ADDITION ALTERATION OF JCOs ORs MD ACCN AT ARTY CENTRE HYDERABAD

Amount

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out as in hard/dense soil complete all as specified and directed.

Hard core of broken stone aggregate guage n exc 63mm deposited spread and levelled in layers n exc 15 cm thick watered and well rammed to true surfaces

Demolition of cement concrete (reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level)

Demolition of concrete unreinforced of any description and in any position not otherwise specifcally provided for.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish out side MD land all as directed.

Taking down completely existing treatment along with plaster as in sunken slabs vertical faces complete all as specified and directed by Engr-in-Charge.

Cement concrete in floors, type B-1, 1:2:4 (20mm graded stone aggregate), 40mm thick finishing even and smooth using extra cement with IWPC (IWPC measured and paid separately) as in sunken slab.

Cement concrete in floors, type B-1, 1:2:4 (20mm graded aggregate), 40mm thick finishing even and fair.

Applying evenly a coat of blown type bitumen at the rate of 1.5kg/Sqm and blinding with clean dry sand at 0.05Cum/Sqm.

Rendering on brick or concrete surfaces with 15mm thick in CM 1:3, finished fair and even with IWPC (IWPC measured and paid separately) as in sunken slab.

Cement concrete 1:5:10 type E2, using 40mm graded stone aggregate in foundations, fillings and mass concrete complete all as specified and directed

Low density polyethylene pipes (LDPE) of pressure rating 6 Kgf/sqcm fixed to walls, floors etc of 32mm bore as in spouts for sunken slabs

Machine cut cudappah stone slab 20-25mm thick over 20 mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

Cement concrete 1:3:6 type C1, using 20mm graded stone aggregate for in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones bed plates, kerbs, water troughs and like including weathering, slightly rounded or chamfered angles and throating, as directed.

Cement concrete 1:4:8 type D2, using 40mm graded stone aggregate, 75mm thick, as in flooring, finishing surfaces even and fair complete all as specified and directed.

Cement concrete type C2 1:3:6, using 40mm graded stone aggregaate finished even and smooth without using extra cement, 75mm thick as in plinth protection and paths complete all as specified and directed.

Cement concrete 1:2:4, type B0 (using 12.50mm graded stone aggregate) 20mm thick finished even and rough for receiving floor finishes

Screed bed or bedding layer of mortar 15mm thick in CM 1:6 for laying of floor tiles etc. all as specified.

Non skid coloured ceramic tile 7 to 8 mm thick (Squre/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade

Non skid coloured ceramic tile 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade

Rendering in CM 1:4, 10mm thick on brick/concrete surfaces finished fair and even as in backing coat.

Glazed ceramic coloured tiles in vertical surfaces 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match

Demolition of brick or stone/boulder masonry built in cement mortar including all quions, arches pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles.

Half brick work with sub class B bricks straight or curved on plan to any radius with old size bricks built in CM 1:4 all as directed and as specified.

Brick work with sub 'B' class brick straight or curved on plane exceeding 6 M mean radius built in cement mortar 1:6

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

Rendering, 10 mm thick on fair face of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement.

Rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth with out using extra cement all as specified.

Rendering in cement mortar 1:3, 5mm thick on fair faces of ceiling surfaces and finished even and smooth without using extra cement.

Two coats of oil bound distemper over a alkali resistant primer on newly plastered surfaces including 3mm thick wall care putty on wall including preperation

Preparing newly plastered surfaces of walls and applying two coats of cement based paint over a coat of Alkali resistant primer

Preparation of newly plastered surfaces of ceiling and applying three coats of white wash all as specified and as directed.

Complete removal of existing treatment and applying two oil bound distemper over a coat of alkali resistant primer on old surface of walls including 3mm thick wall care putty on wall complete

Complete removal of existing treatment and applying two coats of cement base paint over a coat of alkali resistant primer on walls surfaces .

Complete removal of existing treatment and applying three coats of white wash on ceiling all as specified and as directed.

Taking down shutters of any description exc. 1sqm but not exc. 2 sqm each including builders hardware as directed.

Taking down chowkats or frames with shutters (with out taking off shutter from the frame) of any description alongwith fittings exc 1.5sqm but n.exc 4 sqm each all as specified and as directed

Second class hardwood plain fillets square or rectangular or triangular in section clean sawn, secured with nails or brads of cross section exc 3 Sq cm but not exc 6 Sq cm in repair.

Second class Hard wood, plain, solid straight chowkats and frames rebated on the solid, rounded or chamfered put together with glue pinned at joints, supplied and fitted all as specified and as directed.

Factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides thickness of shutter 35mm complete all as speified and directed by Engr-in-Charge.

Second class hardwood, Glazed and skeleton shutters, 35mm thick, open rebated and prepared to receive glass, gauze, etc divided into squares, with plain,chamfered or rounded, mitred and rebated sash bars any numbers fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I,Section 8 clause 8.4(a) to fitted chowkats

Second class hardwood factory made panelled shutters 35mm thick, plain framed (any no of panels) with panels of timber flat on both sides (feather edged) or 12mm veneered particle board commercial veneering on both faces, the size of rail and stile as per IS :1003 (Part I), kiln seasoned and chemically pressure treated.

Supplied and fitted to chowkats, 30mm thick, 2nd class hardwood shutter, Plain, framed, panelled shutters (any number of panels ) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density wood particle board with commercial face veneers;

applying two coats of Synthetic enamel paint for wooden surfaces over a coat of pink primer including necessary preparation of new wooden surfaces of any description exc. 10cm width or girth.

preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint of Ordinary tint as directed.

Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt of length 300mm and not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate

Mild steel barrel tower bolts, stove enamelled black, with bright bolt 100mm in length

Mild steel barrel tower bolts, stove enamelled black, with bright bolt 150mm in length

Mild steel barrel tower bolts, stove enamelled black, with bright bolt 150mm in length in repairs.

Mild steel pressed handles, oval type, stove enamelled black, 125mm long

Mild steel pressed handles, oval type, stove enamelled black, 150mm long

Mild steel pressed handles, oval type, stove enamelled black, 150mm long in repair.

Butt hinges, 75mm size medium weight cold rolled mild steel.

Butt hinges, 100mm size medium weight cold rolled mild steel.

Mild steel wire, type I, Gate and shutter, hooks and eyes 125mm size

300mm mild steel , ordinary rat tail rod pattern springs including roller and roller plate complete.

150mm over all length of cover plate, floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor.

Taking down chowkats or frames with shutters (without taking off shutter from the frame) of any description alongwith fittings n.exc 1.5sqm each all as specified and as directed

Taking down shutters of any description not exc 1 sq. m each and re-fixing in same opening.

Resecuring or easing and adjusting without taking down Shutters of any description exc 1 sq. m and n. exc 2 sq. m each.

Solid PVC door frame of size 50mmx47mm made out of 5mm thick plain colour PVC sheet reinforced with 19mm MS square tube of 19 gauge mitred cut at two corners and joined by inserting two Nos of 150mm long brackets of 15mm x 15mm MS square tube inside

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type C-21 size of hinges 100 mm.

Extruded aluminium alloy handles, fabricated type, anodised, size of handle 150mm.

Aluminium anodised barrel tower bolts of extruded section 150mm long.

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with out glazing bars, dovetailed or welded

Steel ventilator with top hung shutter including hinges, steel peg stay, complete

Preparation of new steel surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified.

Two coats of synthetic enamel paint on old steel surfaces including preperation width or girth exc 10cm

Sheet glass 3mm thick plain ordinary quality and glazing with oil putty/wooden beads as directed in squares n.exc 0.50 sqm each pane.

Figured glass, pin head type, 4mm thick and glazing with oil putty in squares n exc 0.5 sq. m in each pane

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture, 1.40mm and fixed with stainless steel wire staples.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture, 1.40mm and fixed with stainless steel wire staples/ wooden beading or with necessary arrangement in repairs.

Supply, hoisting and fixing in position of 500 litres capacity two layered Rotational Moulded Polyethylene water storage tank (cylindrical vertical with closed top) all as specified in SSR Part- I including dismantling the existing PVC OHT .

Hoisting and fixing in position of 1000 litres capacity two layered Rotational Moulded Polyethylene water storage tank (cylindrical vertical with closed top) all as specified in SSR Part- I including dismantling the existing PVC OHT .

Ball valve 20 mm dia high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 grams).

Galvanised steel water tubing, 15mm dia medium grade including provision of all pipe fittings such as bends, tees, elbows, reducers, unions, plugs, sockets etc., fixed to walls/ceilings or laid in floors etc., complete including taking up or down and removal to store.

Galvanised steel water tubing, 20mm dia medium grade including provision of all pipe fittings such as bends, tees, elbows, reducers, unions, plugs, sockets etc., fixed to walls/ceilings or laid in floors etc., complete including taking up or down and removal to store.

Stop valve/ cock Chromium Plated fancy type and screwed both ends for iron pipe 15mm dia bore or for union all as specified and as directed in repairs.

Bib taps Chromium Plated fancy type and screwed down, screwed for iron pipe 15mm bore or for brass ferrule all as specified in repairs.

Vitreous china Squatting pan Orissa pattern of size 580mx440mm white with integral foot rests (excluding flushing cistern and flush pipe) complete including concrete bedding in repairs.

PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe.

Vitreous china wash basin, white, flat back size 550x 400mm including 15mm fancy type Chromium Plated pillar tap, waste, chain and plug and porcelain stopper, brackets, cutting for and pinning in ends of brackets or erecting stand and 32 mm waste pipe in repair.

PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified.

PVC (SWR) floor trap for 75mmdia outlet plain with grating including jointing with solvent cement in repairs.

PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in floor 75mm dia complete in repairs all as directed.

PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in floor 110mm dia complete in repairs all as directed.

PVC (SWR) branch piece double (double Y) equal or unequal with access door of bore 75mm

PVC (SWR) junction double (double T) equal or unequal with access door of bore 75mm

PVC (SWR) branch piece double (double Y) equal or unequal with access door of bore 110mm

PVC (SWR) bend any radius with access door suitable for 110mm dia pipes.

PVC (SWR) bend any radius suitable for 110mm dia pipes in repairs.

PVC (SWR) bend any radius suitable for 75mm dia pipes in repairs.

PVC (SWR) bend any radius with access door suitable for 75mm dia pipes in repairs.

PVC (SWR) junction double (double T) equal or unequal with access door of bore 110mm in repairs.

PVC (SWR) junction single (single T) equal or unequal with access door of bore 75mm

PVC (SWR) Vent cowl suitable for 110mm dia vent pipe.

Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm in repairs.

Stainless steel plate rack , in repairs, made out of stainless steel 1 mm thick sheet of size 38" x 36" all as specified.

125mm size brass chromium plated shower rose with or without swivel joints including fixing to steel pipe or union fixed in repairs.

PTMT towel rail 600mm long fixed with and including Chromium plated brass screws and wooden/plastic cleats

Soap dish, vitreous china white, approx size 125mm, oval type, fixed to plugs with chromium plated brass screws in repairs.

Designer curtain rods (Drapery rods) of 25.4 mm dia aluminium exterior grade 3mm thick with holding clambs and fixed to wall with PVC rawl plug and brass screws, all as specified and as directed includiding dismantling old one of any description.

Aluminium designer curtain rod brackets suitable for curtain rods

18/19mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with nails to timber frame work in repairs.

Gun metal 20 mm bore dia of pipe globe or gate valve with iron wheel head screwed both ends for iron pipe in repairs.

Supply only Integral water proofing compound .

Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) in repairs

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc., laid bedded and pointed in any mortar

Machine cut kota stone slab flooring 20-25mm thick over 20 mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and rounding the edges complete all as specified and directed.

Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement mortar and incl backing coat 10mm thick CM (1:3) as in skirting.

Preparing old surfaces of walls by brooming down or by steel wire brushing and applying one coat of white wash.

Hacking out old broken glass (any thickness, size quality or description) from wooden, steel or stone, concrete or brick sorrounds, glazed with putty or fixed with beads

Continuous (piano) hinges of width of flaps 40mm (when open) , mild steel, bright finish or electrogalvanised.

Pre Cast Cement Concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in Cover slab for manholes etc set in cement mortor 1:4 including use and waste necessary form work (Reinforced shall be measured and paid seprately) all as specefied

TMT bars 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip

Chequered cement concrete tiles 30cm x 30cm x 25mm thick with grey cement and pigment, machine pressed, set jointed and pointed in neat cement slurry in floors including 15 mm thick screed bedding layer in CM 1:6.

Mild steel Angles, bars, flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps and similar small articles confirming to Fe-290 Gde-E-165

Taking down existing felt, plaster and preparing the surface of roof by cleaning of foreign materials down with water complete all as specified and directed.

Cement concrete type B0 1:2:4 (12.5mm graded stone aggregate) as in padding and benching & filletting with IWPC (IWPC measured and paid seperately)

Roughening surfaces of old concrete floor or concrete surfaces by picking, sweeping clean and washing down with water to remove dust, etc.and brushing neat cement slurry with 3 Kg of cement per square metre complete all as specified and directed.

Cement plaster in CM 1:3, 10mm thick mixed with water proof compound as per manfucaturer instruction, finished fair & even on brick or concrete surfaces. (WPC shall be measured and paid seperately).

APP based polymeric membrane minimum weight 3kg/sqm and minimum 3mm thick, reinforced with polyster non-woven fabric (weight not less than 150 gms/sqm) laid over primed roof surfaces with bituminous primer confirming to IS-3384 applied at 0.3 Ltr/Sqm by forced application and applying one coat finished with one coat of aluminium paint at 100 ml/sqm, 100mm overlap fused uniformly by LPG torch flame, complete all as specified and diected.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, fixed with self tapping screws as specified

Dismantling wrought iron or mild steel work any description not other wise provided for.

Steel door including projecting type hinges with steel handle, and glazing bars, dovetailed or welded complete all as specified.

Galvanised, corrugated mild steel 0.63 mm thick sheeting with two corrugations side lap,fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275.

MS framed structure roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats of Grade Fe 410 -W (Gde- E- 250) quality- A

Supplied and fixed to wooden or steel framework with expanded metal weight per square metre not exc 4.0 Kg, cut to length, bent to shape required and tying with and incl annealed mild steel wire not less that 0.9 mm dia or fixing with galvanised steel staples complete.

Taking down and removing rubbish off broken glass coping on top of walls.

Broken glass coping on top of walls in CM 1:3 all as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc., ) or insulation boards/ slabs/ blankets, any thickness, including cover fillets.

Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre., etc complete, as specified and directed in repairs.

Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, etc complete, as specified and directed in repairs.

12mm thick Gypsum Board ceiling fixed with screw as per manufacturers instructions etc completed all as specified.

Taking out carefully copper/ aluminium point wiring, Light, fan, socket or power complete with all fitting, fixtures such as switch socket out let, ceiling rose, holder, regulator, switches, bells, DBs etc including making good the disturbed surface of wall/ floors complete

Point wiring for one light point/fan point/bell point controlled by one switch with 1.5 sqmm multistrand copper conductor cable PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 1.50 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable ( green colour) as earth lead in and including non metalic rigid PVC conduit medium grade with appropriate size with all fittings (ISI Marked) suitable for concealed wiring on stone/brick,masonary walls,roof etc including in new /old CI/MS sunk box of required size and all as directed by Engineer-in-Charge & 3 mm thick plastic laminated sheet for housing switches sockets, regulators etc, including making good the disturbed surfaces to match with the existing specification ,complete all as specified and directed at site .

All as per ser item No 143 here in before but for one 3 pin socket outlet 5 Amp independent.

All as per ser item No 143 here in before but for one 3 pin socket outlet 5 Amp on same board.

All as per ser item No 143 here in before but for one 3 pin socket outlet 15 Amp independent board using cable of size 2.5 sqmm with 2.5 sqmm PVC (FRLSH) insulated unsheathed copper conductor single core cable (green colour) as earth lead.

All as per ser item No 143 here in before but for one light point controlled by two, two way switches.

Switch piano flush type 5 amps single pole one way

Switch piano flush type 5 amps single pole Two way

Switch socket outlet combination universal type, 2 in 1, 2 and 3 pin 5 Amp, piano flush type, 240 volts, complete all as specified and as directed at site.

Switch socket outlet combination universal type, 2 in 1, 3 pin 5 and 15 Amp, piano flush type, 240 volts, complete all as specified and as directed at site .

Ceiling rose, poly carbonate, isolated body with 2 to 3 terminals.

Lamp holder insulated body with back plate suitable for battern fittings complete all as specified and directed at site.

LED Bulb 7 watt complete for lamp holder all as specified.

Electronic fan regulator stepped type with five step 240 volts suitable for 1200/1400 mm sweep AC ceiling fan complete, all as directed as site.

Bell push A/C 5 Amps, 230 Volts flush type.

Bell ding-dong 230 V, single pole all as specified.

LED batten luminaire surface mounted 4 feet system wattage of 20 Watts and not less than 2000lm with lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD< 10%, colour temperature≥5700K, surge protection3KV in CM, IP-20 protected, meets LED IS specifications, , Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50DegreeC, system efficacy at luminarie level ≥ 100 Lumens/watt and including connecting up with PVC sheathed 1.5 sq mm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed. Make-Philips of Catalogue No. BN021CLED20SPSU CW GR S2, HAVELLS Cat pt No ENDURALINEAR NEOBS20WLED865SPCWH, or equivalent in wipro

Environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head Back-lit LED luminaire comprising of high brightness LEDs, 10W, IP 66 protection including connecting up with PVC sheathed 1.5 sq mm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed. Make- HAVELLS Cat pt No HEXAFT10WLED857SSYMBOPC or equivalent in WIPRO, BAJAJ

Geyser for New generation energy saving & enviromental friendly long life versitile pressure die cast capacity 25 ltrs BEE 4 Star rated.

Sheet metal enclosure IP-43 double door for DBs(where MCBs are reqd) SPN 240 V, for 08 ways, complete all as specified.

MCB, SP, 6-32 amps, 'C' curve, AC, 230volts, 50Hz, 10KA all specified and directed by Engr-in-Charge

MCB,SPN, 6-32 amps, 'C' curve, AC, 230volts, 50Hz, 10KA all specified and directed by Engr-in-Charge

Sheet metal enclosures, double door, for MCB DB load link, Vertical, triple pole and neutral, 4 way IP-43, Suitable for MCCB up to 160A as incommer.complete all as specified.

Thermal magnetic release MCCB 4 pole 415 volt rapturing capacity 16 KA 0f size 100 amp complete all as specified.

Exhaust fan 300mm sweep copper wound,1400 rpm, AC, 230 Volts, 50 Hz complete , all as specified and directed. MAKE : BAJAJ/USHA

Sub main wiring with two single core PVC-FRLS insulated unsheathed multi stranded Submain wiring with two single core PVC (FRLS) insulated flexible copper conductor cable of size 6.0 Sqmm and one single core PVC (FRLS) insulated unsheathed flexible copper conductor cable green colour of size 6.0 Sqmm as earth lead in and including PVC conduit medium grade with all fittings laying on surface conduit and making good the disturbed wall surfaces to match with existing specification all as required at site incl taking down old unserviceable sub main wiring complete all as specified at directed. Note : (i) Two single core cable and one run of earth copper cable will be measured and paid as one unit length

Earthing complete with galvanized steel earth plate electrode 60cmX60cmX6.0 mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) normal with top edge of plate not less than 1.5m below normal ground level, earth plate connected to galvanized earth lead wire 4.00mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 of MES SSR part I connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 meter long for earth wire including PCC (1:2:4) pit with precast RCC (1:2:4) type B -1 cover, 40mm thick with lifting hooks made out of 6mm dia MS bars, watering arrangement with funnel, wire, common salt, charcoal filling, necessary excavation and earth work in any type of soil complete all as specified.

Tamper proof with inbuilt intelligence Electronic Energy meter single phase, two wire direct connected meter (whole current) instantaneous Parameter (voltage P-n, PF, frequency current line KW Demand, LDC Display , Optical port class 1.0s (240 volts 10-30 Amps) complete including poly carbonate box with connection of suitable size wire including meter box single phase with locking arrangements molded in UV stablised transpherant polycarbonate/ flame retardent high grade engineering plastic with unique arrangements for plifer proof interlocking with hinge type box.complying to IS14772 With salableoptical port provision,etc as directed. Seal and sealing wire and furnishing details of Qtr. No. Meter No. initial reading, writing with paint of MES No. all a sspecified& directed at site. NOTE : OLD u/s meters are to be deposited at E/M store Yard.

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc., not exc 10sqm on plan and n.exc 1.5m in depth and getting out in Hard/dense soil.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in excavated material/soil.

Removing excavated material / soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point

Steel water tubes, medium grade, 25mm dia bore, ISI marked as per IS-1239 Part-I, galvanised, with all fittings such as bends, tees, elbows, reducers, unions, plugs sockets etc laid in trenches complete all as specified and as directed including taking down.

Steel water tubes, medium grade, 20mm dia bore, ISI marked as per IS-1239 Part-I, galvanised, with all fittings such as bends, tees, elbows, reducers, unions, plugs sockets etc laid in trenches complete all as specified and as directed including taking down.

Steel water tubes, medium grade, 50mm dia bore, ISI marked as per IS-1239 Part-I, galvanised, with all fittings such as bends, tees, elbows, reducers, unions, plugs sockets etc laid in trenches complete all as specified and as directed including taking down.

Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25mm dia bore complete all as specified and directed including taking down old unserviceable valve.

Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 50mm dia bore complete all as specified and directed including taking down old unserviceable valve.

Cutting/Boring on the existing CI/GI pipe line 80/100mm dia (in position) for insertion of new galvanised Tee 80 x 50 mm for branch connection incl necessary jointing material comlete all as specified and as directed.

Construction of Brick masonry valve chamber (230mm thick wall) of 500 x 500 x 500mm internal size, PCC 1:4:8 type D2 using 40mm graded stone aggregate for foundation, brick wall with sub class `B’ bricks built in CM 1:6, PCC 1:2:4 type B1 using 20mm graded stone aggregate for coping rendering in CM 1:4 15mm thick including provision of MS sheet cover 2mm thick fixed to MS angle frame made out of 40x40x4mm thick with 2 coats of synthetic enamel paint over one coat of red oxide primer to steel surfaces and locking arrangements with godrej lock including necessary excavation and earth work in any type of soil.

Construction of Brick masonry valve chamber (230mm thick wall) of 600 x 600 x 600mm internal size, PCC 1:4:8 type D2 using 40mm graded stone aggregate for foundation, brick wall with sub class `B’ bricks built in CM 1:6, PCC 1:2:4 type B1 using 20mm graded stone aggregate for coping rendering in CM 1:4 15mm thick including provision of MS sheet cover 2mm thick fixed to MS angle frame made out of 40x40x4mm thick with 2 coats of synthetic enamel paint over one coat of red oxide primer to steel surfaces and locking arrangements with godrej lock including necessary excavation and earth work in any type of soil.

Construction of Brick masonry valve chamber (230mm thick wall) of 900 x 900 x 900mm internal size, PCC 1:4:8 type D2 using 40mm graded stone aggregate for foundation, brick wall with sub class `B’ bricks built in CM 1:6, PCC 1:2:4 type B1 using 20mm graded stone aggregate for coping rendering in CM 1:4 15mm thick including provision of MS sheet cover 2mm thick fixed to MS angle frame made out of 40x40x4mm thick with 2 coats of synthetic enamel paint over one coat of red oxide primer to steel surfaces and locking arrangements with godrej lock including necessary excavation and earth work in any type of soil .

Taking out carefully old u/s LT cable of any size including connecting materials complete all as directed by Engineer-in-Charge.

Supply & Laying in trenches/drawn through pipes or in road crossings / paths/ drains / ducts / floors / along poles / equipments etc., of LT cable under ground, heavy duty, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade 2 core x 10 sq mm cross sectional area including connecting up using suitable size aluminium lugs testing and commissioning complete all as specified and directed.

Supply & Laying in trenches/drawn through pipes or in road crossings / paths/ drains / ducts / floors / along poles / equipments etc., of LT cable under ground, heavy duty, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade 2 core x 16 sq mm cross sectional area including connecting up using suitable size aluminium lugs testing and commissioning complete all as specified and directed.

Supply & Laying in trenches/drawn through pipes or in road crossings / paths/ drains / ducts / floors / along poles / equipments etc., of LT cable under ground, heavy duty, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade 3.5 core x 35 sq mm cross sectional area including connecting up using suitable size aluminium lugs testing and commissioning complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal of unserviceble materials out of site for 40/80mm bore all as specified and directed

Steel tubes light grade, 40mm dia bore, ISI Marked as per IS-1239 part-I galvanised with all fittings and fixed complete to wall and ceilings, on pole or laid in floor or in trenches etc. for protection of under ground cables complete all as specified.

Well burnt bricks sub class 'B' in trenches for cable protection of Under Ground cable all as specified.

Spreading of crushed stone dust/M-sand in trenches for underground cable including punning down of sand in layer complete all as specified and directed. Note :- Thickness of sand cushion after punning down i.e 18 Cm shall be measured for payment

Sri Lakshmi Enterprises

Mavee Syndicate

Sri Associates