GE/KHU-41/2021-2022 PROVISION OF MT SHED AT HANUTHANG IN THE AOR OF AGE B/R-II KHALTSI, UNDER GE KHUMBATHANG

Amount

M&L for surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil complete all as specified and as directed by Engnr-in-charge.

M&L for excavating in post holes (or similar holes) each n exc 0.5 cu.m. , getting out , returning, filling, in and ramming earth or broken rubble mixed with earth around , in layers not exceeding 25 cms and getting out in Hard/dense soil complete all as specified and as directed by Engnr-in-charge.

M&L for excavating in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth for foundation, etc.,n exc 10 sq m on plan and n exc 1.5 m in depth and getting out and getting out in hard/dense soil complete all as specified and as directed by Engnr-in-charge.

Removing excavated material (Soil) n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed by Engnr-in-charge.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation complete all as specified and as directed by Engnr-in-charge.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in foundation and mass concrete complete all as specified and as directed by Engnr-in-charge.

S&F rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 tubes complete all as specified and as directed by Engnr-in-charge.

S&F rolled mild steel in flat iron, trussed , rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe410-W (Gde-E-250) quality-A complete all as specified and as directed by Engnr-in-charge.

S&F rolled mild steel in plates (plain or chequered) square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed by Engnr-in-charge.

S&F 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roof, walls etc with grade of zinc coating 275 complete all as specified and as directed by Engnr-in-charge.

M&L for preparation of newly or previously untreated surfaces of steel or iron work over 10 cms width or girth and applying two coats of synthetic enamal paint over a coat of red oxide, zinc chrome primer complete all as specified and as directed by Engnr-in-charge.

M & L for pre-cast cement concrete block masonry ( Type C-1 ,1:3:6 , 20 mm graded aggregates) with solid blocks exc. 10 cm in width and setting in mortar 1:6 , complete all as specified and as directed by Engnr-in-charge.

M&L for rendering 15mm thick cement plaster on fair faces of brick work on concrete surfaces in cm (1:4) rendering to be finished even and smooth without using extra cement complete all as specified and as directed by Engnr-in-charge.

M&L for preparation of newly plastered surface and applying two coats of cement paint over a coat of chalk whiting on walls complete all as specified and as directed by Engnr-in-charge.

M & L for 100mm thick cement concrete 1:4:8 type D-2 (40mm graded stone aggregate) as in sub base of flooring complete all as specified and as directed by Engnr-in-charge.

M & L for 100mm thick cement concrete 1:2:4 type B-1 (20mm graded stone aggregate) as in flooring finished even and smooth without using extra cement complete all as specified and as directed by Engnr-in-charge.

M & L for glass dividing strips, 3 mm thick and width of strip 28 mm, inserted in position, conform to design in floor, complete all as specified and as directed by Engnr-in-charge.

M/S HIGHLAND ENGINEERING

KASHMIR FAIR DEAL SERVICES

SONAM ANGCHOK