PROVN OF GENDER SPECIFIC TOILETS AT VARIOUS PLACES AND SPECIAL REPAIR/REPLACEMENT TO PLUMBING AND SANITARY WORKS IN DOMESTIC AND TECHNICAL AREA AT AFS PURNEA UNDER AGE (I) (AF) PURNEA

Amount

Excavation in trenches, n.exc. 1.5 m wide and n.exc. 1.5 m in depth, for foundation etc, or manholes etc and getting out in soft/loose soil

Returning filling in including spreading levelling watering and well ramming inlayers n.exc. 25 cm in soil.

Removing excavated material spoil exc. 50 m n.exc. 100 m and deopoting where directed at a level n.exc. 1.5 m above starting point.

M&L Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 (using brunt brick)

M & L Cement concrete in foundations, filling and mass concrete Type D2 1:4:8 (40 mm graded aggregate)

M&L plain cement concrete in benchign (surface channels and drains) type B2 1:2:4 (40 mm graded stone aggregate).

M&L plain cement concrete type B1 1:2:4 (ung 20 mm graded stone aggregate) in coping, incl weathering, slighntly rounded or chamferred angle and throating, as directed.

M&L rendering cement plaster 1:4 , 15 mm thick on fair faces of brick work or concrete surfaces finshed even and smooth without ung extra cement.

M&L Extra for fomring fair finished rain on channel 30 cm inner girth in cement concrete ung extrta cement including form and mounds mitred/stopped ends.

M&L Providing pre cast cement concrete type B1 1:2:4 (20 mm graded aggregate) in manhole cover slabs set tin cement mortar 1:6.

S&F Sail-glazed stoneware drain pipes laid in trenches and jointed as specified.150mm dia

M & L concrete bed, type C-2, 1:3:6 for drain pipes including packing under and haunching against the des of pipes after they are laid and tested.

S & F 100 mm dia cast iron (sand cast pipe) soil, west, vent pipes of any length with or without ears with cement joints fixed to walls.

S & F cast iron cowl 100 mm dia.

S & F bands straps, supports or stays for rainwater ventilating pipes incl bolts, if required hooks, heavy for large gates hook and pintle hinges large hasps and staples chains, hand made sling bolst, clamps; hold fasts, handles; wall ties, hooks for hanging fans plain angle cleats for securing purlins to wood trusses or rafters knee piece inserts two way and three way straps, plate washers and milar small articles conforming to Fe 290, Gde E-165.

Surface dressing n.exc (not exceeding) 15 cm deep in soft /Loose soil.

M&L Cutting out concrete blocks, slabs, brickwork or stone masonry (in alter nate course), forming tooth-ings for and bonding new work in mortar into old work, including new materials entering old wall built in cement mortar 1:6

M&L RCC 1:2:4 type B-1 using 20mm graded aggr as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surface of concrete flat

M&L PCC 1:2:4 type B-0 in Damp proof course to horizontal or vertical surfaces including necessary formwork

M&L Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M & L cement concrete type C1 1:3:6 75 mm thick as in plinth protection

M & L Cement concrete 1:4:8 ,Type D2 75 mm thick ( 40 mm graded aggregate) as in sub base

M & L Cement concrete Type B0 25 mm thick 1:2:4 ( 12.5 mm graded aggregate as in sub base

M & L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering

M & L Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes CM 1:6

M&L Rendering 10mm thick in Cm 1:4 on fair faces of brick work or concrete surfaces as in backing coat for receiving the tiles.

M & L Glazed ceramic tiles in vertical surface 450x300x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match (coloured tiles)

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 Sqm but exc 0.11 sqm and nexc 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match.

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet .50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified ( for ridge only)

S & F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates (Fe-410- W(Gde- E-250) quality- B

Material & Labour for aluminium anodized snap grid frame work for false ceiling, grid size 605 x 605mm, using standard anodized aluminium 'T' section of size 45mm x25mms1.5mm thick and 45mmx25mmx1.5mm thick angle sections, etc complete all as specified & directed.

S& F Hangers 2.25mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

S& F non asbestos fibre cement building boards (E boards of size 600x600mm) decorative type fixed or laid/ inserted to timber/GI/Aluminium framework with screws as in ceiling .5mm thick.

M&L for rendering 15 mm thick in fair face of brick work or concrete surface in CM 1:6 finish even and smooth without using extra cement .

M&L for rendering 20 mm thick in other than fair face CM 1:4 finish even and smooth without using extra cement in two coats using WPC.Note WPC shall be measured and paid seperatly under relevent item.

Supply only integral waterproofing compound

M&l for preparation of newly plaster surface of wall and applying two coat of oil bound destemper over a coat of alkali resistant primer and one coat of wall putty as specified

M&l for preparation of newly plaster surface of wall and applying two coat of cement paint over a coat ofchalk whitening primer and one coat of wall putty as specified

M & L PCC 1:3:6 Type C1 using 20 mm graded aggrege for receiving of holdfast

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

S&F 100mm long stainless steel butt hinges all as specified

S&F 75mm long stainless steel butt hinges all as specified

S & F Aluminium anodised, barrel tower bolts of extruded section and fixed (150 mm )

S&F Extruded aluminium alloy handles, fabricated type, anodise 150 mm long

S & F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed ( 300mm long)

M&L two coat of synthetic enemal paint over acoat of red oxide primer Surfaces of any steel or iron description, over 10cm in width or girth,not otherwise described

S & F Steel windows or ventilators, fixed type, with glazing bars

S&F flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165

S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers

S&Fstainless steel mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples

S&F Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane

M&LRCC 1:2:4 type b-1 20 mm graded aggr as in chajja Slabs shelves and the like

M&L Formwork to chullah hoods, chajjas, troughs and similar items including edges

M & L PCC 1:3:6 Type C1 ( 20 mm graded aggregate ) as in coping/Bed plate

M & L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M & L TMT bars 08 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips in stirrups, spacers and binders

S & F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified ( 1000 Ltrs capacity)

S & F Vitreous China wash basin, white, flat back, size 550X400mm excluding ditto but including brackets

S&F Vitreous China, semi-pedestal pattern (Anglo-Indian Type) (ditto) (excluding flushing cistern and flush pipe),

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, 15 mm dia

S&F CP towel rail 600mm long incl all fittings

S&F sheet glass shelf assembely consisting of 5.5 mm tk sheet glass shelf 12mm wide with cp brass bracket guard 60cm long complete as specified.

S&F Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors ,15 mm bore

S&F Tubes,medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors ,20 mm bore

S&F Tubes, medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors ,25 mm bore

S&F stainless steel grating 100 mm dia over floor trap complete all as specified

M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough rinished surface of concrete flat.

M&LRCC 1:2:4 type B-1 20mm graded aggr as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls (soil waste and vent pipes) 110 mm dia

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls (soil waste and vent pipes) 75 mm dia

S&F PVC (SWR) bends any radius suitable for 75 mm bore pipe provided with acces door complete

S&F PVC (SWR) vent cowl ,110mm

Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound ,Gde -B.(plinth protection)

S & F PVC SWR Nahni trap 110 mm dia

M&L preparing newly plastered surface and Three coat of white wash on ceiling surface complete

M&L Rendering 5 mm thick in CM 1:3 on fair faces of eiling surfaces complete.

S & F flat iron of the 25 x 3 mm for hold fasts conforming to Fe-410 e.

M&L for Treating small articles such as holdfast with coal tar

S&F brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed 20 mm dia

S&F in repair CP fancy type towel rod 18/20mm dia, 600mm long including brass screws and wooden/ plastic cleates of approved make. All as per specified and directed by Engr incharge. (Make : Prayag Cat No. BA-20 or equivalent).

Cutting chase in brick wall for concealed water tubing or similar work etc and making good, cutting not exc 10cm girth.

Dismantaling floor, hearth or wall tiling including cement mortar bedding(but not backing) removing servicable tiles to store and rubbish off premises.

M&L rendering 15 mm thick in CM 1:6 on wall to receive tile.

M&L for screed bed or bedding 15mm thick in CM 1:6 on floor to receive tile.

S & F Non Skid Ceramic Colour Tiles 7 to 8 mm thick area of each tiles exc 0.06 Sqm but n. exc 0.11 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match. (Make - Somany, kajaria, Johnson.)

M& L glazed cermic coloured tile in vertical surfaces 300x450x7 mm thick set and joited in neat cement slurry and poited in white or coloured cement to match (Make - Somany, kajaria, Johnson.).

Taking up or down steel tubing and connections including cleaning for re fixing bore of pipe 15 mm.

Taking up or down steel tubing and connections including cleaning for re fixing bore of pipe 20 mm

Taking up or down steel tubing and connections including cleaning for re fixing bore of pipe 25 mm

Supply & laying of CPVC 16 mm outer dia pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed by Engr-in-Charge.

Supply & laying of CPVC 20 mm outer dia pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed by Engr-in-Charge.

Supply & laying of CPVC 25 mm outer dia pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed by Engr-in-Charge.

S&F 20mm Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed in repairs, complete all as specified and directed.(Approved make)

S&F25mm Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed repairs, complete all as specified.

S & F in repair vitreous china squating pan orissa pattern size 580x440 mm white with integral foot rests(excluding flushing cistern and flush pipe ,connecting to trap and flushing pipe. (Make : Prayag/Hindware/Jaguar

S& fixed in repair Vitreous china wash down watercloset pan (pedestal pattern) white (excluding fixing bolts,flushing cistern Including plastic seat cover, flat bottom and CP hinging device ), complete all as specified and directed. (Make : Prayag/Hindware/Jaguar

S & F PVC value less symphonic action type duo flushing cistern low level white with inlet ball value float and handle including brackets 10 liter capacity, fixed in repairs. (Make : Prayag (Cat No. 502)/Hindware/Jaguar

S&F in repair Vitreous china wash hand basin white flat back size 550x 400 including bracket with PVC waste pipe 32mm dia suitable length and waste fitting 32mm dia brass , chromium plated etc with long sunk and fly nuts , flange and bedded in red lead cement and othrer end complete all as specified . make - Parryware (Make : Prayag(Cat No. Hazel-4644)/Hindware/Jaguar

S & F 15 mm bore PVC connection with PTMT nuts of length 450 mm.

S&F 110mm PVC (SWR) branch piece single (single Y)equal or unequal with access door

S&F 110mm PVC (SWR) junction single(single T) equal or unequal with access door

S & Fixed in repair CP bib taps long body15mm dia, cast copper alloy with crotch or butterfly handle. Fancy type. (Make : Prayag(Cat No. 9208) /Hindware/Jaguar or equivalent or approved make).

S & Fixed CP Stop valve/ stop cock /angle cock fancy type 15mm dia cast copper alloy with long shank and cup (concealed type) (Make : Prayag/Hindware/Jaguar or equivalent or approved make).

M&L CP pillar tap but fancy type with long shank and up 15mm dia (cast copper alloy with crotch or butterfly handle Cat No. 29204 (Make : Prayag/Hindware/Jaguar

M&L waste filtting ,brass chromium plated for 32mm dia glazed ware sink , basin, urinal etc .with long screwed shanks and fly nuts flazed ends bedded in red lead cement and other end fixed

M&L waste filtting ,brass chromium plated for 32mm dia glazed ware sink , basin, urinal etc .with long screwed shanks and fly nuts flazed ends bedded in red lead cement and other end fixed (Approved make) bit fixed in repair

S&F PVC (SWR) floor trap with grating including jointing with solvent cement with outlet of 75mm

S&F PVC waste pipe for WHB 32mm dia

Demolition of cement concrete reinforced not exc 15 cm thick below or above ground level.

S&F in repair PVC waste pipe for urinal/kitchen sink 38/40mm dia

S&F in repairs Vitreous China Urinal, Half stall type, white (size 345x320x560mm), with PTMT spreder fixed in repair, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal including flush pipe, grating and Union for discharge pipe.( Make -parryware cat No -C0575 , White, Prayag Cat No. 4998

S&F PVC bathroom mirror 600x450mm, (Make : Prayag (Cat No. 4998

S&F in repair CP 2 in 1 Fauset (crome plated Faucet) with 1 mtr Tube and Hook , (Make : Prayag (Cat No. BEA-85

M&L concrete bed in cement concrete 1:4:8 type D-2 to drain pipes (75/100 mm dia) including packing under and completely surrounding pipes with concrete after they are laid and tested in.

M&L for cement concrete type B-1, 1:2:4 (20 mm graded aggregate) 25 mm thick as in floor

Taking down shutter of any description exc 1 Sqm n. exc 2 Sqm and easing, adjusting and refixing in the same opening

Taking down chowkats with shutter exc 1 Sqm but n. exc 2 Sqm (without taking of shutters from the frames.

S&F factory made PVC solid door frame (Chowkats) of size 50mmX47mm made out of 5mm plane colour PVC sheet in force with M.S. square tube supplying & fixing in opering as per specification & drawing.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame (with hinges/any fixing arrangement) at site as per specification & drawing.

S&F aluminium anodysed barrel towel bolts of extruded section and fixed 150 mm long

S&F 250 mm long alumimium alloid anodysed sliding door bolts with hasp and staple of alumimium extruded section.

S & F aluminium alloy handle 125 mm fabricated type

S & F in repair Gully round trap 4" (Cat No. F- 70m of make : Prayag or equivalent)

S&F in repair Gully round trap 4" with hole (Cat No. FP-63m of make : Prayag

S & F in wall mixture CP brass 3-in-1 provision for OHS and head shower , Cat No. 7780 Prayag)

S & F CP Brass towel ring (Cat No. BA-21 of make : Prayag

S & F towel rack (Cat No. BA-22 of make : Prayag

S & F full glass shelf 500 mm (Cat No. BEA-51 of make : Prayag

S & F full corner glass (Cat No. BEA-52 of make : Prayag

S & F soap dish with glass (Cat No. DA-25A of make : Prayag

S & F in repair dia 4" over head shower with 225 mm with flage (Cat No. DA-25A of make : Prayag

S & F white colour closet with integrated cistern seat cover and twin flash fittings complete of (Make : Pragag model Aquifer, 4360, 4260, 4460

M&L for concealed point wiring with 1.5 sqmm size single core multi standed copper conductor unsheathed PVC insualted 1100 V grade FRLS cable drawn into and including PVC conduit with accessories and fitting like bend elebows, crosses, wall crossing etc for one light / point controlled by one switch including shunken type pressed steel box width 3 mm thick plastic laminated sheet top cover of approved make for housing switchs, socket outlet and regulators etc and with continuous 1 No cable 1.5 sqmm copper conductor PVC insualted , unsheathed as earth wire connected to earth dolly and to be conncted boxes of suitable sizes for mounting to fitting etc,make good surface complete all as specified and as directed.

All as per item No 137 here-in -before but 1.5 sqmm copper conductor for 3 pin 5 Amps socket outlet independent (Multiple) controlled by one switch with one No earth continuity copper conductor of size 1.5 sqmm complete all as specified and as directed.

All as per item No 137 here-in -before but 4 sqmm copper conductor for 3 pin 15 Amps socket outler independent (Multiple) controlled by one switch with one No earth continuity copper conductor of size 4 sqmm. complete all as specified and as directed.

M&L switch socket combination 2 in 1 , 5 Amps multipurpose , flush type complete all as directed.

M&L switch socket combination 2 in 1 , 3 pin ,5 and 15 Amps multipurpose , flush type complete all as directed.

M&L for switch piano, flush type single pole one way 5 amps complete all as directed by Engr - in - charge.

M&L ceiling rose, 3 terminal, single phase / PVC /polycarbonate isolated body. all as directed by Engr-in-charge

S&F sheet metal enclosures Double door DB-8 way, SPN, 200 Amps Bus bar 240 Volts complete all as directed by engr-in-charge.

M&L Isolater/MCB SPN 240 volt,40 Amps,complete all as directed.

M&L MCB SP 240 volt, upto 40 Amps,,complete all as directed.

M & L for submain concelled PVC conduit wiring with 2 run of single core FRLS , 4 Sqmm ( Nominal area ) and with one run of 4 Sqmm cable , PVC insulated , unsheathed,multistanded coopper conductor cable ,1100 Volts grade drawn through and including PVC non-metaliccasing caping of suitable size , medium grade ( ISI marked ) with all fittings and fixing accessories on roof, wall , ceilings etc complete all as specified and directed . ( Note : three run of 4 Sqmm cable and one run of PVC conduit in wall/ceiling be measured as one length.)

M&L PVC blocks suitable for fixing of tube light fitting on wall/ceiling complete all as directed by Engr-in-Charge.

S&F in replacement of tube light fitting 1x20 Watt, LED 230 V integrated Batten T-5 indoor decorative aluminium extended , energy efficient including t including tube Rode 20 Watt, comlete fixing on wall/ceiling ,& internally prewired , all as specified & directed by Engr-in-charge .

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver

M&L mini miror light fitting with lamp, 1x11watts LED wall/surface mounted luminaire engineering plastic housing, wired with all accessories and ballest complete all as directed. Note:-The contract sum shall be arrieved at after deducting amount of schedule of credit from the total quated amount.

M/s. Mohan Enterprise

M/s. S. Chandra Enterprises