ADDITION AND ALTERATION TO BLDG No. 2 A AND 2 C AT RA LINES OF JL WING, IMPROVEMENT OF TRAINING INFRASTRUCTURE AT COMMANDO TRG AREA, SPECIAL REPAIRS TO BLDG No. 15 A AND SUMP WELL AT NAGZEERA PUMP HOUSE AND PROVN OF 2 TOILET BLOCKS AND ALLIED WORKS

Amount

Demolition of plain cement concrete in ground floors and pavings n. exc. 15cm thick, below or above GL all as specified and directed.

Demolition of PCC solid block masonry built in cement mortar pillars, etc. in any position below or above ground level all as specified and directed.

Dismantling timber scantlings 40 sq.cm and over in section, in any position, in un-framed work all as specified and directed.

Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section all as specified and directed.

Dismantling boarding of any description fixed in any position with nails all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area n exc 1.5 Sqm each all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

Dismantling wrought iron or mild steel work of any description and in any position not otherwise provided for all as specified and directed.

Dismantling of single layer Mangalore pattern or similar tiles in roofing bedded in lime or cement mortar all as specified and directed.

Dismantling of plain or corrugated steel sheets of any gauge and thickness, in roof coverings, valleys, gutters, etc. all as specififed and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

Dismantling wall or ceiling boards or insulation boards/ slabs of any thickness including cover fillets all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing, rubbish off the premises all as specified and directed.

Taking down cement plaster on brick or stone wall or ceiling concrete etc. including racking out joints hacking for key scrubbing down with water etc., all as specified and directed.

Hacking out old broken glass of any thickness/ size/ quality/ description from wooden frames, glazed with putty or fixed with beads all as specified and directed.

Surface excavation n. exc. 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in soft/ loose soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in hard/dense soil all as specified and directed.

Excavation in post holes n.exc 0.5 cum in hard/ dense soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm watering and removing surplus soil to a distance n.exc 50 m and making good surface all as specified

Returning filling in including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for hard core with broken stone or boulders of gauge n.exc 63mm, deposited, spread, levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces all as specified and directed.

M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for plain cement concrete 1:4:8 type D2, using 40mm graded stone aggregate in foundation, filling, mass concrete, levelling courses and sub bases all as specified and directed.

M&L for plain cement concrete 1:3:6 type C2, using 40mm graded stone aggregate in foundation, filling, mass concrete, levelling courses and sub bases all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10cm width, blocks cast in PCC 1:3:6 type C1, using 20mm graded stone aggregate, set in CM 1:6 complete all as specified and directed.

M&L plain cement concrete 1:2:4, type B0, using 12.5mm graded stone aggregate as in coping, bed blocks, benching in channels, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

M&L for plain cement concrete 1:3:6 type C1, using 20mm graded stone aggregate in drains, copings, etc. including necessary form wok and moulds all as specified and directed.

M&L for extra for forming fair finished drain or channel of 25cm inner girth in cement concrete using extra cement including forms moulds mitred / stopped end etc. all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4, type B-0, using 12.5mm graded stone aggregate mixed with water proofing compond as in damp proof course to horizontal or vertical surfaces including use of necessary form work all as specified and directed. Note: Water proofig compound shall be measured and paid separately.

M&L for providing precast cement concrete 1:2:4, Type B1, using 20mm graded stone aggregate, as in kerbs, with rounded or chamferred edges including all mouldings, set in cement mortar 1:6 all as specified and as directed.

M&L for providing precast cement concrete 1:2:4, type B1, using 20 mm graded stone aggregate as in cover slabs, etc. set in CM 1:6 all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, type B1, using 20mm graded stone aggregate as in foundation, column footings, plinth beams, etc all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate as in Columns, pillars, piers, posts and strutsand the like all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate in beams, cantilevers, lintels, lintel bands all as specified and directed.

Supply only approved integral water proofing compound all as specified and as directed.

M&L for Brickwork with sub-class `B’ bricks straight or curved on plan, to any radius in half brick thick walls built in cement mortar 1:4 all as specified and as directed.

M&L for use of form work to sides of concrete foundations, column footings, plinth beams and similar works for rough finished flat concrete surfaces, vertical or to batter, all as specified and directed.

M&L for use of form work to sides of pillars, posts, struts, columns, etc. for fair finished concrete surfaces, square, rectangular or polygonal all as specified and directed.

M&L for use of form work to sides and soffits of roof beams, tie beams, lintels, and similar works for rough finished flat concrete surfaces all as specified and directed.

M&L for 2nd class hard wood in scantling, clean sawn fixed in unframed work all as specified and directed.

M&L for 2nd class hard wood plain fillets, square, rectangular or triangular in section, wrought, secured with nails or beads; sectional area exc 13 and n.exc 25 sq.cm all as specified and directed.

Fixing only serviceable timber fillets of any description obtained from dismantling, secured with nails or beads; sectional area exc 13 and n.exc 25 Sq.cm all as specified and directed.

M&L for 35 mm thick second class hard wood, Plain framed, panelled shutter with lock rail and panel of 12mm thick plywood BWR 7 ply with commercial veneers on both faces with size of rails and stiles sizes of members of shutters as specified in SSR Part I, Section 8. Clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for 35mm thick 2nd class hard wood glazed/ gauged shutters, open rebated and prepared to receive glass, gauze, etc. (divided into square with plain, chamfered or rounded, mitred and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (b) and fitted to chowkats all as specified and as directed.

M&L for powder coated aluminium frame work as in doors, partitions and windows using standard aluminium extruded sections with thickness of powder coating not less than 50 microns including provision of glazing clips, hinges, handles, etc all as specified and as directed. Notes: (i) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/ fittings. (ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/ supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary rubber gaskets. (iii) Particle board/ glass panels shall be measured and paid separately.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle and steel tower bolt, hold fasts, complete with glazing bars, dovetailed or welded all as specified and as directed.

S&F Steel ventilators with top hung shutters including hinges with steel peg stays, hold fasts, complete all as specified and as directed.

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on single side reinforced with M.S. Square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelaminated PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of prelaminated PVC sheets on both sides to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing all as specified and directed

S&F 2nd class hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles exc 200 cucm nut n exc 50 cucm all as specified and as directed.

S&F MS butt hinges 100mm in size, medium weight, cold rolled all as specified and directed.

S&F aluminium anodised barrel tower bolt 150mm size all as specified and directed.

S&F aluminium anodised handles, 150mm in size, fabricated type, all as specified and directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S &F Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.complete all as specified and as directed.

S&F Floor door stopper of aluminium alloy body and loungue, anodised, with hard drawn steel spring, overall length of cover plate 150mm fixed in floors complete all as specified and as directed.

S&F Door closer, of aluminium (die cast) body, hydraulically regulated, designation No 3, universal type, suitable for door shutters of weight between 61 to 80kg, all as specified and directed. Make : EVERITE/ ALLWYN

S &F Mortice lock, vertical type, size 100 mm, 4 levers complete all as specified and as directed.

S&F brass knobs, 40mm dia fixed with nut and screw and washer all as specified and directed.

S&F stainless steel wire cloth 0.56 mm nominal dia of wire & average width of aperture 1.18mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

M&L for mild steel TMT bars 8mm dia and over cut to length bent to shape required including cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

All as described in item No. 62 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

S&F rolled mild steel posts and struts in fencing and similar work conforming to Fe-290 Gde E-165 including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets for securing wire mesh etc. all as specified and as directed.

Supply only galvanised iron chain link fencing, any mesh, size and type all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type, fixed to any type of standards, rails, straining bolts, etc. including provision of binding wire all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long and 5 to 10mm dia neck all as specified and as directed

S&F mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering and prepared for hanging or sliding with and including either hooks or hinges and hanging, fastening and fixing complete all as specified and as directed. Note: Steel sheeting or other covering, running rails and guides whereer required shall be measured and paid separately.

M&L for 0.8mm thick mild steel, plain black sheet as in covering to door shutters, wall cladding, water tanks, water troughs, ducts, etc. cut to size, edges beaded if directed, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required all as specified and as directed.

S&F rolled mild steel angle sections as in purlins, distance pieces, cleats and similar works conforming to Fe-410-W Gde-E-250 quality-A including dismantling existing userviceable mild steel works of any description and size all as specified and as directed.

M&L for mild steel flats for wind ties for roof including securing bolts and similar works, conforming to Fe-290 Gde E-165 all as specified and as directed.

M&L for mild steel small articles like bands, straps, including bolts, if required; hooks (stay), hook and pintle hinges; large hasps and staples; hand made sliding bolts; clamps; hold fasts; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar articles conforming to Fe-290 Gde-E-165 all as specified and as directed.

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165 all as specified and as directed.

S&F 4mm dia galvansed mild steel wire mesh of size 50mm x 50mm, fixed to steel members with tinned tacks or galvanised wire staples all as specified and as directed.

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for pre-painted galvalume coated high tensile plain profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roof covering/ claddings to wall, etc. fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

S&F 0.8mm thick galvanised plain mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 all as specified and as directed.

S&F PVC (SWR) eaves gutter half round/ square/ trapezoidal profile 150mm bore including pipe accessories PVC holder bats bolts nuts etc. including taking down existing unserviceable gutters of any description and size and making good disurbed surfaces all as specified and directed.

M&L for 3mm thick Aluminium Composite Panel comprising of a core containing not less than 70% non combustible mineral filling sandwiched between two skins of 0.5mm thick aluminium alloy PERALUMAN-100 (AlMg1-NS41) complete with all necessary sub-structures, anchors, hardware and fittings to provide a total installation, fixed to existing wooden/ steel members all as per manufacturers instructions, all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc. Make: Alstrong/ Aludecor/ Alucobond/ Eurobond

M&L for providing roof treatment with APP modified water proofing membrane with the following specifications all as specified and directed.

Removing existing roof/ chajjas treatment of any type like plastic felt/ HP tiles of any description including taking down existing plastering/ concrete of any thickness and cleaning the top surface of RCC slab with wire brush including removal of debris to a distance exc 50m but n exc 100m

Brushing with neat cement slurry @ 3Kg/Sqm and rendering 10 mm thick in CM 1:3 mixed with water proofing compound and finishing surfaces even and smooth without using extra cement. Note: Water proofing compound shall be measured and paid separately

Preparation of plastered surfaces by removing dust, dirt & applying oil bound bituminous primer at 0.4 litre per Sqm & providing 4mm thick APP modified water proofing membrane weight not less than 4.5kg/ sqm reinforced with non oven polyester mat weight not less than 160gms per Sqm including minimum 10cm side/ over laps & including applying a coat of blown hot bitumen grade 85/25 over membrane at 1.2kg per Sqm & on drying applying a coat of solar reflective bituminous aluminium paint at 0.1kg/sqm.

NOTE: APP modified water proofing membrane shall be of any one of the approved makes as specified here-in-after and shall conform to specifications given IS 16540-2017/ IS 16532-2017. Contractor shall produce necessary test certificate of the manufacturer to the Engineer-in-charge before incorporation in the work. Necessary independent tests shall also be carried out by the contractor without any extra cost to the Deptt as per relevant IS specifications and membranes with satisfactory test results shall only be incorporated in the work.

S&F solid wall lining consisit of 5mm thick wood grain printed PVC sheet inclusive of solvent cement fixed on and including provision of 5mm thick PVC fillet of size 35mm wide fixed at 300mm c/c including necessary PVC strips as required etc complete all as specified and as directed.

S&F 4mm thick High Pressure Steam Cured (HPSC) non asbestos fibre cement building board in false ceiling with aluminum anodized snap grids of 60x60cm with Tee section 35x25x1.25mm, angle section 25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger fittings etc and applying three coats of white wash on ceiling all as specified and directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base for flooring including finishing the surface even and fair all as specified and directed.

M&L for 50mm thick plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base for flooring including finishing the surface even and fair all as specified and directed.

M&L for 100mm thick plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in paving/ hard standing/ floor laid in alternate bays and finishing the concrete surface even and smooth without using extra cement and making impressions of expanded metal while the concrete is green all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded aggregate as in sub base for flooring all as specified and directed.

M&L for coloured non skid ceramic tiles, edge cut, 6 to 7mm thick area of each tile exc 0.06 Sqm but not exc 0.11 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:6 all as specified and directed.

M&L for coloured non skid ceramic tiles, edge cut, 7 to 8mm thick area of each tile exc 0.11 Sqm but not exc 0.18 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:6 all as specified and directed.

M&L for coloured matt fiished ceramic tiles, edge cut, 9 to 10mm thick area of each tile exc 0.18 Sqm but not exc 0.38 Sqm, in floors/ skirting, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured glazed ceramic tiles 200mm x 300m or 250mm x 350mm size, 7mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for machine cut granite stone slab, premium quality, any colour, 18 to 19mm thick, set and jointed with neat cement slurry laid over and including 15mm thick screed bed in cement mortar 1:6 and pointed in white cement (1:2) mixed with colouring pigments to match with the shade of slab, as in partitions, platforms, steps, cills, etc. including rubbing and polishing complete all as specified and directed.

M&L for coloured polished designer cement concrete tiles 30cm x 30cm x 25mm thick, with grey cement and pigments, set jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bed in cement mortar 1:6 as in pathways, etc. complete all as specified and directed.

M&L for chequred cement concrete tiles 30cm x 30cm x 25mm thick, machine pressed, set, jointed and pointed in neat cement slurry, as in pathways, pavings, etc., laid over and including 15mm thick screed bed in cement mortar 1:6 all as specified and directed.

M&L for 80mm thick machine pressed precast concrete interlocking paver blocks with grey cement and pigments, M-40 grade, any shape and size with anti skid finish on top confirming to IS 15658-2006 all as specified and directed.

M&L for 55-60mm thick machine pressed precast concrete interlocking coloured paver blocks, M-35 grade, any shape and size with glossy finish on top confirming to IS 15658-2006 all as specified and directed.

M&L for crushed stone sand (M-sand/ Robo sand/ I-sand) as in cushioning for interlocking paver blocks including watering and consolidating complete all as specified and as directed.

M&L for plain cement concrete 1:3:6, type C1, using 20 mm graded stone aggregate, 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, etc. all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on stone masonry or other than fair faces of brick work finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on stone masonry surfaces or surfaces other than fair faces of brick work or PCC block masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for rendering 15mm thick in cement mortar 1:4 mixed with water proofing compound on fair faces of brick work or block masonry or concrete surfaces of sump well finished even and smooth without using extra cement including scrapping of damaged loosed cement plaster by wire brushes, pressure washing and cleaning the surfaces and disposal of debris n exc 50m complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately

Repairs to existing cracks in concrete surfaces by cutting 40mm wide x 25mm deep grooves along the crack including cleaning groves thoroughly with blower and applying nitobond SBR of FOSROC or equivalent product of other approved manufacturer with suitable brush to form a film on the surface of the grin cracks as per manufacturers instructions and rendering the prepared surfaces in cement mortar 1:3 all as specified and directed. Note: (i) NITOBOND SBR or equivalent product of other approved manufacturer shall be measured and paid seperately. (ii) The work catered under this item shall be carried out through authorised applicator of the manufacturer only.

Supply only Nitobond SBR or equivalent product of other approved manufacturer all as specified.

M&L for pressure grouting of the admixture (Cement and Cebex 100 or equivalent product of other approved manufacturer) through 8mm dia nozzles and drilled and fixed at 1 m distance equally distributed on all affected area of RCC structure including necessary scaffolding for 24m high from ground level all as specified and directed. Notes: (i) Cement and chemicals shall be measured and paid seperately. (ii) The work catered under this item shall be carried out through authorised applicator of the manufacturer only.

Supply only cebex 100 or equivalent product of other approved manufacturer all as specified.

Supply only ordinary portland cement 43 grade all as specified.

M&L for 2 coats of water proof two component acrylic polymer modified elastomeric cementitious waterproof coating on concrete/ wall surfaces using BRUSHBND of FOSROC or equivalent product of other approved manufacturer complete all as per manufacturer's instructions and all as directed. Note: The work catered under this item shall be carried out through authorised applicator of the manufacturer only.

M & L for 4mm thick sheet glass ordinary quality and glazing to aluminium joineries in square n. exc 0.5 sqm in each pane all as specified and directed.

M & L for 5mm thick sheet glass ordinary quality and glazingto aluminium joineries in square exc 0.5 sqm in each pane all as specified and directed.

M&L for three coats of white wash on newly plastered walls, pilasters, cornices, etc. including necessary preparation of surfaces all as specified and directed.

M&L for two coats of oil bound distemper over a coat of primer over 1mm thick layer of wall care putty, on walls, pillasters, cornices, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper any colour, over a coat of primer over 1mm thick layer of wall care putty, on newly plastered walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for preparation of old plastered surfaces of walls by brooming down and applying one coat of cement base paint all as specified and directed.

M&L for two coats of cement based paint, any colour, over a coat of alkali resistant primer on newly plastered surfaces of walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on surfaces of overead reservoirs of 10 to 24m staging with necessary scaffldong/supports, including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for preparing surface of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil all as specified and directed.

M&L for preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for preparation of old steel surfaces of any discription over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for preparation of new steel surfaces not exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for 500 litres capacity rotational moulded polyethylene (HDPE) water storage tanks, 'ISI' marked, cylindrical, vertical with closed top conforming to IS 12701-1989 having two layers wall construction with manhole lid and suitable locking arrangement including making holes for inlet, outlet and over flow pipes, hoisted and fixed in position including testing complete all as specified and directed.

S&F 25mm bore gun metal gate valve heavy duty ISI marked with iron wheel head screwed both ends to iron pipes and fixed all as specified and as directed

S&F 25mm dia PTMT ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe all as specified and directed.

M&L for 15 mm bore UPVC water supply pipes, 10kgf/ sqcm, including all fittings such as elbow, reducer, tee, couplers, short pieces, connectors etc. fixed to walls, ceilings with PVC batten holders all as specified and as directed.

All as described in item No. 125 but 20mm bore UPVC pipes

All as described in item No. 125 but 25mm bore UPVC pipes

S&F 15 mm bore Bib tap, long body, brass chromium plated, fancy type with wall flange, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F 15mm bore stop valves, brass chromium plated, fancy type, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions all as specified and as directed.

S&F pillar taps, brass chromium plated with capstan heads, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed.

S&F vitreous china wash basin, white, size 550x400mm, including CI brackets and cutting for and pinning in ends of brackets or erecting stands etc. all as specified and directed.

S&F Vitreous China urinal, bowl type (back or corner wall type), white, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including provision of grating and union for discharge pipe, 15mm bore brass CP urinal spreader, LDPE waste pipe, (excluding flushing cistern, flush pipe) all as specified and as directed.

S&F vitreous china squatting pan, Orissa pattern, size 580mm x 440mm, white, with integral foot rest (excluding flushing cistern) including 'P' or 'S' trap including provision of lime concrete bedding etc complete all as specified and directed.

S&F syphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe etc complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts, 450mm long all as specified and directed.

S&F brass chromium plated shower rose swivel type 125mm size suitable for fixing with 15mm bore pipe all as specified and directed.

S&F brass chromium plated tubular towel rail 600mm long with and including Chromium plated brass screws & wooden/ plastic cleats all as specified and as directed.

S&F UPVC PVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) pipes, single socketed, in any length, with solvent cement joints, fixed to wall or laid trenches or in floors, all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) pipes, single socketed, in any length, with solvent cement joints, fixed to wall or laid trenches or in floors, all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) bends any radius all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) bends any radius all as specified and directed.

M&L for 150mm bore Salt glazed stoneware drain pipes, laid in trenches and jointed as specified all as specified and directed.

M&L for bed concrete to 150mm bore drain pipes in Plain Cement Concrete 1:4:8 type D2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested all as specified and directed.

Cutting into existing manholes for connecting new drain pipes, 150mm bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required all s specified and as directed.

Taking down carefully point wiring of any description complete for light, fan, 5 A socket, 15 Amps socket, 2 way points and bell point etc including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, holders, etc. all as specified and directed.

M&L for concealed Point wiring complete with 1.5 Sq mm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC conduits of suitable size and all necessary conduit fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly includingprovision of 1.6mm thick MS pressed steel terminal box flush mounted into wall with 3mm thick plastic laminated sheet cover for mounting switches/ sockets etc. for one light point controlled by one switch 1 way complete all as specified and directed.

All as described in item No. 148 but for one fan/ exhaust fan point controlled by one switch and regulator.

All as described in item No. 148 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 148 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

M&L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC casing capping/ PVC conduits of suitable size and all necessary fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including PVC surface mounting box with modular cover plate & frames for mounting switches/ sockets etc. for one light point controlled by one modular switch 1 way complete all as specified and directed.

All as described in item No. 152 but for one fan/ exhaust fan point controlled by one switch and regulator.

All as described in item No. 152 but for one bell point controlled by one bell push

All as described in item No. 152 but for one 05 Amps socket outlet on independent board.

All as described in item No. 152 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 152 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 6 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 6 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Two runs of 6 sqmm cable, one run of 6 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

S&F switch, piano type, 5 Amps, flush button, 230 volts, AC, one way all as specified and directed.

S&F switch, piano type, 15 Amps, flush button, 230 volts, AC, all as specified and directed.

S&F socket outlet 5 Amps 2 cum 3 pin flush type multipurpose all as specified and directed.

S&F socket outlet 15 Amps, 3 pin 5 Amps cum 3 pin 15 Amps, flush type multipurpose all as specified and directed.

S&F modular switch, 1 module, 1 way, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular switch, 1 module, 1 way, 16 Amps 230 volts, AC, all as specified and directed.

S&F modular bell push, 1 module, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular socket outlet, 2 module, 6 Amps 2 cum 3 pin multipurpose all as specified and directed.

S&F modular socket outlet, 2 module, 2 pin 6A/ 3 pin 16 Amps, multipurpose all as specified and directed.

S&F fan regulator electronic modular step type, 2 module, suitable for 1200/1400mm sweep ceiling fan all as specified and directed.

S&F call bell, ding dong 230 volts AC supply all as specified and directed.

S&F ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F surface mounting LED light fitting, 1x 20W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 20W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F surface mounting LED light fitting, 1x 10W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 10W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F in repairs 42 Watts LED glare free luminaire recess mounted in square profile 2ft x 2ft size with 42 W high brightness SMD LEDs for glare free homogenous illumination, including electronic driver etc. complete with all accessories internally pre wired including cutting of false ceiling sheet to required size and fixing aluminium strip as per the existing size in false ceiling for fixing of light fitting and providing aluminium strip supports as reqd and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block all as specified and directed. Make: HAVELLS VENUS NEO HE 2x2 or equivalent in CG/ Philips/ Wipro

S&F 25 Watts LED security light fitting, with pressure die cast aluminium housing and lens embedded PC cover having top opening separate driver compartment with IP66 protection, 6000K and impact resistance IK07, 25 Watts high power LEDs, electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of bracket made out of GI pipe light grade of suitable size and length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA PEARL model of HAVELLS or equivalent in Crompton Greaves/ Philips/ Wipro

S&F in repairs, MCB DB TPN 4 Way with bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F in repairs, MCB DB SPN 12 Way with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCB DB SPN 8 Way with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCB TPN 63A , 'C' series 415 Volts AC supply all as specified and as directed.

S&F MCB DP 63A 'C' series 10KA 50Hz 240 Volts AC supply all as specified and as directed.

S&F MCB DP 40A 'C' series 10KA 50Hz 240 Volts AC supply all as specified and as directed.

S&F MCB SP 5-32A 10KA 'C' series 50Hz 240 Volts AC supply all as specified and as directed.

S&F ceiling fan, 230 volts, single phase, 1200mm sweep, 3 blades, Star rating with all accessories complete including taking down existing unserviceable ceiling fan of any description and size from the location and setting aside for fixing/depositing to MES E/M store all as specified and as directed. Make: HAVELLS Model No. ES-50 or equivalent model in Crompton Greaves/ USHA

M&L for 50mm dia GI pipe medium grade cut to required length as per site requirement and fixed into walls in single piece without any joints as in supports for hanging of ceiling fans complete all as specified and directed.

S&F exhaust fan, 300mm sweep, 230/240 Volts, 900 RPM, heavy duty, single phase, metallic body with louvres and fixing arrangements with fixing bolts and provision of 3 core flexible copper conductor cable of size 1.5sqmm size from ceiling rose to connector of exhaust fan and testing including making circular hole of suitable in brick masonry wall and making good disturbed surfaces to match with existing surfaces all as specified as directed. Make: Havells Venti Air DSP model or equivalent model in Philips/ Crompton Greaves

S&F storage type water heater (Geyser), vertical type, 50 litres capacity, 2000/1500 Watts, Star rating including drilling holes into wall, provision of 4 Nos of suitable size anchor bolts, nuts and washers, connecting up electrical & water supply lines, testing complete all as specified and as directed. Make: MONZA EC model of HAVELLS or equivalent model in RACOLD/ BAJAJ

M&L for XLPE insulated, armoured, heavy duty electric LT UG cable with multi-stranded aluminium conductor, 1100 Volts grade, cross sectional area 25 Sqmm x 4 core, laid in trenches/ passing through pipe/ duct or fixed to wall including provision of necessary lugs/ thimbles/ ferrules, connecting up , testing and commissioning complete laid in repairs all as specified and as directed. Note: Excavation, earth work, cable cushioning, bricks/ GI pipe for protection shall be measured and paid separately under relevant items of this schedule.

M&L for double wall corrugated HDPE pipes, conforming to IS 14930-2001, ISI marked, 63mm outer dia, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches/ under roads/ crossing etc. all as specified and as directed.

M&L for GI tubes, light grade, 40mm bore, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches / under roads/ crossing etc. all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

ASHOK M RAJGOLKAR

M/s. KIRAN M CHOUGULE

M/s. N D KALING

A. N. Kalbhavi

M/S MAHADEV M PATIL