SPECIAL REPAIR TO BLDG NO P 3 FOR SINGLE OFFRS ACCN 13 THE MALL AND OTHER SANCTIONED WORKS UNDER GE (WEST) FEROZEPUR CANTT

Amount

Taking down Chowkhats or frames with shutters (without taking of shutters from the frame) not exceeding 1.50 Sqm each of doors /windows complete all as specified and directed.

Taking down Chowkhats or frames with shutters (without taking of shutters from the frame) exceeding 1.50 Sqm but not exceeding 4.00 Sqm each complete all as specified and directed.

S&F 105 mm x 60 mm size pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

S&F 125 mm x 60 mm size pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

M&L cement concrete 1:2:4, type B1 (using 20mm graded stone aggregate) as in hold fast, bed plates, coping, filling of pressed steel chowkhats and all other similar works complete all as specified and directed.

S&F mild steel work in hold fasts, wall ties, pintle hinges and all other similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L cutting holes in brick walls exceeding half bricks but not exceeding full brick built in cement mortar or cement lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 complete all as specified and directed.

Taking down of shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down old Aluminium Doors/ windows / ventilators with frames including all fittings etc of any description complete all as specified and directed.

S&F powder coated Aluminium frame (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings.

S&F powder coated Aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings.

S&F powder coated of (any colour) Aluminium window, ventilator etc fixed / sliding or pull and push type in shutter frames or shutters with two/three track sliding Aluminium frame of approved size, including necessary joining cleats, glazing clips,powder coated Aluminium snap beading, screws, including necessary anodised Aluminium fittings like handles etc complete all as specified as per manufacturers instructions. Note: EPDM Rubber beading/gasket measured and paid for seperatley. Make (Aluminium frame) : Jindal/Hindalco

M&L 5.5 mm thick sheet glass, ordinary quality and glazing with Aluminium beads and rubber gasket in square exceeding 0.5 Sqm in each pane frosted on one side complete all as specified and directed.

S&F EPDM Rubber beading around glass in Aluminium windows /ventilator shutters complete all as specified and directed.

S&F solar control film 25 micron reflective type sticked to glass panes as per manufacturers instruction complete all as specified and directed.

M&L 35mm thick, framed panelled shutters of 2nd class hard wood (any number of panels) with panels of timber flat on both sides feather edged or of veneered particle board medium density wood, with commercial face venners and fitted to chowkats complete all as specified and directed. Note: The size of rails and styles as per IS 1003 (Part I) kiln seasoned and chemically pressure treated.

S&F 2nd class hard wood 30mm thick glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc(without sash bars) edges of framing plain, chamfered or rounded, fittted with cut and mitred beads for securing gauge,etc sizes of member of shutter as specified SSR part-I Section 8 clause 8.24 (a) and fitted to chowkhats complete all as specified and directed.

S&F factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) ( printed with wood grain (colour as approved ) consisting of frame made out of MS tubes for top and bottom rails , MS frame shall be covered with heat moulded wood grain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and colour PVC sheet for top rail, lock rail, and bottom rail on either side and as gap insert for top rail and bottom rail . Panelling of prelam PVC sheet used instead of wood grain PVC sheet. Stiles and rails feathered at edges the MS frame welded / sealed to the stiles and rails with 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900) used instead of exposed portion of PVC sheet beading complete all as specified and directed.

S&F butt hinges 100 mm long, medium weight, cold rolled mild steel, and fixed in repair complete all as specified and directed.

S&F 100mm size butt hinges exturded Aluminium alloy with galvanised mild steel hinge pin anodised and fixed type C-21 complete all as specified and directed.

S&F 200 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed in repairs of complete all as specified and directed.

S&F 125mm extruded Aluminium alloy handle complete all as specified and directed.

S&F extruded Aluminium alloy handles 200 mm long, fabricated type, anodised in repair complete all as specified and directed.

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate in repair complete all as specified and directed.

S&F floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor in repair complete all as specified and directed.

S&F 150 mm floor door stopper of Aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and as directed.

S&F 4 lever Aluminium mortice lock, vertical type size 100 mm complete all as specified and directed.

S&F hydraulically regulated extruded Aluminium body door closer designation No 3 universal type suitable for door shutters of 851mm to 1000mm in width and weight between 61 Kg to 80 Kg etc complete all as speciified and directed.

S&F Aluminium tower bolt of extruded section, 100mm length of bolt and fixed with screws, complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 250mm length,with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-Aluminium alloy and fixed complete all as specified and directed.

S&F 2nd class hardwood plain fillets exceeding 6 and not exceeding 13 sqcm in square, rectangular or triangular section, clean sawn, secured with nails or brads complete all as specified and directed.

S&F 2nd class hardwood plain fillets exceeding 3 and not exceeding 6 sqcm in square, rectangular or triangular section, clean sawn, secured with nails or brads complete all as specified and directed.

M&L medium density fibre board interior grade 18mm-20mm thick solid construction type, fixed in repairs in Kitchen cabinets/ CBs doors shutters/ shelves (horizontal or vertical of any type) on timber frame work with screws /nails complete all as specified and directed.

M&L 0.90 mm thick decorative laminate type -1, both sides of boards surface finish, (colour and pattern as approved) fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F auto close type brass/ stainless steel hinges 150 mm size complete all as specified and directed.

S&F extruded brass handles, 125 mm for CBs of fabricated type polished complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7mm to 8mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per ser item No 39 here-in-before but as in skirtings/ dados fixed on 10 mm thick rendering in cement mortar 1:4.

M&L vitrified ceramic (light shade) coloured tiles 10 mm thick (square / rectangular) polished, area of each tiles not exceeding 0.36 Sqm laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match premium quality as specified and as directed.

All as per ser item No. 41 here-in-before but as in skirtings fixed on 10 mm thick rendering in cement mortar 1:4.

M&L non-skid ceramic tiles coloured 7mm to 8mm thick (square/ rectangular), premium quality on vertical surfaces such as in skirting /dado etc area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed.

M&L glazed ceramic coloured tiles 350mm X 250mm / 450mm X 350mm and 7mm thick on vertical surfaces such as dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

M&L glazed ceramic coloured tiles 300mm X 200mm and 7 mm thick on vertical surfaces such as dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

M&L machine cut Kota stone slab flooring 40mm-50mm thick over and including 15mm thick screed in cement mortar 1:6 laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, steps, plateforms, wall/pillars, apron laid bedded and pointed in any mortar etc complete all as specifed and directed.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L Dholpur stone cladding of 16 mm - 18 mm thick stone gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 Sqm area and not exceeding 0.5 Sqm fixed with and including one number SS clamps (grade -202) of flat 30mm X 2mm, 150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment complete all as specified and fixing as per manufacturer's instruction.

Taking down of unserviceable steel windows with frame (without taking down shutters and grill from frame) of size not exceeding 1.50 Sqm each including cutting holes of appropriate size for insertion blocks of cement concrete hold fasts complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples in repair complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) rom metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

S&F 4 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane in repair complete all as specified and directed.

All as per ser item No. 55 here-in-before but sheet glass is ground or obscured or frosted, on one side.

S&F framed work such as grills, gratings etc, with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors framed balausters, walk ways, railings, frame work of water tanks and similar works conforming to Fe 290, Gde - E-165 complete all as specified and directed.

M&L preparing new surfaces of wood and wood based surfaces of any description, not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of new steel surafces of any description not otherwise described, over 10 cm width or girth, priming with a coat of red oxide primer and applyinng two coats of synthetic enamel paint of approved shade complete all as specified and directeed.

M&L preparation of old painted steel surfaces, of any description, not otherwise described over 10 cm width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

S&F vitreous China wash down water closet pan (White) one piece of size 680mm x 370mm x 750mm with integrated cisteren, seat cover and twin flush settings including soft close seat cover and connection to drain in repair complete all as specified and directed. Make :- Prayag (PICASSO) or techno-commercially equivalent in approved makes.

S&F vitreous China wash basin white (half padestal type) of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets or erecting stand including waste coupling in repair complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F15 mm chromium plated central hole basin mixture with 450 mm braided connection pipe (without pop-up) including all fittings in repair complete all as specified and directed.

S&F 15 mm chromium plated wall mixture (wall mounted) with bend pipe for overhead showers connecting legs and wall flanges including all fittings and complete all as specified and directed.

S&F chromium plated bib cock 15 mm with flange and aerator complete with all fittings in repair complete all as specified and directed.

S&F chromium plated angle cock 15 mm with wall flange complete with all fittings and in repair complete all as specified and directed.

S&F chromium plated concealed stop cock 15 mm with adjustable wall flange complete with all fittings in repair complete all as specified and directed.

S&F chromium plated over head rain shower - ABS type Square 180mmx180mm complete with all fittings in repair complete all as specified and directed.

S&F chromium plated health faucet ABS body (push type) with wall hook and 1.0 m SS Braded rubber hose pipe in repair complete all as specified and directed.

S&F chromium plated toilet paper holder with flap guard in repair complete all as specified and directed.

S&F chromium plated tumbler with holder glossy finish in repair complete all as specified and directed. Make - Prayag (Cantabile-Clea) or techno-commercially equivalent in approved makes.

S&F chromium plated towel rack with hooks 600 mm long with brass finish and glossy type in repair complete all as specified and directed. Make - Prayag (Cantabile-Picasso) or techno-commercially equivalent in approved makes.

S&F chromium plated towel ring in repair complete all as specified and directed.

S&F corner glass shelf 300 mm with ABS brackets 300mmx600mm in repair complete all as specified and directed. Make - Prayag (ABS Bracket) or techno-commercially equivalent in approved makes.

S&F chromium plated soap dish in repair complete all as specified and directed.

S&F PVC cabinet mirror of size 450mm x 600mm in repair complete all as specified and directed. Make- Prayag or techno-commercially equivalent in approved makes.

Taking up or down steel /UPVC water tubing and connections,15 mm bore complete all as specified and directed.

Taking up or down steel /UPVC water tubing and connections, 20 mm bore complete all as specified and directed.

Fixing only, after cleaning old steel tubing, 15 mm dia bore and connections in new or old position using new fittings complete all as specified and directed. Note:- Servicable pipes obtained from item 79 shall be reused and cost of new fittings, if required shall deemed inclusive of quoted rates.

Fixing only, after cleaning old steel tubing, 20 mm dia bore and connections in new or old position using new fittings complete all as specified and directed. Note:- Servicable pipes obtained from item 80 shall be reused and cost of new fittings, if required shall deemed inclusive of quoted rates.

S&F 15 mm water tubes, 'Meduim grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F 20 mm water tubes, 'Meduim grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L cutting, chasing pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sun shades shelves, lintels etc and cutting chase for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10 cm girth in brick wall complete all as specified and directed.

S&F 32 mm bore waste coupling of PTMT (half or full threaded) (Minimum weight 45 Gram) complete all as specified and directed.

Demoletion and breaking up drain pipes upto 110 mm dia (salt glazed ware, AC, PVC or reinforced concrete) set in cement mortar under floor / fixed to walls etc complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed in trenches complete all as specified and directed.

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore dia of outlet of pipe complete all as specified and directed.

S&F PVC (SWR) gully trap 125mm/110mm setting and jointing with solvent cement and making good of disturbing gound with PCC 1:2:4 in repair complete all as specified and directed.

S&F stack clamps for 110 mm dia pipes, out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof in repair complete all as specified and directed.

S&F stack clamps for 75 mm dia pipes, out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including pillar etc. complete all as specified and directed.

M&L brick work with burnt Bricks type 'B' bricks straight or curved on planot exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Taking down plastering in cement mortar on brick or stone wall/ ceilings etc including racking out joints hacking for key scrubbing down with water etc. complete all as specified and directed.

M&L rendering 15 mm thick cement plaste on fair faces of brick work / concrete surfaces in cement mortar 1:4 finished fair and even complete all as specified and directed.

M&L rendering 15mm thick in cement mortar 1:4 on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15mm thick on fair faces of brick work in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 10 mm thick in cement mortar 1:3, on brick work or concrete surfaces for laying vertical tiles or on ceiling surfaces complete all as specified and directed.

All as per ser item No. 103 here-in-before but 20 mm thick in two layer (10 mm each) rendering on ceiling / Chajja and Facia of roof projections etc in cement mortar 1:3.

M&L applying two coats of oil bound distemper over a coat of primer over a coats of wall care putty (01 mm thick) including preparation of new plastered wall surfaces complete all as specified and directed.

M&L preparing newly plastered/ unplastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls etc., and applying three coats of white wash complete all as specified and directed.

M&L applying two coats of oil bound distemper over a coat of primer over a coat of wall care putty (01 mm thick) including preparation of newly plastered ceiling surfaces complete all as specified and directed.

M&L preparation of old decorated surfaces of walls including brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss and efflorescent salts and trading oil, greasy spots and apply Two coat distemper oil emulsion on walls complete all as specified and directed.

M&L applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over new surfaces complete all as specified and directed.

Dismantling brick tiles or terracing tiles laid in single layer on roofs jointed and pointed in cement mortar complete all as specified and directed.

Demoletion of mud phuska in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and directed.

M&L 10 mm thick screed plaster in cement mortar 1:4 on top of roof complete all as specified and directed.

M&L applying tack coat of industrial bitumen 85/25 at the rate of 1.20 kg per Sqm including cleaning surfaces complete all as specified and directed.

S&F 50 micron polythene film including preparation of roof surfaces complete all as specified and directed.

M&L 80 mm thick average consolidated thickness, mud phuska on flat roofs including 25 mm thick mud plaster complete all as specified and directed.

M&L 40 mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar 1:3 mixed with 5 % of crude oil by weight of cement on mud phuska and pointed flush as work proceeds complete all as specified and directed.

M&L except tiles for 40 mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar 1:3 mixed with 5 % of crude oil by weight of cement on mud phuska and pointed flush as work proceeds complete all as specified and directed. Note :- Old serviceable brick tiles retreived by dismantling of treatment vide item No 111 here-in-before to be reused after cleaning.

M&L flush pointing to roof tiles laid flat in cement mortar 1:4 complete all as specified and directed.

Demolition of cement concrete in ground floor not exceeding 15cm thickness (below or above ground level) and removing the demolished material and debris out side of MD land complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6, type C-2 (using 20mm graded stone aggregate) as in plinth protection, shall be laid in 1:20 slope. The concrete shall be laid at a stretch not exceeding 3-meter in length. Joint gap between the adjoining slab, at corners and at junctions of wall shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen of grade 85/25 garde mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3-meter interval at corner and junction walls complete all as specified and directed.

M&L 75 mm thick PCC 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in floor sub base etc complete all as specified and directed.

M&L crushed sand filling under precast interlocking paver blocks and all other similar works complete all as specified and directed.

M&L machine presssed precast concrete interlocking paver block (Coloured) of any shape and size confirming to IS 15658 -2006 of 60 mm thickness, M-35 grade with grey cement and no pigment laid over sand cushning including compaction of paver blocks using surface vibrator all as specified and directed. Note :- Sand cushioning shall be measured and paid for separately under relevant item.

M&L machine presssed precast concrete interlocking paver block (Grey Colour) of any shape and size confirming to IS 15658 -2006 of 60 mm thickness, M-35 Grade with grey cement and no pigment laid dry over sand cushion complete all as specified and directed. Note :- Sand cushioning shall be measured and paid for separately under relevant item.

Demolition of cement concrete of any description as in roof padding, coping, chajja / coving and kerbing etc. water tank bases on roof etc. unreinforced (other than ground floor) complete all as specified and directed. Note:- Debris/demolished material to be removed out of MD land or 500 m away from the work place in low lying area.

Supply only integral water proofing compound.

M&L providing cement concrete1:2:4, type B-1, (using 20 mm graded crushed stone aggregate) as in roof kerbs, coping or mud stops, round or chamfered on edges complete all as specified and directed.

M&L PCC 1:4:8, type D2 (using 40 mm graded stone aggregate) as in foundation filling, mass concrete, sunken floors etc complete all as specified and directed.

M&L applying evenly a tack coat of industrial bitumen 85/25 grade @ of 1.2 Kg/Sqm including cleaning of surfaces complete all as specified and directed.

M&L rendering 10 mm thick in cement mortar 1:4 on fair faces of brickwork or concrete surfaces, with using liquid water proofing compound @ 200 ml per 50 kg bag of cement or as per manufracture's instructions, complete all as specified and as directed. Note: WPC shall be measured and paid for seperately under relevant item.

Demolition/ dismantling of roofs projection, down facia, floors (other than ground floors), beams, staircases, landing, chajjas and similar cement concrete is reinforced (reinforcement cut as required to facilitate demolition) suspended work upto double storey building and making good to the dismantled portion with cement mortar 1:3 complete all as specified and directed. Note :- Cost of scaffolding shall be deemed inclusive in quoted rate.

Dismantling PVC water tanks capacity exceeding 500 litre and not exceeding 1000 litre complete all as specified and directed.

M&L 1000 litre capacity rotational moulded polyethylene water storage tanks (cylinderical vertical wit closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F gun-metal globe or gate valve 15mm size with iron wheel screwed both end for iron pipe and fixed in repair complete all as specified and directed.

S&F gun-metal globe or gate valve 20 mm size with iron wheel screwed both end for iron pipe and fixed in repair complete all as specified and directed.

S&F ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe of size 20 mm dia in repair complete all as specified and directed.

S&F 5 mm thick coloured of any selecetd design hollow PVC wall cladding strips interlocked to each other fitted to wall including PVC 'U' shapes at top/ bottom and PVC angles at windows/door openings all as per manufacturer’s fixing instructions complete all as specified and directed.

S&F Gypsum board 6mm-7mm thick in ceiling fixed with screw 60cmx60cm placed in ceiling (Angle 25mm X 25mm, Main tee 38mmX23mm ,Sub tee 23mmX23mm) including Aluminium anodised snap grid frame 605 mm X 605 mm for false ceiling including hanging arrangement complete all as specified and directed.

S&F anodised Aluminium snap grid frame work for false ceiling complete all as specified and directed.

M&L providing and fixing Gypsum board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed.

Surface dressing not exceeding 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide & not exceeding 1.5m in depth for foundation etc or manholes & getting out soft/loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) each not exceeding 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick, complete all as specified and directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in hard dense soil complete all as specified and directed.

M&L nominal mix cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L RCC 1:2:4, type B1 (using 12.5 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L RCC 1:2:4, type B1 (using 12.5 mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L formwork to sides of pillars, posts, struts, piers, columns and stanchions square, rectangular surfaces of concrete complete all as specified and directed.

M&L cement concrete 1:5:10, type E2 (using 40mm graded stone aggregate) as in foundations, filling and mass-concrete complete all as specified and directed.

M&L Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12 mm thick in cement mortar 1:3 and pointing with white cement 1:2 using marble dust with admixture of pigment to match with shade of granite including nosing complete all as specified and directed.

S&F mild steel bars 10mm dia and over, cut to length, bent to shape as required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per ser item No. 153 here-in-before but 6mm to 8mm dia bars, as in stripps.

S&F rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging; also fastening & fixing complete GDE Fe410-0 or Fe 310-O complete all as specified and directed.

M&L posts and struts of square/ rectangular mild steel tubes/ angle irons etc complete all as specified and directed.

M&L rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates complete all as specified and directed.

S&F mild steel plates (plain or chequered) of specified thickness etc, channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-290-E-165 complete all as specified and directed.

M&L pre-painted galvalume Aluminium Zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L Hardcore of gauge not exceeding 63 mm, of broken bricks/ brick bats (100 mm thick) etc deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Dismantling of wall and ceiling boards (Fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Taking down carefully Copper /Aluminium point wiring (light, fan, socket or power) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keetping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L point wiring complete with 1100 Volts grade PVC insulated unsheathed FRLS cable of Copper conductor, multi stranded of size 1.5 Sqmm, single core, in and including rigid non-metallic PVC conealed conduit, with all accessories if required such as bends, reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks (for housing lamp holders and light fittings etc) and existing MS pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 Sqmm unsheated stranded Copper conductor with green PVC insulation connected to common earth dolly complete all as specified and directed for the followings :- (a) One light/fan/Bell Point controlled by one single pole one way switch.

(b) One socket outlet on the same board controlled by one single pole one way switch

(c) One 5 Amps socket outlet independent controlled by one single pole 5 Amps switch.

All as per ser Item No. 163 here-in-before but one three pin 15 Amps switch socket out let on the independent board with 2.5 Sqmm PVC insulated Copper conductor and 2.5 Sqmm Copper conductor for continuous earthing complete.

S&F switch piano flush type single pole one way 5/6 Amps complete all as specified and directed.

S&F switch piano flush type 15 Amps, single pole one way complete all as specified and directed.

S&F socket outlet 2 in one, 5/6 Amps flush type complete all as specified and directed.

S&F socket outlet, 2 in one 6 pin 5 and 15 Amps piano flush type complete all as specified and directed.

S&F bell push flush type 5 Amps complete all as specified and directed.

S&F ceiling rose, PVC/Polycarbonate, isolated three terminals complete all as specified and directed.

S&F lamp holder PVC/Polycarbonate, isolated with back plate suitable for batten fittings including 10 Watt LED bulb omplete all as specified and directed.

S&F bell ding dong type AC 230 Volts single pole complete all as specified and directed.

S&F stepped type electronic fan regulater flush type on the existing phenolic laminated sheet etc. as required in repair complete all as specifed and directed.

S&F exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230 Volts, 50 Hz, 1200 RPM, Copper winding of sweep 300mm complete all as specified and directed.

S&F sheet metal enclosures with socket plug top and MCBs single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 20 Amps complete all as specified and directed.

S&F LED tube light fitting 1 X 18 Watt decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 230 Volts, with all accessories internally pre wired and including connecting up with twin core twisted flexible Copper conductor cable with suitable size complete all as specified and directed. Make: Cat Part No LHEXBLP7UN1W018 Make - Havells or techno-commercially equivalent to Crompton/Bajaj/Philips

S&F LED light fitting mirror type with high output diffuser 2 feet, 10 Watts 220 Volts AC decorative type with driver holder and LED lamp including connecting up with three core flexible Copper conductor cable of suitable size complete all as specified and directed.

S&F LED street light fitting 35 Watts 230 Volts, AC outdoor type with high pressure die cast Aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S&F sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series TPN DBs (Vertical type) fitted with ABS frame and 415 Volts 200 Amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and directed.

S&F sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 Volts 200 Amps rated bus bar, Neutral link, Earth bar and Din rail, 8 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and directed.

S&F MCCB 100 Amps, 415 Volts, 16 KA, 4 Pole complete all as specified and directed.

S&F MCB, single pole 240 Volts, 6 - 32 Amps 10 KA 'B Series complete all as specified and directed.

S&F MCB, single pole and neutral 240 Volts, 32 Amps 10 KA complete all as specified and directed.

S&F MCB single pole (SP) 240 Volts, 40 Amps, 10 KA 'B' Series in rpair complete all as specified and directed.

S&F sub main wiring of 4 Sqmm PVC insulated unsheathed FRLS cable multistranded Copper conductor with earth wire of 4.0 Sqmm PVC insulated unsheathed FRLS cable multistranded Copper conductor including PVC conduit pipe 25 mm dia complete all as specified and directed. Note: Two run of single core 4 Sqmm cable and one run single core 4.0 Sqmm cable for earth wire and including conduit pipe 25 mm dia shall measured as one length.

M&L sub main wiring with two single core PVC insulated FRLS cable with Copper conductor unsheathed cable of size 2 x 6 Sqmm drawn through in and including PVC Concealed with 1 x 6 Sqmm PVC insulated Copper conductor single core for continuous earthing complete including PVC conduit 25 mm dia complete all as specified and directed. Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0 Sqmm and one run of 6.0 Sqmm PVC insulated Copper conductor single core, one run of PVC conduit shall be measured as single run.

M&L earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm and 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 m below the ground level with top edge of earth plate at a depth not less than 1.5 m below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. Provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC 1:3:6, type C-2 (using 40 mm graded stone aggregate). The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete 1:2:4, type B-1 (using 20 mm graded stone aggregate), excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009) complete all as specified and directed.

Supply and lay cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) 1100 Volts grade with stranded Aluminium conductor of size 25 Sqmm 4 core complete all as specified and directed.

M&L sand filling under floors, foundation or cable protection including spreding leveling in layer not exceeding 25cm thick complete all as specified and directed.

M&L bricks, common burnt clay building bricks, sub-class ‘B’ designation 75 laid dry width wise across the line of cable in trenches for protection of underground cable complete all as specified and directed.

M&L mild steel galvanised iron pipe light grade (ISI marked) 40mm bore for passing of earth lead laid in trenches fixed to walls laid under floors, roads including all fittings i.e mild steel clamps nuts & bolts etc as required complete all as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 Volts, 1200 mm sweep minimum air delivery 210 CFM with service value 6.00 BEE, Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded Aluminium conductor of size 10 Sqmm 2 core complete all as specified and directed.

S&F LED tube light fitting 9 Watts batten type fixed on wall/ ceiling etc. including connecting up with twin core twisted flexible Copper conductor cable with suitable size complete all as specified and directed.

S&F LED luminaire 600mm x 600mm, 35/36 Watts, 220 Volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible Copper conductor cases of suitable size complete all as specified and directed. Make: Cat part No. LCTLRN-36-FO-CDL of Crompton or techno-commercially equivalent in Havells/Bajaj/Philips

CHETAK CONSTRUCTION COMPANY