REPAIR TO ROADS, FOOT PATH, KERB STONE AND ROAD FURNITURE AT SEKHON VIHAR AREA AT AF STN PALAM UNDER GE (AF) GURGAON NO.1

Amount

M&L for Preparing existing black top surfaces by brushing with wire brushes for removing caked mud ect sweeping with brooms and finally cleaned surfaces with Air compresser to remove all loose dust for black top surface complete all as specified and directed.

M&L for applying paving bitumen evenly a priming/tack coat with bituminous primer at 05 kg per 10 Sqm of VG-10 grade for Black Top surface complete all as specified and directed..

M&L for bituminous premix asphaltic semi dense concrete, 30 mm (consolidated thickness) with 5.5% paving bitumen binder of VG 30, by weight of total mix, rolled and compacted to required camber and gradient with 8 to 12 tone capacity power roller to a uniform smooth surface as specified and as directed. Note: The actual requirement of binder shall be as per the job mix design and the tests specified. However quantity of bitumen from the mix design found more than specified 5.5% same shall be provided with no extra cost to the Govt. In case binder content found to be less than 5.5% as per mix design as specified in Schedule "A" shall be adjusted @ the rate of 65.00 (Rs sixty Five ) / kg for the less quantity of bitumen used. The quantity of 5.5% mentioned is exclusive of any wastage and no wastage shall be taken into account for the purpose of above adjustment). Note : (i) The work shall be strcitly carried out by using mechanical/sensor paver only . (ii) The design mix shall be carried out from IIT/NIT/Govt Institution and quoted rate shall be inclusive of the same. Work will be allowed only after approval of semi dense asphaltic concrete design mix. (iii) Contractor shall arrange bitumen extraction test at site during execution of SDAC work. The copy of same shall be fwd to this HQ. (iv) The copy of PV shall be submitted by contractor for claiming payment in RAR. Non-submission may lead to non-payment

Preparation of road surfaces and applying thermoplastic reflective paint in marking of minimum 2.00 mm thick single coat as in centre line and edge line road marking of 100 mm width using 'HOT MARK' thermoplastic paint (Hot application) white/yellow by indigenous modern propolled road marking machine as directed including all ingredients such as blinder, glass beads Titanium dioxide calcium carbonate inter fillers themoplastic reuirement for glass shall be the table No 800.4 of MORTH specification including spraying of glass beads etc all as per manufacture instructions complete all as specified and directed.ed.

M&L for Repairs to pot holes any depth, n.exc 1 sqm each including sweeping free from dust and mud or water, scoring sunken surfaces in road, path etc cutting around edges to making good by filling in screened and graded road materials over a priming / tack coat with good by applying tack coat (VG-10) @ 5 kg per 10 sq m, putting in premixed bituminous macadam (VG-30), well rammed and sealed with binder 9.8 kg per 10 sq m, binded with 0.09 cu m of stone chippings, 6.3 mm size and again well rammed (including supply of premixed macadam, binder and chippings). depth of potholes exc 30 mm complete all as specified and directed.

S&F in repair solar road studs of size 125x125x25mm (60mm shank) made frome alumnium alloy and constrution solar powered by nanocrystal solar panel type with rechageable bettary minimum 2.5 V, 500 Mah LED both sides (three each sides) display colour red. Visual distance approx 800 meter in working temperature (10 degree to 70 degree centrigrade) with starting intenstany 300 Lux to 600 Lux. Minimum approx weight 900 grams water resistant made up high compressive material can sustain over 10 tones with one year replacement warranty including epoxy for fixing in position complete all as specified and directed. Note:- (i) Appropriate epoxy adhesive on the road surface shall be provided as per manufacturers specifiaction before fixing the cat eye/stud and the same is includued in quoted rate by the contractor complete all as specified and directed. (ii) Purchase vouchers shall be submitted by the contractor before claiming the payment of RARs/Final bill.

Schedule of Credit

PAWAN KUMAR

Dk Enterprises