Construction of Cold Store at potato development station Dalang GP Gondhla Tehsil Keylong District Lahaul Spiti HP

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. work/ jumper work 50% each.

a) Foundations, footings, bases of columns, etc. for mass concrete

b) Columns, Pillars, Piers, Abutments, Posts and Struts

c) Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand): 10 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand): 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position machine batched and machine mixed design mix M-25 ( M-Twenty five) grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.(Note :- Cement content considered in this item is @ 330 kg/cum ( Three hundred thirty three Kilogramme/cubic). Excess/ less cement used as per design mix is payable/recoverable separately) All works upto plinth level

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing flooring of approved colour on steel frame work with 50mm thick PUF floor panel with adhesive, screws etc. completeas per standard sizes fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make, Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick of 8 to 10 gauge of length varying from 25 to 45 mm. Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately).

Providing and fixing internal and external wall panels of approved colour on steel frame work with 80mm thick PUF wall pane with (Inner Flashing/Outer Flashing/ U channel) with Silicon & Pop Rivet & gittil as per standard sizes fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make, Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick of 8 to 10 gauge of length varying from 25 to 45 mm. Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately).

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse

Coursed rubble masonry (first sort) with hard stone in foundation and plinth with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

Providing and fixing ball bearing for rolling shutters.

Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality including fastners, window shutter double glass panes 6.00mm thick, wire mesh/bug mesh, sliding door bolt/lock handle, handles, tower bolt, hooks & eyes of approved size and silicon sealant all complete as per approved drawing & direction of Engineer-in-Charge.

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality including fastners, door shutter, double glass panes 6.00mm thick in fixed glaze door, wire mesh/bug mesh, sliding door bolt/lock handle, handles, tower bolt, hooks & eyes of approved size and silicon sealant all complete all complete as per approved drawing & direction of Engineer-in- Charge.

Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing Pre-laminated medium density fibre board IS: 14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-I(exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately). Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade - I MDF Board 25 mm thick confirming to IS:14587

Providing and fixing fixing 25mm thick pre-laminated medium density fibre board exterior grade ( Grade-I) IS:14587:1998 marked with one side decorative and other side balancing lamination for cupboard shutters edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand including ISI marked nickel plated bright finishing M.S. piano hinges conforming to IS:3818 marked with necessary screw etc all complete.

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. Triple strip vertical type

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.

Providing and fixing ISI marked C.P. soft closing hinges with nuts and screws etc. complete : 150 mm

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 50 mm

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25mm thick.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing pre painted troughed profile colour coated 0.60 mm thick high tensile steel ZINSALUME ( Zinc-Aluminium alloy coating sheet) roofing with trapezodal corrugation of maximuim pitch 190 c/c and minimum depth of 30mm with return leg & sealent grove for proper side overlap single sheet to be provided upto 10 m drom ridge to eaves for providing overlap with fixing of sheets with self drilling and self tapping galvanized or zinc alloy coated fasteners of size 5.5mm (dia.) abd 55mm(length) with EPDm seal test certifiacte and over 20 year warranty against colour fading with other necessary fitting of steel sheet roof.

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 1.60 mm thick with zinc coating not less than 350 gm/m²

Providing and fixing 15 cm wide, 45 cm overall semicircular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.80 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

110 mm bend

110 mm Shoe

Providing and fixing prepainted stainless steel snow guard with necessary screw, fitting etc. complete. Colour should be same as that of roof colour.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Making plinth protection 50mm thick of cement concreten1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and fixing Refrigeration Machine 7HPMT of approved brand with minimum five year warrenty along with Matching Evaporator with installation of Refrigeration Machine ( Each room Electrical panel with controller, Contactors Schneider with electrical controls, Wireleep, poliycab cap , Copper pipe Accessories, Ball valve, Drier, Site Glass & Gas , pressure testing etc) complete including haulauge, loading and unloading etc. complete.

Supplying, laying, fixing, and termination of approximately 70 meters of XLPE insulated, armoured copper cable (minimum 4 core, 10 sqmm) from main distribution board to 4 nos. cold storage machines (compressor, evaporator, etc.) via one industrial-type MCB/RCB distribution box (TPN, 10kA with RCCB/RCBO) for machinery, and to the office area via a separate MCB/RCB distribution box (SPN, 10kA, with RCCB/RCBO); including all power/control wiring, supply and installation at each machinery point of 4 nos. heavy-duty industrial 3-phase ON/OFF isolator switches (63A/100A as needed), each with interlocked industrial-grade socket and enclosure, supply and installation of 1 no. office modular switch board with 4 switches, 1 fan regulator and 1 socket point 16Amp. with faceplate and wiring, all cable trays/conduits/supports for safe cable routing, cable glands, lugs, earthing wires and connections to earth pit, complete labelling and circuit identification, safety marking, full testing and commissioning. All equipment and materials to be of approved make (ISI/IEC marked) and suitable for humid/cold storage environment. Excludes supply/installation of cold storage machinery. Work to be executed as directed by Engineer-in-Charge and in accordance with IS/IEC standards.

Supply, installation, testing, and commissioning of 63kVA, 11kV/0.433kV, 3-phase oil-immersed naturally cooled distribution transformer, conforming to IS: 1180 (Part-1), with energy efficiency Level-1/Level-2 as per relevant BIS standards complete with all components. Work to be executed as directed by Engineer-in-Charge and in accordance with IS/IEC standards.