REPAIR/ MAINT AND REPLACEMENT OF OLD RUSTED EXTERNAL WATER SUPPLY PIPE LINES WITH OTHER CONNECTED WORKS AND REPAIRS/ MAINT AND REPLACEMENT OF ELECTRIC STORAGE HEATERS (GYSERS) AND SOLAR WATER HEATERS AND ALLIED WORKS AT AF STN ADAMPUR

Amount

Excavation in trenches in soft/loose soil not exceeding 1.50 metre wide and not exceeding 1.50 metre in depth; for foundation, etc. and getting out complete, all as specified & directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick each, complete, all as specified & directed.

Removing excavated spoil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete, all as specified & directed.

M&L for PCC type C-2 (1:3:6), using 40 mm graded crushed stone aggregates as in filling & mass concrete, complete all as specified and specified & directed.

M&L for PCC type D-2 (1:4:8), using 40 mm graded crushed stone aggregates as in filling & mass concrete, complete all as specified and specified & directed.

M&L for 100 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of shape approved by GE, made by table vibratory method using PU mould, laid in required pattern over and including 50mm thick compacted bed of coarse sand, compacting through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and specified & directed.

Boring holes under roads, paths, hardstanding, pavements, taxi track of any desciption by trenchless technology using ultrasound technique or by manual boring method of hole technique for passing pipe lines complete all as specified & directed for the followig bore of pipe : -

15 to 50 mm bore.

80 to 200 mm bore.

NOTES APPLICABLE TO SERIAL ITEM 1 To 3 & 7: (a) Excavation work shall be carried out manually only. (b) LT/HT cable, water supply/ sewage/telephone lines, if any, get damaged during excavation & earthwork, demolition of PCC shall be repaired by the contractor immediately as per existing specifications to the entire satisfaction of Engineer-in-Charge.

M&L for Ductile iron pipes, class K-9, centrifugaly cast, flanged ends, ISI marked in any length with & including rubber or fibre board gasket joints laid in trenches, ducts complete all as specified & directed for the followig bore of pipe : -

100 mm bore

150 mm bore

200 mm bore

M&L for Ductile iron pipes, class K-7, centrifugaly cast, spigot & socket ends, ISI marked in any length with & including push on joints laid in trenches, ducts complete all as specified & directed for the followig bore of pipe : -

100 mm bore

150 mm bore

NOTE APPLICABLE TO SERIAL ITEM 8 & 9:- Excavation and earthwork & CI/DI fittings will be measured and paid for separately under respective item of ‘BoQ’.

M&L for DI specials/ fittings of any type, radius, angle, tapers, increasing, decreasing sockets, tees, tail pieces and collars etc complete all as specified & directed.

Dismantling and taking out existing under ground CI/DI pipes, Spigot and socketed / flanged/screwed ends of any length & type, including necessary fittings, burning of lead/rubber joints if any and bailing out water complete all as specified & directed for the followig bore of pipe : -

80 mm bore

100 mm bore

150 mm bore

200 mm bore

Relaying serviceable CI/DI pipes of any description (after cleaning) with necessary fittings, in trenches, ducts complete all as specified & directed for the followig bore of pipe : -

80-100 mm bore

150 mm bore

200 mm bore

NOTE APPLICABLE TO SERIAL ITEM 11 & 12 :- Excavation and earthwork will be measured and paid for separately under respective item of ‘BoQ’.

Cutting the existing CI/DI pipes in position for inserting new pipe attachment/ tees or for making new branches etc. with joints & jointing material, including necessary excavation & earth work complete all as specified & directed for the followig bore of pipe : -

80 mm bore

100 mm bore

150 -200 mm bore

M&L for Run lead joint including jointing material like spun yarn, caulking lead & tools etc IN REPAIRS, complete all as specified & directed for the followig bore of pipe : -

80 mm bore

100 mm bore

150 mm bore

200 mm bore

M&L for Joint with rubber or fibre board gasket including provision of bolts, nuts, washers and white lead or mineral oil etc IN REPAIRS, for CI/DI flanged pipes complete all as specified & directed for the followig bore of pipe : -

100 mm bore

150 mm bore

200 mm bore

M&L for D' Joint with two numbers of round rubber 'O' rings and one DI/GI flate 'O' ring including necessary bolt, nut and washer, IN REPLACEMENT, for DI/GI pipes complete all as specified & directed for the followig bore of pipe : -

80 mm bore

100 mm bore

150 mm bore

200 mm bore

M&L for Repairing GI/CI pipe line, upto 200 mm bore of any descripton to prevent leakage of water by welding to the entire satisfaction of Engineer-in-Charge including necessary excavation & earth work complete all as specified & directed

M&L for Rectification of leakage in CI/DI pipe line making it leak proof to the entire satisfaction of Engineer-in-Charge by filling jointing material etc.including necessary excavation & earth work complete all as specified & directed for the followig bore of pipe : -

80-100 mm bore

150-200 mm bore

M&L for Cast Iron Sluice valve flanged Type, class PN 1.6, ISI marked (IS- 14846-2000) with stainless steel spindle flanged both ends drilled CI gate with brass ring and iron wheel handle including necessary flanged joints & jointing material, IN REPLACEMENT suitable for DI/CI pipe complete all as specified & directed for the followig bore of pipe : -

80 mm bore

100 mm bore

150 mm bore

200 mm bore

M&L for Cast Iron Non return/Reflux valve flanged Type, class PN 1.6, ISI marked (IS- 14846-2000) with stainless steel spindle flanged both ends drilled CI gate with brass ring and iron wheel handle including necessary flanged joints & jointing material, IN REPLACEMENT suitable for DI/CI pipe complete all as specified & directed for the followig bore of pipe : -

80 mm bore

100 mm bore

150 mm bore

M&L for CI foot valve, flanged type, ISI marked, with flanged joint & jointing material, IN REPLACEMENT for CI/DI pipe complete all as specified & directed for the followig bore of pipe : -

40-50 mm bore

65 mm bore

100 mm bore

150 mm bore

M&L for Construction of brick masonary valve pit with and including MS sheet cover fabricated from 3 mm thick MS sheet and frame of angle iron 40 mm x 40 mm x 5 mm with fixing arrangement hinges and locking arrangement and painting two coats of synthetic enamel paint over a coat of red oxide primer on MS cover and frame including necessary excavation and earth work in any type of soil, returning, filling in approved soil, disposal of surplus soil to a distance not exceeding 50 metre, 150 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation, brick work using pulverised fuel ash lime bricks in cement mortar 1:6, 15 mm plastering in cement mortar 1:4 both internally and externally, 100 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in flooring complete all as specified, including demolition of existing valve pit having internal size: --

M&L for Drilling and tapping CI/DI/GI water mains (in position) for branch connections with & including provision of suitable size ferrule & GI nipple including necessary excavation & earth work complete all as specified & directed for the followig bore of pipe : -

15 mm bore

20 mm bore

M&L for Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of aluminium paint complete all as specified and directed.

S&F Steel tubes ‘medium grade’, ISI marked, galvanized with all fittings, laid in trenches including taking up or down existing unserviceable steel tubing and connections, complete all as specified & directed for the followig bore of pipe : -

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

NOTE:- Excavation and earthwork will be measured and paid for separately under respective item of ‘BoQ’.

S&F Gun metal globe/gate valve, with ron wheel head, ISI marked (IS:9890), screwed both ends for GI tubes, IN REPLACEMENT, complete all as specified & directed for the followig bore of pipe : -

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

S&F Precast RCC pipe line route marker of dimension 1000mm x 300mm x 80mm including painting one coat red/ yellow paint, write size of pipe & type of pipe as with black paint in block letters of size 10mm and mounting the route marker on ground with PCC (1:4:8) bedding upto a depth 25cm below ground level including excavation of soil 300mm x 300mm x 250mm below ground level complete all as specified and directed.

S&F Electric Decrine dozing pump single phase 60 watt, 415 volt 50 cycle per second for chemical dozing pump IN REPLACEMENT complete all as specified & directed.

Servicing, greasing and recalibration of chlorine dosing pump as per manufacturer's maintenance reference to the entire satisfaction of Engineer-in-Charge. NOTE:- Supply only spare parts will be measured and paid for separately under respective item of BoQ.

Supply only the following parts of chlorine dosing pump :-

Gear motor 230 v 50 Hz Make:- Declibac Cat pat No.- PM682CE

Rotor assembly with bearing brackets & tolerance ring

Rotor assembly ( Roller each pocket 4 Nos)

Pump tube ( tube each pocket 5 Nos)

Weighted suction line starter 3/8''

White suction / discharge tube 3/8''

Check valve duckbill only ( 5 Nos Each pocket)

Connecting nut 3/8''

Connecting nuts 3/8'' with adaptor ( 5 Nos Each pocket)

Ferrule 1/4'' ( 24 Nos each pocket)

S&F FRP container of capacity 100 litre with top cover white colour, IN REPLACEMENT, complete all as specified & directed.

S&F Chlorine mixing assembly with saft and propeler, IN REPLACEMENT, complete all as specified & directed.

S&F Tolodine solution in 500 MI bottle, IN REPLACEMENT, complete all as specified & directed.

Chemical analysis including micro biological examination of water sample obtaining from bore well at pump house No-1 to 12 and 2 Nos STP under GE (AF) Adampur. Collect the sample as per standard operating procedure from bore well and STP as chemical and microbiological as per the IS specification. NOTE:- (i) The complete analysis report should be submitted within specific period. (ii) Bore well & STP should be test from NABL approved lab as approved by GE.

Taking down & Re-winding of electric motor 3 phase 60 watt capacity any make with super enamelled copper winding wire of adequate size and gauge, varnishing, drying as per original specifications including repair in REPLACEMENT of GM bushes/ bearing, re-fixing and testing on load etc. complete all as specified & directed.

Cutting grass, vegetation, shrubs, bushes, small trees etc inside the installation, manually to the entire satisfaction of Engineer-in-Charge including sweeping and removal of entire rubbish/cut grass/ vegetation etc. outside MoD land complete all as specified & directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not excceding 15cm thickness (above or below ground level) complete all as specified & directed.

NOTE:- (i) To maintain utmost security at AF Station, contractor will arrange his workmen along with T&P in a manner that nonfunctional water supply line and connected items is made functional swiftly within 24 hour of receiving of complaint from the MES, during entire contract period.

GYSER

Disconnectiing & taking down water storage geyser for repair etc. from existing location and refixing & reconnecting the same on orginal or new location after repair complete, of the following capacities:-

25 litre

35 litre

50 litre

NOTE: Repair / Replacement of unserviceable spare parts/ items and painiting as specified will be measured & paid for under serial item No. 43.00 to 43.23 here-in-below as required & where directed.

Dismantling/ taking out of inner storage hot water tank , geyser assembly, heating element , glass wool etc from in side the geyser of capacity 25 /35/50 litre and including remove blockage / depositing the scale, silt, sludge, dirty particles material from the inside of the storage heating system through method of descaling with chemical acid or manually mechanically system and after washing in side of the storage heating tank, geyser assembly, heating element, thermostat system including tighting, adjustment, servicing and also rectification the leakage problem of hot tank through hot & cold welding / brazing (gas or electric welding) work system for steel tank / copper tank complete and after repair re-assembly and proper filling the glass wool and replacement of defected items in side around the tank complete. NOTE: Repair / Replacement of unserviceable spare parts/ items and painting will be measured & paid for under serial item No. 20.00 to 20.23 here-in-below as required & where directed.

Replacement of the unserviceable articles/parts of water storage geyser as required & where directed as under: -

Supply only Heating element of copper / brass alloy round , triangular, round with threaded type shape / alongwith 'O' ring washer as per existing size sample / model for rating 1.5 kW complete.

Supply only Heating element of copper / brass alloy round , triangular, round with threaded type shape / alongwith 'O' ring washer as per existing size sample / model for rating 2 kW complete.

Supply only Copper/brass alloy round shape /size as per existing sample/model type special electric geyser heating elements of rating capacity 2 KW with having U cut shape of heating rod and round base with round ring washer and alongwith having thermostate base rod including numbers of hole for adopting of geyser thermostat purpose suitable for using in MAP qtr installed electric geysers system IN REPLACEMENT complete.

Supply only Inner cold and hot water circulating apparatus unit assembly (Geysers assembly) alongwith replacement of defected nuts and bolts and rubber check washer, split gas pin system complete, for geyser capacity 25 Litre

Supply only Inner cold and hot water circulating apparatus unit assembly (Geysers assembly) alongwith replacement of defected nuts and bolts and rubber check washer, split gas pin system complete, for geyser capacity 35 Litre

Supply only Inner cold and hot water circulating apparatus unit assembly (Geysers assembly) alongwith replacement of defected nuts and bolts and rubber check washer, split gas pin system complete, for geyser capacity 50 Litre

Supply only Gun metal vertical type non return valve of size 15 mm bore complete.

Supply only Hot water inner tank made out of heavy duty stainless steel sheet metal body system alongwith nuts and bolts and rubber joint washers for storatge type geyser capacity 25 Litre complete.

Supply only Hot water inner tank made out of heavy duty stainless steel sheet metal body system alongwith nuts and bolts and rubber joint washers for storage type geyser capacity 35Litre complete.

Supply only Hot water inner tank made out of heavy duty stainless steel sheet metal body system alongwith nuts and bolts and rubber joint washers for storage type geyser capacity 50 Litre complete.

Supply only Adjustable setting type thermostat made out of copper / brass alloy metal for storage type geyser capacity 25-35 Litre complete

Supply only Adjustable setting type thermostat made out of copper / brass alloy metal for storage type geyser capacity 50 Litre complete

Supply only Capilary setting type thermostat made out of copper / brass alloy metal for storage type geyser capacity 25 Litre complete

Supply only Air safety valve for storage geyser of capacity 25 ltr to 50 Litre complete

Supply only Insulating material i.e. glass wool for filling inside area in between of geyser outer body and hot water tank system including dismantling of geyser for capacity 25 to 35 Litre complete

Supply only Insulating material i.e. glass wool for filling inside area in between of geyser outer body and hot water tank system including dismantling of geyser for capacity 50 Litre complete

Supply only Mild steel outer cover top plate duly spray painted with super enamel paint over a coat of red oxide primer complete for 25 to 35 Litre capacity storage geyser.

Mild steel outer cover top plate duly spray painted with super enamel paint over a coat of red oxide primer complete for 50 Litre capacity storage geyser.

Supply only Mild steel outer bottom cover plate duly spray painted with super enamel paint over a coat of red oxide primer complete for 25 to 35 Litre capacity storage geyser.

Supply only Mild steel outer bottom cover plate duly spray painted with super enamel paint over a coat of red oxide primer complete for 50 Litre capacity storage geyser.

Supply only Mild steel outer body cover duly spray painted with super enamel paint over a coat of red oxide primer complete for 25 to 35 Litre capacity storage geyser.

Supply only Mild steel outer body cover duly spray painted with super enamel paint over a coat of red oxide primer complete for 50 Litre capacity storage geyser.

Supply only Indicating lamp Red /Green round & square shape display for geyser on / off indicating system complete all as specified.

NOTE FOR SERIAL ITEM 43.01 TO 43.24: The size/make/ model/nomenclature above mentioned new items shall be as per existing item or as directed by Engineer-in-Charge.

M&L for Spray painting to external body of storage geyser of capacity 25/35/50 litre including clamps with first quality synthetic enamel paint of white shade, at site or in store including filling cavities with filler materials and preparation of steel surfaces including marking MES No. with black paint on each geyser complete all as specified and directed.

S&F Heavy duty PVC braided PVC connection pipe of size 15 mm dia and 450 mm long alongwith two nos of brass nut and nylon washer IN REPLACEMENT complete all as specified and directed.

S&F Heavy duty steel wire braided chromium plated stainless steel metal body connection pipe of size 15 mm bore and 600 mm long alongwith two nos of brass nut and nylon washer IN REPLACEMENT complete all as specified and directed.

S&F Angle valve suitable for 15 mm bore made out of cast copper alloy chromium plated iron pipe connection IN REPLACEMENT complete all as specified and directed.

S&F Flexible type PVC bedded copper cable of size 2.5 sq.mm 3 core (40/00.0076 type size) 1100 volt grade cable with PVC insulated PVC sheathed with multi stranded copper conductor IN REPLACEMENT complete all as specified and directed

S&F MS sheet metal enclosure assembly with having SPN enclosure and 2/3 pin top plug & earth socket of rating voltage 220 volt AC IN REPLACEMENT complete all as specified and directed.

S&F Cast copper alloy chromium plated bib tap 15 mm size, quarter turn type for iron pipe, IN REPLACEMENT complete all as specified and directed.

S&F Heavy duty MS fasteners of suitable of size 10 mm dia not exceeding up to 100 mm long along with nut, bolt & washer etc including drilling holes grouting on wall for hanging geyser. and making good the disturbed surfaces to the entire satisfaction of Engineer in Charge, IN REPLACEMENT complete all as specified and directed.

Sub main wiring system with having two run of PVC insulated wire of size 2.5 sq.mm FRLSH multistrand copper conductor cable 1100 volts grade drawn into including providing one run of 2.5 Sq.mm FRLSH multistrand copper conductor cable as continuous earth wire for connecting to common earth including taking down existing wiring all as specified.

M&L for Sub main wiring system with having two run of PVC insulated wire of size 4 sq.mm FRLSH multistrand copper conductor cable 1100 volts grade drawn into including providing one run of 4 Sq.mm FRLSH multistrand copper conductor cable as continuous earth wire for connecting to common earth including taking down existing wiring all as specified and directed

S&F Rigid non metallic heavy duty PVC conduit medium grade not less than 20 mm dia ISI marked alongwith all conduit fittings and fixing accessories duly fixed on wall / surface / roof mounting system with the help of saddle with base clamps IN REPLACEMENT complete all as specified and directed.

S&F MCB SP of rating capacity 20 Amp , 220 Volt AC and making electrical connection, IN REPLACEMENT complete all as specified and directed. .

S&F MCB SPN of rating capacity 40 Amp, 220V, AC and making electrical connection, IN REPLACEMENT complete all as specified and directed.

S&F PVC insulated body three pin plug top of rating capacity 15/16 Amp and making electrical connection IN REPLACEMENT complete all as specified and directed.

S&F Switch piano flush button single pole one way 16 Amp, 240 volts IN REPLACEMENT complete all as specified and directed.

SOLAR WATER HEATING SYSTEM WORKS

S&F Copper / brass heating element round & triangular shape size of rating capacity 3/4 KW including along with providing suitable rating / type of thermostat complete set all as per existing size sample/ model and including duly fixed on existing solar heating system, IN REPLACEMENT complete all as specified and directed.

S&F U-Rubber (rubber rectangular paking ) as per existing size / sample suitable for outer cover frame and using for fixing of outer side of each solar heating collector panel plate of capacity 100 LPD system proposed including providing with rubber solution, IN REPLACEMENT complete all as specified and directed.

S&F Round shape type rubber gaskets suitable used for fixing or packing of pipe line attachment system proposed including replacement of suitable size / type of SS nut , bolt washer IN REPLACEMENT complete all as specified and directed .

S&F Heavy duty round 'U' cut shape type rubber groumats as per existing sample / size suitable used for fixing / attachment of inner side of hot copper piping jal system with solar collector plate attechment supporting system proposed including providing of rubber solution complete all as per existing size and type IN REPLACEMENT complete all as specified and directed .

S&F Round shape mild steel blank flanged suitable for 20 mm dia bore pipe line including making of nos of holes alongwith suitable used for fixing of outer side of hot / cold pipeing line attachment system proposed including replacement of defected suitable size / type of SS nut , bolt washer, IN REPLACEMENT complete all as specified and directed .

S&F Aluminium foil rapping work in side of solar heating collector each panel plate system as per existing size and type including providing of adaptor solution material including taking down existing broken/defected aluminium foil IN REPLACEMENT complete all as specified and directed .

S&F Insulation material suitable for filling of inside of solar heating collector panel plate system and solar tank ,and it connecting hot pipe lines system proposed including taking down existing insulation material IN REPLACEMENT complete all as specified and directed.

S&F MS flanges fitted GI nipple of size 20 mm dia up to 4 inch long as per existing size and type IN REPLACEMENT complete all as specified and directed .

S&F Rubber hose pipes of size 20 mm dia ,150 mm long with adhaptor clamp as per existing size and type IN REPLACEMENT complete all as specified and directed .

Testing and commissioning of solar storage warm stainless steel tank with inner heat exchanger system and duly fitted fully insulated materials with outer side aluminium cladding fram work complete system set and including providing alogwith connected suitable type / size rating fixing accessories like temperature gauge , heating element port , inlet and outlet pipe line water connection set IN REPLACEMENT hot tank system all as specified. of capacity: -

200 Litre

500 Litre

1000 Litre

NOTE FOR SERIAL ITEM 69.01 TO 69.03 The size/make/ model/nomenclature of above item(s) shall be as per existing item or as directed by Engineer-in-Charge.

S&F Solar plate toughened heating glass of appoximate size 184 cm long 124 cm wide & 4 mm thick or as per existing size or sample suitable for using / fixing on suitable for solar heating collector plate assembly set of total heating capacity of each plate 100 LPD and duly properly fixed on existing top structure fixing & attachment on existing solar water heating colletor plate assembly system of capacity 200 LPD, 500 LPD & 1000 LPD IN REPLACEMENT complete all as specified and directed .

S&F Aluminium metal sheet as per existing size / gauge suitable for fixing on solar attachment heating system IN REPLACEMENT complete all as specified and directed .

Material and labour for disconnection of electric supply and water pipe line connections and taking out all type of clamp, nut bolt or connected fixing accessories from the existing position of each solar plate from solar heating collector plate system and removing all fixing accessories like aluminum side frame cladding ,heating top glass with rubber packing materials , copper fins with tubing plates jal assembly for the proposed of claening in side / removing blockage / depositing the scale ,sult, sludge, dirt etc particle material from in side of copper tubes jal assembly including cleaning ,checking, serviving , tighting , adjusting and also calibration and descaling through chemical acid solution method / manually mechanically system for making of nos of hole on each blockage copper tube assembly through suitable size of drilling rod with cleaning of wire brush in each copper tubing system and their after duly fill up the all nos of making hole work in copper tubes through hot & cold welding / brazing (gas or electric welding) work system and applying two coats of black bituminous paint over on distrubed place of copper fin and tubing jal system and after circulation of chemical acid solution through proper pressure washing pump in complete entire system and also rectification the leakage problem of entire tube system complete and after repair reaasembly and proper filling the all replacement item like insulation wool and aluminium foiling Glass work in side and around the collector plate system and replacement of defected nut, bolt & washer and fixing on same position and testing on system complete all as specified and directed.

NOTE APPLICABLE TO SERIAL ITEM 72: (i) Spare parts will be measured and paid separately under respective items of BoQ. (ii) Descaling, driiling ,Servicing, adjusting etc and testing run work will be carried out by well qualified techanician having good experience in the about repairing field of solar water heating system .

M&L for Disconnection of electric supply and water pipe line connections and demolation of PCC work and taking out all type of clamp, nut bolt or connected fixing accessories from solar warm tank, PVC storage tank and complete solar collector plate assembly unit with iron structure frame and connected pipe work system complete including removing all fixing accessories like heating top glass with rubber packing materials , copper fins with tubing plates jal assembly from the existing position and shifting to complete system from one place to other place and they after including duly providing welding / brazing work for broken system for fill up the all damage work on iron & in tubes system through hot & cold welding / brazing (gas or electric welding) work and after reassembling on new position by replacement of defected nut, bolt & washer and refixing on same system and testing on load complete all as satisfaction and specified & direction fo EIC NOTE - (i) Spare parts, item of work will be measuresed and paid separately under respective items of schedule 'A'

M&L for Testing and commissining IN REPLACEMENT of of broken / damage unserviceable solar water heating collector plate assembly set complete suitable for solar heating coolector plate assembly of heating capacity 100 LPD and as per collector plate appoximate size 185 cm long 125 cm wide & 11 mm thick or as per existing size or sample suitable for using / fixing & attachment on 200 LPD to 1000 LPD capacity of solar heating system.The outer body of solar collector plate assembly set made out / fabricated aluminium structure frame work along with aluminium clading for all side support frame with U rubber, heating tuffen top glass with rubber packing materials , copper heat exchanger fins with copper tubing plates set jal assembly and duly fully insulated with insulated materials with aluminium foiling work etc and providing with connected suitable type / size inlet outlet pipe connection complete set and including dismantling and taking out of existing old unserviceable plate collector system complete all as specified and directed.

M&L for Disconnecting of electric wire and water pipe line connections & taking out of insulation materials from existing drain out position for the proposed of repairing & descaling of inner steel hot water tank of solar water system and including cleaning & remove blockage / depositing scale, silt, sludge, dirt etc particle material from the in side of the storage steel heating tank system through properly method of descaling ,and washing with chemical acid solution / manually / mechanically system including proper repair in fixing in place of heating element, thermostat system,temperature gauge point including tighting,adjustment, servicing, replacement of defected air release valve rubber gasket and also rectification the leakage problem of steel hot water tank by the help of hot & cold welding / brazing (gas or electric welding) work method complete and after repair reasembly and proper filling the glass wool ,alumium sheet cover cladding work and other replacement items in side / out side/ around the hot tank and pipe line system and after testing of leakage complete suitable of capacity: -

200 LPD to 500 LPD

Galvanised iron medium grade tubes laid under path, on roofs or on walls with all pipe fittings and fixing acessories, IN REPLACEMENT complete all as specified of size:

15 mm bore

20 mm bore

M&L Mild steel work as in staging structure / support frame by cross arms or angle or channel , MS sheet including bracings, supports, clamps and back plates fabricated frame structural steel sections work including nuts, bolts and washers, welding, bending, cold or hot drilling and making holes for bolts in any shape or size and inclusive of one primer coat, one under coat and one finished coat of paint for solar water heating system IN REPLACEMENT complete all as specified and directed.

S&F PVC HDPE rotational moulded water storage tanks (cylidrical vertical type with closed top), triple layered, ISI marked fixed in position and making inlet and outlet water piping line connections, IN REPLACEMENT complete all as specified of size/capacity:-

500 Litre

1000 Litre

S&F Ball brass valve, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule 20mm bore, ISI marked, IN REPLACEMENT complete all as specified and directed.

Demolition for PCC of any description and any position and providing PCC (1:3:6 ) type C-1 using 20 mm stone aggregate work for laying PCC at difference location/ installation including necessary form work and finishing work the exposed faces of concrete even and smooth using extra cement complete all as specified and directed.

Sheet metal enclosure duly powder coated MCB distribution box SPN 2 way with having mounting channel and connection bus bar system fixed flush on wall with cement mortar (1:4) and making all necessary electrical connection, IN REPLACEMENT complete all as specified and directed.

Sheet metal enclosure duly powder coated double door system MCB distribution box SPN 4 way with having mounting channel and connection bus bar system fixed flush on wall with cement mortar (1:4) and making all necessary electrical connection, IN REPLACEMENT complete all as specified.

Applying of two coats black colour superior quality synthetic enamel paint work for all fixing iron attachment support system of complete solar water heating system like staging structure of hot and cold tank,make up tank , solar collector plate fixing support iron assembly suitable for complete solar water heating system of capacity including preparation of surfaces to the entire satisfaction of Engineer-in-Charge and making necessary welding work if required complete all as specified of capacity: -

Water make up tank duly fabricated / made out of 2 mm thik mild steel sheet of suitable of size 400 mm long x 20 mm wide x 25 mm height to make a shape of rectangular type alogwith providing lead 2mm thick mild steel and inclduding making 03 nos of hole for inlet and outlet proposed of water connection system and inserting the suitable size socket 15/20 mm dia alongwith nipple complete all as specified and directed .

Tempreture gauge meter as per existing type sample suitable for measuring rating of water temperture 0 to 120 degree C including duly fixed on exisiting position of system IN REPLACEMENT complete all as specified and directed.

Cleaning of RCC / PVC service tank by art technology ''Tank cleaning'' removing the mud / sludge with pump cleaning the roof, walls and bottom inside & outside by using dirt cleaner and sparying of customised anti bacterial agent on entire surface and drying up properly the complete tank / sump including writing out side the tank as '' Tank cleaned on and capacity'' on black painted surfaces of following capacity : -

200 Litre

500 Litre

1000 Litre

NOTE APPLICABLE TO SERIAL ITEM 86: (i) Disconnect and re-fixing of float valve, inlet and outlet pipe connection including in this item. (ii) Removing of mud disposed to at location mentioned in Schedule 'A' note 5(d).

Supplying, laying, jointing and testing XLPE insulated heavy duty multi stranded armoured and PVC sheathed LT cable 6 Sq.mm 4 core 1100 volts grade with aluminium conductor laid in trenches / walls / ducts/ along poles/ through pipes including taking out existing cable complete all as specified and directed,

NOTE FOR SERAL ITEM 01 to 87 :- Not withstanding with the provision of "Compensation for Delay' envisaged under condition 50 of IAFW-2249, General Conditions of Contracts, additional compensation @ Rs. 500/- per day will be charged from contractor in case he fails to make the functional to the entire satisfaction of Engineer-in-Charge within 24 hour of receiving of complaint from the MES regarding non working above items.

J.K & Company (BID ID -3374294)

Northern cable fault locatoers (BID ID -3373756)