GE/U(N)-44/2020-21 SPL REPAIR TO BLDG NO P-4 OR MD ACCN AT HQ 71 SUB AREA UNDER GE (NORTH) UDHAMPUR

Amount

Taking down exsiting water proofing treatment incl PCC padding, plaster, etc complete necessary removal of debries from site complete all as specified and directed by Engr-in -charge

40 mm thick PCC (1:2:4) type B-0, (using 12.5 mm graded crushed stone aggregate) in two layers (each 20 mm) with chicken mesh provided between the layers and finished even and smooth with false grooves @ 450x450 mm complete all as specified and as directed.( Note: Chicken wire mesh shall be measured and paid separately under respective item of sch 'A").complete all as specified and directed by Engr-in -charge

Galvanised steel wire cloth size of 20 mm but 0.36 mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and directed by Engr-in -charge

10mm thick cement plaster on fair face of concrete surface including repair of doubing roof surfaces in CM 1:3 finished even land smooth without using extra cement over complete all as specified and directed.(Water proofing compound shall be measured and paid sepratly )

Supply only integral water proofing compound complete all as specified and directed by Engr-in -charge

Preparing RCC roof slab top by wire brushing and cleaning the dust and forign materail etc complete and applying a coat of hot blown bitumen 85/25 grade @ 1.20kg/Sqm over a coat of bitumen primer @ 0.40 ltrs/Sqm and there after laying of a layer of APP based polymeric membrane (five layered with centre core as 100 microns high molecular high density polyethylene film) weighing 3kg/Sqm and will be laid as per MES SSR Pt-I para 11.43.2.2 with minium side lap 75 mm and end Lap of 150 mm bonded with hot blown bitumen 85/25 gde penetration @ 1.20 kg/sqm and blinded with fine sand in dry condition (pleable free) @ 0.50 kg/sqm dusted over the bitumen coat complete all as sp[ecified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and recast concrete articles all as specified.

Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) with old size bricks complete all as specified and directed by Engr-in -charge

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.complete all as specified and directed by Engr-in -charge

Rendering 15 mm thick in cement mortor 1:4 on fair faces of brick work or concrete surfaces complete all as specified and as directed.

Rendering 5 mm thick in cement mortor 1:3 on fair faces of brick work or concrete surfaces complete all as specified and as directed.

Rendering 10 mm thick in cement mortor 1:6 other than fair faces of brick work or concrete surfaces complete all as specified and as directed.

Complete removal of existing treatment, preparation of plastered surfaces of wall and applying two coats of cement base paint over one coat of cement primer including 1 mm thick exterior wall care putty ( to be applied in two coats) all as specified. Note: Putty surface shall be rubbed with emery paper to form even and smooth surface.

Two coat of cement base paint over a coat of alkali resistant primer paint including preparation of newly plastered of wall.complete all as specified and directed by Engr-in -charge

Complete removal of existing treatment,preparation of surfaces of old wall surfaces and applying two coats of oil bound distember over one coat of primer paint over and including wall care putty complete all as specified and directed by Engr-in -charge

Two coats of oil bound distember over a coat of primer over two coats of approved wall care putty over and including preparation of new plastered surfaces of wall complete all as specified and directed.

Complete removal of existing treatment,preparation of surfaces of ceiling surfaces and applying two coat of white wash over coat of primer of old surfaces complete all as specified.

Taking down the shutter of any description exc 1 sqm but n.exc 2sqm each complete all as specified and directed by Engr-in -charge

Taking down Chowkats or frames exc 1.5 Sqm but not exceeding 4 Sq.M each (Without taking off shutters from the frames) complete all as specified and directed by Engr-in -charge

do but area n.exc 1.5 sqm complete all as specified and directed by Engr-in -charge

Second class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed by Engr-in -charge

35 mm thick 2nd class HW rail and style Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle boardwith commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engr-in -charge

35 mm Glazed and skeleton shutters, 2nd class H.W open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engr-in -charge

125x 60 mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified.

105x 60 mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wall nut colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed by Engr-in -charge

Factory Made Solid PVC Moulded Door Shutter wall nut colour, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the ront face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing but 2mm thick Moulded Prelam PVC Sheet on the front ace & 2mm Plain colour PVC Sheet on back face complete all as specified and directed by Engr-in -charge

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel staples complete, all as specified and directed by Engr in Charge.

Powder coated (of approved colour ) aluminium sections as in frame & shutter of windows (Hung/sliding), ventilators (louvers/fixed type) and fixed frame etc fixed to wall including rollers for sliding shutter and necessary locking arrangement, preparation of disturbed portion both side (internal & external surfaces of wall) match with existing surface treatment and all sides of aluminium frame shall be sealed with silicon sealent (inner/outer face) complete all as specified as directed by Engr-In-Charge. Make : JINDAL/ HINDALCO/INDALCO/

Stainless steel mosquito proof wire cloth of stainless 0.36mm dia and 1.4mm aperture fixed with aluminium flat/channel and screws all as specified as directed by Engr-In-Charge.

Glazing with 5.50 mm thick tinted/plain/frosted/itched glass exc 0.50 sqm in each panel fixed to aluminium section of windows/vendilator and fixed frame with suitable EPDM rubber packing and powder coated aluminium beading to frame complete all as specified.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or gorged into spikes, framed guard bar, barred iron doors; ladder, framed balusters; railing; frame work for water tanks, cooler stand etc and similar work conforming to Fe 290 or Gde-E-165, complete all as specified and as directed.

In repairs 0.80 mm Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and ixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred fixed in position all as directed by Engr-in Charge.

Preparation of new steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer.complete all as specified and directed by Engr-in -charge

300 mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on olt plate and two on staple plate and fixed complete all as specified and directed by Engr-in -charge

150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in -charge

125 mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engr-in -charge

100 mm Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed by Engr-in -charge

Small fittings 1st class hard wood such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and directed by Engr-in -charge

In reapirs 25 mm dia MS powder coated antique type curtain rods with bracket fixed to wall with suitable screws and onion type end brackets all as per approved design/colour/pattern fixed as directed in Engr-in-Charge.

Two coat of enamel paint on wooden surfaces over a coat of primer incl preparation of new Surfaces of any description, not otherwise descri-bed, over 10cm width or girth complete all as specified and directed by Engr-in -charge

do but one coat of synthetic enamel paint except primer on old surfaces complete all as specified and directed by Engr-in -charge

Dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in -charge

Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement lurry and pointed in white or coloured cement to match including 10 mm screed bed 1:4 cement mortar complete all as specified and directed by Engr-in -charge

Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed with spacer and laid with epoxy grout in neat cement slurry and pointed to match including 10 mm screed bed 1:4 cement mortar complete all as specified and directed by Engr-in -charge

Glazed ceramic tiles 300x450x7 mm to 8mm thick in vertical surfaces such as skirting, dadao and risers to steps over 10 mm thick in CM(1:4) incl taking down from existing surfaces.complete all as specified and directed by Engr-in -charge

Demolition of rerinforced cement concrete of any description and in any position.complete all as specified and directed by Engr-in -charge

Reinforced cement concrete, 1:11/2:3, type A-1 (using 20 mm graded stone aggregate) as in slab supported on walls, beams and columns in floor, roofs, landings, balconies, canopies, shelves and like complete all as specified and directed.

Formwork to sides and soffits of suspended slabs such as roof slabs, floor slabs,beams landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engr-in -charge

Ditto, but edges of slab exc 10cm but not exc. 20cm wide complete all as specified and directed by Engr-in -charge

TMT bars 8mm dia and over cut to length bent to shape required including cranking bending spirally for hopping for columns,hooking ends and binding with and including MS wire (annealed) not less than 0.90 mm dia confirming to TMT bars complete all as specified.

Granite stone slab flooring 16 to 18 mm thick machine cut, rounding edges and polishing , bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, over 20mm thick screed bed bedding in CM 1 :4 complete all as specified and as directed.

Looking mirror of size 450 x 600 using 5 mm thick mirror edges rounded fixed with clips all as specified incuding teak wood/pvc frame of size 25 x 25 mm decorativ and water proof including malimine polishing.complete all as specified and directed by Engr-in -charge

Viterous china wash basin,white colour flat back size 550X440 mm incl waste coupling cp 32 mm dia chin and plug and porcelain stopper and CI brackets of iron 65x65x6mm embedded in pcc block with pcc 1:2:4 type B-1 and PVC waste pipe 32 mm dia & CP grating with holes with full pedestal of china ware,including PVC connection 15mm size with PTMT nuts of length 600mm and pillar mixer 'Hot and cold',fancy type,cast copper alloy, with capstan heads,chormium plated,screwed down,high pressure,with or without lettered with long screwed shanks and fly nuts, screwed for iron pipe of bore 15mm,fixed in complete all as specified and as directed by Engr-in-Charge.

75 mm bore PVC (SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr-in -charge

110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps, all as specified and directed by the Engr-in-charge.

PVC (SWR) bends 75 mm bore any radius with oveal & acces door complete all as specified and directed by Engr-in -charge

S&F PVC (SWR) bends any radius in 110 mm dia complete all as specified and directed by Engr-in -charge

(SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed by Engr-in -charge

PVC (SWR) floor trap plain/multi with grating incl. jointing with solvent cement (75 mm bore) complete all as specified and directed by Engr-in -charge

In repairs sinks made of stainless steel l mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engr-in -charge

In repairs made of stainless steel , 0.60 mm thick for kitchen plate rack , with plug , washers, fixing on wall, over all size 750x900 mm complete all as specified and directed by Engr-in -charge

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in mortarcomplete all as specified and directed by Engr-in -charge

Machine cut kota stone slab flooring 18-20mm thick over 15 mm th cement screed in CM 1:4 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in -charge

Demolition of un-reinforced cement concrete in roofs,floors ( other than ground floors), beams, staircase, landing, chajjas and similar suspended work.of and pavings not exceeding 15 cm thickness(below or above ground level) complete all as specified and directed by Engr-in -charge

25 mm thick plain cement concrete1:2:4 type B1(using 20 mm graded stone aggregate) as in subbase of flooring all as specified and as directed.

Providing and laying water proofing treatment to sunken portion of WCs, bathrooms, etc by applying two coat of slurry of cement @ 0.488kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.253kg/sqm this layer allowed to air cure for 4 hrs then applying slurry of cement @ 0.242 kg/sqm mixed with acrylic based polymer modified cementitious composite compound @0.126kg/sqm and allowed to aircure for 4 hrs and joints seal with sealing compound as approved by GE complete all as specified and directed by Engr-in -charge Note: (i) Before laying of lime concrete joints of trap/WC/Soil pipes shall be properly sealed with sealing compound of Roofex/Forre/FOSROC and provn of P or S trap & Nahani /Floor traps with long arm and also provn of spout of 40 mm dia.

Rendering 15mm thick on fair faces of brick work or concrete surfaces in Cement mortot as in CM 1:3 finishing even & smooth w/o using extra cement, complete all as specified and as directed.

Lean concrete using 40mm graded stone aggregate as in 1:5:10 as in filling sunken portion treatment, complete all as specified and as directed.

In repair Vitreous China Squatting pan "Orissa pattern" long pan, size 580 x 440 mm white ,with `P' or `S' trap, front or back inlet and foot rests any pattern including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including lime concrete complete all as specified and directed by Engr-in -charge

In repairs PVC connections 15mm size with PTMT nuts of length 300mm complete all as specified and directed by Engr-in -charge

In Repair PVC valveless , syphonic action type, Flushing cistern low level, white , with inlet, ball valve, float and handle including brackets,10 ltrs capacityincl suitable pvc flushing bend complete all as specified and directed by Engr-in -charge

n repairs Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed by Engr-in -charge

Angle cock concealed valve cast cpper alloy fancy type 15 mm complete all as specified and directed by Engr-in -charge

In repair Bib tap cast copper alloy fancy type suitable for15 mm dia pipes complete all as specified and directed by Engr-in -charge

In repair Corner glass shelf complete all as specified and directed by Engr-in -charge

CP towel rail 600 mm complete all as specified and directed by Engr-in -charge

CP towel ring square complete all as specified and directed by Engr-in -charge.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for Refixing or removal .

Taking up or down 25 mm bore steel tubing and connections, including cleaning for Refixing or removal .

15 mm bore Galvanized Steel tubes, medium grade with all fittings for water supply pipes etc., laid in trenches/fixed on walls. complete all as specified and directed by Engr-in -charge

25 mm bore Galvanized Steel tubes, medium grade with all fittings for water supply pipes etc., laid in trenches/fixed on walls. complete all as specified and directed by Engr-in -charge

In repairs for 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified

20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed in position complete all as specified and directed by Engr-in -charge

GI Unions,20mm brass to connect iron to polyethylene and fixed complete all as specified and directed by Engr-in -charge

50 mm thick Cement concrete type C-2 , 1:3:6 using 40mm graded aggrigate Finishing surfaces of concrete topping even and fair finishes (without using extra cement) as in plinth protection all as specified and directed by Engr-in- Charge.

In repair 20 mm thick cement plaster on fair face of concrete surface including repair of doubing roof/chajja/facia surfaces in CM 1:3 finished even land smooth without using extra cement over complete all as specified and directed.(Water proofing compound shall be measured and paid sepratly ) complete all as specified and directed by Engr-in -charge

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends swan necks, etc, including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fitting and accessories).complete all as specified and directed by Engr-in -charge

Dismantling boarding, any description, fixed in any position with nails all as directed.

18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with crews to timber frame work(Lamination/sunmica shall be measured by separately) complete all as specified and directed by Engr-in -charge

30mm Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed by Engr-in -charge

Aluminium handles, cast type, anodised 100mm long complete all as specified and directed by Engr-in -charge

Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed by Engr-in -charge

Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed by Engr-in -charge

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and directed by Engr-in -charge

Cement concrete 1:3:6 using 20mm graded aggregate, as in coping including necessary form work complete all as specified and directed by Engr-in -charge

Taking down carefully aluminium/copper point wiring ,light fan socket, or power complete with (fittings such as old rusted steel conduit switches ceiling rose pendants, regulators, socket etc to be measured separately) removing material to store for disposal by credit and making good to disturbed surfaces of walls floors etc and all as specified.

Point wiring with 1.5sqmm PVC insulated unsheathed FRLS cable with multistranded copper conductor medium grade ISI marked drawn into and including PVC concealed conduit with all accessories for one light/fan/bell point controlled by one switch and also including 1.5 Sqmm continuous earth wire connected to common earth dolly complete all as specified and directed.

Point wiring with 1.5sqmm PVC insulated unsheathed FRLS cable with multistranded copper conductor medium grade ISI marked drawn into and including PVC concealed conduit with all accessories from terminal box to junction of ceiling and wall and rest of circuit conductor wires drawn into and including surface PVC rigid non metallic conduit for one ceiling fan point controlled by one switch and also including 1.5sqmm continuous earth wire connected to common earth dolly complete all as specified and directed.

All as per item No. 98 above but for 6 pin socket outlet 15 Amp with 2.5 Sqmm on independent board incl. 2.5 Sqmm stranded copper conductor earth wire connected to common earth/earth dolly complete.

All as per item No 98 above but for –do—5 pin socket outlet 5 Amps on same board.

All as per item No.98 above but for –do—5 pin socket outlet 5 Amps on independent board.

Point wiring with 1.5sqmm PVC insulated unsheathed FRLS cable with multistranded copper conductor medium grade ISI marked drawn into and including PVC concealed conduit with all accessories for 2 way point controlled by two way switch and also including 1.5sqmm continuous earth wire connected to common earth dolly complete all as specified and directed.

Supply and replacement of switch piano flush button single pole 5 Amps 230 Volts one way complete all as directed.

Supply and replacement of socket out let 2 in 1, 3 pin 5 Amps flush type 230 Volts complete all as directed.

Supply and fixing switch & socket out let 2 in 1, 6 pin 5 Amp and 15Amp 230 volts on independent board complete all as directed.

Supply and replacement of switch piano flush button 2 Way, 5 Amps 230 Volts one way complete all as directed.

Call bell Ding dong type complete all as directed.

Supply and fixing of bell push , flush type 5 amp complete all as specified and directed by Engr-in -charge

Supply and replacement ceiling rose surface bakelite type 65x50mm three terminals complete all as specified and directed by Engr-in -charge

Supply and replacement stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc suitable for 1200/1400 mm sweep complete all as directed.

Supply and replacement of decorative ultra slim linear LED lighting fixture 18/20 watt LED complete making all connection using 1.5 Sqmm copper conductor multistranded PVC insulated twin core flexible cable from ceiling rose to fitting drawn through in PVC flexible conduit of same colour to match with fittings/wall surface complete all as per directed by Engr-in-charge. Make CROMPTON GREAVES cat part no. LCTL-18-CDL / WIPRO Product Code-D532065 / Havells Ordering Code -LHEXBYPNIN1W020.

Supply and replacement of decorative ultra slim linear LED lighting fixture 5/7 watt LED complete making all connection using 1.5 sqmm copper conductor multistranded PVC insulated 2 core flexible cable from ceiling rose to fitting by using extra length flexible cable 2 core other than provided by manufacture complete all as per directed by Engr-in-charge. Wipro product code D530565 OR HAVELLS ordering code LHEXBYPNIN1W005 OR CROMPTON GREAVES cat part no. LCL-07-CDL.

Supply and replacement of decorative ultra slim linear LED lighting fixture 10/12 watt LED complete making all connection using 1.5 sqmm copper conductor multistranded PVC insulated 2 core flexible cable from ceiling rose to fitting by using extra length flexible cable 2 core other than provided by manufacture complete all as per directed by Engr-in-charge. Make : CROMPTON GREAVES cat part no. LCL-12-CDL OR WIPRO Product Code-D531065 /Havells Ordering Code -LHEXBYPNIN1W010 /Wipro, product code no-D531065 OR CROMPTON GREAVES cat part no. LCL-14-CDL.

Supply and replacement new generation energy saving LED bulk head 9/10 Watt with opal diffuser suitable for 600 LUMEN complete. Make-CROMPTON GREAVES ( cat part no. LBHP-10-CDL) or equivalent model in Havells cat part no:- LHEXCFP7PN5W010 or WIPRO CAT PART NO. LR02-261-XXX-57-XX.

Supply and fixing decorative wall light fixture made up of polycarbonate suitable for 12 Watt LED lamp complete making all connection using 1.5 sqmm copper conductor multistranded PVC insulated cable complete all as per directed by Engr-in-charge. Make Havells Cat part No/ Ordering code LHFOFTE1TZW012 or equivalent model of Phillips/CG/Bajaj.

Supply & Fixing LED security light fitting Endura Pearl 18/20 Watt new generation energy saving and environmental friendly, long life, LED street light made up of pressure dia cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP OPENING separate driver compartment with IP66 protection and impact resistance of IK07. Including all accessories and connection with suitable cable from ceiling rose to light fitting and fixing on GI pipe bracket made out of suitable dia GI pipe medium grade 1.2mtr long bent to shape and fixed on wall with flat iron clamps, nut, bolts washer etc all as specified and directed. Make Havells Cat part No ENDURAPEARLSL20WLED757SASYTOPC, Code- 9405. or equivalent Crompton Greaves cat part no. LSTS-20-CDL OR WIPRO product code D912065.

Supply and replacement of sheet metal enclosure for DBs IP-43 double door when MCB's to be used single pole & neutral 240 Volts 8 Ways all as specified and directed by Engr-in-Charge.

S&F MCB 6 to 40 Amps SP 240 volts C curve complete all as specified and directed by Engr-in -charge.

S&F MCB 20 to 63 Amps SPN 240 volts C curve complete all as specified and directed by Engr-in -charge.

Taking down ceiling fan /exhaust fan complete including overhauling, cleaning with soft solution and painting of the same with white enamelled paint including painting of MES number as existing, or re-hanging ceiling fan / exhaust fan and connecting up including provision of three core copper conductor cable 1.5 sqmm nominal cross sectional area and length not less than 0.5 mtr from ceiling rose to fan complete all as specified and directed

M&L for sub main wiring with two run of 4.00 Sqmm (2x4.00 Sqmm) 1100 Volts grade single core FR PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metallic PVC rigid conduit 25 mm dia ISI marked with all conduit accessories mounting on surface of walls /roofs / ceiling including cutting chasing and with one run of 2.5 Sqmm (1x2.5 Sqmm ) single core FR PVC insulated unsheathed copper conductor cable as earth wire complete all as specified and directed.

Taking down old XLPE insulated aluminium conductor armoured cable of size 25 Sqmm 2 core. Complete all as specified and directed.

Supply laying and testing cable XLPE insulated, screened, PVC bedded galvanised steel strip or wire armounded electric power cables (heavy duty) 1100 Volts conductor of size 25 Sqmm 2 core completed all as directed.

Excavating in trenches in any type of soil n exc 1.5 m wide and n exc 1.5 m in depth for laying of under ground cable, electric pole and getting out complete all as directed.

Returning filling in (soil) including spreading, levelling, watering and well ramming in layers n.exc 25cm thick all as specified and directed.

Removing excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed by Engr-in -charge.

Sand cushioning to under ground cable with a layer of 8 cm deep before laying and 15 cm covering above the top edge of cable after laying all as specified

Supply and lay brick class B covering as mechanical protection to cable with well burnt all as specified.

M&L GI tubing light grade with all fittings and fixed in wall and floor or fixed to pole of size 40 mm dia. Complete all as specified and directed.

Earthing in repair complete with galvanized steel earth electrode 60cmX60cmx6 mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level ) with top edge of the plate not less than 1.5m below normal ground level connected to earth lead by means of bolts nuts and washers of GI steel and including earthing pit charcoal, common salt, GI 4.0mm dia lead wire 20mm GI medium grade watering pipe 15mm bore light grade protection pipe 5 Mtr length with wire mesh and funnel PCC pit in PCC 1:2:4 type B-1 using 20mm graded stone aggregate, angle iron frame and RCC cover and earth work complete all as shown in electrical plate No.3 of SSR -2009(Part-1)complete all as specified and directed by Engr-in -charge

ATUL TRADING CO

KUMAR CONSTRUCTION CO

JOGINDER SINGH

paras ram pachiala

jyoti parkash sharma

M/S Vishwa Mittar Pachyala

TULSI RAINA AND SONS