SPL REPAIR TO BLDG NO. P-366 AGAINST JOB NO. 81 SA/BTD/SR(BLDG)-09/2024-25) UNDER GE NORTH BATHINDA AT BATHINDA MIL STN.

Amount

Dismantling brick tiles / PCC terracing tiles single layer laid on roof and pointed with cement mortar complete all as specified and as directed by Engineer-in-charge.

Demolition of mud in roofs, any thickness, including plastering and leaping (whether full thickness removed or only a part there of) including removing/cutting uprooting grass, vegetations and roots of small plants etc on roof floor and surrounding/parapit wall etc, including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for PCC padding in 1:2:4 Type B-0 (using 12.5 mm graded stone aggregates) as in roof slab finishing the surface even and fair and maintain roof slope during the execution of work including Liquid water proofing compound complete all as specified and directed. Liquid Water proofing compound shall be measured and paid separetly as supply only under appropriate item of Schedule 'A' BoQ.

Material and labour for 15mm thick Screed bed or bedding layear in Cement mortar 1:6 on roof surfaces, parapet or vertical beam surface (horizontal or Vertical) finishing the surfaces even and fair complete all as specified and directed by Engineer-in-charge.

Material and Labour for Water proofing tratment to roof / terrace (material of water proof treatment as approved by GE) Single component, acrylic based, flexible, micro fibre reinforced waterproofing and heat reflective coating system. the treatment shall be carried out as per the manufacturers instructions and shall include the followings: (a) Preparation of substrate and cleaning it off all loose and triable by mechanical means (b) Open the cracks lines to form , V grooves with cutter/hammer/chisel up to 5-10mm and filling with crack filler and PU sealant. (c) application of primer coat @ 0.2 to 0.3 kg/ sqm followed by the first coat @ 0.75kg/ Sqm. (d) The second coat shall be applied @ 0.75 kg / Sqm and reinforced with fabric re-inforcement between the first and second coat. (e) The top coat of primer shall be applied after the second coat dries off @ 0.05-0.08 Kg per Sqm. (f) The material shall adhere to following specification. TECHNICAL SPECIFICATION OF MATERIAL Tensile Strength 1.5 MPa ASTM D412 Elongation at Break > 200% ASTM D412 Adhesion in Peel > 1.5 MPa (on concrete substrate) EN 1542 Crack Bridging Ability Passes upto 3.2mm Width ASTM C1305 Permeability to Water Vapour Passes IS 2645 Water Vapour Transimission ~ 23 g/m²/24hr ASTM E96 Water Absorption < 10% ( by Mass) ASTM D570 Microbiological Resistance No Algae & Fungal Growth ASTM D5590 Solar Reflectance Index 102 ASTM E1980. Note : Complete material shall be approved by GE and procured in bulk and kept in lock and key. Note : The installation company should be trained and authorized by Manufacturer & installation to be carried out as per manufacturers approved method statement. All auxiliary & accessories involved during application should be supplied by single manufacturer as a part of system. Any component used which is not manufactured by the particular manufacturer can only be used with official approval from manufacturer in consultation with GE.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed by Engineer-in-charge.

Material and labour for 15mm thick Rendering in Cement mortar 1:6 on brick work or concrete surfaces of walls and finishing even & smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Cement plastering 10mm thick in cement mortar 1:3 on fair faces of concrete ceiling surfaces finished fair & even without using extra cement complete all as specified and directed by Engineer-in- Charge.

Material and labour for 15mm thick Rendering in Cement mortar 1:4 on other than fair faces of brick work or concrete surfaces of walls and finishing even & smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

Material and Labour for prepration of new surfaces and applying acrylic wall care putty on internal surfaces of wall (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and leveling of surfaces in two or more layers) by using ready made acrylic wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc and with and including applying 02 coats of interior emulsion paint (shade as approved by GE ) , @ 10 sq.m/litre/2 coats by using roller to internal wall surfaces over with and including one coat of interior emulsion primer @ 10 sq.m/litre/1 coat by using roller as recommended for under coat by manufacturer of interior emulsion by using the brands of interior emulsion paint and interior emulsion primer as described in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after complete all as specified and directed by Engineer-in- Charge. Make of acrylic wall care Putty : As described in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after. Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order. (ii)The make of acrylic wall care putty shall be as per the recommendation of manufacturer of paint.

Material and Labour for prepration of new surfaces and applying acrylic wall care putty on internal surfaces of wall (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and leveling of surfaces in two or more layers) by using ready made acrylic wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc and with and including applying 02 coats of exterior emulsion paint (shade as approved by GE) with highlighter of any approved shade, @ 5 sq.m/litre/2 coats by using roller to external walls/ RCC surfaces / soffits of chajjas / roof projections / cantilevers / balcony etc surfaces over with and including one coat of exterior wall primer @ 11 sq.m/litre/1 coat by using roller as recommended for under coat by manufacturer of exterior emulsion by using following brands of exterior emulsion paint and exterior emulsion primer as described in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after complete all as specified and directed by Engineer-in- Charge. Make of acrylic wall care Putty : As described in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after. Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order. (ii)The make of acrylic wall care putty shall be as per the recommendation of manufacturer of paint.

Material and Labour for preparing new plastered surfaces of ceilings and applying three coats of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the last two coats of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and directed by Engineer-in- Charge.

Complete removal of existing treatment of any type/description from walls/RCC surfaces/ceiling/chajjas/roof projections etc with mechanical means/grinder complete all as specified and directed by Engineer-in- Charge.

Material and Labour for applying acrylic wall care putty on internal surfaces and external surfaces of walls/ceilings/soffits (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and leveling of surfaces in two or more layers) by using ready made acrylic wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed by Engineer-in- Charge. Make of acrylic wall care Putty : AS described in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after. Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order. (ii)The make of acrylic wall care putty shall be as per the recommendation of manufacturer of paint.

Material and Labour for prepration of surfaces with and including applying 02 coats of interior emulsion paint (shade as approved by GE ) , @ 10 sq.m/litre/2 coats by using roller to internal wall surfaces over with and including one coat of interior emulsion primer @ 10 sq.m/litre/1 coat by using roller as recommended for under coat by manufacturer of interior emulsion by using the brands of interior emulsion paint and interior emulsion primer as described in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after complete all as specified and directed by Engineer-in- Charge.

Material and Labour for prepration of surfaces with and including applying 02 coats of interior emulsion paint (shade as approved by GE ) , @ 10 sq.m/litre/2 coats by using roller to internal wall surfaces by using roller as recommended for under coat by manufacturer of interior emulsion by using the brands of interior emulsion paint as described in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after complete all as specified and directed by Engineer-in- Charge.

Material and Labour for preparing of surfaces of walls and applying two coats of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) removing serviceable tiles to store and and including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for abrasion resistant ceramic tiles, area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, 9-10mm thick (square), polished, shade and colour as approved by GE, in floors with and including 10mm thick bedding layer using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement having scratch hardness of surface min 6 on Mohs Scale and abrasion resistance of class V completed all as specified and directed by Engineer-in-charge.

Material and Labour for abrasion resistant ceramic tiles, area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, 9-10mm thick (square), polished, shade and colour as approved by GE, in vertical surfaces as in skirting/ Dado with and including 10mm thick bedding layer using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement having scratch hardness of surface min 6 on Mohs Scale and abrasion resistance of class V completed all as specified and directed by Engineer-in-charge.

Material and Labour for anti slip coloured ceramic tiles 7 to 8mm thick (square/rectangular) of Size 400mmx400mm Sqm in floors and Skirting etc. including 10 mm thick bedding layer using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in white or coloured epoxy grout to match the shade of tile including necessary cutting as per site requirement complete all as specified and as directed by Engineer-in-charge.

Material and Labour for glazed ceramic coloured tiles 7.5 mm to 8.5mm thick 450mm x 300mm size in verticle surface including 10mm thick backing coat using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement etc complete all as specified and as directed by Engineer-in-charge.

Material and Laboue Marble tiles 30cmx20cmx20mm thick machine cut, bedded jointed and pointed with grey cement slurry Including and polishing type, shade and colour as approvd by GE, in floor, etc set and jointed in neat cement slurry @3kg / Sqm and pointed in white cement with pigments to match the shade of tiles laid over and including 15mm thick screed bed or bedding layear in CM (1:6) in white cement with pigments complete all as specified and as directed by Enginee-in-charge.

Material and Labour for Marble tiles 30cmx20cmx20mm thick machine cut, bedded jointed and pointed with grey cement slurry Including and polishing type, shade and colour as approvd by GE, etc. set and jointed in neat cement slurry @3kg / Sqm and pointed in white cement with pigments to match the shade of tiles, in dado/skirting/vertical surface including 15mm thickness rendering in cement mortar ( 1:4) complete all as specified and as directed by Enginee-in-charge.

Material & Labour for kota stone 18mm - 20mm thick as in flooring with and including laid over 15 mm thick cement screed base in Cement Mortar in 1:4 laid and jointed with grey cement slurry @3kg / Sqm mixed with pigment to match the shade of kota stone including rubbing and mirror polishing complete all as specified and as directed by Engineer-in-charge.

Material & Labour for kota stone 18mm - 20mm thick as in riser of steps, skirting, dado and pillar with and including laid over 10 mm thick rendering in cement mortar 1:4 laid and jointed with grey cement slurry @3kg / Sqm mixed with pigment to match the shade of kota stone including rubbing and mirror polishing complete all as specified and as directed by Engineer-in-charge.

Material and labour 18mm - 20mm thick machine cut, granite duly factory grinding and polished (table rubbed and polished) of approved colour for counter sunk wash basin, plateform /cooking plateform , steps, jambs,pillars, window cills, , shelves, urinal partition and like ,laid and jointed with grey cement slurry @3kg / Sqm laid over with and including screed bed 15mm thick in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admiture of pigment to match with shade of granite stone slab including cutting as required including cleaning and extra polishing if required complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters of PVC door , wooden door shutter, wooden window shutter , Mild steel window and Mild steel ventilators (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed by Engineer-in- charge.

Taking down chowkhats or frames with shutters of PVC door ,wooden door shutter, wooden window shutter , Mild steel window and Mild steel ventilators (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 Sqm each complete all as specified and as directed by Engineer-in- charge.

Supply & fixing Factory made single extruded WPC ( Wood Polymer Composite ) Solid Door Frame /cupboard frame/ Chowkhat of Size 45mm x 70 mm comprising of virgin polymer of K value 58-60 (suspension grade ), Calcium Carbonate and nautral fibers ( Wood Powder / Rice husk / Wheat husk ) and non toxic additives (maximum toxcity index of 12 for 100 gms ) fabricated with miter joints after applying PVC Solvant cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg /cum and screw withdrawl strength of 2200 N (face ) & 1100 N (Edge) minimum Compressive strength of 58 N /sqmm modulus of elasticity 900 N/Sqmm and resisitence to spread of flame of class A category with property of being termite / borer proof , water moisture proof and fire retaident and fixed in position with and including MS hold Fast lugs / SS Dash Fastner of required dia and length with and including Supply & fixing (03 Nos Per Frame ) 100 mm long SS Butt Hinges with and making good with plastering/rendering etc. around the finished opening of the distrubed surface with Cement Mortar 1:4 complete all as specified and as directed by Engineer-in- charge.

Supply & fixing Factory made single extruded WPC ( Wood Polymer Composite ) Solid Plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (suspension grade ), Calcium Carbonate and nautral fibers ( Wood Powder / Rice husk / Wheat husk ) and non toxic additives (maximum toxcity index of 12 for 100 gms ) having minimum density of 650 kg /cum and screw withdrawl strength of 1800 N (face ) & 900 N (Edge) minimum Compressive strength of 50 N /sqmm modulus of elasticity 850N/Sqmm and resisitence to spread of flame of class A category with property of being termite / borer proof , water moisture proof and fire retardant and with and including Supply & Fixing of 02 Nos (per Leaf) SS 150mm long Tower Bolt with Stainlessd steel screws and including Supply & fixing of 02 Nos SS 150mm long handle with Stainlessd steel screws and 300 mm SS sliding door bolt with Stainlessd steel screws complete all specified and directed by Engineer -in-charge. Note:- The rate of 02 Nos. SS 150mm long Tower Bolt . 02 Nos. SS 150mm long handle and 300 mm SS sliding door bolt is included in this item and nothing shall be paid extra on this account.

Resecuring or easing & adjusting without taking down shutters of any description exceeding 1 Sqm but not exceeding 2.00 Sqm each complete all as specified and directed by Engineer-in- charge.

Material and labour for Providing and fixing aluminium work with Polyester powder coated aluminium ( minimum thickness of polyester powder coating 50 micron for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conformikng to IS:733 and IS :1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions i.e at top , bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth , rust free, straight, mitred and jointed mechanically wherever required including aluminium cleat angle, aluminium snap beading for glazing/ paneling , C.P. brass/ stainless steel screws, all complete all as specified and directed by Engineer-in-charge . Note :- (i) Weight of aluminium sections , aluminium cleat angles , aluminium butt hinges, aluminium handles , aluminium tower bolts , aluminium peg stays & aluminium snap beading shall be physically ascertained through a board of officers convened by GE and payment shall be made only after ascertaining the actual weight of aluminium at site. (ii) The rate of material and labour for providing the EPDM rubber, neoprene gasket , C.P. brass / stainless steel screws are included in this item and nothing shall be paid extra on this account. (iii) During considering the weight of aluminium sections , aluminium cleat angles , aluminium butt hinges, aluminium handles , aluminium tower bolts , aluminium peg stays & aluminium snap beading , the weight of EPDM rubber, neoprene gasket , C.P. brass/ stainless steel screws shall not be considered for measurments and payments. Only the weight of the aluminium sections , aluminium cleat angles, aluminium butt hinges, aluminium handles , aluminium tower bolts , aluminium peg stays & aluminium snap beading shall be considered and measurment and payment shall be made accourdingly. (iv) During the weight of aluminium sections , aluminium cleat angles , aluminium butt hinges, aluminium handles , aluminium tower bolts , aluminium peg stays & aluminium snap beading ,the weight of polyester powder coating 50 micron shall not be considered for weight but the rate of material and labour for providing polyester powder coating 50 micron is included in this item and nothing shall be paid extra on this account. (v) Glazing /Paneling and wire mesh shall be measured and paid seperately. (v)The board shall be duly countersigned by GE shall enclosed with Final Bill .

Supply & fixing 4.8 mm thick, sheet glass ordinary quality not exceeding 0.50 sqm in each pane complete all as specified and as directed by Engineer-in- charge.

Supply and fixing solar control film 25mm micron reflective type (greater sun control or Equivalent) complete all as specified and as directed by Engineer-in- charge

Supply & fixing stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tack or galvanised steel wire staples complete all as specified & directed by Engineer-in- charge.

Supply & fixing aluminium (Extruded section body) body door closer hydraulically regulated, designation No 3, universal type suitable for door shutter of 851 to 1000mm in width and weight between 61 to 80 Kg, ISI marked complete all as specified & directed by Engineer-in-charge.

Supply & fixing Mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified & directed by Engineer-in-charge.

Dismantling Wall and Ceilling Board (fibre, pulp, Insulation,etc) or Insulation boards/slabs/ blankets any thickness including cover fillets fixed in any position with nails fixed with screws complete all as specified and as directed by Engineer-in- Charge.

Supply and fixing GI snap Grid frame work of size of grid 605mm x 605mm for false ceiling including necessary notching and prepared holes, the snap grid shall consist of anodised aluminium main Tee of size 36.5mm x 25mm x 1.4mm weighing 0.24 Kg/Rm, cross and intermediate Tee of size 23.5mm x 26.4mm x 1.4mm weighing 0.191kg/RM. The main and cross Tee shall be Joined at junction with steel screws or MS bolt, nuts and washers, the snap grid (main/cross tee section) shall be supported at the ends all along the wall with anodised aluminium angle of size 35mm x 25mm x 2mm weighing 0.36kg/RM fixed to wall with suitable arrangement and duly suspended with 4mm GI wire hangers(up to 1200mm length) adjusting level fixed to roof slab by means of ceiling cleats made of GI flat 40mm x 3mm size , 60mm long and expansion hold fasteners 12.5mm dia 40mm long, with and including providing 12mm thick gyupsum board as approved by GE in grid fixed in false ceiling grid made of aluminium as per manufacturer's instruction complete all as specified and as directed by Engineer-in- Charge. Note: The rate of 12mm thick gypsum board is included in this item and nothing shall be paid extra on this account.

Material and labour for solid PVC Wall lining consisting of 5mm thick wood Grain printed PVC Sheet Inclusive of solvent cement and fixing at site on PVC Frame as per specification,with and including for 5mm thick PVC Sheet fillet of width 35mm for Wall paneling Inclusive of fixing on to wall to make PVC Frame as per specification, complete all as specified and as directed by Engineer-in- charge.

Material and labour for Double layer POP( Plaster of Paris) False ceiling of any Pattern and design Including Nesessary GI Frame work, Mesh, Including Projection and cutting for ceiling light as per Requirement, Design and pattern shall be approved by GE/AGE, complete all as specified and as directed by Engineer-in- charge.

Demolition of cement concrete un- reinforced of any description and in any position not otherwise specifically provided for and including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge

Material and Labour 75mm thick PCC 1: 3: 6 type C-2 ( using 40mm graded stone aggregate ) in plinth protection, including finishing the surface even and smooth without using extra cement.by Engineer-in-charge.

Demolition of cement concrete reinforced of any discription and in any position, including reinforcement cut as required to facilitate and including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge. Note:The weight of scrap iron for schedule of credit shall be ascertain by BOO as ordered by GE.The copy of BOO duly countersinged by GE shall be enclosed with final Bill.

Material and labour for RCC 1:2:4, Type-B-1, using 20 mm graded stone aggregates (Nominal Mix) as in chajjas complete all as specified and as directed by Engineer-in-charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Demolition of brick work masonry, built in cement mortar including all quoins, arches, pillars, etc, complete all as specified and as directed by Engineer-in- charge.

Material and Labour Brick work with sub class ‘B’ burnt clay old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in- charge.

Material and labour for Brick work with sub class ‘B’ burnt clay old size bricks, straight or curved on plan to any radius in half brick walls built in Cement mortar 1:4 complete all as specified and as directed by Engineer-in-charge.

Supply & fixing 110 mm bore of pipe PVC (SWR) type B ring fit pipes single socket in any length with Stack clamps as shown in BTD Drg No. 916 sheet 1/4 to 4/4 and BTD-917 sheet sheet 1/1 of stays to wall at a distance of 100-120mm away from walls complete all as specified and as directed by Engineer-in- charge including Taking down old AC eaves gutters and rain water pipes ( of any size and pattern) including all fittings, compete all as specified and as directed by Engineer - in-charge.

Supply & fixing 110 mm bore, PVC (SWR) fittings Type -B such as bends, tee, 'Y' etc ; fixed to PVC pipes, complete all as specified and as directed by Engineer - in-charge.

Supply & fixing 110 mm bore of pipe PVC (SWR) type B ring fit pipes single socket in any length with Stack clamps as shown in BTD Drg No. 916 sheet 1/4 to 4/4 and BTD-917 sheet sheet 1/1 laid in floor , trenches etc complete all as specified and as directed by Engineer-in- charge including Taking down old AC eaves gutters and rain water pipes ( of any size and pattern) including all fittings, compete all as specified and as directed by Engineer - in-charge.

Supply & Fixing in replacement of vitreous China squatting pan of Orrissa pattern of approved make of size 580 mm x 440 mm x 260 mm white with integral foot rests including connection to trap and to flushing pipe including lime concrete bedding and connection to antisyphonage pipe etc including making good to floor complete all as specified and as directed by Engineer-in- charge.

Supply and fixing in replacement 10 litres capacity PVC valveless syphonic action type low level flushing cistern white with inlet, ball valve, float, handle including brackets and 32mm dia PVC flush pipe complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repairs 600 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge.

Supply & fixing of 600 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge.

Supply & fixing in replacement of vitreous china wash down water closet pan (pedestal pattern, EWC) P Trap white clour , including connection to drain etc., including plastic water closet seat with cover (white clour) closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device including stainless steel chromium plated jet spray with 01 mtr long PVC pipe with CP connector and necessary nut bolts and with necessary CP screws and plug for fixing WC complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in replacement of wash hand basin oval type of size not less than 550mm x 400 mm , table top fancy including 32mm dia Chromium plated waste coupling, waste pipe, PVC connection and all necessary fittings vitrous China white flat back including brackets, waste coupling & PVC Waste Pipe of 32mm dia etc complete all as specified and as directed by Engineer-in-charge .

Supply & fixing in replacement of vitreous china urinal of size 410mm x 380mm x 950mm, half stall type white, with grating and union for discharge pipe including CP urinal spreader and CP connection and waste pipe complete all as specified and Engineer-in-Charge.

Supply and fixing in replacement 5 to 6mm thick mirror including ingraved any pattern, or with wooden beading of any size fixed to wall with CP Screws with top cap and all complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 20 mm bore CPVC pipe SDR 11and plain CPVC SDR 11 fitting with all fitting and fixed to walls & ceilings or laid in floors, including taking down unservicable existing GI tubing of 20mm bore and fittings complete complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing 25 mm bore CPVC pipe SDR 11and plain CPVC SDR 11 fitting with all fitting and fixed to walls & ceilings or laid in floors, including taking down unservicable existing GI tubing of 25mm bore and fittings complete complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing 32 mm bore CPVC pipe SDR 11and plain CPVC SDR 11 fitting with all fitting and fixed to walls & ceilings or laid in floors, including taking down unservicable existing GI tubing of 32mm bore and fittings complete complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement 15mm bore Bib tap long body cast copper alloy, chromium plated , fancy type, with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

Supply & fixing in replacement of Stop valve / angle valve , cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule for 15 mm bore of pipe complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in replacement of 15mm bore swan neck Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr In Charge

Supply & fixing in replacement of 15mm bore, brass Chromium Plated central hole basin mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and as directed by Engineer-in- charge.

Supply and fixing in replacement sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x460mm bowl size 410mm x 330mm x160mm complete all as specified and as directed by Engineer-in-charge.

Supply & fixing in replacement of brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and as directed by Engineer-in-charge.

Supply & fixing in replacement Rotational Moulded Polyethylene water storage tank ISI Marked of capacity 1000 litres (cylindrical vertical, with closed top), hoisted and fixed in position including making inlet and out let connection complete all as specified and as directed by Engineer-in-charge. (Note :- Ball valve and gate valve shall be measured & paid separately under appropriate items of Schedule 'A' BoQ.)

Supply and Fixing in replacement Ball valve high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe of size 20 mm bore (minimum weight 20mm-210 gram) complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in replacement of Gun metal, globe or gate valve (ISI marked), brass cast copper alloy, with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing in replacement 25mm dia Stainless steel curtain rod with bracket and knobs at both ends as per site requirement including taking down old existing PVC Conduit pipes with accessories complete all as specified and directed by Engineer-in-charge.

Supply and Fixing venetian blinds vertical sabine of size 100mm conforming to relevant IS complete with all accessories colour and shade as approved by GE with Hanging device for Operation, complete all as specified and directed by Engineer-in-charge.

Material and Labour for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed by Engineer-in-charge.

Material and Labour for preparation of old painted steel surfaces of any description not otherwise described over 10 cm width & girth by applying one coat of synthetic enamel paint of approved tint complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement of 18/20mm thick block Board(grade2, Interior grade Quality), commercial Type fixed with Screws /nails/ Fevicol including cutting and made to shape as required Including Second Class soft wood Pplain fillets Square, Rectangular or Triangular in sectio, Clean swan fixed with Screw/nails etc complete all as specified & directed by Engineer-in- charge.

Material and Labour for preparation of New wooden surfaces of any description not otherwise described over 10 cm width & girth by applying Two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-charge.

Material and Labour for preparation of old painted wooden surfaces of any description not otherwise described over 10 cm width & girth by applying one coat of synthetic enamel paint of approved tint complete all as specified and directed by Engineer-in-charge.

Demolition Stone slabs and tiles of any description or thickness in floors, aprons etc Laid dry or bedded and pointed in any mortar complete all as specified and as directed by Engineer-in-Charge.

Material and labour Bull nosed chequered cement concrete tiles 20cm x 20cm x 25mm thick, set jointed and pointed in neat cement slurry @ 3.00kg /per sqm as in floors, and no Pigment laid over with and including 20mm thick screed bed in cement mortar 1:4 complete all as specified and as directed by the Engineer-in- charge.

Taking down carefully copper /aluminium point wiring conceald/ battern (light, fan, socket or power point ) complete including fitting such as hylem , sheet switches, ceiling rose, pendent holder sockets, regulator except concealed conduit and sunken boxes etc. complete all as specified and directed by Engineer-in-charge. Note:1.The weight of aluminium scrap and copper scrap for schedule of credit shall be ascertain by BOO as ordered by GE.The copy of BOO duly countersinged by GE shall be enclosed with final Bill.(ii) The rate of cutting chases (as required) and making good surfaces to match with adjoining surface shall be measured and paid seperately under serial item no 82.00,83.00,84.00,85.00 & 86.00 of BoQ.

Material and labour for concealed Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), in PVC conduit complete with 2.5 sqmm (nominal cross section area ) FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked ) drawn through with and including PVC rigid conduit 20mm dia ( heavy duty ) ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories) with all fittings and all accessories i.e pipe bend pipe hook, elbow,junction box, pressed steel powder coated sunken box of suitable size (min 60mm deep, suitable length and 1.2mm thick ) and flush fixed with cement mortar 1:4 , 3mm thick bakelite plastic laminated sheet for mounting with frame and top cover for switches and socket ,fan regulator, for light/fan point controlled by one switch, top cover fixed with brass screws & cup washers including provn of 2.5 sqmm FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc with and including cutting chases (as required) and making good surfaces to match with adjoining surface complete all as specified and as directed by Engineer-in- charge .Note for serial item no.82.00,83.00,84.00,85.00 & 86.00 : (i) switches , sockets 5 /6 Amp , sockets 15 /16 Amp & fan regulator shall be measured and paid seperately under respective items of Schedule'A' BoQ.(ii) The rate of cutting chases (as required) and making good surfaces to match with adjoining surface is included in this item and nothing shall be paid extra on this account. (iii) On RCC roof / ceiling PVC conduit shall be provided on surface with proper fixing clips as directed by Engineer-in- Charge.The rate of this element is included in this item and nothing shall be paid extra on this account.

All as per item No 82.00 here- in -before but for one Socket outlet multipurpose 2 in 1, 5 Pin, 5/6 Amp, on same board complete all as specified and as directed by Engineer-in- charge.

All as per item No 82.00 here- in -before but for one Socket outlet multipurpose 2 in 1, 5 Pin, 5/6 Amp, on independent board complete all as specified and as directed by Engineer-in- charge.

All as per item No 82.00 here- in -before but for one Socket outlet multipurpose 2 in 1, 6 Pin, 15/16 Amp, on independent board controlled by 15 Amp switch complete all as specified directed by engineer-in-charge.

Supply and fixing Socket outlet 5 pin, 5 Amp, Flush type complete all as specified and as directed by Engineer-in- charge.

Supply and Fixing switch piano flush type 5 Amp, ISI marked 240V AC, single pole, one way complete all as specified and as directed by Engineer-in- charge

Supply & fixing switch piano, flush button single pole one way 15 Amp complete all as specified and as directed by Engineer-in- charge

Supply & fixing Socket outlet multipurpose 6 Pin, 15 Amp, 240 volt Multi purpose flush type complete all as directed and as directed by Engineer-in- charge

Supply & fixing ceiling rose surface type polycarbonate isolated body two to three terminal , tp line series 20x50mm, 6 amps three terminal complete all as specified and as directed by Engineer-in- charge.

Material and labour in replacement Sub main wiring complete with two single core 6 sqmm,1100 volts grade, PVC insulated, multi stranded copper conductor cable FRLSH with and including single core 6 sqmm,1100 volts grade, PVC insulated, multi stranded copper conductor cable FRLSH for earth wire in existing PVC concealed conduit (Colour code phase-Red, Neutral-black and Earth as Green) complete all as specified and directed by Engineer-in-charge. Notes:- (a) Three single core 6 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade shall be measured as one length.

Material and labour in replacement Sub main wiring complete with two single core 4.00 sqmm,1100 volts grade, PVC insulated, multi stranded copper conductor cable FRLSH with and including single core 4sqmm,1100 volts grade, PVC insulated, multi stranded copper conductor cable FRLSH for earth wire in existing PVC concealed conduit (Colour code phase-Red, Neutral-black and Earth as Green) complete all as specified and directed by Engineer-in-charge. Notes:- (a) Three single core 4 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade shall be measured as one length.

Supply and fixing in replacement (concealed flush to wall) factory made DB (made out of CRCA sheet not less than 1.2mm thick, fitted with DIN channel neutral link and 200 Amp rated bus bar) SPN, 12 Way 240V, suitable for mounting MCB/Isolator etc, conforming to IS-13032, DB shall be semi glosy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process to ensure smooth finish and protection against corrosion atmosphere. The DB shall be double door type with hinged door with locking arrangement, the DBs shall be same make as MCBs, DB shall be provided with level marking indicating the incoming and outgoing circuits on always as specified. The DBs shall be of IP-54 protection class, and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge. Note :- MCB/Isolator etc shall be measured and paid separately under appropriate item of BOQ.

Supply and Fixing in replacement Sheet metal enclousers made out of CRCA mild steel sheet not less than 1.2mm thick,, IP-54 protection, flush mounted for metal door, powder coated DB VTPN 4 way, 415 V AC with 200 Amps rated bus bar, Double door, dust and vermin proof suitable for incorporation of Incoming MCCB and outgoing MCB SP/TP and earth & neutral bus bar etc complete all as specified and as directed by Engineer-in- charge.Note: MCB/ Isolators shall be measured and paid seperately under appropriate item of BOQ.

Supply and Fixing MCCB 125 Amps 25 KA , 4 pole, 415 Volt fixed thermal and fixed maganatic setting complete all as specified and directed by Engr-in-Charge.

Supply & fixing in MCB SPN 32 Amp suitable for 240 volt, 10 KA complete complete all as specified and as directed directed by Engineer-in- charge.

Supplying and fixing MCB SPN suitable for 240 volts AC supply 40/50 Amps, complete all as specified and directed by Engineer-in-charge.

Supplying and fixing MCB SP suitable for 240 volts AC supply 5 to 32 Amps, SP rupturing capacity not less than 10KA, C Curve complete all as specified and directed by Engineer-in-charge.

Supply & fixing in replacement New generation energy saving, wall mounted 20watt (4.00 feet long) LED tube light batten fittings with extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver 20watt LED power factor > 0.95, 100 lumen /watt duly fitted on PVC Square block ,5700K with rod 20 watt , 230volts ,50Hz complete all as per manufacturer's instructions, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to tube fitting, complete fitting with all accessories complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in replacement LED Street light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrossion resistant complete with IP 65/66 protection with and including connection with copper cable of suitable size from ceiling rose to fitting complete all as manufacturer's instructions ,as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement Ceiling type round shape 6 watt 220 volts AC surface type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling complete all as per manufacturer's instructions and connection with flexible twin core copper cable of size 23/.00076 from ceiling rose to fitting complete all as specified and as directed by Engineer-in- charge.

Supply and Fixing in replacement LED Panel Light fitting recessed mounted,square shaped of size 600mm x 600mm , 36 (±10%) watt, efficacy not less than 100 lumen/watt , extruded Aluminium/polycarbonate, PC diffusor and inbuilt driver complete as per manufacturer's instructions with and including connection with flexible twin core copper cable of size 23/.00076 from ceiling rose to fitting complete all as specified and as directed by Engineer-in- charge.

Material and Labour in replacement earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6 mm thick burried directly in ground to depth of pit not less than 2.25 m below normal ground level with top edge of the plate not less than 1.5 m below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal / coal dust and common salt filling in alternate layers and connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel including GI protection pipe 15mm dia light grade upto the extent of 7.5 metre and connecting to earthing test point, main switch board including GI pipe 20 mm dia light grade for watering, MS funnel and bringing out the watering pipe upto 30 cm above the normal ground level plugged at top including all fitting including PCC earth pit with PCC 1:2:4 type B-1 using 20mm graded stone aggregate and RCC pit cover including necessary earthwork and excavation in any type of soil complete all as specified as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note:- (i) Earth continuity of GI wire 4 mm including protection pipe up to 7.5 mtrs from earth electrode will be included in unit rate, complete all as specified and directed. (ii) The rate of earth work in soft/loose soil i.e. excavation, returing filling and removal, form work is included in this item and nothing shall be paid extra on this account. (iii) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (iv) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.

Supply & Fixing in replacement of Ceiling fan of 1200mm sweep complete with blades, down rods, including Remote Control and accessories, 230 Volts, single phase, 50 Hz, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current (BLDC) motor connecting up complete with and including three core flexible PVC insulated multi stranded copper conductor cable of suitable size from ceiling rose / connector, including extra GI / MS pipe down rod, as per site requirement , with and including serial number of fan as issued by Engineer-in-charge and GE office name with red colour permaent marker complete all as specified and directed by Engineer-in-Charge. Note: Old unservicable ceiling fan shall be deposited in the store yard of AGE E/M GE North at his own arrangment as directed by Engineer-in-charge and nothing shall be paid extra on this account.

Supply & Fixing wall mounted high speed fand 2100 RPM 230 volt complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Making hole for 300mm dia exhaust fan of suitable shape & size into or through brick walls at Ground/First/Second Floor Including plstering for Making Good to the Original surfaces of any description distrubed including painting/ distember matching with existing Colour, Note rates are deems to be including charges of any type of T&P Insurance of staff deployed at site

Supply & Fixing Exhaust fan (Heavy duty) steel body, AC, Single phase 230 volts,50HZ,900 RPM ,300 mm sweep BEE, 5 star rated a with blades and frame including new mosquito stainless steel wire mesh of guage 0.36mm with suitable wooden frame protection against birds etc. mounted in suitable opening arrangmement in wall and electric connection with and including three core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm drawn in flexible PVC Conduit and hanging on wall with 04 Nos. steel fastners 10mm dia 100mm long with and including serial number of fan as issued by Engineer-in-charge and GE office name with red colour permaent marker complete all as specified and directed by Engineer-in- charge.

Supply and Fixing water heater (Geyser) Auto restrat and safety measures type electrical operated 230/240 Volts 25 ltr capacity, BEE 5 star rated complete with all safety equipment and accessories such as safety valve, thermostat, plug top, etc. required for proper functionality & including electric/earth connections and carrying out grounting & complete installations with mounting bolts,nuts including testing after installation complete complete all as specified & directed by Engineer-in- Charge.

Supply & fixing of 4 Nos rawl plug of suitable size (4" -6") Nuts & Bolts, grouting work in RCC/Brick Wall, cemented works labour charges for cutting to existing GI Pipe line of Size 15mm dia in position for Insertion of Tee or Branch connection Jointing complete with necessary GI Fittings, Plumbing all as per site requirement. complete all as specified and as directed directed by Engineer-in- charge.

Supply and fixing Single Pole and Neutral enclosure with a two pin and earth plug and socket complete with and including one MCB single pole of capacity 25 Amps,'C' curve,10KA , 240 volts complete all as specified and directed by Engineer-in-Charge.Note: The rate of one MCB single pole of capacity 25 Amps,'C' curve, 10KA, 240 volts is included in this item and nothing shall be paid extra on this account.

Supply and fixing in replacement of Galvanised Iron pipe medium Grade 15mm bore with all Fittings laid in floors or trenches complete all as specified and directed by Engineer-in- Charge,

Supply & fixing stop valve cast copper alloy, chromium plated ,screwed both ends for iron pipe of dia 15 mm complete all as specified and directed,all as specified & directed. ISI Marked

Supply and fixing 15mm bore Bib tap cast copper alloy, chromium plated , with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

Material and Labour for cutting to existing GI Pipe of size 20mm/25mm bore in position for addition/alteration or insertion of Tee Banch connection complete with cutting, threading and jointing/fixing incuding GI fittings as per site requirement complete all as specified and as directed by Engineer-in - charge. Note : The rate of GI fittings of required size as per site requirement as directed by Engineer-in-charge is included in this item and nothing shall be paid extra on this account.

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender from total amount of Schedule 'A'/BOQ

rkkataria and sons (BID ID -3334062)

R K GOYAL & COMPANY (BID ID -3334191)

M/s Verma Construction Company (BID ID -3329493)

KULWANT RAI (BID ID -3333669)

RINKU BROTHERS (BID ID -3334248)

M/S VERMA BUILDERS & DEVELOPERS (BID ID -3330755)

M/s Vandana Builders (BID ID -3333961)