PROVISION OF CERTAIN MINOR MAJOR REVENUE WORKS AND SPECIAL REPAIR TO CERTAIN OTM ACCN AT AFS KANHERI HILLS UNDER GE AF THANE

Amount

Demolition of reinforced Concrete of any description and in any position not otherwise specifically provided for chajja, fins, louvers, parapet, floor, Roofs, floors (other than ground floors), beams, staircases,landing, and similar suspended work (reinforcement cut as required to facilitate demolition) etc from any by hammering carefully of concrete with necessary scafolding and protection as required all as specified and directed by Engr-in-Charge.

Taking down/dismantling loose/damage concrete including plaster of any description and in any position from RCC structures like chajja, fins, louvers, parapet, column, beam, and of lintel by hammering with wooden mallets carefully chipping off the old concrete surface including cutting of rusted reinforcement if so required and disposal of old debris to outside the premises complete all as specified and as directed.

Cleaning the existing surface of concrete and reinforcements as obtained after execution of item No. 1,2 here in before by wire brush including scrapping & cleaning with emery paper and washing down with water as required and applying “Solvent free epoxy concrete bonding agent” as per manufacturer’s instructions on old concrete surfaces for bonding with new concrete complete all as specified & as directed.

Applying two coats of “Epoxy zinc rich primer” as protective coat to expose surface of old and new reinforcement over 10 mm dia as per manufacturer's instructions complete all as specified & as directed.

All as per item No.4 above but reinforcement upto 10mm dia. Note for item No 3 to 5 : (i) Cost of chemical i.e. Solvant free epoxy, Epoxy zinc rich primer and cement and TMT bar shall be measured and paid separately under appropriate item here in below. (ii) The work shall be carried out by the trained person as per manufacturer's instructions i.e. FOSROC/SIKA/ PIDILITE

Supply only. epoxy zinc rich primer. Make : Nitozinc primer of FOSROC/Friazinc R of SIKA/ or equivalent in PEDILITE

Supply only. Solvant free Epoxy concrete bonding agent. Make : Nitobond EP of FOSROC/Carbodur of SIKA/ or equivalent in PEDILITE. Note for item No 6 & 7 : Eqvivalent product of PIDILITE shall only be considered if specific brand of FOSROC/SIKA as mentioned above is not available in the market subject to production of sufficient documents to judge non availability and equivalency by the Accepting officer.

Supply only cement.(OPC 53 Grade Confirming to IS:12269-1987)

Material and labour for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending lapping etc as required and welding with existing bar complete all as specified & as directed. (Welding shall be measured and paid separately).

Material & labour for mild steel TMT bars 6 to 8mm bar, cut to length, bent to shape required, including cranking, bending, lapping etc as required and welding with existing bar complete all as specified & as directed. (Welding shall be measured and paid separately).

Material and labour for mild steel TMT deformed bar or twisted bars upto 10mm dia as in stirrups cut to lenth bent to shape required including cranking ,bending etc and lapping ,welding as directed to the existing one complete all as specified & as directed. (Welding shall be measured and paid separately).

Material and labour for 4mm thick tack welding @ 150mm centre to centre for connection/jointing new with old reinforcement in any position complete all as specified and as directed.

Material & labour for providing reinforced cement concrete (1:1½: 3) type A0 (using 12.5mm graded stone aggregate) mixed with integral water proofing liquid admixture CONPLAST X421IC (Fosroc) or equivalent as per manufactures instructions as in columns, pillars,lintel, slab supported walls roof, landings, balconises, canopies, deck slabs and in shelves etc complete all as specified & as directed.

All as per item No. 13 above but in Chajja, facia, railing and parapet etc (Note for item No 13 & 14 : Integral water proofing compound shall be measured and paid separately).

Use and waste of formwork to sides of pillars, posts,struts, piers, columns and stanchions for rough finished concrete surfaces complete all as specified and as directed.

Use and waste of formwork to sides & sofits of chajja, facia, railing, parapet etc for rough finished concrete surfaces complete all as specified and as directed.

Demolition of brick masonary built in cement mortar including all quions, arches, pillars etc but including ashlars facings, dressed stone work and pre cast concrete articles all as specified and directed by Engr-in-Charge.

M&L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and set in CM 1:6 of type C1, 1:3:6 using 20mm graded aggregate complete all as specified and directed.

Taking down cement plaster of any description on brick walls including raking out joints, hacking for key, scrubbing down with water complete all as specified & as directed.

Material and labour for 20mm thick plaster in cement mortar (1:4) in two layers, i.e 10mm thick in each layer, top layer mixed with integral water proofing liquid admixture as per manufacturers instruction on brick or concrete surfaces of wall finished fair and even complete all as specified & as directed. Note :- WPC shall be measured and paid separately.

Supply only integral water proofing liquid admixture for concrete and mortar (Make :CONPLAST X421IC of Fosroc /SIKA No 1 of SIKA/equivalent brand of PIDILITE)

Material & labour for rendering 15mm thick in cement mortar (1:6) on fair faces of brickwork or concrete surfaces, finished even and smooth (without using extra lime or cement) complete all as specified and directed.

Material and labour for rendering 05mm thick in CM (1:3) on concrete surfaces as in column, lintel,beam,chajja,facia, railing etc. Inclduing finished even and smooth without using extra cement complete all as specified and as directed.

All as per item No.23 but in ceiling.

M&L for preparing new plastered surfaces, and applying two coats of oil bound distemper on walls over a coat of alkali resistant primer, complete all as specified and directed by Engr In Charge.

Material and labour for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified & as directed.

All as per item No.26 above but in ceiling.

M&L for preparing new plastered surfaces of wall and applying two coats of acrylic weather paint exterior grade over a coat of weather coat primer complete all as specified and directed by Engr In Charge.

M&L for preparing decorated surfaces, and applying one coats of oil bound distemper on walls complete all as specified and directed by Engr In Charge.

M&L for preparation of existing treatment on wall and applying one coat of acrylic paint complete all as specified and directed by Engr In Charge.

Taking out old unserviceable floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified & directed

Material and labour for non-skid coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exceeding 0.06 Sqm but not exce 0.11 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed or bedding layer in CM(1:6) complete all as specified and as directed.

Material and labour for glazed ceramic colour tiles 300x200 x7mm thick in skirting/dados etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour tiles complete all as specified and as directed.

Material and labour for 20mm thick screed bed in CM 1:4 for laying floor finishes complete all as specified and directed by Engr-In-Charge

Material and labour for Vitrified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-In-Charge

Material and labour for rendering 10mm thck in CM 1:4 as backing coat to receive tiles in vertical position as dado/skirting complete all as specified and directed by Engr-In-Charge

Material and labour for Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in vertical position as dado/skirting. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-In-Charge

Supply and fix in repairs sheet glass ordinary quality 3.00mm thick and glazing with oil putty in squares exc 0.5 sqm in each pane

Removing existing water proofing treatment where so ever exist (except concrete padding) and removing debris/rubbish off the site and MD land as directed

Demolition of cement concrete of any description and in any position provided as in roof padding, roof curb etc complete all as specified and as directed. Note: - (a) Demolition should be done carefully to roof slab. (b) Any damage occurred in the roof surfaces during demolition shall be made good by the contractor without extra cost to the department. (c) Disposal of debris/retrieved materials shall be thrown out of site at place as directed by the Engineer-in-Charge.

Material and labour for providing plain cement concrete type B- 1, (1:2:4) using 20mm graded stone aggregate as in roof padding laid in slope as per requirement mixed with integral water proofing liquid admixture as per manufacturer's instructions complete all as specified and as directed. Note : (i) Minimum thickness of PCC shall be 50mm. (ii) Integral water proofing liquid admixture shall be measured and paid separately under appropriate item here in after

M & L for APP modified roof treatment over existing RCC roof complete all as specified and directed by Engr-in-charge and as specifird here under:- (a) Apply bitumen primer at 0.4 lit /Sqm with density of 0.87 to 0.89 kg/liters at 25 degree C on prepared dry roof surface.(b) Laying 3 mm thick APP membrane wt not less than 3.0 kg/sqm by torch application with minimum side lap 10cm and end lap 15 cm.The laying of membrane shall be done through an authirised applicator of manafractures of APP menbrane.(c) Over the membrane provide a solor reflective bituminius aliminium paint @ 0.1kg/sqm prescribed by manafacture complete all as specified.

Labour only for disconnecting existing over head tanks of capacity exc.500 and n.exc 1000 ltr, setting aside or lowering if required for repair of roof water proofing treatment and hoisting, reconnecting and re-fixing in position after necessary work without damaging to existing services etc. all as specified and directed.

Surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out

Excavation intrenches n.exc 1.5m wide and n.exc 1.5m deep for foundation n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out of Hard/dence soil

M & L for PCC (1:4:8) type D2 (using 40 mm graded aggregate) as in foundation, filling in and mass concrete complete all as specified and as directed.

M&L for TMT bar 10mm dia and over cut to length bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with MS wire not less than 0.9 mm dia or securing with clips.

Ditto as item no-47 above but TMT bars 6 to 8mm bar, cut to length, bent to shape required, including cranking, bending, lapping etc as required and welding with existing bar complete all as specified & as directed. (Welding shall be measured and paid separately).

M&L Formwork to soffit of suspended slabs such as roof slabs , floor slabs, landing and similar work; not exceeding 200mm thick.

M&L for form work on the side RCC beams, cantilevers, bressummers, lintels over 1.5m span.

M&L form work to foundation/footing, footing of colums rough finish surfaces all as directed

M&L for RCC M-30 design mix as in RCC slabs supporetd on walls, beams and columns in floors, roofs,landings, balconies, canopies, deck slabs and in shelves and the like.

M&L for RCC M-30 design mix as in RCC beams, cantilevers, bressummers, lintels over 1.5m span.

M &L RCC M-30 using 20mm stone Agg design mix for in footings , raft footing etc complete all as specified and directed.

M &L RCC M-30 using 20mm stone Agg design mix for in columns etc complete all as specified and directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 mixed with water proofing compound including finished even and smooth without using extra cement complete all as specified and directed by Engr in Charge. Note: Water proofing compound will be measured and paid seperately complete all as specified and directed.

Supply only integral water proofing compound.

M&L for rendering 15mm thick in CM 1:6 finished even & smooth with sagol finish to internal surfaces.

M&L for PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing will be painted to match with printed sheed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

M&L 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square in n exc 0.5 sq.m in each pane complete all as specified and directed.

Returning filling including spreading levelling watering and well ramming n.exc 25cm thick complete all as specified and directed.

Supply and fix 50mm GI pipe, medium grade in isolated length of 400mm long inserting into wall surfaces with 100mm projecting from the external face of wall as in water draining spout complete all as specified and directed.

Material and labour for rendering in CM (1:4),15mm thick on wall of sunken floor suraces finish the surface even and smooth without using extra cement mixed with water proofing compound complete all as specified and as directed . (Note : WPC will be measured and paid in supply only rate)

Materials & labour for water proofing treatment to sunkun floors with the following courses of treatment :- (a) Apply first layer of slurry of cement @ 0.488 kg/sqm mixed with acrylic polymer modified cementitous composite compounds @ 0.126 kg/sqm all as specified. (b) Apply second layer of slurry of cement @ 0.242 kg/sqm mixed with acrylic polymer modified cementitous composite compounds @ 0.253 kg/sqm including cleaning the surfaces and all as specified. (c) Apply 200 micron thick polythene film pasted with the help of adhesives shall be provided over treatment all as specified. Note :- The slope of slab shall be 1:20 towards the corner of outer walls and GI pipe of 50mm dia (medium grade) be inserted at corner projecting out side 10 cm which should be measured and paid separately,

Material and labour for cement concrete 1:4:8 type D2 (using 40mm stone aggregate) as in filling in sunkun floor complete all as specified & directed.

Ditto as above Glazed ceramic tiles Coloured and size of tiles 350x250x7/450x350x7mm thick in wall/dado etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match all as specified.

M&L for 15mm bore medium grade GI tubing with all fittings fixed to walls and ceiling or laid in floors ,complete all as specified and directed.

M&L for 20mm bore medium grade GI tubing with all fittings fixed to walls and ceiling or laid in floors ,complete all as specified and directed.

S&F Bib taps, cast copper ally with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed fancy type ,complete all as specified and directed.

S&F stop cock valve 15mm bore cast copper alloy screwed down high pressure with cruch or butter fly handle screwed both ends for iron pipe all as specified and directed.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed fancy type ,complete all as specified and directed.

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed ,complete all as specified and directed.

S&F PVC connector 15mm bore 600mm long with brass connector ,complete all as specified and directed.

S&F low level flushing system plastic valveless syphonic action type white with inlet ball valve float chain and ball (of capacity 10 ltrs ISI marked inck 32mm PVC flush pipe Make Commander or equivalent ISI marked ,complete all as specified and directed.

S&F CP Towel rail 20 mm dia, D type 60 cm long ,complete all as specified and directed.

S&F wash basins, vitreous china (flat back or angle type or oval type counter fixed) any size incl cutting for and pinning in ends of brackets or recting stand including brackets and waste pie etc.,complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:3 with smooth finish as in ceiling ,complete all as specified and directed.

M&L orrisa pattern viterious china ware white glazed WC 630x450mm with integral foot rest fixed ,complete all as specified and directed.

M&L viterious china bowl urinal flat back, size of 465 x 355 x 265 mm white ( minimum ) with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) ,complete all as specified and directed.

S&F 500 Ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I ,complete all as specified and directed.

S&F 20mm Ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed ,complete all as specified and directed.

S&F 110 mm bore PVC (SWR)soil, vent and waste pipes,Single socketed, in any length with rubber ring joint, laid in trenches or in floors as directed and specified.

S&F 110 mm bore PVC (SWR)soil, vent and waste pipes,Single socketed, in any length with rubber ring joint, fixed to walls as specified and directed.

S&F 110mm bore PVC (SWR) junction single , (single T) equal or unequal.

S&F 75 mm bore PVC (SWR)soil, vent and waste pipes,Single socketed, in any length with rubber ring joint, laid in trenches or in floors as directed and specified.

S&F 110mm bore PVC (SWR) junction single , (single Y) equal or unequal ,complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius ,complete all as specified and directed.

S&F 110mm bore PVC (SWR) cowl ,complete all as specified and directed.

S&F 110mm PVC (SWR) traps 'P' ,complete all as specified and directed.

M&L 75mm PVC (SWR) multi Floor trap, plain with grating including jointing with solvent cement ,complete all as specified and directed.

M&L 110mm PVC (SWR) gully trap, including jointing with solvent cement ,complete all as specified and directed.

Removing excavated soil exc 50m and n.exc 250 m and deposited at a level n.exc 1.5m above the starting point ,complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

M&L PCC 1:2:4 type B2 using 40 mm graded aggregate as in foundation complete all as specified and directed.

S&F for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63mm,Broken stone or boulders deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed.

M&L Sand filling under floors including watering & consolidation complete all as specified and directed.

M&L for machine pressed precast coloured concrete interlocking paver block with lacquer finish any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade with grey cement & pigment complete all as specified and directed.

M&L for providing cement concrete in mud stops rounded or chamfered on edges ( as at edge/end of interlocking paver block) complete all as specified and directed.

M&L for Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed.

Material and labour for filling HDPE sand bags Khaki colour of Size 30 cm X 30 cm X 80 cm with sand, closing the open end with nylon wire and placing/stacking where directed, complete all as specified and directed by Engr-in-Charge. (Sand bag Cat No- B/N/IV manufactured by DCPL or Equivalent.) Note : Sand for the filling measured under seperate item that supply only sand.

Supply only Fine aggregate (sand) for filling in to the sand bags as refered in above item No-105

M&L for Block board 18 to 19mm thick , interior grade commertial type fixed with screws to timber frame work complete all as specified and directed by Engr-in-Charge

M&L for Plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads, Exc 13 Sq cm & n Exc 25 Sq cm. complete all as specified and directed by Engr-in-Charge

M&L for Plain fillets, square, rectangular or triangular in section, clean sawn, secured with mills or brads, not Exc 3 Sq cm. complete all as specified and directed by Engr-in-Charge

M&L for 0.9 mm thick decorative laminate type 1 of surface finished colour and pattern as approved, fixed with approved adhehive as per manufacturer's instruction complete all as specified and directed by Engr-in-Charge

Labour only for making chamfers, splays, grooves, rebates, rounded angles, rounded nosings, tongued and grooved edges (each tongue and each groove measured) etc., exc 3mm but n. exc 75m girth softwood complete all as specified and directed by Engr-in-Charge

M&L for finishing coat with synthetic varnish on new surfaces by sizing, wood filler liquid transperant staining with oil on surfaces of any description over 10 cm in width or girth. complete all as specified and directed by Engr-in-Charge

M&L for finishing coat with synthetic varnish on new surfaces by sizing over fillet coat of thin varnishon surfacse of any description, not exc 10cm in width or girth when unconnected with other work or painted in different tint complete all as specified and directed by Engr-in-Charge

S&F Stainless steel soft close hydraulic action hinge with capacity to take load of 12 to 20 mm thick board all as per directed and specified by Engr-in-charge

S&F for 75 mm brass handles, cast type , polished type complete all as specified and directed by Engr-in-Charge

S&F 4 levers locks, for cupboard/cabinets, grade I, size 50mm complete all as specified and directed by Engr-in-Charge

Cutting holes into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required exc 250 Sqcm and n.exc 500 Sqcm superficial area complete all as specified and directed by Engr-in-Charge

M&L for framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engr-in-Charge

M&L preparation of new or previously untreated surface & applying two coat synthetic enamel Painting over a coat of preiming red red oxide zinc chrome complete all as specified and directed by Engr-in-Charge.

Taknig down Chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sq. m but n exc 4 sq m each ,complete all as specified and directed by Engr-in-Charge.

M&L for toughened glass as in doors/ partitions 12 mm thick fixed with stainless steel/brass fixtures and fastenings with floor mounted heavy duty hydraulic door closer etc complete all as specified and directed.

S&F mat finish handle of 450mm long all as specified and directed by Engr-in charge.

M&L Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S & F CP coated brass lock vertical type with four levers all as specified

M&L black granite (of any type) 20mm thick work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment

S&F rolled sections with ERW or induction butt welded MS tubes black conforming to I S 1161-1979 grade St 240. as in main and cross beam, hip and jack rafters, prlins when connected to common rafers, and running rails & guides for sliding door, fixed with angle cleats or other connecting plates as directed by engr-in-charge conforming to IS 1161-1979 grade St 240 complete all as specified and directed.

S&F Plates (plain or chequered) channels. Fe 410-W (Gde E-250) quality B , Square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed.

S&F Mild steel bolts,exc 12 mm n exc 20 mm, purpose made, with hexagonal or square head one end and screwed the other, or screw both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long complete all as specified and directed.

M&L for 75 mm thick cement concrete type B-2, 1:2:4 using 40 mm graded aggregate as in flooring finished even and smooth without using extra cement complete all as specified and directed.

Taking down Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets, Light Fitting, etc. and Making Good Disturbed Surfaces of Walls, Floors, etc. so as to match with the Existing Finishes, complete all as specified and as directed.

Taking down the existing unservicable Sub-main Wiring of any type and any description as existing at Site including Making Good the Disturbed Surfaces of Walls, Floors, etc. so as to match with the Existing Finishes, complete all as specified and as directed.

Taking down the existing unserviceable Main Switch/ Cut out/ DBs of any type/ capacity and any description as existing at Site including Making Good the Disturbed Surfaces of Walls, Floors, etc. so as to match with the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable drawn through and including Rigid Non- metallic PVC Conduit 25mm in size, medium grade, ISI marked and its Accessories in Concealed (Partly)/ Surface (Partly) with necessary grouting of required size and depth on Wall and making Good in Cement Mortar 1:3 mounted on 1.6mm thick Sunk Mild Steel Pressed Terminal Box of suitable size duly painted with Red Oxide Metal Primer with 3.0 mm thick Plastic Laminated Sheet Top Cover for mounting Switches, Sockets, Fan Regulators, etc. including 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable (Green Colour) as Earth Continuity Conductor connected to Common Earth dolly for ONE LIGHT/FAN POINT CONTROLLED BY ONE 1-WAY SWITCH 6 AMP, complete all as specified and as directed. Make: Philips/Legrand/Havells/wipro/Anchor

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable drawn through and including Rigid Non-metallic PVC Conduit 25mm in size, medium grade, ISI marked and its Accessories in Concealed (Partly)/ Surface (Partly) with necessary grouting of required size and depth on Wall and making Good in Cement Mortar 1:3 mounted on 1.6mm thick Sunk Mild Steel Pressed Terminal Box of suitable size duly painted with Red Oxide Metal Primer with 3.0 mm thick Plastic Laminated Sheet Top Cover for mounting Switches, Sockets, Fan Regulators, etc. including 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable (Green Colour) as Earth Continuity Conductor connected to Common Earth dolly for ONE 3 PIN SOCKET OUTLET 6 AMP ON INDEPENDENT BOARD, complete all as specified and as directed. Make: Philips/Legrand/Havells/wipro/Anchor

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable drawn through and including Rigid Non-metallic PVC Conduit 25mm in size, medium grade, ISI marked and its Accessories in Concealed (Partly)/ Surface (Partly) with necessary grouting of required size and depth on Wall and making Good in Cement Mortar 1:3 mounted on 1.6mm thick Sunk Mild Steel Pressed Terminal Box of suitable size duly painted with Red Oxide Metal Primer with 3.0 mm thick Plastic Laminated Sheet Top Cover for mounting Switches, Sockets, Fan Regulators, etc. including 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable (Green Colour) as Earth Continuity Conductor connected to Common Earth dolly for ONE 3 PIN SOCKET OUTLET 6 AMP ON THE SAME BOARD, complete all as specified and as directed. Make: Philips/Legrand/Havells/wipro/Anchor

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable drawn through and including Rigid Non- metallic PVC Conduit 25mm in size, medium grade, ISI marked and its Accessories in Concealed (Partly)/ Surface (Partly) with necessary grouting of required size and depth on Wall and making Good in Cement Mortar 1:3 mounted on 1.6mm thick Sunk Mild Steel Pressed Terminal Box of suitable size duly painted with Red Oxide Metal Primer with 3.0mm thick Plastic Laminated Sheet Top Cover for mounting Switches, Sockets, Fan Regulators, etc. including 2.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable (Green Colour) as Earth Continuity Conductor connected to Common Earth dolly for ONE 3 PIN SOCKET 16 AMP ON INDEPENDENT BOARD, complete all as specified and as directed. Make: Philips/Legrand/Havells/wipro/Anchor

M&L Point Wiring with 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable drawn through and including Rigid Non- metallic PVC Conduit 25mm in size, medium grade, ISI marked and its Accessories in Concealed (Partly)/ Surface (Partly) with necessary grouting of required size and depth on Wall and making Good in Cement Mortar 1:3 mounted on 1.6mm thick Sunk Mild Steel Pressed Terminal Box of suitable size duly painted with Red Oxide Metal Primer with 3.0 mm thick Plastic Laminated Sheet Top Cover for mounting Switches, Sockets, Fan Regulators, etc. including 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable (Green Colour) as Earth Continuity Conductor connected to Common Earth dolly for ONE 3 PIN SOCKET 16 AMP ON INDEPENDENT BOARD, complete all as specified and as directed.Make: Philips/Legrand/Havells/wipro/Anchor

M&L Sub-main Wiring with 2-Runs of 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable drawn through and including Non-metalic Rigid PVC Conduit of size 25mm dia, medium grade, ISI marked and its Accessories including 1-Run of 2.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable (Green Colour) as Earth Continuty Conductor along with the Wiring in Concealed and Making Good Disturbed Surfaces of Walls/Roofs/Floors, etc. so as to match with the Existing Finishes, complete all as specified and as directed. Make:Anchor/Havells/ L&T/RPG or Asian

M&L Sub-main Wiring with 2-Runs of 6.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable drawn through and including Non-metalic Rigid PVC Conduit of size 25mm dia, medium grade, ISI marked and its Accessories including 1-Run of 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable (Green Colour) as Earth Continuty Conductor along with the Wiring in Concealed and Making Good Disturbed Surfaces of Walls/Roofs/Floors, etc. so as to match with the Existing Finishes, complete all as specified and as directed.Make:Anchor/Havells/ L&T/RPG or Asian

S&F PVC Flexible Pipe, ISI marked, heavy duty of size 25mm with all Fittings including taking down old unserviceable one, complete all as per specified and as directed.

S & F Rigid non metallic PVC conduit 25 dia (external ) ISI marked (on surface) incl of all accessories and all fittings such as Tees,bends, elbows, reducers, bell mouth, tube ends and fixing accossories such as couplers,lock nuts, saddles, pipe hook etc complete all as specified and directed

S&F Switch Piano 6 Amp, Flush type, Single Pole, 1-way, complete all as specified and as directed. Make: Philips/Havells/Anchor

S&F Switch Piano 16 Amp, Flush type, Single Pole, 1-way, complete all as specified and as directed. Make: Philips/Havells/Anchor

S&F Socket Outlet 6 Amp, Piano, Flush type, 2-in-1, multi-purpose, 3 Pin, complete all as specified and as directed. Make: Philips/Havells/Anchor

S&F Socket Outlet 6 Amp & 16 Amp, Piano, Flush type, 2-in-1, multi-purpose, 5 Pin, complete all as specified and as directed. Make: Philips/Havells/Anchor

S&F Lamp Holder, Insulated body PVC/Polycarbonate with Back Plate suitable for Batten Fitting, complete all as specified and as directed. Make: Philips/Havells/Anchor

S&F Ceiling Rose, 3 Terminals, PVC Polycarbonate, Isolated body complete all as specified and as directed. Make: Philips/Havells/Anchor

S&F Fan Regulator in 5 Step type, Single Pole, 230 Volt, Electronic type, complete all as specified and as directed. Make: Philips/Havells/Anchor

S&F Decorative Ultra Slim Linear LED Lighting Fixture with Extruded Polycarbonate, Environmental Friendly, Energy Efficient 5 Watt LED 6000K and connecting up with and including Copper Conductor Cable of size 23/0.0076 multi-stranded, 3 Core from Ceiling Rose to Light Fitting, complete all as specified and as directed. Make: Havells /Wipro/Philips/Crompton Greaves.

S&F Decorative Ultra Slim Linear LED Lighting Fixture with Extruded Polycarbonate, Environmental Friendly, Energy Efficient 10 Watt LED 6000K and connecting up with and including Copper Conductor Cable of size 23/0.0076 multi-stranded, 3 Core from Ceiling Rose to Light Fitting, complete all as specified and as directed.Make: Havells /Wipro/Philips/Crompton Greaves.

S&F Decorative Wall light fitting made up of Polycarbonate with 0.5 W LED lamp (B-22 base) LED 6000K and connecting up with and including Copper Conductor Cable of size 23/0.0076 multi-stranded, 3 Core from Ceiling Rose to Light Fitting, complete all as specified and as directed. complete all as specified and as directed. Make: Havells /Wipro/Philips/Crompton Greaves.

S&F Decorative Ultra Slim Linear LED Lighting Fixture with Extruded Polycarbonate, Environmental Friendly, Energy Efficient 18 Watt LED 6000K and connecting up with and including Copper Conductor Cable of size 23/0.0076 multi-stranded, 3 Core from Ceiling Rose to Light Fitting, complete all as specified and as directed.Make: Havells /Wipro/Philips/Crompton Greaves.

Taking Down and Refixing Decorative Ultra Slim Linear LED Lighting Fixture with Extruded Polycarbonate, Environmental Friendly, Energy Efficient 18 Watt LED 6000K and connecting up with and including Copper Conductor Cable of size 23/0.0076 multi-stranded, 3 Core from Ceiling Rose to Light Fitting, complete all as specified and as directed. Make: Havells /Wipro/Philips/Crompton Greaves.

S&F MCB Single Pole, 6 to 32 Amp, 240 Volt, AC, 'B' Series for fixing on MCB DB’s, 10 kA, 50 Hz and connecting up, complete all as specified and as directed. Make: Schneider/C&S/CG/Legrands/Havells/L&T

S&F MCB Single Pole & Neutral, 40 Amp, 240 Volt, AC, 'C' Series for fixing on MCB DB’s, 10 kA, 50 Hz and connecting up, complete all as specified and as directed. Make: Schneider/C&S/CG/Legrands/Havells/L&T

S&F Sheet Metal Enclosure, Single Pole & Neutral with a 2-Pin and Earth Plug and Socket with 1 No. MCB Single Pole, 20 Amp, 240 Volt and connecting up, complete all as specified and as directed. Make: Schneider/C&S/CG/Legrands/Havells/L&T.

S&F MCB DB 8-way, Single Pole & Neutral, Double Door type, Regal Grey Colour, Sheet Steel Phosphatised, Powder Coated with 200 Amp rate Bus-bar, Neutral Link Earth Bar & Din Rail duly embedded in Wall including Concealed upto Wall Surface including connecting with existing Cable Incoming and Outgoing with Cable Lugs as per the requirement and and Making Good Disturbed Surfaces of Walls/Roofs/ Floors, etc. so as to match with the existing Finishes, complete all as specified and as directed.Make: Schneider/C&S/CG/Legrands/Havells/L&T.

S&F MCB DB 4-way, Single Pole & Neutral, Double Door type, Regal Grey Colour, Sheet Steel Phosphatised, Powder Coated with 200 Amp rate Bus-bar, Neutral Link Earth Bar & Din Rail duly embedded in Wall including Concealed upto Wall Surface including connecting with existing Cable Incoming and Outgoing with Cable Lugs as per the requirement and and Making Good Disturbed Surfaces of Walls/Roofs/ Floors, etc. so as to match with the existing Finishes, complete all as specified and as directed. Make: Schneider/C&S/CG/Legrands/Havells/L&T.

S&F Load Line DB 4-way Enclosure Double Door with Incomer MCCB 100 Amp rating, 25 KA, 3 Pole and suitable for 415 Volt 50 Hz AC Supply including taking down old unserviceable one, complete all as per specified and as directed. Make: Schneider/C&S/CG/Legrands/Havells/L&T.

Supply and fix Ceiling fan 220V, 50 Hz of 1200 mm sweep energy efficient ISI Marked 5 Star Rated with regulator and three core twisted cable of suitable size for connecting upto ceiling rose and accessories given by manufacturer complete all as specified and directed. Make: Bajaj/Havells/Crompton/Orient.

Supply and fix exhaust fan, energy efficient heavy duty 300 mm sweep, 1400 RPM enrgy efficient, with louvers, Single phase, 50 Hz with three core twisted cable of suitable size for connecting upto ceiling rose complete all as specified and directed. Make: Bajaj/Havells/Crompton/Orient.

M&L Earthing with Galvanised Steel Earth Plate Electrode 600x600x 6mm, buried directly in ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50 mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, Funnel with GI Watering Pipe 20mm bore (dia) medium grade including necessary Excavation in Soft/Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion including taking down old unserviceable one, complete all as per specified and as directed.

Nissan Electricals