PROVN OF 01 X TOILET BLOCK NEAR BLDG NO P-19(OFFICE COMPLEX) OF 665 ARMY AVIATION SQN (R AND O) AND ADDN / ALT OF DRAIN COVERS IN DISPERSAL AREA AT CAATS UNDER GE NASIK ROAD

Amount

Demolition of Brick work or stone/boulder masonry, built in CM including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level)

Dismantling wrought iron or mild steel work of any description and in any position complete all as directed by Engr-in-Charge.

Surface dressing n exc 15 cm deep in soft/loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for pipe line etc and getting out in soft / loose soil complete all as specified and as directed by the Engineer - in - Charge.

M&L for returning filling in of trenches with excavated material in layers of 25 cm including spreading leveling well ramming complete all as directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

M&L for moorum filling under floors or paving laid in layers n.exc 15cm thick, spread , levelled and rammed including watering complete all as specified and directed by Engr-in-Charge.

M&L for PCC(1:4:8) type D-2 using 40mm graded stone aggregate in foundation mass concrete and filling complete.

M&L for PCC 1:2:4 type B2, including necessary formwork using 40mm graded crushed stone aggregate, as in surface channels and drains etc including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed by Engr-in-Charge.

M&L for Deformed steel bars TMT 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hopping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confiring to Fe-410 complete all as specified and directed.

All as per item No.12.00 above but 5mm dia and over upto and incuding 10mm dia in stirrups tie, spacers and binder complete all as specified and directed.

M&L for form work to sides of concrete foundations,footings bases of coloumns raft and raft beams,sides and soffits (if any) of foundation and plinth beams, and similar work,vertical or to batter for rough finished surface of concrete complete all as specified and directed.

M&L for Design mix RCC M-25 (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for form work to sides of pillars, posts,struts,piers,columns etc or to batter for rough finished surface of concrete complete all as specified and directed.

M&L for Design mix RCC M-25(using 20 mm graded stone agg ) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for hardcore broken stone or boulders of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to true surface complete all as specified and directed.

M&L for 75mm thick Plain Cement Concrete (1:4:8) type D-2(using 40 mm graded aggregate as in sub bases to floor complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work n. exc 200mm thick (Horizontal or sloping) complete all as specified and directed.

S&F Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and or reveted, or forgot into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 grade-E-165, complete all as specified.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe 410-W grade-E-250, qulality-A complete all as specified.

M&L for Nominal mix concrete type A-1, M-20 (20mm graded aggregate) laying in floor with screed vibrator including finishing cement concrete surface even and smooth with brooming of top concrete surface complete all as specified and as directed.

M&L for preparing new steel surfaces of any description over 10 cm in width or girth and applying two coats sythetic enamel paint of with one coat red oxide as directed by Engr-in-charge inclnecessary scaffolding and other safety arrangement to work at any height at site if required.

Cutting of construction joints 25 mm deep and 10 mm wide by early entry saw cut using diamond bi cutter of appropriate size, straight and smooth edges. Joint cleaned thoroughly with application compressed air. Joint shall be made dry, vacuum cleaned and free of dirt, oil , vegetation and the debris Application of two coats of primer with thin brush by forward and backward movement at an interval of 30 minutes before placing the backup rod and pouring the sealant. Placing of closed cell medium density, crossed linked polyethylene foam backup rod of 12 mm dia, application of bond breake tape on top of back up rod for complete width of the joint and filled with polyurethane based sealan complying with BS-5212, BS 4254 and EN- 141875- 2003 with minimum movement accommodation factor (MAF) of +I- 30% having minimum 10 year performance guarantee, applying masked tape on the edges of joints and removing the masking tape after filling of sealant as per the method specified by the manufacturer complete as specified and directed

M&L for Design mix RCC M-25 (using 20 mm graded stone agg) lintel beams, roof beams, cantilevers bressumers, lintels over 1.5m span complete all as specified and directed

M&L for Design mix RCC M-25 (using 20 mm graded stone agg ) slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Brick work with fly ash bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for fly ash brick work using old size bricks, straight or curved on plan to any radius, built in CM 1:4 as in half brick thick wall complete all as specified and directed.

M&L for form work to chajjas including edges or to batter for rough finished surface of concrete complete all as specified and directed.

M&L for Design mix RCC M-25 (using 20 mm graded stone agg ) as in chajjas complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finished fair and even complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:6 on other than fair face of brick work or concrete surface complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:4 concrete surfaces of ceiling, chajjas etc. complete all as specified and directed.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite.

M&L for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L for Rounding to edges of stone slabs one edge,such as in steps, cooking platform, and other similar situations

M&L for 15 mm thick cement screed bed in CM 1 : 6 for fixing of tiles complete all as specified and directed.

M&L for Non Skid glazed ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm, in floors set and jointed in cement slurry and pointed in coloured cement complete all as specified and directed.

M&L for 10mm thick backing coat in cement mortar (1:4) on vertical surfaces for fixing of tiles complete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match

M&L for 75mm thick cement concrete 1:3:6 type C-2 (using 40mm graded stone agg) as in plinth protection laid to slope of 1 : 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary form work to divide the area in panels finishing exposed edges fair or rounding or chamfering of exposed edges where directed and providing 6 mm thick joints through the thickness of plinth protection duly filled with mastic filling of one part of hot bitumen 85/25 grade and three parts of fine sand (all by weight) complete all as specified and directed.

M&L for rendering 15mm thick in CM 1 : 4 on roof surfaces finished even and smooth with extra cement complete all as specified and directed using waterproofing compound @ 3% by weight of cement complete all as specified. Note:WPC to be paid separately

Supply only integral waterproofing compound

M&L for Waterproofing on roof including flashing and junctions of parapet,kerb, wall etc.as under :- (a) Cleaning of plasetered roof,parapet,facia surface and applying one coat Oil based cold bituminous primer @ 0.70 kg per sqm. (b) Laying a layer of APP based polymeric membrane,3 mm thick(minimum),weighing not less than 3.60 kg/Sqm prefabricated fire layer waterproofing membrane reinforced with polyester non woven fabric(weighing not less than 160 gms/sqm) shall be applied over compatible primer at 0.40 litre/Sqm of density at 25 degree Centigrade 0.87-0.89 Kg /Litre and viscosity 70-160cps or cold sticker, application of APP modified membrance shall be by torch application. The overlaps shall be minimum 150mm on the transverse direction and 100 mm on the longitudinal direction. (c) Painting the exposed APP membrane surface with bitumastic aluminium paint @ 0.15Kg/Sqm. (d) APP membrance,Primer and bitumastic aluminium paint shall be of same brand.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge over and including stainless steel butt hinges and necessary S S screws complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge over and including M.S. hold fast/ lugs or SS dash fasteners.

S&F for Extruded aluminium alloy handles,150mm fabricated type anodized

S&F Aluminium, 150mm anodized, barrel tower bolts extruded section & fixed

S&F 250mm Aluminium alloy, anodised,sliding door bolt with hasp,stapple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast-aluminium alloy and fixed.

S & F Anodised aluminium frame powder coated(minimum thickness of powder coating 50 mircron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F 3.00 mm thick figured glass, pin head type and glazing with oil putty in squares in not exc 0.5 sqm in each pane complete all as specified and directed.

S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

M&L for preparation of newly plastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of primer.

M&L for preparation of newly plastered surfaces of wall and applying two coats of distemper over a coat of primer.

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of distemper over a coat of primer.

S&F 20mm dia, Brass chromium plated tubular towel rail, D type, 60cm long with flanges

S&F in repair vetreous china wash down water closet pan EWC (pedestal pattern), white (excluding flushing cistern and flush pipe) complete all as specified.BIS approved.

S&F plastic seat cover white closed pattern with flat bottom and cover with mild steel chromium plated or alluminium hinging device complete all as specified and directed.

M&L for table top WHB jaquar cat part No JDS-WHT-25907N

S&F PVC valveless, syphonic action type, flushing cistern of 10 Ltr capacity, low level, white, with inlet, ball valve, float and handle including brackets complete including flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cisterns complete all as specified and directed.BIS approved.

S & F Vitreous China urinals, half stall type (back or corner wall type), white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement;including brackets, flush pipe, CP urinal spreader, grating union, , union and cap and discharge pipe; complete all as specified.

M&L for PVC Nahani trap with grating including incl joining to waste pipe dia of outlet 75mm fixed in cement concrete type B1, (1:2:4) all as specified and directed

S&F Pillar cock, fancy type,(Swan neck type, long body) chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for 15 mm bore complete all as specified and as directed by Engineer-in-Charge. Specification as per SSR Part-I.

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

M&L for brass CP angle cock heavy duty 15mm dia capstan head complete all as specified and directed.BIS approved.

S&F fancy bib taps 15mm bore chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.specification as per SSR Part-I.

Supply and fix 50 mm bore Galvanised Steel water tubing, (ISI Marked) medium grade, with and including all fittings and fixtures such as GI bends, tee,unnion etc,in trenches/on wall complete and connecting to water supply pipe line and testing all as specified and as directed by the Engineer-in-Charge.

All as per Item No. 70.00 above but size 20 mm bore

Supply and fix 50 mm Gun metal globe or gate valves,(ISI marked ), with iron wheel head screwed both end for iron pipe and fixed for (externally threaded),for iron pipe or for union a fixed.

M&L for 20 mm dia gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe all as specified and directed.BIS approved.

M&L for bottle trap brass chromium plated screwed down high pressure screwed both ends for iron pipe of bore 32 mm or for union and fixed Make Jaguar or equivilent all as specified and directed.

Supplying and laying of 16 mm OD CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified. Note. Internal plumbing shall be concealed quoted rate deems to be included of the said provision.

Supplying and laying of 16 mm OD CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified. Note. Internal plumbing shall be concealed quoted rate deems to be included of the said provision.

S & F 1000 Ltr capacity Rotational moulded polye thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

S&F for PVC (SWR) 110mm dia pipes single socketed in any length with rubber ring joints, laid in trenches or in floors all as specified and directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls for 75mm dia pipes complete all as specified and directed.

S&F for PVC (SWR) vent cowl for 110mm bore pipe complete all as specified and directed.

S&F PVC (SWR) junction single, (Single T) equal or un equal for 110mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius for 75mm bore complete all as specified and directed.

All as per item No. 82.00 above provided with acess door .

S&F PVC (SWR) bends any radius for 110mm bore complete all as specified and directed.

All as per item No.84.00 above provided with acess door .

M&L for PVC(SWR) gully trap 125/110mm setting and jointing in solvent cement

M&L for reinforced concrete pipe class NP2, laid and joined complete with collars 150mm bore of pipe.

S & F Factory made RCC manhole covers grade designation LD 2.5, clear opening of frame 450X900mm ISI marked (IS 12592:2002).

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L for Construction valve chamber with bricks masonry of size 60 cm x 60 cm x 60 cm (internal dimension) with 15 cms thick foundation using PCC (1:4:8), type D2, using (40 mm graded stone aggregate), 23 cm thick brick walls built in cement mortar (1:6), 10 mm thick plaster in cement mortar (1:4) on internal and external surface (above ground level), finished even and fair without using extra cement 5mm thick MS sheet cover including 40 x 40 x 6 mm thick angle iron frame fixed on 150 mm thick PCC (1:2:4), type B1, using 20 mm graded stone aggregate) as in including 25 mm x 6 mm flat iron hold fasts, handles, hinges with locking arrangement and applying two coats of synthetic enamel paint over one coat of red oxide primer to steel surface including excavation earthwork in hard / dense soil returning filling in. disposal of surplus soil to a distance n. exc 50 mtr outside MD land etc, complete all as specified and directed

M&L for Boring of holes under road, pavement, hard standing by trenchless technology using ultra sound technique and necessary machine for water supply pipe line upto dia 50mm dia suitable for 0.4 Mpa working pressure complete all as specified and directed.

M&L for point wiring complete with and including single core PVC insulated unsheathed flexible bright multistranded copper conductor cables 1.5 Sqmm, 1100 volts grade FRLS type drawn through & including heavy duty/grade PVC non -metallic PVC conduit and it accessories such as tee elbow, jointer, elbow corner, junction box etcconcealed in walls, columns/beams by means of cadmium plated screws and sunk cup washers along with 1.5 sqmm PVC copper conductor cable as a earth continuity earth wire & connected to commen earth dolly at one end and metallic bodies at other end including adequate size of PVC boards for mounting switches, sockets fan regulator etc for One light point and one fan point controlled by one, one way swtich all as specified & directed by Engineer-in-charge.

All as per Item No. 92.00 but One 5 Amp 5 pin socket outlet point on independent board with ofter switches including earth wire as specified.

Supply and fix switch piano flush button type 5 Amps single pole one way .

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F LED light fitting 10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers.

Supply and fixing of 35 Watt LED Street light 230V AC outdoor type with high pressure die cast aluminiuam housing and heat resistance complete with driver, lamp bracket with impact and corrosion reistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specfied and directed by Engr-in-charge.

Supply and fixing socket combination 2 in 1, 5 Amp flush type complete all as specified.

Supply and fix ceiling rose surface PVC 50mm dia 3 terminals including PVC mounting block white/ivory finish.

Supply and fixing distribution board sheet metal enlosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & MCB's 240volts, 200 Amp rated bus bar with front openable cover suitable for SP & N 8 ways all as specified & directed.

Supply and fixing of MCB SPN 6-32 Amps, 230 Volts, 50 Hz with 10 KA .

Supply and fixing of MCB SP 6-32 Amps, 230 Volts, 50 Hz with 10 KA .

Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty cable with PVC insulated stranded aluminium condcutor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and over all PVC sheathed of size 10 Sqmm 2 core complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6.3 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level connecting to the GI wire 4.0 mm dia, by means nut bolt, nuts, check nuts and washer of the GI Earth wire protected by provision of GI light grade pipe 15 mm, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, taste point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified incl testing on completion”.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 3750.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

Alpha Construction (BID ID -3456112)

MANOVANDANA CONSTRUCTION (BID ID -3453855)

M/S R.K.S. CONSTRUCTION (BID ID -3456444)