Construction of Community Hall and Boundary wall in various villages in Block Kahnuwan District Gurdaspur under Scheme MP LAD for the year 2025-26

Construction of Community Hall at village Chask Sharif Excavation in Soil (any type) using Hydraulic Excavator CK 90 with hydraulic excavator of 0.9 cum bucket capacity including cutting, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, including all lifts and combined lead upto 30m.

Cement Concrete 1:6:12 with stone ballast 40mm gague mixing by mechnical means using concrete mixer volumetric type

First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth

Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering)

Centring and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth.

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure.

Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 550 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate of RCC including binding, bending and placing in position complete

First class burnt brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working ressure 4.00 kgf / cm²) conforming to IS : 4985, including jointing with seal ring (i) Single socketed pipes. (CSR 13.74a) U-PVC pipes (working pressure 4.00 kgf. / sqcm) Single socketed pipe 110 mm dia.

Providing and fixing 110 mm dia. U.P.V.C bendfor Rain water pipe as per IS:14735 includingjointing complete as per pecifications and to theentire satisfaction of Engineer- in- charge.UPVC 110 mm bend

Providing and fixing 110 mm dia. U.P.V.C Coupling/Sockete for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. UPVC 110 mm bend

Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16.

Bottom Khurra on ground 1.2m. x 0.6m. consisting of brick on-edge laid in cement mortar 1:3 over 75mm cement concrete 1:8:16 including 12.5m.m. thick cement plaster 1:3.

Providing and fixing in position SS Grating with frame of approved make (to the approval of engineer in charge) complete in all respects.

Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar upto 40% taking outside the premises in 15 cm layers incluidng ramming, watering and consolidated all lead.

Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar upto 40% excavated from foundation and taken only from outside the building plinth in 15 cm layers including ramming, watering and consolidating lead upto 30 metres.

Base course of floor consisting of 100mm thick cement concrete 1:8:16 with stone Aggreegates 40mm Gauge and 100mm Fine sand filling using mechanical mixer for mixing of material.

Conglomerate floor 50mm thick cement concrete topping 1:2:4 using mechanical mixer for mixing of material

Supplying Pressed steel sheet frames (chowkhat) consisting of 18gauge (1.25 mm thick steel sheet of the specified section, including iron lugs (hold fast) iron hinges conforming to PWD specification including bolts for fixing stops lock notch provision for receiving tower bolts and finished with 1 primer coat approved quality, fixed in position excluding the cost of cement concrete 1:3:6 for fillings in the frame and cement concrete 1:2:4 for lugs complete Doors and windows frame of size 118mm x 60mm with 40 mm wide single rebate weighing 3.43 kg per meter.

Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position (Code : II Revision IS-2191 Part-I) 1973. 35mm thick

Supplying openable steel windows, of standard rolled steel Z sections, joints mitered and Electrically flash-welded, with iron fittings including necessary iron handles, Peg-stay catchers bolts, iron plugs and pressed steel projected hinges and glazing clips, complete (Excluding glazing ) and finished with two coats of ready mixed paint red lead non setting primer

Cost of Aluminium fittings complete for doors, windows such as tower bolts, handless and screw etc. for these fittings (Excluding sliding bolt) For shutter area above 0.50 sqm

12.5 mm thick cement plaster 1:4. CSR 15.9 (inner Side)

20 mm thick cement plaster 1:5

Finishing walls with water soluble exterior cement based paint such as snowcem, robbiacem etc. two or more coats to give an even shade

White wash two coat

Applying priming coat with metal primer on new steel or iron work including preparation of surface.

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade.

RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches and 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½" deep for walls and CI 3" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc. including the cost of above material, cutting and filling up of chases:- Wiring fan point (With fan box)

Wiring light point

Wiring 6Amp. wall socket point

PVC INSULATED FR COPPER CONDUCTOR CABLES: Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- Overall size 1.50sq.mm (Un-sheathed)

PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, MS saddle clamps and other petty materials etc., as per PWD General Specifications:- Heavy Gauge PVC Conduit Pipe 25mm dia. (Flushed)

MINIATURE CIRCUIT BREAKERS/ RCBO's/ RCCB's: Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:- MCB Single Pole 6-32amp. (10kA, Curve-C)

Supply & Erection of Durable LED Batten with Polycarbonate Housing 20 Watt Make: Crompton Input AC Frequency Hz +- 3% complete along with erection of the same with, testing, in all Respect. complete in all respect as per approved /desired by the engineer in charge of work at site . The Certification and Specification of The Led fitting should be as approved by of O/o Advisior( Technical) Govt. of Punjab Letter No: AT/2021/GL/1410-1422 Dated 16-05-2021.Make : Crompton Model : LCTLN-20-CDL , Phillips item BN021CLED22 PSU CW GR, Make: Havell's Item Code: LUMILINEBS20WLED865SPCWH/Halonix/ Wipro.

Supply and erection of Ceiling Fan 1200mm (48") with double bearing including flexible wire & petty material etc. for connection and testing. Complete in all respects as approved and desired by the Engineer in-charge at Site: Make: Crompton High speed 5 Star Opal White/ Havell's VELOCITY-HS, Orient -New Breeze, Bajaj- SPEEDSTER

Consruction of Boundary wall at Village Chibb Earth work in excavation in foundations, trenches etc.in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation

Cement Concrete 1:6:12 with 40mm gauge stone aggregate. mixing by mechanical means using concrete mixer volumetric type

First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth.

Centering and shuttering for sides and soffits of beam, beams, launching girders, bressumers, lintels.

Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 550 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate of RCC including binding, bending and placing in position complete

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth.

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure.

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level.

12.5 mm thick cement plaster 1:4

20 mm thich Cement Plaster in two coat 1:4

Cement concrete 1:2:4 with stone Ballast or Shingle for Toping mixing by mechanical means using concrete mixer volumetric type

Finishing walls with exterior decorative cement based paint such as snowcem, robbiacem etc. two or more coats to give an even shade

Consruction of Boundary wall at Village Nanowal Kalan Earth work in excavation in foundations, trenches etc.in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation

Cement Concrete 1:6:12 with 40mm gauge stone aggregate. mixing by mechanical means using concrete mixer volumetric type

First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth.

Centering and shuttering for sides and soffits of beam, beams, launching girders, bressumers, lintels.

Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 550 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate of RCC including binding, bending and placing in position complete

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth.

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure.

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level.

12.5 mm thick cement plaster 1:4

20 mm thich Cement Plaster in two coat 1:4

Cement concrete 1:2:4 with stone Ballast or Shingle for Toping mixing by mechanical means using concrete mixer volumetric type

Finishing walls with exterior decorative cement based paint such as snowcem, robbiacem etc. two or more coats to give an even shade

Consruction of Boundary wall at Village Fattu Barkat Earth work in excavation in foundations, trenches etc.in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation

Cement Concrete 1:6:12 with 40mm gauge stone aggregate. mixing by mechanical means using concrete mixer volumetric type

First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth.

Centering and shuttering for sides and soffits of beam, beams, launching girders, bressumers, lintels.

Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 550 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate of RCC including binding, bending and placing in position complete

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth.

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure.

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level.

12.5 mm thick cement plaster 1:4

20 mm thich Cement Plaster in two coat 1:4

Cement concrete 1:2:4 with stone Ballast or Shingle for Toping mixing by mechanical means using concrete mixer volumetric type

Finishing walls with exterior decorative cement based paint such as snowcem, robbiacem etc. two or more coats to give an even shade

Please Enable Macros to View BoQ information