C/o. CO Office and other residential quarters at Sibe Circle, Lower Siang District

Amount

1. SH:- CO Office

Building Portion

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Providing and laying in foundations and plinth cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size).

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring an shuttering in:

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.

Centring and shuttering including strutting, propping etc and removal of form work for :

a) Column, pillars, posts and struts etc.

b) Lintels, beams, girders, bressumers and cantilevers etc.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

Providing and fixing flush door shutters, decorative type, core of black board construction with frame of 1st class hard wood and well matched 1st class teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

b) Ornamental grill.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing iron pressed butt hinges bright finished with necessary screws etc complete.

a) 100 x 50 x 1.90 mm

b) 75 x 47 x 1.70 mm

Providing and fixing MS sliding door bolts, bright finished or and black enamelled with nuts and screws etc complete.

Providing and fixing MS tower bolts (barrel type) with necessary screws etc complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete b) Size of Tile 600x600 mm

Providing and laying vitrified tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3, including grouting the joint with white cement & matching pigments etc. complete a) Size of Tile 500x500 mm

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses.

b) 0.63 mm thick GI sheet

Providing ridges or hips 60 cm overall in plain G.I. sheet fixed with galvanised iron J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete.

b) 0.63 mm thick GI sheet

Providing and fixing 20 mm thick wooden planks ceiling (frame work for base to be paid separately) with M.S. screws.

a) Timber Plank Class - A IV

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.

a) Best local approved quality wood.

12 mm cement plaster 1 : 6 (1 cement : 6 fine sand).

15 mm cement plaster 1 : 6 (1 cement : 6 fine sand) on the rough side of single or half brick wall.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Providing and fixing local wooden railing 0.75 m high with 7.5 x 5 cm top and bottom rails 7.5 x 5 cm sides and 5 cm x 5 cm intermediate vertical bars placed at 22.5 cm centre to centre including painting two or more coats as directed.

Neat Cement Punning

Reinforcement of RCC work including bending, binding and placing in position complete.

a) Cold twisted bars.

Providing two coats of acrylic water based wall putyy/wall filler of Asian Paints/Berger/Dulux over concrete/cement plaster/brick walls and ceiling both internal and external after removing all the loosely adhering material from the wall/ceiling surface with the help of emery stone,putty blade or wire brush, moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department.

White washing with lime on new work (two or more coats) to give an even shade.

Wall painting (two or coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

SANITARY ITEM

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

a) Long Pan patten WC Pan

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.

a) Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality.

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.

a) 250 x 130 x 30 mm

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.

a) 100 mm dia SW pipes

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design.

a) 100 mm dia SW pipes

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design.

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).

a) 15 mm nominal bore

Providing and fixing brass bib cock of approved quality.

a)15 mm nominal bore

Providing and fixing brass stop cock of approved quality.

a) 15 mm nominal bore

Providing and fixing PVC connection pipe with brass union. A) 30 cm Length

a) 15 mm nominal bore

Furniture

Secretariat Table

Revolving Chair

Visitor's Chair

Godraj Almirah

Office Wooden Table with Drawer

Wooden Arm Chair

Computer Table & Chair

Wooden Rake

Site Development

Excavation in ordinary rock by manual means (Excavation in ordinay rock using manula means including loading in a truck and carrying of excavated material to embarkment site with in all lifts and leads upto 1000 metres

2. SH: Type IV Quarter

Building Portion

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surples excavated soil as directed within a lead of 50 m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4graded stone aggregate 20 mm nominal size.)

Applying a coat of hot bitumen (mashphalte 80/100 or equivalent) using 1.70 Kg per Sq.m. on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Centring and shuttering including strutting, propping etc and removal of form work for :

a) Foundation, footings, bases of columns etc. and mass concrete.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

e) Column, pillars, posts and struts etc.

d) Lintels, beams, girders, bressumers and cantilevers etc.

g)Vertical and horizontal fins individually or forming box louvers bands and facias.

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in :

a) M20(1.5 cement : 3 coarse sand & stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.

a) M20(1.5 cement : 3 coarse sand & stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface

a) M20(1.5 cement : 3 coarse sand & stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement with M20 (1 cement: 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with M20( 1.5 cement: 3 coarse sand & stone aggregate 20 mm nominal size).

Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers bands and facias up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding the cost of centering, shuttering and reinforcement with M20 (1 cement : 1.5 fine sand : 3 stone aggregate 12.5 mm nominal size)

Reinforcement of RCC work including bending, binding and placing in position complete.

a) Cold twisted bars.

b) Mild Steel Bars

Brick work with best available local bricks in foundation and plinth in cement mortar 1:4 (1 cement : 4 fine sand).

Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.

Half brick masonry (with best available local bricks) in cement mortar 1:3 (1 cement : 3 coarse sand) in foundation and plinth.

Extra for half brick masonry in superstructure above plinth level and up to floor two level.

Providing hoop iron 25 mm x 1.60 mm or equivalent reinforcement in brick masonry at every fourth course, embedded in cement mortar.

WOOD WORKS

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws.

a) 38mm thick best available local wood class - B I

Providing and fixing best available local wood glazed shutters for doors, windows and clerestory window using 7.5 kg/Sq.m. (3 mm thick glass panes) including black enamelled MS butt hinges with necessary screws.

a) 35 mm thick

Providing and fixing 38 mm thick wire gauge shutters using galvanized mild steel wire gauge of IS gauge designation 140G with wire of dia 0.56 mm for doors, windows and clerestory windows including anodized aluminum butt hinges with necessary screws.

a) Best available local wood

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

b) Ornamental grill.

Providing and fixing MS Hooks and Eyes.

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

STEEL WORK

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).

Steel work in single section including cutting, hoisting, fixing in position and applying a priming coat of red lead paint.

c) In Flats up to 10 mm in thickness

Providing and fixing MS round holding down bolts with nuts and washer plates etc complete.

Providing and fixing bolts up to 300 mm in length including nuts and washers complete.

Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during lying including painting the exposed portion of loop all as per standard design complete.

FLOORING

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete

a) Size of Tile 500x500 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

a) Size of Tile 500x500 mm

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement.

b)75 mm thick

Roofing

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses.

a) 0.80 mm thick GI sheet

Providing ridges or hips 60 cm overall in plain G.I. sheet fixed with galvanised iron J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete.

a) 0.80 mm thick GI sheet

Extra for providing and fixing wind ties of 40 x 6 mm flat iron section.

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc complete (Frame work to be paid separetly)

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.

a) Best local approved quality wood.

Extra for making chamfered edges of beading.

FINISHING

15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall.

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall.

Neat cement punning.

Painting two coats with oil type wood preservative of approved brand and manufacture on new work.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Applying priming coat with ready mixed primer of approved brand and manufacture on steel work.

Painting two or more coats on Steel works with ready mixed superior paint of approved brand and manufacture on new work to give an even shade.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Applying one coat of distemper primer of approved brand and manufacture on wall surface.

Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.

White washing with whiting on new work (three or more coats) to give even shade.

painting two or more coats on GI sheets with ready mixed superior paint of approved brand and manufacture on new work to give an even shade.

MISCELLANEOUS

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

DRAINAGE

Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar 1:3 (1 cement : 3 fine sand) including shuttering complete

SANITARY

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

a) Long Pan patten WC Pan

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.

a) 250 x 130 x 30 mm

Providing and fixing 100 mm sand cast iron grating for gulley, floors or nahni trap.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality).

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

a) 100 mm dia

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design.

a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).

Construction of soak pit 2.5 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mm dia and 1.80 m long complete as per standard design.

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.

a) Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality.

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

WATER SUPPLY

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).

b) 20 mm nominal bore

Providing and fixing brass bib cock of approved quality.

a)15 mm nominal bore

Providing and fixing brass stop cock of approved quality.

a) 15 mm nominal bore

Site Development

Excavation in ordinary rock by manual means (Excavation in ordinay rock using manula means including loading in a truck and carrying of excavated material to embarkment site with in all lifts and leads upto 1000 metres

3. SH: Type-II Quarter

Building Portion

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Providing and laying in foundations and plinth cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size).

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring an shuttering in:

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.

Centring and shuttering including strutting, propping etc and removal of form work for :

a) Column, pillars, posts and struts etc.

b) Lintels, beams, girders, bressumers and cantilevers etc.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

Providing and fixing flush door shutters, decorative type, core of black board construction with frame of 1st class hard wood and well matched 1st class teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

b) Ornamental grill.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

2.5 cm Nosing in steps in 1:3 cement mortar

Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge

Providing and fixing MS sliding door bolts, bright finished or and black enamelled with nuts and screws etc complete.

Providing and fixing MS tower bolts (barrel type) with necessary screws etc complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete b) Size of Tile 600x600 mm

Providing and laying vitrified tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3, including grouting the joint with white cement & matching pigments etc. complete a) Size of Tile 500x500 mm

12 mm cement plaster 1 : 6 (1 cement : 6 fine sand).

15 mm cement plaster 1 : 6 (1 cement : 6 fine sand) on the rough side of single or half brick wall.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Neat Cement Punning

Reinforcement of RCC work including bending, binding and placing in position complete.

a) Cold twisted bars.

Providing two coats of acrylic water based wall putyy/wall filler of Asian Paints/Berger/Dulux over concrete/cement plaster/brick walls and ceiling both internal and external after removing all the loosely adhering material from the wall/ceiling surface with the help of emery stone,putty blade or wire brush, moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department.

White washing with lime on new work (two or more coats) to give an even shade.

Wall painting (two or coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

SANITARY ITEM

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

a) Long Pan patten WC Pan

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.

a) Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality.

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.

a) 250 x 130 x 30 mm

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.

a) 100 mm dia SW pipes

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design.

a) 100 mm dia SW pipes

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design.

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).

a) 15 mm nominal bore

Providing and fixing brass bib cock of approved quality.

a)15 mm nominal bore

Providing and fixing brass stop cock of approved quality.

a) 15 mm nominal bore

Providing and fixing PVC connection pipe with brass union.

A) 30 cm length

a) 15 mm nominal bore

Site Development

Excavation in ordinary rock by manual means (Excavation in ordinay rock using manula means including loading in a truck and carrying of excavated material to embarkment site with in all lifts and leads upto 1000 metres

4. SH-Bachelor Barrack

Building Portion

Earth work in excavation in soils containing 50% or more of shingle or small size boulders upto 30 cm size including banking in 20 cm layers and breaking clods, ramming and dressing up for the purpose of making embankments or filling up ground depressions lead upto 50 m and lift upto 1.50 m.

Providing and laying in foundations and plinth cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Reinforcement in RCC work including bending, binding and placing in position etc complete. b) Cold twisted bars

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in :

M20 (1 Cement : 1.5 coarse sand :3 Stone aggregate 20mm nominal size)

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand)exluding cost of centring, shuttering and reinforcement.

M20 (1 Cement : 1.5 coarse sand :3 Stone aggregate 20mm nominal size)

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 but excluding cost of centering, shuttering and reinforcement.

M20 (1 Cement : 1.5 coarse sand :3 Stone aggregate 20mm nominal size)

Centring and shuttring including strutting, proping etc. and removel of form work etc complete.

a) Foundation, footings, bases of columns etc. and mass concrete.

b) Column, pillars, posts and struts etc.

c) Lintels, beams, girders, bressumers and cantilevers etc.

Brick work with best available local bricks in foundation and plinth in cement mortar 1:3 (1 cement : 3 fine sand).

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing and laying in foundations and plinth cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

25 mm thick cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) finished with a floating coat of neat cement.

Half brick masonry (with best available local bricks) in cement mortar 1:3 (1 cement : 3 coarse sand) in foundation and plinth.

Extra for half brick masonary in superstructure above floor two level.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws. a) 38mm thick best available local wood class - B I

Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal size).

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws. Ornamental Grills

Providing and fixing MS sliding door bolts, bright finished or and black enamelled with nuts and screws etc complete.

Providing and fixing Iron T-hinges bright finished or and black enamelled with necessary screws etc complete.

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.

12 mm cement plaster 1 : 3 (1 cement : 3 fine sand).

Providing two coats of acrylic water based wall putyy/wall filler of Asian Paints/Berger/Dulux over concrete/cement plaster/brick walls and ceiling both internal and external after removing all the loosely adhering material from the wall/ceiling surface with the help of emery stone,putty blade or wire brush, moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department.

Distempering with dry distemper of approved brand and manufacture (two or more coats) and of required shade on new work including priming coat of whiting to give an even shade.

Appling priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses.

b) 0.63 mm thick GI sheet

Providing ridges or hips 60 cm overall in plain G.I. sheet fixed with galvanised iron J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete.

b) 0.63 mm thick GI sheet

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing 4.0 mm thick asbestors plain sheet ceiling of approved quality with necessary nails etc.complete (frame work for base to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.

a) Best local approved quality wood.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Providing and fixing brass bib cock of approved quality.

Providing and fixing brass stop cock of approved quality.

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mmwith specials and mosquito proof coupling and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors

a) Long Pan pattern WC Pan

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.

a) 250 x 130 x 30 mm

Providing and fixing 5 litres CI automatic flushing cistern with fittings.

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

a) 100 mm dia

Providing and fixing sand cast iron trap of self cleadnsing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors.

a) 100 mm inlet and 100 mm outlet

Making Septic tank

Earth work in excavation in soils containing 50% or more of shingles or small size boulder up to 30 cm size including banking in 20 cm layer and bracking clods, ramming and dressing up for the purpose of making embankments or filling up ground depression

Providing and laying cc 1:5:10 ( excluding the cost of centring and shuttering )

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding the cost of centering and shuttering and reinforcement with M20 (1:1.5:3 20mm aggregate nominal size)

Reinforcement of RCC work including bending, binding and placing in position complete. (Cold twisted bars)

CI cover with frame 300x300 mm inside

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes. ( 100 mm dia )

Providing and fixing on wall face asbestos cement soil, waste and vent pipes including jointing with spun yarn soaked in bitumen and cement mortar 1 : 2 (1 cement : 2 coarse sand) complete.

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Site Development

Excavation in ordinary rock by manual means (Excavation in ordinay rock using manula means including loading in a truck and carrying of excavated material to embarkment site with in all lifts and leads upto 1000 metres

DDL ENTERPRISES (BID ID -6830)