GE/BAS-82/2025-26 Provn of night picquet with bathroom and toilet and provn of LT underground cable at Janglote under GE Basoli

Amount

Excavation in trenches n exc 1.5 m wide and n.exc 1.5 m in depth for foundation of pole/stay and laying of UG cable/GI pipe and getting out in any type of soil complete all as specified and directed.

Excavation over area not exc 1.5m deep in any type of soil and getting out complete all as specified and directed.

M&L returning, filling and including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated material nexc 50m and depositing where directed at a level nexc 1.5mtr above the starting point , complete all as specified and directed.

Surface excavation not exc 30cm deep and averaging 15cm deep and gettingout in any type of soil complete all as specified and directed.

M&L Cement concrete M-7.5 (Nominal mix),type D-2, 1:4:8, (using 40 mm graded crushed stone aggregates) in foundation filling and mass concrete, post holes etc complete all as specified and directed.

M&L Reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases of columns etc basement slabs, under-reamed piles and mass concrete complete all as specified and directed

M&L Reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregates as in slabs, supported on walls, beam and columns in floors and in shelves and the like complete all as specified and directed.

M&L Reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregates as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L Reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregates as in beams, chajja, cantilevers, bressummers, lintels over 1.5 mtr span complete all as specified and directed.

Steel Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and sofits of foundation and plinth beams; and similar works; vertical or to batter for rough finished flat surfaces complete all as specified and directed.

Steel Form work to sides and soffits of floor/roof beam for rough finished flat surfaces of concrete complete all as specified and directed.

Steel Form work to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete complete all as specified and directed

Steel Form work to soffits of suspended slabs such as roof slabs, floor slabs etc not exceeding 200mm thick complete all as specified and directed.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

-ditto- here-in-before but 8mm dia and over upto and including 10mm dia as in stirrups, spacers, binders complete all as specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately).

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter decorative type, of 30 mm size comprising of virgin polymer of K value 58-60 ,calcium carbonate and natural fibre and non toxic additives minimum compressive strenth 50 N/ mm2, modulas of elasticity 850 n/ mm2 and resistance to spred of flame of Class A cateegory with property of being termite/borer proof ,water /moisture proof and fire retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approval design pasted with hot melt adhesive on both faces of shutter and fixing with stainless butt hinges of required size with neccessary full body threated star headed counter sunk s.s screw shall ,all as per direction of enginner In charge.

M&L for pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate etc. complete of frame size 125 x 60 mm complete all as specified and directed.

M&L for providing cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates for filling in the pressed steel door frame/hold fast complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F For Glazed and skelton shutters 35mm thick of 2nd class HW open rebated and prepared to receive glass or wire gauze etc. shutters divided in square with sash bars, size of members of shutters as specified in SSR Part-1, secton 8, clause 8.20(a) complete all as specified and directed.

S&F Galvanised MS wire cloth 0.46mm nominal dia of wire and average width of aperture 1.18mm, complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S&F for 100 mm butt hinges,Stainless steel complete all as specified and directed complete all as specified and directed.

S&F For MS 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door with hasp and size 300mm long with hasp, staples and fixing clips of sheet extruded section and fixing bolts of extruded section complete all as specified and directed.

S & F floor stopper 150mm length of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed

S& F stainless steel Peg set of six hooks size 50mm to 60mm complete all as specified and directed.

S&F for 150mm long aluminum handles, cast type, anodized complete all as specified and directed.

S&F for 150mm long aluminum, anodized, barrel tower bolts of extruded section and fixed.complete all as specified and directed.

M&L for preparation of treated/un-treated wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L steel window/ventilator factory made out of box type frame and shutter (double shutter, one for glazing another for flyproofing) made out of section using flash butt welding, hinges shall be provided to both shutters complete including all fittings and grills, all as per drg No CEPZ/TD/27/13 Sh 1/4 to 4/4 all as complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed .

Material and labour for plain cement concrete type B-1 1:2:4 (20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones, bed plates, kerbs ,water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for roof treatment with the following specification - applying water proofing treatment on horizontal or vertical surfaces by applying oil bound bitumen primer @ 0.20 Kg/sqm and providing 3mm thick APP modified water proofing membrane weighing not less than 3 Kg/sqm reinforced with non-woven polyester matt weighing not less than 160 gm/sqm, The overlap shall be minimum 100mm on transverse direction and 75 mm on longitudinal direction and sealing overlap by torch application and bonded and applying a coat of blown grade hot bitumen 85/25 over and below the membrane @ 1.20 Kg/sqm in drying over the membrane finished with solar reflective bituminous aluminium paint/primer @ 0.10 Kg/sqm over RCC roof slab/ parapet after cleaning the surfaces by removing dust, dirt etc. as per manufacturer’s instructions including 15mm thick screed in CM 1:4 and all as specified and as directed. NOTE :- The work shall be executed at site as approved by the GE.

S&F 110 mm bore PVC (SWR) Pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S&F 75 mm bore PVC (SWR) Pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S&F PVC (SWR) Bends in any radius 110 mm bore with access door complete all as specified and directed.

S&F PVC (SWR) Bends in any radius 75 mm bore with access door complete all as specified and directed.

S&F for 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed

S&F 110mm dia bore PVC SWR junction single (Double T) equal or unequal complete all as specified and directed.

S&F 75mm dia bore PVC SWR junction single (Double T) equal or unequal complete all as specified and directed.

S&F PVC (SWR) Vent cowl 75 mm bore in repair complete all as specified and directed.

S&F PVC (SWR) reducer 110x75mmcomplete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

M&L for Rotational moulded polyethylene water storage tank 3 layer white colour water tank, non- toxic effect, algea formation protection (made from Virgin grade of polyetylene material which is duly stablized with anti-oxidentPlastic) of capacity 1000 litres, (cylindrical vertical tanks with closed top,specific wt shall be 25 gm/ltr), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer, 20 mm dia PTMT valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and 20 mm brass stop cock etc complete all as specified and directed.

S&F in 15mm bore chromium plated cast copper alloy bib taps fancy type long body with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule all complete all as specified and directed.

S&F in brass chromium plated tubular towel rails 20mm dia D type 60cm long between flanges complete all as specified and directed.

S&F in repair/new flushing cistern with 10 ltrs discharge capacity PVC flushing cistern low level with inlet ball valve etc complete all as specified and directed. Cera Cat Part No: Congo B1010112 or equivalent in Jaquar/Prayag/ Kohler.

S&F Pillar tap cast copper alloy fancy type with capstan heads, chromium plated Fancy type screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long shanks and nut screwed for iron pipe of 15 mm bore complete all as specified and as directed.

S & F Vitreous china wash basin, white, flat back, size 550x400mm excluding pillar tap and including waste fitting chromium plated brass, chromium plated steel chain and rubber plug, porcelain stopper, a pair of CI brackets, waste pipe and excluding pillar tap, fixed in repairs complete all as specified and directed. Cera Cat Part No: Cana S2040119 or equivalent in Jaquar/Prayag/Kohler.

S&F Vitreous china urinal Flat Back Half stall type (white) of Size 375x390x590mm minimum with grating and union for discharge pipe including PTMT spreader of any colour for fixing with 15mm dia of pipe complete all as specified and directed. Make :- Cera Cat No : Chrys S4020103 or its equivalent in Jaquar/Prayag/Kohler

S & F in repair/new Vitreous China squatting pan “Orissa pattern” size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes etc, complete all as specified and directed.Cera Cat Part No: COVYNA S3010109 or equivalent in Jaquar/Prayag/Kohler.

S&F flush pipe of polythylene of low or high density or PVC 32mm dia for low/high level flushing cistern complete all as specified and as directed.

S&F of 15mm dia bore steel water GI tubes medium grade with all fittings and fixed cocealed to walls, ceilings or laid in floors complete including cutting/chiesling of brick/concrete surface and making good as per existing complete all as specified and directed

S&F of 20mm dia bore steel water GI tubes medium grade with all fittings and fixed cocealed to walls, ceilings or laid in floors complete with and including cutting/chiesling of brick/concrete surface and making good as per existing complete all as specified and directed.

S&F curtain rod aluminium alloy tubular with fixing brackets, stop etc. complete all as specified and as directed.

M&L for 75 mm thick PCC type D-2, 1:4:8 (40mm graded stone aggregate) as in sub base complete all as specified and directed .

Rammed earth filling under floor including Spreading and levelling in layers n exc. 25 cm thick and watering and well ramming complete all as specified and directed.

M&L Hardcore of broken stone or boulders of gauge n. exc. 63mm, deposited spread and levelled in layers n. exc. 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L Terra kota tiling 10mm thick set and jointed with grey cement with pigment and pointed with neat cement slurry in chajjas over 15mm thick screed bed in CM 1:4 over PCC coping 1:3:6 type C-1 (using 20mm graded agg), complete all as specified and directed.

M&L For Damp proof course 40mm thick in 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) to horizontal or vertical surfaces including necessary formwork complete all as specified and directed. (WPC Measured and Paid Separetely)

M&L Anti-termite treatment to the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for 10mm thick rendering/screeding on fair faces of brick/concrete surfaces in cement mortar 1:4 and finished even and fair for receiving tiles complete all as specified and directed.

M&L for Premium Quality Durastone / Endura heavy duty vitrified tiles of size 300 mm x 300 mm x 10mm to 12mm thick as in floors and skirting set and jointed in neat cement slurry and pointed in white cement to match the surface complete over screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L Glazed ceramic tiles in vertical surface 350x250mmx7mm/450X300X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

M&L Non-skid Ceramic coloured tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.18 sqm but n. Exc 0.38 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match shade including Screed bed or bedding layer 20mm thick in CM 1:4 for laying floor finishes complete all as specified and directed.

M&L For Non-skid Ceramic tiles 8 to 10mm thick (Square/Rectangular) polished area of each tile not exceeding 0.38 Sqm in skirting/dado set and jointed in neat cement slurry and pointed in white or coloured cement to match including Rendering 10 mm thick in CM 1:4 as for backing coat of wall tiles complete all as specified and directed.

M&L Non-skid Ceramic coloured tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but n . Exc 0.18 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match shade including Screed bed or bedding layer 15mm thick in CM 1:4 for laying floor finishes complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6, on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, preparation of new plastered surfaces of walls and applying 3mm thick wall care putty and two coat oil emulsion distemper on walls complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius with old size bricks built in cement mortar 1:6 incl complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius with old size bricks built in cement mortar 1:4 incl complete all as specified and directed.

M & L for Half thick Brick wall work curved on plan in any radius with old size bricks built in cement mortar 1:4 and external pointed flush in same mortar as the work proceeds complete all as specified and directed.

M&L For preparation of New Plastered surfaces and applying two coats of Acrylic emulsion ( Apex ) over a coat of primer complete all as specified and directed.

S&F chromium plated PTMT shelves fixed with and including chromium plated brass screws and plastic cleats complete all as specified and directed

S&F stop valve cast copper alloy chromium plated fancy type screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe complete all as specified and directed.

S&F long shank concealed type stop valve cast copper alloy chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe complete all as specified and directed.

S&F in repair/new chromium plated shower roses with or without swivel joints 125mm size including fixing to steel pipe or union complete all as specified and directed. Cat Part No: F7020111AB or equivalent in Jaquar/Prayag/Kohler.

M&L for concrete bed to drain pipes laid in trenches incl packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) for 150mm bore of pipe complete all as specified and directed.

M&L for Reinforced concrete pipes150mm, class NP3, laid and jointed complete with collars bed complete incl testing all as specified (Concrete to be measured and paid for separately) complete all as specified and directed

M&L for Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or conrete surfaces finishing the surface even and smooth without using extra cement mixed with liquid ater proofing compound @ 3% of cement weight complete all as specified and directed.

M&L for Precast Cover Slab, Gray Steel Fiber reinforced concrete 600x600x75mm Medium duty solid cover with frame complete all as specified and directed.

M&L 75 mm thick PCC, type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) as in plinth protection finishing the surface even and smooth without nusing extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in CM (1:3) finished surface even and smooth w/o using extra cement in ceiling. and applying three coats of white wash on ceiling complete all as specified and directed.

M&L Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished and reforming benching as required complete all as specified and directed.

Supply only integral Water Proofing Compound. complete all as specified and directed

Supply and laying for XLPE insulated, armoured, heavy duty electric cable with aluminum conductor, 1100 Volts grade, of size 16 Sqmm, 2 core complete all as specified and directed. Note : Earth work including excavation, returning filling , removing, sand cushioning, GI pipe,brick covering for mechanical protection of cable etc will be measured and paid for separately under respective items of schedule.

Supply and laying for XLPE insulated, armoured, heavy duty electric cable with aluminum conductor, 1100 Volts grade, of size 35 Sqmm, 3.50 core complete all as specified and directed. Note : Earth work including excavation, returning filling , removing, sand cushioning, GI pipe,brick covering for mechanical protection of cable etc will be measured and paid for separately under respective items of schedule.

Supply & laying of approved quality sand under cable upto 15cm before laying the cable and 8cm over the cable after laying, punned down to overall thickness of 18cm in trenches for cable cushioning complete all as specified and directed. (Punned thickness shall be measured)

Material and labour for well burnt, old size Sub Class 'B' brick covering protection to the eletric cable laid dry flat transversally along the length of cable with width equal to length of brick complete all as specified and directed .

Supply and fixing in trenches/under roads/under floor/on walls in new position tubing GI Light grade of 40 mm nominal bore of pipe with screwed sockets joints (such as bends, elbow, tees, etc) complete all as specified and directed

Supply and fix for DWC high density polythylene pipes having dia 63/50 as per site requirement having corrugation on the wall and plain surface on the wall conforming to IS : 14930 (Part-I & II) for protection of underground cable laid along pole/along wall/in PCC on GL/and including all fitting as required complete all as specified and directed.

Supply and fix gate valve 20mm dia gun metal gate valve conforming to IS with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Cutting and screwing existing steel tubing of 25mm dia for alterations or addition complete all as specified and directed.

S&F of 20mm dia bore steel water GI tubes medium grade with all fittings and laid in trenches/floor complete complete all as specified and directed.

Point wiring with 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable in and incl rigid PVC conduit concealed medium grade with pressed mild steel terminal boxes(sheet not less than 1.6 mm thick) duly painted with a coat of red oxide primer with suitable thickness plastic laminated sheet cover 3mm thick of adequate size for one light or one fan controlled by one switch incl 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable as earth wire(green colour) to common earth dolly complete all as specified and directed by Engr-in-charge.Note: a) Rate for cutting chases for conduits and sinking for boxes and making good to wall, floors deemed to be included in each point etc (b) On RCC roof ceiling PVC conduit shall be provided on surfaces for any necessary point with proper fixing clips and no extra cost shall be paid for the job etc complete all as per specified and directed. (c) colour coding is to be maintained. (Ph-Red, N-Block, Half-yellow, Earth-Green).

All as per item No 98 but for one 3 pin 5 Amp socket outlet on independent board complete all as per specified and directed.

All as per item No 98 but for one 3 pin 5 Amp socket outlet on same board complete all as per specified and directed.

Point wiring with 2.5 sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable drawn in and including rigid PVC concealed conduit medium grade of suitable size with sunk cast iron/pressed steel terminal boxes(sheet not less than 1.6mm thick) of adequate size with suitable thickness plastic laminated sheet cover 3mm thick for one 3 pin socket outlet 15 Amp on independent board including continuous 2.5 sqmm FRLS, PVC insulated and unsheathed copper conductor cable (multistranded) as earth wire to common earth dolly, complete all as per specified and directed.

S & F for switch piano flush type one way 5 amps SP complete all as specified and directed. Make: Havells (REO) or technocommerically equivalent make of cona/SSK.

S & F socket outlet 3 pin 5 amps flush type complete all as specified and directed. Make: Havells (REO) or technocommerically equivalent make of cona /SSK.

Supplying & Fixing switch socket combination 2 in 1, 15 pin, 5 amps, 230 volts, flush type complete all as per specified and directed. Make: Havells (REO) or technocommerically equivalent make of cona /SSK.

S&F Lamp holder, PVC/Polycarbonate type with bakelite back plate having matching colour to holder suitable for angle/batten fittings complete all as per specified and directed.

S&F ceiling rose surface 65x50mm three terminal with bakelite back plate complete all as specified and directed.

S&F of LED Bldg security lights of 35 Watt, 230 V having pressure die cast aluminium housing with system lumens efficacy≥100 lumen/W IP65 protection, IK07 rating, inbuilt electronic driver with PF>0.95 incl Gl bracket of suitable dia bend to shape and fixed to wall by means of clamps or nuts bolts and connecting up with three core twisted flexible copper conductor cable. Make of street light fitting-Bajaj, cat part no:ENXT P 35L WH PO PC SD/Havells, cat part no: ENDURASUNDOWNSL35WLED765PASYBOPC/ Wipro, cat part no:LR08-501-XXX-57-XX/Crompton, cat part no:TRP-400-35-57-SL-LM-NSR including taking out old/unsv securtiy light any type and rating complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose of make : Philips, cat part No :BN170C LED20S-6500 PSU L120 /Havells, Cat part no: LUMILINEPLUSNEOBS20WLED865SPCSSIND/ Crompton, cat part no : CCS-100-20-65-HL2-DP-NWH/ Orient, cat part no :LBLN-20-C-SQ-AL complete all as specified and directed

Supply and fixing of Environmental friendly, ultra modern, pre die cast aluminium housing ,energy saving, surface mounted, decorative hexagon bulk head Back-lit LED luminaire comprising of high brightness LEDs. suitable for 10W IP-66 of make : Havells, cat part no :HEXAFT10WLED857SSYMBOPC/Crompton, cat part no : CIS-306-10-57-SL-DP-NBK/Orient, cat part no :LIBHP-10-C-V1 complete all as specified and directed.

M&L for SPN MCB DB 6 way sheet metal enclosures double door 230 V AC, 50 Hz AC with IP 43 and IK 09 rating having fully insulated copper busbar, neautral bar, earth bar and cable ties for cable management including polyuthrene gasket complete fixed flush in wall including cutting chases on wall for taking out old DB and fixing of new DB and making good disturbed surface of wall with cement mortar and finishes to match exisiting surface complete all as specified and directed.

S&F MCB SP 6-32 Amps with 10KA breaking capacity of 'B' series in distribution board complete all as per specified and directed.

S&F in replacement MCBs single pole and neutral (SPN)/ isolator 40 Amps with 10 KA breaking capacity of 'B' series in distribution boards all as specified and directed.

Supply and fixing ceiling fans copper wounded complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

M & L for providing/cutting the round /square hole on the wall and supply and fixing propeller type AC ventilating fans(Metalic body ) Single phase , 230 volts 300 mm sweep including grouting and fixing the ragged bolts in wall for exhaust fan and louver shutter on the exhaust side wall (outer surface of the wall ) and connecting PVC insulated three core 1.5 SQMM copper cable from ceiling rose to exhaust fan motor and writing MES No with black synthetic enemel paint 2.0 cm high Make of Exhaust fan - Havells, model no : Ventil Air DS Green /Standard, model no :Refresh air - SPS/Khaitan, model No: Eurocap complete all as specified and directed.

Supply, fixing and testing for Horizontal/cubical type BEE 5.00 water heater storage type with multifunctional safety valve, elecrtic operated 230 volts, single phase complete including one no of heating element, automatic, thermal cut out, fusible plug, anti vaccum system, built in pressure release valve, thermostat, rust proof powder coated body, indicator lamp and all safety advices as per E-in-C branch techanical instructions and of capacity 25 liters including with suitable and making good the distrubed surface and matching with exisiting complete all as specified and directed.

Supply, installing, testing of LT outdoor Panel vermin/dust/weather proof self ventilation with wire mesh at suitale interval on both side, totally enclosed bus bar chamber fully comparted type, front openable hinged independent door for each compartment with locking arrangement and common openable hinged door from rear side suitable size 600x800x350 made out of 3.15mm thick CRCA sheet duly powder coated paint, 415 volts, TPN, 50 HZ both sides properly welded MS angular supported with Stand of size 50x50x6mm incoming/outgoing feeders by providing cable glands and cable lugs complete all as specified and directed comprising of following accessories:- (i) Incoming 63 Amp FP 25KA MCCB with adjustable thermal setting with on/off/trip indicator and standard extended rotary Handle spreaders, Phase Barrer -INO Bus bars : 100 A TPN + E aluminium busbars suitable for 50 KA for 1 sec feeders.

M&L earthing complete with galvanised steel earth plate eletrode 600mmx600mm and 6mm thick buried directly in ground earth pit not less than 2.25mtr deep below normal ground level with top edges, of the plate not less than 1.5m below normal ground level, connected to the Galvanise Iron earth lead 25mmx4mm (GI Strip) size, by means of bolts, nuts, check buts and washers of galvanised iron and 32mmx6 mm earth lead protected by provision of GI medium grade pipe 40 mm bore including provision of aggregates with 40 mm thick cover of RCC (1:2:4), reinforced with XPM (weight not less than 4 kg per sqmm) and frame of angle iron 40mmx40mmx3mm and with 6 mm dia MS bar handle made to shape, GI light grade 20mm bore pipe of suitable length for watering perforated at bottom placed on top edged of earth plate, common salt and charcoal filling, funnel, wire mesh and earth work in hard/dense soil, returning filling in distance not exceeding 50 mtr and removal of surplas soil to plate No 3 of SSR 2009 Part-I and connecting to feeder pillers and Transformer all as specified including testing on completion complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.5 of SSR Part-I (2009) including filling of charcoal dust, common salt all around Earth plate upto 150mm, 20mm bore GI medium grade watering pipe, 15 mm bore light grade earth lead protection pipe upto main board, funnel with wiremesh, 40mm thick RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate reinforced with suitable handle and angle iron frame and necessary excavation and earth work in any type of soil etc. complete all as specified and as directed including testing on completion. (Note: The rate quoted include cost of min 7.5 metre earthling wire .)

MANOTRA BUILDER (BID ID -3493201)