CONVERSION OF OH LINE TO UNDERGROUND HT / LT CABLE) AT AFS PATHANKOT.

Amount

Supplying laying jointing and testing XLPE insulated, PVC bedded, galvanised steel strips armoured heavy duty electric power cable with stranded aluminium conductor suitable for rated voltage of 11000 Volt grade, 3 Core x 95 Sqmm conforming to IS 7098 Part-2) 2011 with upto date amendments and laid in trenches / ducts / pipe or on poles complete all as specified and directed.

Excavating in trenches, not exceeding 1.5metre wide and exceeding 1.5metre depth but not exceeding 3.0metre depth for foundation, etc., and getting out in any type of soil, complete all as specified and directed. Note : If any pipe line / HT / LT cable / sewage lline / fibre cable will damaged during the excavation, the same will be rectify / repacement of damage portion to make refunctioning with in one hour and contractor immiadiate inform to concern authority, and rate will deemed to includedd in the quoted rated.) complete all as specified and directed by Engr In Charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick any type of soil, complete all as specified and directed.

Removing excavated soils to a distance exceeding 50m but not exceeding 100m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supplying and laying un-reinforced precast concrete cable cover, classHV, Type 1, flat, size 300mmx l80mm x 40mm complete all as specified and dierected by Engr In Charge.

Supply and laying brick covering as mechanical protection to underground cable using old size sub class 'B' bricks, laid flat size 230mm x 115mm x 75 mm with width of brick perpendicular to length of cable, all as specified and as directed.

Sand cushioning to underground cables using new dry river sand laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete, punned to 18cm, complete all as specified and directed Note : Punned thickness of 18cms shall be measured for payment.

Cable jointing kit for 11 KV (earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 95 Sqmm complete all as specified and as directed.

Cable jointing kit for 11 KV (earthed) grade cable for indoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 50 to 95 Sqmm complete all as specified and as directed.

Cable jointing kit for 11 KV (earthed) grade cable for straight through joint heat shrink type complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 50-95sqmm complete all as specified and as directed.

Switch Air break, gang operated (GOD) with 12 Nos insulators, Outdoor type, mechanically operated, suitable for horizontal or vertical mounting rotating type, provided with locking arrangements consisting of MS channel, operating rod 25 mm dia GI pipe medium grade for operating from 1.2 metre above Ground Level with locking arrangement complete confirming to IS-1318 of 1972 rated voltage 11 KV and for current rating 200 Amps complete, all as specified and directed.

Steel Tubular swaged poles type 410 SP-55 (11.0 mtr long) conforming to IS : 2713 Part-I to III 1980, complete with 6 mm thick cast iron base plate, finial taper plug, MS bolts, nuts, screws including painting 06 Nos bands / strips of 30cms each starting from the bottom of the pole (i.e. above the PCC coping) with white and red post office box colour in alternate strips and two coats epoxy based paint aluminium grade finish to the remaining external surface over one coat of primer and numbering of poles with black synthetic enamel paint in 2.5 cm height including black bitumenous paint two coats on steel surface embedded in concrete foundation all as specified and as directed.

M&L for Cross arm bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, drilling holes for bolts, in any shape or size as indicated or directed and also inclusive of two coats of aluminium paint over one coat of red oxide primer, all as specified and as directed.

Lightning arrestor expulsion type complete with all fittings, transmission class, discharge capacity 65 Kilo Amp complete with all fittings, complete all as specified and directed.

M&L for Cement concrete type B-1 1:2:4 (using 20mm graded crushed stone aggregate) as in coping of poles, complete all as specified and directed.

M&L for Cement concrete type C-2 1:3:6 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete, complete all as specified and directed.

M&L for Cement concrete type D-2 1:4:8 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete, complete all as specified and directed.

S&F GI water tubing light grade, 80 mm bore laid in trenches or under ground/floor or road of fixed with pole for protection of cable including GI clamps with bolts nuts and washers complete all as specified and directed.

M&L for earthing complete with Galvanised steel earth plate electrode 600 mm x 600 mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.50 mtr below ground level connected to GI Strip of size 25 x 4mm as earth lead by means of bolts, nuts and washers of GI up to test point, GI tubing 40 mm bore light grade protection pipe, GI watering pipe 20mm bore medium grade with funnel and wire mesh, alternate layer of charcoal and salt, 40mm thick including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on Electric Plate No. 03 of SSR-2009 Part-I, complete all as directed.

M&L for earthing complete with Galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below normal GL) with top edge of the earth plate not less than 1.5 metres below normal ground level, connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts & washers of GI or steel incl excavation, PCC (1:3:6) type C-1 chamber with RCC cover (1:2:4) type B-0, 40 mm thick reinforced with 6 mm dia bar, 3 Nos. both way, 15 mm dia light grade GI protection pipe, funnel with wire mesh,watering pipe of size 20 mm dia medium grade, lugs, main earthing lead upto 7.5 mtr including. charcoal dust, salt etc. all as shown in electrical plate No. 3 of SSR Part-I, 2009 specification.

Danger notice plate, for HT, of size 25cm x 20cm x 1.5mm thick mild steel sheet, vitreous enamelled, white with letters, figures and conventional Skull & Bones in signal red colour and fixed with MS clamps, bolts and nuts of appropriate size, all as specified and as directed.

Anti-climbing device; spikes type fabricated out of M.S. bars (round, square and flat) including nuts, bolts, washers and welding in two halves made to shape to suit the cross section of the pole complete all as specified and directed.

Cable Route Indicators 4" x 4" round / square welded or bolted with angle iron stand 40 x 40 x 6mm MS angle 60cm long, marked HT / LT cables including embedding in PCC 1:2:4 size 30cm x 30cm x 30cm over cable, to be fixed on each turning, at joint across road crossing and distance as per site requirement, complete all as specified and directed by Engr In Charge.

M & L for road cutting for laying of HT cable under the existing road, and making the good disturbed surface with PCC 1:2:4 complete all as specified and directed by Engr In Charge.

Supplying laying jointing and testing XLPE insulated, PVC bedded, galvanised steel strips armoured heavy duty electric power cable with stranded aluminium conductor suitable for rated voltage of 1100 Volt grade, 3.5 Core x 185 Sqmm conforming to IS 7098 Part-I) 1988 with upto date amendments and laid in trenches / ducts / pipe or on poles including taking down complete, all as specified and directed.

Supplying laying jointing and testing XLPE insulated, PVC bedded, galvanised steel strips armoured heavy duty electric power cable with stranded aluminium conductor suitable for rated voltage of 1100 Volt grade, 3.5 Core x 120 Sqmm conforming to IS 7098 Part-I) 1988 with upto date amendments and laid in trenches / ducts / pipe or on poles, including taking down complete, all as specified and directed.

Supplying laying jointing and testing XLPE insulated, PVC bedded, galvanised steel strips armoured heavy duty electric power cable with stranded aluminium conductor suitable for rated voltage of 1100 Volt grade, 3.5 Core x 70 Sqmm conforming to IS 7098 Part-I) 1988 with upto date amendments and laid in trenches / ducts / pipe or on poles, including taking down complete, all as specified and directed.

Supplying laying jointing and testing XLPE insulated, PVC bedded, galvanised steel strips armoured heavy duty electric power cable with stranded aluminium conductor suitable for rated voltage of 1100 Volt grade, 2 Core x 16 Sqmm conforming to IS 7098 Part-I) 1988 with upto date amendments and laid in trenches / ducts / pipe or on poles, including taking down complete, all as specified and directed.

Supplying laying jointing and testing XLPE insulated, PVC bedded, galvanised steel strips armoured heavy duty electric power cable with stranded aluminium conductor suitable for rated voltage of 1100 Volt grade, 2 Core x 25 Sqmm conforming to IS 7098 Part-I) 1988 with upto date amendments and laid in trenches / ducts / pipe or on poles, including taking down complete, all as specified and directed.

Supply, installation, testing and commissioning of LT Panel cubical type 440 Volts 3 phase 4 wire outdoor type front operated any CPRI approved with adequate Air Ventilation at both sides & back & fabricated out 3.15 thick CRCA sheet with double door shutter with locking arrangement with water proof dust & vermin proof, pre fabricated hinges for rear & front door with locking arrangement complete with inter connection with copper wire / strip, tapping bonding to earth & all frames inner & outer door shall be coated by polyester powder paint of shade RAL 7032 Siemens grey stand of distribution board shall be coated by primer & black Bituminous paint, cable trays, cable lugs, cable Glands of any size with suitable to accommodate and including following mentioned fittings & fixture with suitable nut, bolt, washer etc.

CPRI approved including provision for taking out cable duly marked riveted letter at appropriate size for each feeder cable & reconnection with duly insulated cable terminals with heat shrinkable sleeve with 1.1 KV grade Danger notice board etc. (i) Bus bar chamber consisting four Nos Aluminium busbar of capacity Suitable size duly insulated with heat shrinkable sleeve 1.1 ka grade with RYBN mounted on heavy duly Epoxy insulator in separate compartment. (ii) Digital type volt meter 01 No. and Digital type Amp meter with suitable cap of CT - 01 No. (iii) LED indicating lamp (RYB) for incoming and indicating lamp (RYB) for each out going (iv) Panel board internal wiring with suitable PVC insulated multistranded copper conductor cable flexible cable.

Incoming (i) MCCB, Four Pole, 415 Volt, 200 Amps capacity with 36 KA with adjustable thermal magnetic trip unit/release with Ics= 100% Icu quantity 01 No. Outgoing (i) MCCB, Four Pole, 415 Volt, 100 Amps capacity with 16 KA with adjustable thermal magnetic trip unit/release Ics= 100% Icu= 4 Nos. (ii) MCB SPN 40 A - 02 Nos

Supply, installation, testing and commissioning in replacement of LT Panel, Cubical type, 440 Volts 3 phase 4 wire outdoor type front operated any CPRI approved with adequate Air Ventilation at both sides & back & fabricated out 3.15 thick CRCA sheet with double door shutter with locking arrangement with water proof dust & vermin proof, pre fabricated hinges for rear & front door with locking arrangement complete with inter connection with copper wire / strip, tapping bonding to earth & all frames inner & outer door shall be coated by polyester powder paint of shade RAL 7032 Siemens grey stand of distribution board shall be coated by primer & black Bituminous paint, cable trays, cable lugs, cable Glands of any size with suitable to accommodate and including following mentioned fittings & fixture with suitable nut, bolt, washer etc.

CPRI approved including provision for taking out cable duly marked riveted letter at appropriate size for each feeder cable & reconnection with duly insulated cable terminals with heat shrinkable sleeve with 1.1 KV grade Danger notice board etc. (i) Bus bar chamber consisting four Nos Aluminium busbar of capacity Suitable size duly insulated with heat shrinkable sleeve 1.1 ka grade with RYBN mounted on heavy duly Epoxy insulator in separate compartment. (ii) Digital type volt meter 01 No. and Digital type Amp meter with suitable cap of CT - 01 No. (iii) LED indicating lamp (RYB) for incoming and indicating lamp (RYB) for each out going (iv) Panel board internal wiring with suitable PVC insulated multistranded copper conductor cable flexible cable

Incoming (i) MCCB, Four Pole, 415 Volt, 250 Amps capacity with 36 KA with adjustable thermal magnetic trip unit/release with Ics= 100% Icu quantity 01 No. Outgoing (i) MCCB, Four Pole, 415 Volt, 200 Amps capacity with 25 KA with adjustable thermal magnetic trip unit/release Ics= 100% Icu = 2 Nos. (ii) MCCB, Four Pole, 415 Volt, 125 Amps capacity with 25 KA with adjustable thermal magnetic trip unit/release Ics= 100% Icu= 3 Nos. (iii) MCB SPN 40 Amps - 02 Nos (iv) Front operated Four Pole 200 Amps On load Change Over Switch - 01 No

Supply, installation, connecting electrically & commissioning LT Feeder Box, outdoor type of size 0.90m x 0.60m x 0.40m size, factory fabricated, made out of MS sheet of thickness 3.15mm front and back door openable with locking arrangement mounted on angle iron legs made out of angle iron of size 40 x 40 x 6mm, 1.5 mtr long, 1.0 mtr above ground level and 0.50 mtr embedded in PCC blocks of size 0.30 x 0.30 x 0.50 mtr -04 Nos duly painted with two coats of synthetic enamel paint over a coat of red oxide complete with 300 Amps rated aluminium bus bar suitable for 3 phase 4 wire supply dully drilled holes for cable connection mounted on epoxy based post insulators and one No. MCCB 200 Amp, 25 KA, 4 Pole 415 V , all as specified and directed.

M & L OCTAGONAL pole 07 mtr height, type BOP-7030 ,Top dia 70 mm,bottom dia 130mm,sheet thickness 03mm and base plate dimention 200x200x12 mm, bolt dia 4x20 dia, Pitch circle dia 200mm, Bolt length 600 mm, Procted bolt length 100 mm ,screw including all fixing arrangement as per requirement at site all as specified and directed by Engr-in-charge.

S & F foundation bolt of size 4x20 dia 200x600x100 mm for OCTAGONAL pole including fixing arrangement complete all as specified and directed.

S & F single arms bracket 01 mtr long for pole having 70 mm A/F for OCTAGONAL pole including fixing arrangement complete all as specified and directed.

S & F Double arms bracket 01 mtr long for pole having 70 mm A/F for OCTAGONAL pole including fixing arrangement complete all as specified and directed.

S & F Sleek junction box with one 06Amps SP MCB and 16 sqmm stud type connector for single arms bracket for OCTAGONAL pole including fixing arrangementcomplete all as specified and directed.

S & F Sleek junction box with one 06Amps SP MCB and 16 sqmm stud type connector for double arms bracket for OCTAGONAL pole including fixing arrangement all as specified and directed.

Danger notice plate, for LT, of size 20cm x 15cm x 1.5mm thick mild steel sheet, vitreous enamelled, white with letters, figures and conventional Skull & Bones in signal red colour and fixed with MS clamps, bolts and nuts of appropriate size, complete all as specified and as directed.

Supply & fixing Pressure die-cast aluminium IP 65 cool white road way luminaire with high power LED as Light source with 72 Watt high power LED with inbuilt surge protection upto 5 kv including with suitable GI Pipe Bracket , double clamps complete with nut bolts with pole and 2.5 sqmm 3 core copper wire multistrand for connection from DB to Light complete all as specified and as directed.

S&F GI pipe light grade, 40 mm bore laid in trenches or under ground/floor or road of fixed with pole for protection of cable including GI clamps with bolts nuts and washers , including taking down complete all as specified and directed.

S&F GI pipe light grade, 50 mm bore laid in trenches or under ground/floor or road of fixed with pole for protection of cable including GI clamps with bolts nuts and washers, , including taking down complete all as specified and directed.

Stay assembly complete with accessories as shown in electrical plate No. 1 (loop type insulator, stay clamps, excavation and concrete measured separately) complete all as specified & directed.

M&L for galvanised stay strand, 7/4mm complete all as specified & directed.

M&L for dismantling concrete poles/ struts, any size complete all as specified & directed.

M&L for dismantling steel poles/ struts, any size complete all as specified & directed.

M&L for dismantling cross-arms of M.S. channel or angle sections etc. complete and setting aside for re-use with in 50m complete all as specified & directed.

M&L for dismantling insulators any type, any size complete all as specified & directed.

M & L for dismantling stay assembly complete. (demolition of concrete, etc. and excavation measured separately complete all as specified & directed.

M & L for Loop type insulator vitreous porcelain, white, brown or green:,with overall dimension 90mmx140mm, clearance of hole 25.5 mm complete all as specified & directed.

M/S SHRI RAM BUILDERS

kailu construction co

Ashoka Engineers

M/S SATYA CONSTRUCTIONS

UNITED ENGINEERING CORPORATION

JCC ENGINEERS PRIVATE LIMITED

Auto India

Sanjay Constructions

Bidder Name

kailu construction co

Auto India

UNITED ENGINEERING CORPORATION

Ashoka Engineers

M/S SATYA CONSTRUCTIONS

M/S SINGH AND ASSOCIATES

Sanjay Constructions

JCC ENGINEERS PRIVATE LIMITED

M/S SHRI RAM BUILDERS