SPECIAL REPAIR TO 08 X QTRS BLDG NO P 21 22 OF JCOs OR MD ACCN OF 21 PARA SF AT ROWRIAH IN JORHAT MILITARY STATION UNDER GE JORHAT

Amount

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4.0 Sqm each, complete all as directed.

Taking down shutters of any description exc 1.0 sqm and not exc. 2.0 sqm each, complete all as directed.

Taking down shutters of any description exc.1.0sqm but not exc. 2.0 sqm each and refixing in same opening, complete all as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level), complete all as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, complete all as directed.

Demolition of reinforced cement concrete of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as directed.

Materials and labour for, plain cement concrete (1:2:4) type B0 (using 12.5 mm graded crushed stone aggregate) for holdfast/ bed block, complete all as specified and directed.

Material and labour for, RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

Material and labour for, brickwork with subclass ‘B’ bricks, old size, straight or curved on plan exc. 6m mean radius built in cement mortar (1:4), complete all as specified and directed.

Material and labour for, 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed or bedding in cement mortar (1:6) after taking down old slab complete all as specified and directed.

Material and labour for, use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete, complete all as specified and directed.

Material and labour for, 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

Supply and fix for, 30mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); complete all as specified and directed.

Supply and fix for, 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and both faces is covered with decorative face veneer with lipping/ frame to match, complete all as specified and directed.

Supply and fix for, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as per specification & drawing.

Supply and fix for, factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, complete all as specification and drawing.

Supply and fix for, 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

Supply and fix for, 100mm size stainless steel butt hinges, medium weight, complete all as specified and directed.

Supply and fix for, aluminium anodised, barrel tower bolts of extruded section of size 200mm long, complete all as specified and directed.

Supply and fix for, aluminium handles, cast type, anodised 150mm size complete all as specified and directed.

Supply and fix for, stainless steel handle 125mm size complete all as specified and directed.

Supply and fix for continuous (piano) hinges, mild steel, bright finish or electrogalvanised 30mm Width of flaps (when open), complete all as specified and directed.

Supply and fix for, 125mm size hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed.

Supply and fix for, 150mm size floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed.

Supply and fix for, PVC butt hinges of size 100mm, complete all as specified and directed.

Supply and fix for, PVC barrel towel bolts of size 100mm, complete all as specified and directed.

Supply and fix for, PVC handle of size 150mm, complete all as specified and directed.

Supply and fix for, 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

Supply and fix in repair for, fancy type stainless steel curtain rod of size 25mm dia for doors/ windows etc including SS bracket and funnels/ dome, complete all as specified and directed.

Supply and fix in repairs for, brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

Supply and fix for, rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-290 Gde E-165, complete all as specified and directed.

Supply and fix for, rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410 -W (Gde- E- 250) quality- A, complete all as specified and directed.

Supply and fix for, rolled mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe 410 -W (Gde- E- 250) quality- A, complete all as specified and directed.

Supply and fix for, rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240, complete all as specified and directed.

Supply and fix for, mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Supply and fix for, pressed steel frames 105 x 60mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Supply and fix for, pressed steel frames 125 x 60mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Supply and fix for, mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5cm long and dis of bolt 5 to 10mm, complete all as specified and directed.

Supply and fix for, aluminium sliding window with powder coating (minimum thickness of powder coating 50 micron) including following components/ specifications, complete all as specified and as shown on drawing No.CESZ/2015/TD/007 Sheet No.1R/5, 3R/5, 4R/5 & 5R/5:- (i) Two leaf glazed sliding shutter and one leaf gauzed (fly proofing) sliding shutter. (ii) Opening of windows exc. 0.90 Sqm but not exc.1.5 Sqm. (iii) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (iv) All vertical/ horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) Sheet glass and stainless steel wire mesh shall be included. (vi) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, etc. (vii) Rest all as shown on drawing.

Supply and fix for, aluminium sliding window with powder coating (minimum thickness of powder coating 50 micron) including following components/ specifications, complete all as specified and as shown on drawing No.CESZ/2015/TD/007 Sheet No.1R/5, 3R/5, 4R/5 & 5R/5:- (i) Top hung gauzed (fly proofing) shutter and bottom portion fixed glazed. (ii) Opening of windows not exc. 0.90 Sqm. (iii) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (iv) All vertical/ horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) Sheet glass and stainless steel wire mesh shall be included. (vi) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, etc. (vii) Rest all as shown on drawing.

Supply and fix, anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Taking down tarfelt with cement plaster from and lowering and removing the same to a distance exc. 50m and not exc.100m including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc., and brushing neat cement slurry with 3.0Kg of cement per sqm, complete all as specified and adirected.

Material and labour for, plain cement concrete (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in roof kerbs, padding, coping including haunching, benching etc, complete all as specified and directed.

Material and labour for, rendering 10 mm (average) thick, cement plaster, in cement mortar (1:3), finished even and smooth without using extra cement mixed with and incuding water proofing compound as per manufactures instructions on roof surfaces and providing 3mm thick (minimum) APP (Atactic Polypropylene Polymer) modified prefabricated five layers, weight not less than 3.5 Kg/ Sqm water proofing membrane, black finished reinforced with non woven polyester matt (weighing not less than 160 gms/ Sqm) with applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm over a coat of bituminous primer @ 0.40 Litre/ Sqm and one coat of bitumen based UV reflective paint with aluminium paint as per manufacturer's instruction over APP membrane. The membrane shall be laid using butane torch and sealing all joints etc., complete all as specified in Para 11.44.5 of SSR Part-I and directed.

Material and labour for, 18/19 mm thick MDF board, commercial type fixed with screws to timber frame work as in lining, panelling similar location cup board shutter, shelf, kitchen cabinets, partition etc. including taking down old unserviceable, complete all as specified and directed.

Material and labour for, powder coated aluminium snap grid frame work for false ceiling, size of grid 605 x 605mm, including aluminium main / cross tee section of size 35mm x 23mm x 1.5mm (minimum) and aluminium angle 25mm x 23mm x 1.5mm thick, suitable size GI wire hanging arrangement with adjuster all as specified in clause No.10.38 in SSR Part-I and incuding 4mm thick high pressure steam cured non asbestos fibre cement reinforced multipurpose board as per IS 14862 including taking down existing false ceiling system, complete all as specified and directed.

Material and labour for, 75mm thick plain cement concrete (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in sub base floor, complete all as specified and directed.

Material and labour for, outdoor antiskid vitrified paving tiles of size 300x300x10mm thick laid in floor over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) including, complete all as specified and directed.

Material and labour for, 75mm thick plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in plinth protection laid in alternate bays, finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, 25mm thick plain cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in floor, finished even and smooth with using extra cement, complete all as specified and directed.

Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.11 Sqm but not exc.0.18 Sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:6), complete all as specified and directed.

All as per serial item No. 58.00 here-in-before but as in skirting/ dado over cement mortar (1:4) backing coat.

Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.18 Sqm but not exc.0.38 Sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:6), complete all as specified and directed.

All as per serial item No. 60.00 here-in-before but on skirting over and including 10mm thick backing coat in cement mortar (1:4).

Materials and labour for, glazed ceramic coloured tiles, 450 X 350 X 7mm thick, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat in cement mortar (1:4), complete all as specified and directed.

Taking down of existing sunken portion treatment by dismantling of old concrete and carry out the sunken treatment as per following:- (i) Supply and fix for, GI 40mm dia light grade, drainage spout pipe upto out side of outer wall (Approx 0.45m to 0.60m long). (ii) Material and labour for 50mm thick PCC (1:1.5:3) type A0 (using 12.5mm graded crushed stone aggregate) laid in slope towards drainage out spout pipe mixed with water proofing chemical as per manufacturer instruction of make FOSROC/ Sika/ Pidilite/ STP Khura, 150mm x 150mm (min) at appropriate location for free flow (of leaked if any) towards drainage spouts shall be provided internally while laying PCC. Fixing of spout shall be done with same PCC as in this item. (iii) Material and labour for, rendering 18 mm thick, cement plaster, in cement mortar (1:3) on vertical surfaces mixed with water proofing chemical of make: '301' Pidicrete URP of Dr Fixit or other techno chemically equivalent of make: Sika/Pidilite/FOSROC/STP as approved. (iv) Applying two coats of SIKA TOP seal 107 or other technochemically equivalent of make FOSROC/ Pidilite/ Dr Fixit/ STP on vertical as well as horizontal surface. (v) Drainage and water supply pipe if required, test for leakage/ sanitary pipe and shall be laid to slope and clear gap underneath the pipes shall be made available by providing suitable cement concrete blocks.

(vi) Material and labour for 150mm thick PCC (1:5:10) type E2 (using 40mm graded crushed stone aggregate) laid in slope towards drainage out spout pipe mixed. (vii) Material and labour for, 25mm thick PCC (1:2:4) type B0 (using 12.5mm graded crushed stone aggregate) as in level course. (viii) Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.11 Sqm but not exc.0.18 Sqm as in floors, set and jointed in neat cement slurry and pointed filled with epoxy chemical of make Sika/ FOSRC/ Pidilite/ Dr. Fixit/ STP mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:6). Note: (a) The sunken treatment work shall only be carried out after written approval of Engineer-in-Charge. (b) Laying of chemical required for various applications shall be as per manufacturer instructions (c) Plan area shall only be measured and paid. (d) The contractor shall give a guarantee of 10 years from date of completion of work for sunken treatment. An amount of security deposit equal to the individual security deposit calculated based on the amount of sunken treatment at contract rates min of Rs.5000.00 for the building for which treatment to be carried out shall be retained from the contractor's final bill as security deposit for the water proofing treatment which shall be released to the contractor only after expiry of guarantee period.

Material and labour for, rendering 15 mm thick, cement plaster, in cement mortar (1:6) on fair faces of brick work or concrete surfaces on walls and finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed. (Note: Water proofing compound shall be measured and paid seperately under relevant item).

Material and labour for, rendering 5 mm thick, cement plaster, in cement mortar (1:3) on fair faces of concrete surfaces on ceiling, finished even and smooth without using extra cement, complete all as specified and directed.

Supply only integral water proofing compound complete all as specified.

Material and labour for, preparation of newly plastered wall surfaces and applying three coats of white wash, complete all as specified and directed

Material and labour for, preparation of old plastered or unplastered decorated wall surfaces by washing rubbing down and applying one coat of white wash, complete all as specified and directed

Material and labour for, preparation of newly plastered surfaces and applying three coats of white wash on ceiling, complete all as specified and directed.

Material and labour for, preparation of old plastered or unplastered decorated surfaces and applying one coat of white wash on ceiling, complete all as specified and directed.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of oil emulsion distemper over a coat primer over 1mm thick wall putty, complete all as specified and directed.

Material and labour for, complete removal of existing treatment and and applying two coats of oil emulsion distemper over a coat primer over 1mm thick wall putty, complete all as specified and directed.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat primer, complete all as specified and directed.

Material and labour for, complete removal of existing treatment and applying two coats of cement base paint over a coat of primer including preparation of surfaces, complete all as specified and directed.

Material and labour for, preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Material and labour for, preparation of new or previously untreated surfaces of steel and iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Material and labour for, preparation of old painted steel and iron surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed.

Supply and fix for 15mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Supply and fix for 20mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Supply, hoisting and fixing in position of rotational moulded polyethylene water storage tanks in double layers (cylindrical vertical with closed top) of 500 litres capacity with ISI marked and all as specified in IS12701, specified in SSR Part I including 20mm dia bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed (Minimum weight 20 mm - 210 gms) for iron pipe including taking down existing water tank, complete all as specified in SSR Part I and directed.

Supply and fix in repairs for, bib tap, fancy type, cast copper alloy, chromium plated, long body with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and directed.

Supply and fix in repair for, two way bib tap with flange all as per Cat No.G5234A1/ T4634A1 of Parryware or as specified in PS including fittings screwed for iron pipe or for brass ferrule etc, complete all as specified and directed.

Supply and fix in repair for, pillar taps, fancy type, cast copper alloy, chromium plated, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

Supply and fix in repairs for, stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Supply and fix in repairs for, stop valves, with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Supply and fix in repair for, 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed.

Supply and fix in repairs for, sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

Supply and fix in repairs for, sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

Supply and fix in repairs for, vitreous china wash down water closet pan (EWC) (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with and including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

Supply and fix in repair for, vitreous china squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), connection to trap and to flushing cistern anti syphonage pipe including provision of PCC or lime concrete bedding and removal of debris, complete all as specified and directed.

Supply and fix in repairs for, vitreous china wash basin, white, flat back, size 550 x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

Supply and fix in repairs for, PVC valveless, syphonic action type, flushing cistern 10 litres capacity, low level, white, with inlet, ball valve, float and handle with flush pipe of polyethylene of low or high density or PVC 32mm dia including cutting & pinning in ends, making good the disturbed surfaces in cement mortar (1:3), complete all as specified and directed.

Supply and fix in repair for, 32mm PVC waste coupling for kitchen sink including waste pipe, complete all as specified and directed.

Supply and fix for, PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

Supply and fix in repairs for, health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

Supply and fix in repairs for, brass chromium plated shower rose 125mm size with or without swivel joints with 225mm long arms, cast copper alloy chromium plated, fixing to 15mm steel pipe or union, complete all as specified and directed.

Supply and fix in repair for, soap dish, stainless steel, fixed to plugs with chromium plated brass screws, complete all as specified and directed.

Supply and fix in repair for, stainless steel grating 100mm floor trap, complete all as specified and directed.

Supply and fix for, 75mm bore cast iron sand cast soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors including dismantling old unserviceable pipe, complete all as specified and directed.

Supply and fix for, 100mm bore cast iron sand cast soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors dismantling old unserviceable pipe, complete all as specified and directed.

Supply and fix for, 100mm bore cast iron sand cast soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to wall with MS flat iron clamps size 50 x 6mm and 16mm round bar stay of required shape and size including drilling holes and embedded in CM (1:3) dismantling old unserviceable pipe, complete all as specified and directed.

Supply and fix for, 75mm bends (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

Supply and fix for, 100mm bends (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

Supply and fix in repair for, 100mm bore cast iron vent cowl, complete all as specified and directed.

Taking down carefully unservoceable copper/ aluminium point wiring (light, fan, bell, socket or power) including all fittings such as switches, ceiling roses, regulators, sockets, switch boxes etc. complete and making good the disturbed surfaces complete all as directed.

Material and labour for, point wiring with PVC insulated unsheathed stranded FRLSH copper conductor cable of size 1.5 Sqmm in and including PVC rigid concealed conduit (heavy duty) not less than 20mm dia with all necessary fittings and necessary cutting/ chasing etc and making good the disturbed surfaces, including 1.5 Sqmm PVC insulated unsheathed stranded FRLSH copper conductor as earth lead and connected to common earth dolly for one light/ ceiling fan/ exhaust fan controlled by one, one way modular switch, complete all as specified and directed.

All as per serial item No.109.00 here-in-before for one 5 pin 6 Amps modular socket outlet on independent board.

All as per serial item No.109.00 here-in-before for one 5 Amps modular socket outlet on same board with other modular switch.

All as per serial item No.109.00 here-in-before wiring with with PVC insulated unsheathed stranded FRLSH copper conductor cable of size 2.5 Sqmm including 2.5 Sqmm PVC insulated unsheathed stranded FRLSH copper conductor as earth lead and connected to common earth dolly for one socket outlet 5 pin 15/16 Amps on independent board. (Notes for item Nos 82 to 85: Flush steel terminal box, inner plate and front plates shall be measured and paid sepertely under relevant item.)

Supply and fix for, modular metal flush box 1/2 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 3 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 6 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 8 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 2 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 3 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 6 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 8 module, complete all as specified and directed.

Supply and fix for, modular switch 1 way 6A, 1 module, complete all as specified and directed.

Supply and fix for, modular switch 1 way 16A, 1 module, complete all as specified and directed.

Supply and fix for, modular socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed.

Supply and fix for, modular socket 6A/16A - 2/3 pin combined 2 module, complete all as specified and directed.

Supply and fix for, fan step regulator, 120W - 2 module, complete all as specified and directed.

Supply and fix for, ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body, complete all as specified and directed.

Supply and fix for, sub main wiring with two runs of single core 4.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed, 1100 volts grade IS-694 marked drawn through and including rigid PVC non metallic concealed conduit medium duty (ISI marked) of required size with conduit accessories such as junction boxs, bends, tees etc. including one run of single core 4.0 Sqmm (nomonal area) PVC insulated copper conductor FRLSH, unsheathed stranded as continuous earth wire, complete all as specified and directed. Notes: All runs of copper conductor and one run of conduit shall be measured as one unit length.

Supply and fix for, sub main wiring with two runs of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed, 1100 volts grade IS-694 marked drawn through and including rigid PVC non metallic concealed conduit medium duty (ISI marked) of required size with conduit accessories such as junction boxs, bends, tees etc. including one run of single core 6.0 Sqmm (nomonal area) PVC insulated copper conductor FRLSH, unsheathed stranded as continuous earth wire, complete all as specified and directed. Notes: All runs of copper conductor and one run of conduit shall be measured as one unit length.

Material and labour for, cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed.

Supply and fix for single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, complete all as specified and directed.

Supply and fix for, sheet metal enclosure for DB's when MCBs to be used, SPN 240 volts, 8 way 200 Amps rated bus bar, metal double door type IP-43, complete all as specified and directed.

Supply and fix for, sheet metal enclosure for DB's when MCBs to be used, TPN 415 volts, 4 way 200 Amps rated bus bar, metal double door type IP-43, complete all as specified and directed.

Supply, fixing, testing and commissioning for, 6 to 32 Amp, SP 240 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply, fixing, testing and commissioning for, 40 Amp, SPN 240 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply, fixing, testing and commissioning for, 63 Amp, TPN 415 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply and fix for, LED tube light fitting 1 x 10W (+/-5%) 220 volt, AC with extruded strip in thermally conductive material and extruded housing in optically efficient material milky white with system lumen efficacy> 120 lumen per watt minimum system 2300 - 2400 and make LED of chip: Osram, Cree, Nichia, Seoul, Sumsung. Integrated electronic driver, SMD based LED constant current supply with double sided connection to avoid short circuit and surge protection greater than 2.5 KV, IP 20 protection and CRI>80, power factor> 0.95, THD less than 15%, correlated colour temperature (CCT) of 6500K, operating voltage of 140 to 270 volt, frequency of 50Hz, burning hours 50000 hours with comprises of CRCA pre-coated metal housing all as per Cat No.SLE BT 10 IL of make Surya or equivalent model of make as specified in PS, complete all as specified and directed.

Supply and fix for, LED tube light fitting 1 x 20W (+/-5%) 220 volt, AC with extruded strip in thermally conductive material and extruded housing in optically efficient material milky white with system lumen efficacy> 120 lumen per watt minimum system 2300 - 2400 and make LED of chip: Osram, Cree, Nichia, Seoul, Sumsung. Integrated electronic driver, SMD based LED constant current supply with double sided connection to avoid short circuit and surge protection greater than 2.5 KV, IP 20 protection and CRI>80, power factor> 0.95, THD less than 15%, correlated colour temperature (CCT) of 6500K, operating voltage of 140 to 270 volt, frequency of 50Hz, burning hours 50000 hours with comprises of CRCA pre-coated metal housing all as per Cat No.SLE BT20-NEO MAX-N of make Surya or equivalent model of make as specified in PS, complete all as specified and directed.

Supply and fix for, LED street light fittings of 36W made of pressure die cast aluminium housing with toughened glass cover, IP66 protection, high power LEDs with secondary lenses and system efficay should be minimum 110 lumen per watt and LM79 report should be provided from NABL accredated lab all as per Cat No.SLE UL36W IP66 LXN G1 of of make Surya or equivalent model of make as specified in PS. Driver should be BIS approved silicon filled potted driver with inbuilt 4KV surge protection and external 10 KV surge protection inside luminaire housing of trouble free service life. THD shall be <10%, power factor>0.95, CCT5700K and brand name should be embossed/ engraved on the LED fitting for traceability till life. Warranty should be 2 years and warranty certificate should be provided on OEM letterhead at the time of delivery, complete all as specified and directed.

Refixing of old serviceable light fittings or any type LED tube light fittings after rectifying necessary minor defects, complete all as directed.

Refixing of old serviceable DBs of any specification after rectifying necessary minor defects and making good the disturbed surfaces, complete all as directed.

Refixing of old serviceable MCB of any specification, complete all as directed.

Supply and fix for, street light bracket, fabricated out of 40mm bore GI tubing light grade, 1.5m length bend to the shape, mounting with MS clamp of flat iron size 40 x 5mm of suitable length 2 pairs including nut and bolts etc suitable size as directed, complete all as specified and directed.

Material and labour for, earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.50 metre below normal ground level connected to galvanised steel earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised steel and connected to main switch board or main control board as directed and including provision of concrete earth pit in PCC (1:3:6) type C1, 50mm thick pre-cast RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) cover slab (Reinforced with 8mm dia TMT bar @15cm centre to centre bothways and suitable handle made of 10mm dia), provision of funnel, wire mesh, 20mm bore galvanised steel tubing (medium grade) for watering, charcoal or coke and salt in alternate layers of 15cm (compacted thickness), 15mm bore galvanised steel tubing (light grade) for protection of earth lead connection, necessary excavation and earth work in any type of soil complete all as specified and indicated on electrical plate No.3 of SSR Part-I (2009) including testing on completion. (Note: GI earth wire and protection pipe upto 7.5metres shall be deemed to be included in the unit quoted rate).

M/S P.G CONSTRUCTION (BID ID -3451967)

A K DUTTA CHOWDHURY AND CO (BID ID -3452124)

satyabhama and co (BID ID -3453040)

KAY CEE CO. INDIA (BID ID -3452410)

M/S Praduman Kumar Sharma (BID ID -3452132)

M/S KESHAVECONSTRUCTIONS (BID ID -3452532)