Construction of road in 7.00 metre width on both side patries of Faizabad Canal From Chainage 53.840 (Raebareli Road) to Chainage 56.260 ( Prayagraj Ayodhya Road) in District Ayodhya.

Amount

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness.

Loosening, levelling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Table 300-2 for embankment construction.

Excavation for roadwork in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m

Dismantling of flexible pavements and disposal of dismantled materials up to a lead of 1000 metres, stacking serviceable and unserviceable materials separately

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of table 300-2.(compaction only)

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2.

Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2

Construction of Granular Sub-Base by providing Close graded material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with Vibratory roller to achieve the desired density, complete as per technical clause 401

Providing, laying, spreading and compacting graded stone aggregate in layers Wet Mix Macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

Providing and applying primer coat with SS-1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means.

Providing and laying dense graded bituminous macadam Grade-I with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects.

Providing and applying tack coat with bitumen (VG-10) using Bitumen pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom.

Providing and laying bituminous concrete Grading-II with hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder VG-30 @ 5.4% of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 509 complete in all respects

Earth work in excavation in trench for foundation in ordinary soil i/c lift upto 1.50 mtr. & lead upto 50.00 mtr and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed bu the E/I within a distance of 50 m.

Plain cement concrete in open foundation complete as per drawing and technical specifications PCC Grade M15 With Batching Plant, Transit Mixer and Manual placing.

Reinforced cement concrete in open foundation complete as per drawing and technical specifications RCC Grade M25 With Batching Plant, Transit Mixer and Manual placing.

Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications.

Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.

Providing and laying Cement concrete wearing coat M-30 grade excluding reinforcement complete as per drawing and Technical Specifications

Brick Masonry Work in Cement Mortar 1:3 in Foundation complete excluding Pointing and Plastering, as per Drawing and Technical Specifications.

Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical

Struck Pointing on brick work with cement mortar 1:3 (1Cement :3 sand)

Back filling behind abutment, wing wall and retaining wall complete as per drawing and technical specification clause 1204.3.8 of MORD specification.

Providing and laying 350MM NP-3 Hume pipe i/c all taxes and cartage complete.

Providing and Laying 80mm thick rubber moulded reflective Zig Zag Shape inter locking tiles of precost compressive strength in Gray and Red Colour over prepared base of GSB using local sand for levelling and joing filling i/c all cost of labour T&P etc. required for proper completion of work.

Providing and laying of hot applied thermoplastic compound 2.50 mm thick in 100mm widh including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.50 mm is exclusive of surface applied glass beads as per IRC:35. The finished Surface to be level, uniform and free from streaks and holes.

Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 4 mm thick supported on a mild steel angle iron post 35 mm x 35 mm x 3 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing.

Supply fixing & erection of built up cantilever structure 6.00M Span comprising of one vertical posts of 6.00 M high made up of 300 mm N.B. havi Class M.S. Pipe as vertical member welded with 10mm thick M.S. Plate at top & 12mm plate at bottom. the horizontal truss shall comprise of 50mm dia havy class M.S. pipe and 40mm dia heavy M.S. pipe as bracing & 10 mm M.S. plate bottom for fixing to vertical post as per structure desing & drawing with one of sttel primer and two coats of synthetic enamel plant. the work i/c construction of RCC foundation of size 90Mx90M of required depth as per site condition for built up structure i/c earth work in excavation 100 mm thick lean concrete in 1:4:8 cement sand and 40mm gauge stone ballast. RCC withand 1:2:4 cement coarse sand and 20mm stone grit i/c supply and fixing of 25mm dia foundation bolts 600 mm long as per provision of structure design i/c cost of renforcement & shuttering. as per direction of Engineer in charge.

Supply and fixing rectro reflective sign board made up with 4mm thick aluminium composite panel (ACP) face full coverd with high intesity prismatic retro reflective sheeting of approved specification as per M.O.R.T & H having approved message fully processed on by pressure sensitve equipment banc of ACP with frame of 35x35x4mm angle iron all round and cross with proper clamping arrangement to be fixed in structure. the back of the ACP sheet shall be enamel coated. as per direction of Engineer in charge.

HAZARD MARKER Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 4 mm thick supported on a mild steel angle iron post 35 mm x 35 mm x 3 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing.

VILLAGE/HOSPITAL/SCHOOL SIGN BOARD Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 4 mm thick supported on a mild steel angle iron post 35 mm x 35 mm x 3 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing.

REPEATED BAR Providing and laying of hot applied thermoplastic compound 5mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.

Supply and fixing of reflective raise the pavement marker with its body surface made of tough ASA(acrylic styrene Acrylonitrile) or HIPS ( Hi- impact Polystyrene)or acrylonitrile butadiene styrene (ABS). The marker shall support a load of thousand three 35 KG tested in accordance with a STMD4280 and its reflective panels shall consist of number of lenses containing single or dual is a Matic cubes of providing total internal reflection of the light entering the lens face retro reflecting surface LB 35 plus or -5° to base and area of each retro reflecting surface shall not be less than 13 cm² Road states shall be legible with name trade mark or other means of identification of the manufacturer dimensions of road studs so it should not be less than 100mm x 100mm x 10mm-RPM with shank as per ASTM.

Type - A, "W" : Metal Beam Crash Barrier (Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811)

The routine maintenance of above road work including earthen shoulder and bituminous pavement etc to the required standards and in the manner as defined in CB condition and keep the entire road surface and structure in Defect free condition during the entire maintenance period which begins from the actual completion date and ends after five years. (Including cost of material, T&P, labour but excluding GST) for 1st year maintenance cost @ 0.00%.

The routine maintenance of above road work including earthen shoulder and bituminous pavement etc to the required standards and in the manner as defined in CB condition and keep the entire road surface and structure in Defect free condition during the entire maintenance period which begins from the actual completion date and ends after five years. (Including cost of material, T&P, labour but excluding GST) for 2nd year maintenance cost @ 0.25%.

The routine maintenance of above road work including earthen shoulder and bituminous pavement etc to the required standards and in the manner as defined in CB condition and keep the entire road surface and structure in Defect free condition during the entire maintenance period which begins from the actual completion date and ends after five years. (Including cost of material, T&P, labour but excluding GST) for 3rd year maintenance cost @ 0.50%.

The routine maintenance of above road work including earthen shoulder and bituminous pavement etc to the required standards and in the manner as defined in CB condition and keep the entire road surface and structure in Defect free condition during the entire maintenance period which begins from the actual completion date and ends after five years. (Including cost of material, T&P, labour but excluding GST) for 4th year maintenance cost @ 0.75%.

The routine maintenance of above road work including earthen shoulder and bituminous pavement etc to the required standards and in the manner as defined in CB condition and keep the entire road surface and structure in Defect free condition during the entire maintenance period which begins from the actual completion date and ends after five years. (Including cost of material, T&P, labour but excluding GST) for 5th year maintenance cost @ 1.0%.

M/S SINGH CONSTRUCTION (BID ID -5388760)

M/S SRI BHAWAN (BID ID -5388722)

M/S A.S.TRADERS (BID ID -5389958)

M/S RAJ CONSTRUCTION (BID ID -5388596)

M/S SURYANSH INFRA DEVELOPERS PVT LTD (BID ID -5389775)

M/s S.G Enterprises (BID ID -5385946)

M/s Pawan Traders (BID ID -5374502)

M/S SRI JAN CONSTRUCTION (BID ID -5387340)