR, UG SUMP, RISING MAIN, DISTRIBUTION, SWIMMING POOL AND CERTAIN OTHER E/M MAINTENANCE WORKS AT AF STN CHANDINAGAR UNDER AOR OF GE (AF) FARIDABAD

Amount

M&L for draining out sedimentation sludgy water from RCC OH reservoir 50000 Glns capacity - 02 Nos at 60 feet stagging and Semi UG Sump including scrapping out sticken foreign material from inner side of OH and Semi UG sump walls/Ceiling by wire brush and removing excavated sedimentation manually and depositing 50 mtr away from OH tank and flushing out the floor with fresh water till satisfaction of Engineer in Charge, providing two coats of white wash on old prepared surface, cleaning of after completely draining out water from the tank, Writing the cleaning date on the tank, complete all as specified and directed. Note:-The cost of the same shall be deemed included in the respective items. All T&P required for the cleaning of tanks / sumps will be arranged by the contractor.

M&L for draining out sedimentation sludgy water from Swimming Pool & Diving Pool 02 Nos including scrapping out sticken foreign material from inner side and walls/Ceiling by wire brush and removing excavated sedimentatation manually and depositing 50 mtr away from Pool and flushing out the floor with fresh water till satisfaction of Engineer in Charge after completely draining out water from the Pool, Writing the cleaning date, complete all as specified and directed. Note:-The cost of the same shall be deemed included in the respective items. All T&P required for the cleaning of tanks / sumps will be arranged by the contractor.

S&F in replacement of fully automatic star delta submersible starter with short circuit protection in sheet metal enclosure suitable for 50 HP, 415 Volt, 50 Hz with over load protector and phase preventer and taking out old U/S starters of any type and any capacity complete all as specified and directed.

Supply, fixing & testing of 200mm dia. UPVC pipes (IS: 4985-2000 class 'V', 10 Kgf/cm2 pressure rating) (quick fit pipes) including injection moulded fittings (heavy duty) (plain or door) i.e bends, junction, cowls, tees, elbow, sockets, tee, tail pieces, Flanges, offsets, access pieces etc. Clamps/Supports jointing with rubber ring /solvent cement joints including cutting chase or holes in walls and floors and making good as required at Site including taking off old u/s, complete all as specified and directed.

All as per iItem No 04 above but for 160 mm with 10 Kgf/cm2 pressure rating.

All as per Item No 04 above but for 140 mm with 06 Kgf/cm2 pressure rating.

All as per Item No 04 above but for 110mm with 06 Kgf/cm2 pressure rating.

M&L for UPVC Pipe fittings such as bends, tees, collars, tail pieces, flanges, reducer, elbow, sockets etc, suitable for UPVC mains of sizes upto 200 mm dia. pipes, complete all as specified and directed.

M&L for Repair of UPVC line, any type of lines for stopping the leakages including excavation up to 10 RM complete all as specified and directed. Note :-1.Excavation more than 10RM shall be measured & paid separately . 2.Using T&P with UPVC fittings such as Nipple , socket , tee ,Elbow, bend etc (Pipe fitting shall be measured and paid separately).

Supply only UPVC Tail Pieces 110 mm bore.

Supply only UPVC Tail Pieces 140 mm bore.

Supply only UPVC Tail Pieces 160 mm bore.

Supply only UPVC Socket 100 mm bore.

Supply only UPVC Socket 160 mm bore.

Supply bore UPVC Tee 140 mm bore.

Supply only UPVC Elbow 140 mm bore.

Supply only UPVC Elbow 160 mm bore.

Supply only UPVCReducer 140 mm to 160 mm bore.

Supply only UPVC Reducer 160 mm to 200 mm bore.

M&L in replacement of unserviceable water type Cast Iron, butterfly valve, class PN-1.0/15 PSI (As per existing) of size 150mm dia (OD 160mm) having matching flange complete all as specified and directed.

M&L in replacement of unserviceable water type Cast Iron, butterfly valve, class PN-1.0/15 PSI (As per existing) of size 100mm dia (OD 110mm) having matching flange complete all as specified and directed.

Supply and fixing in replacement of unserviceable water type Cast Iron, butterfly valve, class PN-1.0/15 PSI ( As per existing) of size 140 mm dia having matching flange complete all as specified and directed.

Supply only chlorine test kit with PH colured sample, complete with all testing fitment and OT solution in rexine box complete all as specified and directed.

M&L for chemical and bacteriological analysis of raw water collected from all the pump house situated in AF station chandinagar, complete all as specified and directed.

M&L for chemical and bacteriological analysis of chlorinated water collected from distribution line Pump House No 1 situated in AF station chandinagar complete all as specified and directed.

M&L for "lifting and Lowering of any acpacity" Submersible Pump Set of capacity 30 HP for repair/ Overhauling /rewinding /devolpment including increasing the length of delivery pipe/or any other requirement at site at tube well installation at AF Station chandinagar with manpower/Chain Pulley arrangement including shifting to local workshop for repair and bring back after repair, at site, including testing and commisioning complete all as specified and directed. Note :- Any minor part, if required, shall be provided by contractor and deemed to be included in quoted rate without any extra cost.

All as per item No 26 above but Capacity of 10 /15 HP.

M&L for Dismantling and strip opening of burnt submersible pump of capacity 30 HP including cuttting, removing, burnt winding wire from stator assembly and preparing slots, rewinding the same with super enamled water proof copper winding wire of suitable gauge with necessary insulation materials, varnishing etc and re-assembling stator rotor assembly with pump testing, commmisioning such as (i) Impeller GM . (ii) Distance bush SS.(iii) Guide Bush (iv) Neck ring gun metal (v) Impeller key (vi)Guide van (vii) Sand Guard including tranportation to local work shop etc complete all as specified and directed.

All as per item No 28 but 10 /15 HP

M&L for Dismantling and strip opening of burnt Booster pump motor of capacity upto 10/15 HP including cutting removing burnt winding wire from stator assembly and preparing slots, rewinding the same with super enamled water proof copper winding wire of suitable gauge with necessary insulation materials varnishing etc and re-assembling stator rotor assembly with pump testing, commissioning including tranportation to local work shop etc complete all as specified and directed.

M&L for replacement of Submersible cable flat PVC insulated Sheathed copper conductor, 10sqmm, 3 Core, 2 run, complete all as specified and directed.

S&F in replacement of self priming re-circulation pump set of capacity 3 HP / 3000 RPM, Head - 14 Mtrs induction motor ( Mono block pump set ) type with fitted on trolly mounted for swimming pool as per existing make and model complete all as specified and directed.

S&F in replacement of unserviceable PVC insulated Three core multi stranded copper conductor cable 4 Sqmm complete all as specified and directed.

S&F in replacement of Suction sweeper/ Vaccume Cleaner of SS ( 10" width and 03 feet length) trolly mounted with 03 HP pump set complete fittings for connecting hoses and 3' SS head ( including Leaf net, wall brush, telescopic pole 4.8 m ) complete set of suction sweeper / vaccume cleaner of PVC pipe 50mm dia complete all as specified and directed.

S&F in replacement of PVC suction hose flexible pipe of 50 mm dia and rope with 2 male connector nipples, clamp etc complete all as specified and directed.

S&F in replacement of heavy duty swimming pool cleaner wall brush with Aluminium handle with stainless steel bristles, width 18" and 7' feet height/length of handle complete all as specified and directed.

Disconnecting and dismantling of pump set from the foundation, breaking the existing defective PCC foundation in any size & shape. M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate for foundation of any size of motor pump set from 50 HP to 75 HP capacity pump set and fitting pumping set in position with base frame painted with synthetic enamel black paint complete all as specified and as directed.

Supply and fix in repairs Decrin dozing pump, 100 PSI, 40 GPD Capacity and testing complete all as specified and directed.

Supply and fix in replacement of FRP TANK of Capacity as per existing with level gauge with agitator Motor ,connection shaft and mixing blade complete all as specified and directed.

Supply and fix in replacement of Electric motor, Single phase, 50 HZ, 1/8 HP assembly Suitable to mount on decrin mixing tank along with agitator shaft and blade complete all as specified and directed.

Supply and fix in replacement of connection pipe suitable for connecting to decrin dosing pump to Header( 2 mtr long, 8 mm internal dia) complete all as specified and directed.

Supply and fix in replacement of circuit of speed of Dozing pump complete all as specified and directed.

Supply and fix in replacement of Injector Nozzle for Decrin dozing pump complete all as specified and directed.

Supply and fix in replacement of Regulator Knob for dozing pump, complete all as specified and directed.

Supply and fix in replacement of power cord for dozing pump 2 mtr long plug top 5 AMP 240 volt AC complete all as specified and directed.

S&F in replacement of 3 pole power contactor with NO / NC block suitable for MNX 50 to 110 complete all as specified and directed.

S&F in replacement of 3 pole power contactor with NO / NC block suitable for MNX 40 to 45 complete all as specified and directed.

S&F in replacement of 3 pole power contactor with NO / NC block suitable for MNX 25 to 32 complete all as specified and directed.

S&F in replacement of 3 pole power contactor with NO / NC block suitable for MNX upto 18 complete all as specified and directed.

Supply and fixing in replacement of MCCB, 63 Amps, 415 volts, TP, 16 KA, complete all as specified and as directed.

Supply and fixing in replacement of MCCB, 125 Amps, 415 volts, TP, 25 KA, complete all as specified and as directed.

M&L in replacement of Ladder for OHT/ UG sump with square bar, Angle iron, channel, Flat Iron etc, including welding, drilling, cutting with one primer coat, one under coat and one finishing coat of paint complete all as specified and directed..

S&F in replacement under water illumination Standard Underwater light 300W x 12 V (suitable for Existing ) Niche in Polypropylene and glass fibre with 3 mtr 4 sqmm electric cable and in ABS rim including water proofing jointing connection and tested all as specified and directed and Fiber Glass Disconnecting from supply and dismantling and repair of under water light fitting, water proofing, wiring, driver etc complete all as specified and as directed.

M&L for Deck Box in ABS with 3 entries of 3/4"or PG-16 coupling with necessary, connection and tested complete all as specified and as directed.

M&L for Flexible conduit hose, 1 m long for connecting light to the box 3/4" and M25 threaded ends complete all as specified and as directed.

S&F in replacement of unserviceable water proofing cable for lighting multi stranded copper conductor cable 6 Sqmm 02 core complete all as specified and as directed.

S&F in replacement of unserviceable water proofing cable for lighting multi stranded copper conductor cable 10 Sqmm 03 core complete all as specified and as directed.

M&L for rewinding of Low voltage swimming pool isolation transformer with protective shield between primary & secondary windings, internal protection against overload, 1500 VA, 230 V primary and and 12 V secondary voltage with tappings for different cable lengths. All necessary connections are required at site complete all as specified and as directed.

S&F in replacement of electronic timer, ET-100, 240/415, complete all as specified and as directed.

S&F in replacement digital type Ammeter as per existing size and type, complete all as specified and as directed.

S&F in replacement of digital type Voltmeter as per existing size and type, complete all as specified and as directed.

S&F in replacement of CT 30/5 to 200/5, complete all as specified and directed.

S&F in replacement of Indicating light with bulb, set of three, complete all as specified and directed..

S&F in replacement of unserviceable Single phase preventor VSP-2 complete all as specified and directed..

Supply and laying and testing in replacement Ductile Iron pipe of 150 mm bore with spigot and socket ends centrifugal cast, class K-9 as per IS 8329 in any length suitable for and including rubber tightening joints laid in trenches including taking down complete all as specified and directed..

Opening the pressure filter 1200mm dia Make-Pentair installed at swimming pool equipment room removing the old filter media, removing all the scaling deposited on the surface area of filter assembly by using wire brush and cleaning the filter with HCL, refilling new filter media ( as per existing type) of various silica grade as required at site, re-assembling the filter assembly and apply one coat of good quality paint on the outer surface area of the filter assembly and testing for leakage for proper functioning and testing with the following specifications is maintained (a) Flow rate 125 m³/ Hr (Each), (b) Vessel dia-2000mm, (c) Filteration velocity 40m³/hr/m², (d) Working pressure 2.5 Kg/Cm² complete all as specified and directed..

Supply and fixing in replacement of 'On load' changeover switches, 4 pole, 200 Amps, 415 volts, open type fixed in existing panel allows changeover from main supply to generator supply & vice versa, complete all as specified and directed..

Supply and fixing in replacement of 'On load' changeover switches, 4 pole, 400 Amps, 415 volts, open type fixed in existing panel allows changeover from main supply to generator supply & vice versa complete all as specified and directed..

S&F in replacement of DOL starter for 10 HP with complete protection all as specified and as directed by Engineer-in-charge.

Material & Labour in repairs to existing LT panel board at Pump houses including painting with one coat of synthetic enameled paint to steel surfaces including preparation after scraping, filling, cavities etc, including replacement of damaged bus bar, lugs, copper wire etc all as specified and directed by Engineer-in-charge. Note :- U/S items to be replaced shall be measured & paid separately vide following items

Supply only MCCBs 415 volts, 4 pole, 16 KA, 100 Amps capacity complete all as specified and directed

Supply only Volt Meter 0 to 500 Volts digital square type 4”

Supply only Ammeter 0 to 200 Amps digital Square type 4”

Supply only Indicating Lamp set of three (Red , Yellow & Blue)

M&L in repair / replacement of Starter in existing LT panel board at Pump House pertaining to water supply and checking of electrical connection repairing to fault & replacement of U/S items complete including testing Commission complete to be entire satisfaction of Engineer-in-charge all as specified and directed. Note :- U/S items to be replaced shall be measured & paid separately vide following items

Supply only Contactor as per suitable in Existing Panel

Supply only spare kit without coil for contactor type as per suitable in existing Panel

Supply only Electronic timers as per suitable in existing Panel

Supply only over load relay as per suitable in existing Panel

Supply only for Fuse holder & Fuse bases suitable for in existing Panel

Supply only for start and push button for in existing Panel

Disconnecting / taking down / dismantling Solar flat plate collector of 100/125 LPD capacity for servcing, cleaning and repairing, brazing of tubes complete and re-assembled the same after repair complete all as specified and directed.

Descaling, cleaning of hot water and cold water tanks including heat collecting units with heat absorbing sheet etc for solar heating system of capacity 500 LPD complete all as specified and directed.

Descaling, cleaning of hot water and cold water tanks including heat collecting units with heat absorbing sheet etc for solar heating system of capacity 1000 LPD complete all as specified and directed.

Supply and fixing in replacement of electric Heating element 3 KW( for solar water heater) with thermostat for electrical Back up complete all as specified and directed..

Supply and Install SS Hot Water Tank of Capacity 500 Ltrs ( suitable for existing) double wall insulated with PUF Insulation machine injected, inner shell SS 316 and Outer Shell SS 304 Stucco Aluminium alloy coated coloured steel complete on roof tops at a height of 7 ft including connection of inlet and outlet water connections complete all as specified and directed..

All as per item No 87 above but capacity of 1000 ltrs

M&L for hot water pipe duly insulated with glass wool and aluminium cladding of 20 mm bore including taking down complete all as specified and directed..

M&L for hot water pipe duly insulated with glass wool and aluminium cladding of 25 mm bore including taking down complete all as specified and directed..

M&L in replacement of 25 mm dia. Gun metal gate valve with iron wheel head screwed both ends for iron pipe and fixed, including taking down complete all as specified and directed..

M&L for replacement of Gunmetal gate valve with iron wheel head screwed both ends for iron pipe and fixed 20mm dia including taking down complete all as specified and directed..

M&L in replacement of unservicable parts of solar water heater complete with servicable parts and making it servicable complete testing and commsioning and brazing of tanks for arrresting leakages complete all as specified and directed. Note :- Parts shall be measured and paid separately here in below as supply only.

Supply only following items for solar water heater 500/1000 LPD complete all as specified and directed..

Supply only Absorber Plate made of copper sheet, laser or ultrasonically welded to copper tubes ( Solar flat plate collector as per existing type) with Flanges L-1860 W-1240 H-100, weight 35-42 kg working pressure 490 KPA complete all as specified and directed.

Supply only Absorber Plate made of copper sheet, laser or ultrasonically welded to copper tubes ( Solar flat plate collector as per existing type) with Flanges L-1860 W-1240 H-100, weight 35-42 kg working pressure 1300 KPA complete all as specified and directed.

Supply only single pane 3.2 mm tempered low iron glass collector as per existing size and type complete all as specified and directed.

Supply & install 500 Ltr Cold water Tank of material SS-304( as per existing type) with Manhole & Stand complete all as specified and directed.

Supply & install 1000 Ltr Cold water Tank of material SS-304 ( as per existing type) with Manhole & Stand complete all as specified and directed.

Supply & install MakeupTank for heat exchanger of 5 Liter with ball cock complete all as specified and directed.

Supply & install Back Plact Collector complete all as specified and directed.

M&L for Servicing of OLD/ UNSV SOLAR street light fitting including servicing and Cleaning of solar panel, Low maintenance tubular battery by filling of Distilled water and first charging including replacement of damaged battery terminals, securing of all electrical wire circuit and connections, reparing of damaged foundation complete system if required or complete all as specified and directed.. Note:- 1. All type of T & P, Distilled water, control cable upto battery terminal, PCC, ladder & tripod etc required at site will be arranged by the contractor and rates for the same will be deemed to be included in the quoted rate. (Spares required to make functional of solar light shall be measured and paid seperately under relevent items here in below)

S&F in replacement of old U/S of Solar PV Module 74W( As per existing )

S&F in replacement of old U/S of White LED based light source 12W( As per existing )

S&F in replacement of old U/S of Driver of solar street Lights( As per existing )

S&F in replacement of old U/S of Battery rating of 12V & 100 AH( As per existing )

Supply & fix battery compartment box made up of MS sheet 2mm thick size suitable for battery with MS cover, locking arrangements & fixing accessories with inside weather proof coated & outside Aluminium paint including writing pole number in black colour paint etc complete all as specified & directed.

S&F in replacement of Integrated all in one Solar Street light (In-buit Solar PV module and Lithium battery) 24 watt, secondary optics, LED driver efficiency>92%, battery type LiFePO-04, IP66, colour temperature 6000K-6500K, 140 Lumens per watt Auto ON/OFF, overcharging protection including taking down old unser and complete fixing and connection all as per specified and directed.

M&L for Servicing of DG Set 200 KVA of any Make, checking entire system as per manufacturer's catalogue such as checking all parts for serviceability, taking down defective parts such as fuel filter assembly, by pass filter assembly, lube oil filter assembly, air cleaner assembly lube oil hose flexible pipe, hose turbo etc including replacement the same with same size, make and capacity of parts such as Fuel filter, Lube oil filter, Air filter, coolant and Engine oil ,hose pipe, Diesel filter with gasket etc and draining out the old used burnt engine oil from the oil sump and cleaning oil sump with suitable cleaning solution such as petrol and diesel or any other cleaning solution and refilling new engine oil required grade up to required level and including checking of AMF control panel, tightening of loose connections and testing to DG Set to the entire satisfaction of the Engineer-in-Charge. Note : (i) Engine oil shall be measured and paid for separately under successive items here-in-after. However, labour charge are deemed to be included in item rate above. (ii) Servicing shall be carried out by authorised dealer of manufacturer. (iii) Minimum 6 months gap / 200 Hrs of run whichever is earlier shall be considered for next service. (iv) Repair Guarantee for replaced parts/servicing of DG Set shall be for six month from the date of service.

All as per item No 109 above but DG set of capacity 180 KVA.

All as per item No 109 above but DG set of capacity 75 KVA.

All as per item No 109 abovr but DG set of capacity 62.5 KVA.

All as per item No 109 above but DG set of capacity 15 KVA.

S&F Fan belt set suitable as per existing for 15 kVA to 200 kVA DG Set of any type any make.

S&F New dehydrated Engine oil as required grades suitable as per existing for 15 kVA to 200 kVA DG Set of any type & any make, complete all as specified and directed. NOTE:- Engine oil will be suppied in manufacturer sealed barrel

Taking down of radiator from DG set (15 kVA to 200 kVA DG) of any type any make carefully cleaning of tubes and fins complete with the help of proper cleaning agent and wire brush soldering of tubes and fins at required places testing and refilling complete all as specified and directed.

Taking down of defective water pump from DG set (15 kVA to 200 kVA DG) of any type any make repair the same by water pump repair kit removing of leakage refitting after testing complete all as specified and directed.

M&L in replacement of water pump body assembly suitable for 15 kVA to 200 kVA DG Set of any type any make complete all as specified and directed.

M&L in replacement of self starter motor and charging alternator 24 volts complete set including dismantling and taking down old unser from DG set suitable for 15 kVA to 200 kVA DG set of any make any type complete all as specified and directed.

M&L in replacement of self starter motor and charging alternator 12 volts complete set incl dismantling and taking down old unser from DG set suitable for 15 kVA to 200 kVA DG set of any make any type complete all as specified and directed.

S&F in replacement of solenoid switch suitable for existing DG including all necessary arrangement for existing DG set of capacity 15 to 200 KVA complete all as specified and directed.

Supply only distilled water of best quality in 05 litrs sealed gallon packing complete all as specified and directed.

M&L for servicing of AMF panel of DG set of capacity upto to 75 KVA cleaning of AMF panel, rectification of defect rewiring, replacement of D/S indicator with new indicator of complete AMF panel and replacement of U/S relays under respective item of this schedule complete all as specified and directed.

All as peritem No 123 above but DG Set of capacity above 75 KVA and upto 200 KVA.

M&L for Replacement to unserviceable batteries of 12 volts 180 AH with new batteries of 12 volts 180 AH maintenance free complete all as specified and directed. Note: Rate for initial charging are included in unit rate

Supply & fix Automatic voltage regulator relay 415V AC complete all as specified and directed.

Supply & fix Electronic timer 240V AC, adjustment time 6-120 sec complete all as specified and directed.

Supply & fix reverse power relay, 415V AC complete all as specified and directed.

S&F PVC insulate copper heavy duty 1 mtr long as battery lead suitable for batteries of capacity 24V, 180AH complete all as specified and directed.

S&F in replacement of digital multi function meter to read voltage current and power factor including set of CT-1 each complete all as specified and directed.

S&F in replacement of indicating lamp RYB complete all as specified and directed.

S&F in replacement of Auto manual switch complete all as specified and directed.

S&F in replacement of push button switch red with element complete all as specified and directed.

S&F in replacement of push button switch green with element complete all as specified and directed.

S&F in replacement of 3 pole power contactor LT MNX 95 CONT complete all as specified and directed.

S&F in replacement of 3 pole power contactor LT MNX 140 CONT complete all as specified and directed.

S&F in replacement of 3 pole power contactor LT MNX 225 CONT complete all as specified and directed.

S&F in replacement of Autocut Electrical Battery Charger 12V DC, 5 Amp Unit SMPS with Constant Voltage Output with Battery Charging Transformer and Moulded Type Rectifier Unit etc complete all as specified and directed.

All as per item No 138 above but Battery Charger 24V DC, 10 Amp complete all as specified and directed.

M&L for Chemical earthing, Design development supply commissioning and testing EHCC certified ground terminal earthing system hollow tube solid bar CPRI tested for sensitive signal/Electrical equipments highly anti-corrosive long life severe wear conditions in the earth pit and of standard size ISI marked copper tube outside secondary conductor of 50mm dia and main primary conductor inside 25mm dia 3000 mm length ready to install with suitable connecting terminal conforming to IS:3043 1987 specification highly conducive packing material to be filled in earth pits for providing uniform low resistivity anti-corrosive hygroscopic medium around the earth system for improving the efficiency of current dissipation 20 Kg per bag (3 bag per kit) min or sufficient quantities required as per site complete including PCC pits of inside dimension 0.5x0.5x0.5m and suitable cover complete all as specified and directed. Note: (i) Rate of Earth work, Earthing electrode, all connections, nut-bolts, washers, complete labour, testing, Earth lead/strip upto 7.5 mtr, char coal dust, common salt, porcelain insulator,PCC earth Pit, CI frame ,RCC cover, funnel with wire mesh are incl in quoted rate and watering pipe, earth lead protection pipe, test poit, and earth lead exceeding 7.5 mtr are measured and paid separately.

M&L for Providing PCC 1:3:6 type C-1 using 20 mm graded stone aggregate for damaged earth pit chamber with fair finish internal surface of concrete chamber of earth complete all as specified and directed.

S&F in replacement of 80 mm thick PCC pit cover of size 320 mm x 320 mm of PCC 1:2:4 type B-1 using 20 mm graded stone aggregate, including necesssary reinforcement, formwork and handle for removing the cover from pit with fair finish, complete all as specified and directed..

S&F in replacement of Ceramic insulator of standard size for ligthning strip protection fixed in wall of one mtr distance with suitable size screws complete all as specified and directed..

S&F in replacement copper strip 20 x 3.0 mm fixed with top of insulator/saddles, fixing with screws , washer etc with help of drill machine for roof conductors and down conductors above ground and and making good disturbed surfaces of walls, floors, etc complete all as specified and directed..

S&F in replacement for Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm, drilled and screwed including 3 nos. 8mm dia 25mm long hexagon head screw complete all as specified and directed..

M&L for preparing surfaces of DG set of capacity up to 200 KVA by rubbing old paint and applying two coats of spray painting with (existing colour) deco paint from outside, complete all as specified and directed.. Note. (i) Painting of DG will be carried out for plinth mounted DG set . Necessary tools and plants shall be arranged by the contractor. (ii) MES No / SM No has to be written with 3" letters on each DG set after painting with white colour on black background without any extra cost.

PARAS ENTERPRISES (BID ID -3378467)

M/S Anand Enterprises (BID ID -3373043)

M/S Parshant Associates (BID ID -3378643)

High Tech Metal India (BID ID -3367351)

Singh Associates (BID ID -3377060)