Loading…
Loading…
Tender Value
₹1.9 Cr
EMD Value
₹3.8 L
Closing Date
30 May 2026, 2:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
SOUTH
14 conditions · 2 needing a document upload
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or V whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. Note :- (i) For Joint Venture (JV): The tenderer shall submit credentials as mentioned in Clause 17 of GCC April 2022 (Ammended upto date). (ii) In case, date of tender inviting is on or after date of statutory deadline for audit of balance sheet of previous Financial Year (i.e. 30th Sept. or as further extended for this FY), audited balance sheet of 4th previous year shall not be considered unless concerned CA certifies that balance sheet is not audited yet as on date of invitation of this tender.
The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (a) Three similar works costing not less than the amount equal to 30% of advertised value of the tender, or (b) Two similar works costing not less than the amount equal to 40% of advertised value of the tender, or (c) One similar work costing not less than the amount equal to 60% of advertised value of the tender. Note :- For Joint Venture (JV): The tenderer shall submit credentials as mentioned in Clause 17 of GCC April 2022 (Ammended upto date).
Defination of Similar Work :- Engineering Survey works.
8 conditions · 3 needing a document upload
The tenderer should have prism Gedo / AIMIL / AMBERG or similar trolley measure with them. To ensure it, the contractor must provide documentary evidence of Owning OR Proof of entering into MOU with manufacturer/ supplier of prism Gedo / AIMIL / AMBERG or similar trolley measure. Failing to furnish the documentary evidence in the tender itself, the tender is liable to be rejected.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
1.The quantities/amount mentioned above are rough and for guidance only and are subject to change according to the needs of the railway & variation there of to any extent will not be the basis of any claim against the Railway. 2.The contract shall be governed by General Condition of Contract and Instructions to the Tenders -2022 (Amended up to date). 3.All tools & plants and mechanical equipment as required to execute the work shall be arranged by the contractor. 4.Contractor/ suppliers/ service providers/ parties shall register their firms under EPFO & GSTIN (GST Identification Number).
Pre & post tamping track measurement survey using trolley-based measurement system in the jurisdiction of Sr DEN/S/BKN under control of ADEN/Ratangarh (Total 594.200 Tkm)
21-26-27
21-26-27
Open
Works - General
24 Months
Bikaner, Rajasthan
₹0
₹3.8 L
30 May 2026
8 May 2026
16 May 2026
11 items across 2 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | Above/ 19151083.82 Below/P | ||
| — | 594.20 | — | — | ||
| Pre Tamping Measurements reference points, Establishments of main GNSS (DGPS Base) Point & reference point establishment at 150 meter maximum interval along the track | — | — | — | 35,43,612.71 | |
| — | 594.20 | — | — | ||
| Pre Measurement for tamping with total station & prism Gedo / AIMIL / AMBERG or similar trolley measure and store Gauge, Cross elevation, Chainage, shift and lift value at every 3m i.e. every 5th sleeper interval along the track centre line and coordinates to track centre line at every 3m to be submitted with track geometry (per km/Round). | — | — | — | 62,08,813.63 | |
| — | 594.20 | — | — | ||
| Construct Target / Design alignment with the good points of existing pre measurment profile in design software to export data in ALC format with design alignment of measured reading in M/c and to provide track adjustment file with over extension and also to provide Geo Geometry file to provide text file with slew, uplift and gauge at every 3m i.e. every 5th sleeper interval for tamping machine operator during reference. | — | — | — | 15,96,591.63 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
General Condition
ATTACHMENT
GCC-2022-uptoACS104.3.25.pdf
ATTACHMENT
GCCACS11_compressed.pdf
ATTACHMENT
specialconditions.pdf
ATTACHMENT
ScopeofworkSouth.pdf
ATTACHMENT
Generalcondition01.04.26From01-26-27_compressed.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .