82622/E8 Provn of Adequate gender specific Toilet for AGV and other Women employees (Civilians) at 5 BRD

Surface excavation n.exc 30 cm deep and getting out in hard / dense soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeded 1.5m in depth; for foundation etc. or for shafts, wells, cess pits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in hard/dense complete all as specified and directed.

Returning, filling in of soft/loose soil including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing surplus excavated earth (soil) to a distance n.exc 50m & Depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L Plain cement concrete (1:4:8) type B-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M&L for RCC M-25 (Design mix) (using 20mm graded stone aggregate) as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, etc and mass concrete complete all as specified and directed.

Formwork to flat sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L for RCC M-25 (Design mix) using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts, etc and mass concrete complete all as specified and directed.

Formwork to Square, rectangular or polygonal rough surface of concrete of sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for RCC M-25 (Design mix) using 20mm graded stone aggregate as in beams, cantilevers, bressumers, lintels over 1.5m span etc complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for RCC M-25 (Design mix) using 20mm graded stone aggregate as in Chajja complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed

M&L for RCC M-25 (Design mix) using 20mm graded stone aggregate as in slabs supported on walls etc complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No.16 above but for 5mm dia and over upto and including 10mm dia in stirrups, spacer and binders complete all as specified and directed

M&L for Brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on brick or concrete surface, finishing even and smooth without using extra cement but using water proofing compound complete all as specified and directed. Note:- The water proofing compound shall be measured and paid separately. The dosage shall be as per manufacturers instruction.

M&L rendering 15mm thick plaster in CM 1:6 on fair faces of brick or concrete surfaces (internal walls) finished fair and even without using extra cement complete all as specified and as directed.

M&L for rendering 5mm thick in CM 1:3 on concrete surface of ceiling finishing even and smooth without using extra cement complete all as specified and directed.

M&L for Moorum / Red bajri filling in floors or pavings, laid in layers n.exc15 cm thick spread levelled and rammed incl watering etc all as specified & directed.

M&L Hard core of gauge n.exc 63 mm, deposited, spread, levelled in layers not exc 15 cm thick, watered and well rammed to a true surface complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in floors finished even surface complete all as specified and directed.

M&L for cement concrete 1:3:6 type C2, 75mm thick with using extra cement as in plinth protection complete all as specified and directed.

M&L for 100mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tiles exceeding 0.06 sqm but n.exc 0.11sqm in floor etc, over and incl 15 mm thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces complete all as specified and directed.

M&L for glazed ceramic coloured tiles 450x350x7mm thick on vertical surfaces such as skirting dados set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4). Complete all as specified & directed.

M&L for Granite 20 mm thick (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and directed.

M&L for Granite 20mm thick (table rubbed and polished) in steps, Jamps, Pillars, Window cills, platforms and like CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble shade of Granite over screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) all as specified and as directed.

M&L three coats of white wash on new plastered ceiling surface including preparation of surfaces complete all as specified and directed.

M&L preparing surface plastered or unplastered on wall with two coats of Cement base paint over a coat of alkali resistant primer paint with complete all as specified and directed.

M&L for three coat of white washing in internal wall including preparation of surfaces complete all specified and as directed.

M&L rendering 10 mm thick in CM 1:3, mixed with water proofing compound on concrete surfaces of roof , surface finished even and smooth. Note:- The water proofing compound shall be measured and paid separately. The dosage shall be as per manufacturers instruction.

Providing and laying / fixing TPO (Thermoplastic Polyolefin) water proofing membrane of non-flammable waterproofing to roof to make a 1.5mm thick loose laid membrane using Fosroc Proofex ORG membrane or equivalent make all as per manufacturer's instruction. Note for material to be incorporated:- (a) Layers are overlapped to achieve a minimum weld of 110mm. (b) Hot air welding can be either hand applied or by means of automatic machines. (c) The roll's either end shall be overlapped with 110mmand are in stagered positions. (d) The membrane shall be laid over the layer of non-woven geotextile fibre (Minimum 200GSM). (e) The separation layer shall be provided to prevent the mechanical abrasion and cushioning between the Fosroc Proofex ORG membrane and the concrete substrate. (f) The termination of Fosroc Proofex ORG by aluminium strop anchoring and sealant filling shall be as per manufacturer's specification. (g) Water proofing membrane shall be all weather proof and UV resistance.

Item No.36 Contd..../- (h) The TPO membrane shall have the following properties:- (i) Thickness : 1.5mm (ii) Tensile Strength : >9 N/mm² (iii) Elongation at break : > 950% (ASTM D 412) (iv) Puncture resistance > 1000mm : Pass (EN 12691) (v) Water impermeability : Pass (EN 1298 & EN 12691) (vi) Tear Resistance : 470 N (EN 12310 - 1) (vii) Root Resistance : Pass Test - No Penetration (viii) Lap joint strength : Pass Test (EN 12317 & UEATc) (h) Preparation of Surfaces: Surfaces should be free from cavities and projecting nibs. All surfaces shall be dry and free from frost, surface laitance and contamination. Note for Water proofing treatment:- (i) The work shall be carried out through authorized and qualified applicators of the manufacturer's only. MOU with applicators shall be submitted before commencement of work. (ii) A performance guarantee certificate for a period of 10 years from the certified date of completion of work shall be submitted by the contractor to the GE . (iii) The unit rate quoted shall be inclusive of material, labours, tools and plants including scaffolding required for working upto 3.5m height from natural ground level (iv) Necessary safety arrangement like safety belts, ropes, helmets, netting etc which are required for safety of working labour at height exc 3m to be provided by the contractor and the rate for this provision is deemed to be inclusive in the quoted rate

Supply only water proofing compound of approved make.

M&L for Brick work with subclass 'B' bricks straight or curved on plan to any radius half brick thick wall built in CM 1:4 complete all as specified and directed.

M&L for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

M&L Flush shutters,30mm thick, solid core construction, with particle board core and ply wood face panels, commercial type on both sides, complete all as specified and directed.

M&L for Preparation of new wood or wood based surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

S&F Powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) and aluminium grill complete all as specified and directed by Eng-in-charge.

S&F Powder coated anodised aluminium frame for door section/ window section/ ventilator section for side hung type shutter /sliding type shutter/fixed type shutter in two or more tracks, including automatic locking handle , rollers and roller plate & fitting arrangement complete all as all as specified and directed by Engineer-in-charge. Note:- Glass pane, hydraulic door closer, plush plate, floor hinges etc shall be measured and paid separately.

M&L for provision of new 4mm plain sheet glass ordinary quality and glazed with oil putty area of glass exc 0.5 sqm each pane complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tub complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with het moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plan colour PVC sheets for top rail, lock rail & bottom rail on either side & as flap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement supplying & fixing in the frame at site as per specification & drawing.

S&F aluminium anodised barrel tower bolt 200 mm complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt 300 mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete.

S&F MS 100 mm size butt hinges medium wt. of cold rolled complete and all as specified and directed

Aluminium handles, cast type anodised150mm size complete all as specified and directed

S&F for Pillar taps fancy type 15mm bore CP with capstan head screwed down high pressure screwed for iron pipe complete as directed by Engr-in-charge.

S&F for Bib Cock CP fancy type with wall flange screwed down screwed for iron pipe15mm bore in repairs complete as directed by Engr-in-charge.

S&F in repairs two way Bib cock, cast copper alloy, screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipes or for unions and fixed. 15 mm size complete all as specified and directed. Make : CERA Model No: F3002212 or equivalent in other manufacturers from the list.

S&F for Health faucet (ABS Body) mild steel chromium plated finish suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

M&L PVC connection 15 mm size with PTMT nuts of length 450 mm including taking existing one complete as directed by Engr-in-charge.

S&F 75 mm dia outlet PVC (SWR) floor trap plain with steel grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) pipes 75mm dia single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed

S&F PVC (SWR) pipes 110mm dia single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed

S&F 75mm dia PVC (SWR) bends any radius complete all as specified and as directed

S&F 110mm dia PVC (SWR) bends any radius complete all as specified and as directed

S&F 110mm dia PVC (SWR) vent cowl complete all as specified and as directed

S&F 75mm dia PVC (SWR) junction single, (single T), equal or unequal complete all as specified and as directed

S&F 110mm dia PVC (SWR) junction single, (single T), equal or unequal complete all as specified and as directed

S&F Grating doom 125 mm dia with waste hole of PTMT Minimum weight 40 gms complete all as specified and directed.

S&F Stop valves cast copper alloy, screwed down, high pressure with crutch or butterfly handle chromium plated fancy type screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe complete all as specified and directed.

S&F for Toilet paper holder white of vitreous china box type fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S&F 25 mm bore dia of pipe Ball brass valves. high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule i complete all as manufactures and all as specified and directed by Engineer- In - charge

S&F Vitreous china wash down water closet pan pedestal pattern of Size 640 x 355 x 695 mm with S-TRAP and seat cover including PVC flushing cistern 10 Ltr Capacity, all accessories and complete all as specified and as directed. Make:- Cat part No. C899E(S-110) of Parry ware or equivalent model of other manufacturers from the list.

S&F Vitreous Bowl wash basin, white, flat back, size 460 x 315 x 135 mm (Table top) excluding taps, waste, chain and plug and porcelain stopper brackets complete all as specified and as directed. Make:- Cat Part S No. C895V of parry ware or equivalent model of other manufacturers from the list.

M&L 32 mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as manufactures and all as specified and directed by Engineer- In - charge

S&F soap dish vitreous china white approximate size 100 x 160x90 mm brass screws complete all as specified and directed

M&L brass chromium plated tubular towel rail 20mm dia D type 600 mm long between flanges fixed Complete all as specified and directed.

S&F 15mm bore Brass CP wall mixer for mixing hot & cold water screwed down, for iron pipe or for brass ferrule complete all as specified and directed.

S&F shower rose 125 mm brass chromium plated with swivel joints complete and all as specified and directed.

S&F of 3- layer PP-R Polypropylene random copolymer) concealed Outer diameter of pipes in 16 mm dia SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water apply all PP-R plain & brass threaded polypropylene random fittings laid in floors, wall and ceiling etc complete all as specified and directed.

S&F of 3- layer PP-R Polypropylene random copolymer) concealed Outer diameter of pipes in 20 mm dia SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water apply all PP-R plain & brass threaded polypropylene random fittings laid in floors, wall and ceiling etc complete all as specified and directed.

S&F of 3- layer PP-R Polypropylene random copolymer) concealed Outer diameter of pipes in 25 mm dia SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water apply all PP-R plain & brass threaded polypropylene random fittings laid in floors, wall and ceiling etc complete all as specified and directed.

S&F Brass chromium plated bottle traps 32mm bore dia for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed

M&L on site LLDPE septic tank for 20 users, conventional type, designed by to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft , connection etc, complete all as specified and directed.

Excavating over areas, depth n.exc 1.5m and getting out in hard/dense soil complete all as specified and directed.

Excavating over areas, depth exc 1.5m deep and getting out in hard/dense soil complete all as specified and directed.

M&L for PCC (1:3:6) type C2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

M&L for brick work with sub class B bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L for Brickwork with fly ash bricks in one brick thick honey-comb walling, built in cement mortar 1:4 complete all as specified and directed.

M&L for loose filling of broken bricks of gauge 80 to 150 mm in soakage pits, soakage well complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on brick or concrete surface, finishing even and smooth without using extra cement complete all as specified and directed.

M&L PCC 1:2:4 types B-1 using 20 mm graded crushed stone aggregate as in coping etc complete all as specified.

M&L for cement concrete in 1:3:6 type C2, 50mm thick using40 mm graded stone aggregate as in surface channel and drain, complete all as specified and directed.

Extra for fixing fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

M&L for Providing precast cement concrete (PCC 1:3:6), type C-1 using 20 mm graded stone aggregate in landing, cover slabs (for manholes etc) challah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar CM 1:4 complete all as specified and directed.

Supply and laying double wall corrugated (DWC) pipe HDPE pipe of outer dia 175mm and inner dia 147mm of approved make ISI marked polythene with smooth internal wall & profiles external surfaces for non pressure for sewage complete all as specified.

M&L for concrete bed to drain pipes of 150mm dia in PCC 1:3:6 type C2 using 40mm graded crushed stone aggregate including packing under haunching against the sides of pipe after they are laid and tested for complete all as specified and directed.

M&L for 100mm thick Plain Cement concrete 1:4:8 type D2 using 40 mm graded aggregate as in sub base etc complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60 mm thickness M-35 Grade with Grey cement and with no pigment complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60 mm thickness M-35 Grade with Grey cement and with pigment complete all as specified and directed.

M&L for sand cushioning including spreading and levelling in layers and rolled consolidated to thickness of 25mm (minimum) for receiving precast PCC interlocking paver blocks complete all as specified and directed.

M&L Precast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar (kerb stone) as in PCC 1:3:6 type C1 using 20 mm graded stone aggregate and set in CM 1:6 incl formwork complete all as specified and as directed.

M&L for Point wiring with 1.5 sq mm (nominal area), two single core PVC insulated unsheathed, 1100 volts grade, multistranded copper conductor in and including PVC casing capping of adequate size with all fittings and accessories including PVC board with top cover for housing / mounting brackets switches, sockets etc., including PVC insulated unsheathed single core multi stranded copper conductor cable of size 1.5 sqmm green inn colour as earth continuity conductor connected to common earth dolly for one light/fan point controlled by one way switch complete all as specified and directed.

S&F Switch modular single pole one way, one module 6 Amp 240 volts complete all as specified and directed

S&F Ceiling rose surface Bakelite 65 x 50 mm two to three terminals complete all as specified and directed.

S&F Lamp holder, insulated body, with back plate for angular batten fittings with one PVC block of size 75mmX75mm for mounting the fitting including with one LED 1 X 15 Watt complete all as specified and directed.

S&F Energy saving new generation 10 watts with lumen efficiency not less than 100lumens/watt, LED bulk head fitting IP 65 luminaire with opal diffuser pre wired and necessary mounting arrangements ,permissible limit of CRI range, with recommended burning hours,4000K/6500K etc provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed..

S&F sheet metal enclosures MCB DB SPN 4 way with 200 Amps rated bus bar 240 volts 1-ph, 50Hz double door with magnetic locking system complete all as specified and directed.

Supply and fix MCB SPN, 240 volt, 6 to 32 Amps complete all as specified and directed.

Supply and fix MCB Single Pole 240 volt, 6 to 32 Amps complete all as specified and directed.

M&L for Sand cushioning of cables provided with a layer of sand 8 cm deep before laying the cable and 15 cm depth after punning down and stretching the cable.

Supply and laying LT UG cable XLPE insulated armoured and PVC sheathed LT 1100 volts grade with aluminium conductor 10 Sqmm 2 core laying in trenches or on wall, roof etc by securing clamp all as specified and directed by Engr-in-Charge.

S&F LED light fitting mirror type with high out put diffuser 2 feet 9/10 Watt LED light fitting batten type with Luminaries & integrated driver batten with lumen out not less than 110 lumens/watts & housing extruded polycarbonate housing square shaped diffuse, permissible limit of CRI range, with recommended burning hours,4000K/6500K etc suitable for mounting on wall/surface/ceiling complete all as specified and as directed.

S&F LED light fitting 18 watts (T-8) 4 feet, with output of not less than 110 lumens/watts , box type made with epoxy white powder coated CRCA sheet steel (decorative) light fitting having G13 bipin holders compatible for mounting on wall/ceiling/surface, permissible limit of CRI range, with recommended burning hours ,4000K/6500K etc , 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, including provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with integrated driver of LED tube rod 4' x 18 watts complete all as specified and as directed.

S&F Exhaust fan, steel body AC single phase 230V of size 300 mm sweep with blades and frame and louvers complete all as specified and as directed.

Cutting existing any pipe of 40 or 50 mm for alterations or additions including screwing for inserting tee , reducer etc for taking branch connection including new fittings and fixtures complete all as specified and as directed .

Supply and lay 3 Layer PP-R Polypropylene random copolymer 25 mm outer diameter of pipes concealed SDR 7.4 (PN 16 @ 20°C) UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply including all PP-R plain & brass threaded polypropylene random fittings in trenches complete all as specified and as directed.

Supply and lay 3 Layer PP-R Polypropylene random copolymer 20 mm outer diameter of pipes concealed SDR 7.4 (PN 16 @ 20°C) UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply including all PP-R plain & brass threaded polypropylene random fittings in trenches complete all as specified and as directed.

S&F 25 mm outer dia PP-R Gate Valves (Brass insert) with iron wheel head screwed both ends for iron pipes and including taking out unserviceable Gate valves complete all as specified and directed.

S&F 20 mm outer dia PP-R Gate Valves (Brass insert) with iron wheel head screwed both ends for iron pipes and including taking out unserviceable Gate valves complete all as specified and directed.

S&F Rotational moulded polyethylene PVC water storage tank 3 layer 500 litres capacity conforming to IS, hoisting and fixing in position, connection up pipes incl inlet and outlet connections etc, tank cover with locking arrangement as per SSR Part I complete all as specified and directed