REPAIR TO DRAIN CULVERT COMPOUND WALL FENCING AND GATES IN ZONE AREA UNDER AGE BR I OF GE EAST JABALPUR

Amount

Demolition of cement concrete in ground floors and paving not exceeding 15 cm thickness (Below or above ground level) and removing rubbish to a distance nexc 100m and depositing at low lying area complete all as specified and directed.

Taking down cement plaster and raking out joints, hacking for key, scrubbing down with water built in cement mortar.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches etc complete.

Excavation in trenches n exc 1.5 mtr wide and n exc 1.5mtr in depth for foundation etc, nexc 10 sqm on plan & getting out as in hard/dense soil all as specified and directed.

M&L for cement concrete 1:4:8, type D2 using 40mm graded stone aggregate in foundations, filling and mass concrete.

M&L brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM 1:6 all as specified and directed.

Same as per Item Srl No 6 above but except bricks

M&L for reinforced cement concrete (design mix) M-20 (using 20mm graded stone aggregate) as in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

M&L rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 rendering is to be finished even and smooth without using extra lime or cement all as specified and directed.

M&L for formwork to rough finishes faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter.

M&L for 75mm bore UPVC Pipes (SCH-40) laid in weep holes complete all as specified & directed.

Returning filling in including, spreading, levelling watering and well ramming in layers n. exc 25 cm thick complete all as specified and directed.

Removal of surplus soil to a distance n. exc 50 mtr from the starting point and at level of 1.5 mtr complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specifiedof RCC jali of any description.

M&L 15mm thick rendering in CM 1:4 on of brick or concrete surface finished even and fair on walls without using extra cement complete all as specified and directed.

M&L for providing precast cement concrete type B-0 (1:2:4) (12.5mm graded aggregate) as in louvers and jallies, 35mm thick (measured solid) set CM 1:4, including all mouldings but excluding frame.

M&L PCC (1:2:4) type B-1 (20mm graded aggregate) as in kerbs/coping and the like including weathering, slightly rounded or chamfered angles and throating, including formwork complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in surface channels and drains complete all as specified and directed.

M&L for extra for forming fair finished drain or channel not exc 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

M & L for providing precast cement concrete 1:2:4 type B-1 using 20 mm stone aggregate as in cover slabs (any type) and similar work round square or rectangular in shape and set in CM 1:4 complete all as specified and directed. Note : All RCC manhole covers to be embossed with Month & year of casting.

M&L TMT bars 8mm dia, cut to length bent to shape required including cranking, bending spirally for hoping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia quality confirming to Fe 410-5 or Fe 400-0.

All as per Item Srl No 21 above but 10mm dia over.

M & L preparing plastered/ unplastered new surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

Dismantling posts or struts (Wood, steel or RCC) any section including taking out embedded portion and making good disturbed ground in natural ground.

Excavating in post holes or single holes each n. exc 0.5 cum getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers n. exc. 25 cm watering and removing surplus soil to a distance n. exc 50 m and making good surface of hard/ dense soil.

M&L rolled mild steel in post and struts in fencing including tops to shape as directed drilling holes notching for wire, etc flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting or riveting etc and similar work conforming to Fe 290 Gde E 165.

M & L cement concrete type C2 1:3:6 (40 mm graded stone Aggregate) as in embedding of precast post in foundation filling and mass concrete complete all as specified and directed.

Dismantling of fencing wire mesh any type complete all as specified and directed.

Supply only chain link fencing MS galvanized of wt not exceeding 4.00 Kg/Sqm complete all as specified and directed.

Fixing only chain link fencing incl line wires of size 50/75x100mm to any type of standards, rails, straining bolts (weight of chain link fencing should be of not exceeding 4.00 Kg/Sqm) complete all as specified and directed.

S&F in repairs Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed each line wire to be measured) complete all as specified and directed.

M&L mild steel bolt machine made with hexagonal or square beads at one end and screwed the other or screwed both ends each screwed and to be fitted with washers and one hexagone or square but length of bolt exc 5 cms but not exceeding 10cm long dia shall be of 5 to 10mm dia complete all as specified and directed.

M&L Mild steel round bars 10 mm dia and over, cut to length, bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (Annealed) not less than 0.9 mm dia all as specified confirming to Gde E 250 or Gde E 165 complete all as specified and directed.

M&L new or previously untreated two coats of synthetic enamel painting over one coat of red oxide on steel and iron surfaces incl necessary preparation of surfaces complete all as specified and directed.

M& L new or previously untreated for painting to steel and iron surfaces of any description, over 10 cm width or girth, not otherwise described with two coats of black bituminous paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

Taking down 100 mm bore rain water pipe, soil waste pipe any size including all fittings all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed in any length including with rubber ring bends, 'Y' junction etc fixed to walls/floor with clamps, holdfasts etc including cutting holes in walls and making good with PCC 1:2:4 complete all as directed. Joints fixed with as per manufacturer direction.

All as per Srl Item No 37 here in above but 75mm dia .

S&F in repair 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F in repair 110 mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repair 75 mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

M&L in repair PVC (SWR) gully/nahani trap 75/110/125 mm, including with CP grating, setting and jointing with solvent cement complete all as specified and directed.

S&F in repair 110mm PVC (SWR) WC connector with lip ring complete all as specified and directed.

All as per Srl Item No 44 here in above but bent type complete all as specified and directed.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; square bars as in cupboards, wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

Supplying and laying of PVC pipe bearing ISI mark of IS-15328 150 mm dia minimum 4 mm thick incl jointing with coppler complete laid in trenches or floors complete all as specified and directed Make : Supreme/Kisan/Finolex.

All as per Srl Item No 47 here in above but 200mm dia complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, incl nanital or similar pattern roof covering complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.5mm thick of any colour (Profiled pattern and joints/lapping filled with silicon compound) any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws. (Make :Tata(duroshine)/Cril/ JSW). including necessary cutting groves chasing to wall and making good with PCC 1:2:4 (20mm graded stone aggregate) & plaster in CM (1:3) complete all as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.60mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, in ridges, hips, valley gutters, drip and straight flashings etc.fixed with self tapping screws as specified. (Make : Tata (duroshine) / Cril / JSW) complete all as directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

S&F for mild steel rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410 -W (Gde- E- 250) quality- A including necessary welding complete all as specified.

S&F mild steel flat iron as in wind tie for roof including cutting & making holes for securing bolts, confirming to Fe 410-W (Gde-E-250) quality-A complete all as specified and directed.

Schedule of credit amount of Rs. 2,02,777.50 to be deducted during AOC

ISHWAR CONSTRUCTION COMPANY

M/S BHATIA CONSTRUCTIONS

M/S BHARTI ENTERPRISES

M/s Kehar Engineers

M/s Ram Associates

LAL SINGH & SONS

SR ASSOCIATES

M/S Modern builders