Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹39.9 LAccepted-AOC | L1 | Accepted-AOC Lowest quoted rate | |
| 2 | L2₹41.8 L+₹1.9 L (4.83%)Rejected-Finance | L2 | Rejected-Finance Rejected being other than lowest | |
| 3 | L3₹41.9 L+₹2.0 L (4.98%)Rejected-Finance HARIPUSHPA APARTMENT BUILDING NO E 1 FLAT NO 01 REST CAMP ROAD DEOLALI CAMP 422 401 | DEOLALI CAMP | NASHIK | MAHARASHTRA | 422401 | L3 | Rejected-Finance Rejected being other than lowest | |
| 4 | L4₹43.4 L+₹3.5 L (8.81%)Rejected-Finance | L4 | Rejected-Finance Rejected being other than lowest | |
| 5 | L5₹43.8 L+₹3.9 L (9.79%)Rejected-Finance | L5 | Rejected-Finance Rejected being other than lowest |
Tender Value
₹50 L
EMD Value
₹1 L
Closing Date
18 Jun 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Maj Pramod Kumar Tripathi
Military Engineer Services, Garrison Engineer (South) Ahmednagar - 414002
COMPREHENSIVE B/R AND E/M REPAIRS AND PERIODICAL SERVICES TO CERTAIN BLDGS OF MES COMPLEX AT GATE NO 7 AT MIRC AND PUMP HOUSES AT ACC and S UNDER GE (S) AHMEDNAGAR
2022_MES_525084_1
8892/E8
Open Tender
Miscellaneous Works
Item Rate
270 days
Ahmednagar
Class D Cat a(i)
8 documents required · 8 mandatory
₹500
Garrison Engineer (South) Ahmednagar
₹1 L
Yes
1 Jul 2022
20 May 2022
20 Jun 2022
20 May 2022
18 Jun 2022
4 Jun 2022
20 May 2022 - 27 May 2022
60 days
Amount
Dismantling of Kota stone slab, Cudappah stone of any description in floor, laid, bedded & pointed in any mortar, & interlocking paver blocks bedded on and including sand all as specified and as directed.
Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.
Demolition of cement concrete (un-reinforced) in ground floor & paving n.exc. 15cm thick below or above ground level all as specified and as directed.
Demolition of brick/stone masonry built in cement or cement lime mortar all as specified and as directed.
Taking down cement plaster of any description on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and as directed.
Taking down shutters of any description, area exceeding 1 sq. m but not exceeding 2 sq. m each all as specified and as directed.
Taking down chowkats or frames with shutters (without taking off shutters from the frames), area not exceeding 1.5 sq. m each all as specified and as directed.
Dismantling of PGI /translucent sheets of any guage or any thickness/size all as specified and as directed.
Dismantling asbestos cement (corrugated, Semi-corrugated etc.) sheets in roof coverings including ridges all as specified and as directed. .
Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.
Dismantling of posts or struts (wood, steel or RCC) of any section embedded in concrete,brick work,masonry etc. including taking out embeded portion and making good disturbed ground complete all as specified and directed.
Dismantling old fencing wire mesh/chain link fencing, any description complete all as specified and as directed.
M&L for moorum filling in floors or paving, laid in layers n.exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.
M&L for hard core of gauge exc. 63 mm but n. exc. 100 mm, deposited spread and levelled in layers n. exc. 15cm thick, including watering and rammed etc. complete all as specified and as directed.
M&L for plain cement concrete, 1:4:8, type D2 (using 40mm graded stone aggregates) as in foundation, filling and mass concrete etc. complete all as specified and as directed.
M&L for reinforced cement concrete, 1:2:4, type B-1, using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified and as directed.
M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6, complete all as specified and as directed.
M&L for walling of random rubble masonry, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed.
All as per item No. 18 here-in-before but except stones. (Note: Serviceable stones obtained from demolition shall be reused.)
M&L for cutting chases for pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth concealed water tubing all as specified and as directed..
S&F solid PVC door frame of size 50mm x 47mm made out of 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face all as specified and as directed.
S&F factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face , supplying & fixing in frame at site as per specification & drawing all as specified and as directed.
S&F 150 mm size aluminium anodised, barrel tower bolts of ex- truded section and fixed all as specified and as directed. .
S&F 100 mm size butt hinges medium weight, cold rolled mild steel, and fixed all as specified and as directed.
S&F 125 mm size extruded aluminium alloy handles, fabricated type, anodised all as specified and as directed.
S&F in repairs, galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aparture 1.18 mm fixed with wooden beads/tinned tacks or galvanised wire stapples to steel/wooden frame complete all as specified and as directed.
S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections conforming to Fe 410 -W (Gde- E- 250) quality- A ) including distance pieces, cleats etc. all as specified and as directed.
S&F mild steel framed work such as grills, framed guard bars and similar work conforming to Fe-290.Gde-E-165, welded to steel ventilators & window complete all as specified and as directed.
M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of colour as approved by GE, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and as directed.
M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of colour as approved by GE, having tensile strength of 550 Mpa as in roof covering/ridges/valley gutters/cladding to wall, fixed with self tapping screws as specified, coloure and design as approved by GE
S&F in repairs, 18/19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work including teak wood lipping all around of 18/19mm thick including french polishing for inbuilt cupboard shutters complete all as specified and as directed.
S&F in repairs, 18/19 mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminations fixed with screws to timber frame work/ with aluminum angle cleat all as specified and as directed.
M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.
M&L for 75mm thick PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base of floor all as specified and as directed.
M&L for machine cut kota stone flooring, 20-25 mm thick (size of kota stone slab 22"x22") laid over and including 20 mm thick bedding layer of cement mortar 1:6 jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed.
All as per serial item No. 35 here-in-before but 18 to 20 mm thick kota stone on vertical surfaces such as in skiting /dado of size as required at site over and including10 mm thick backing coat of cement mortar (1:4) complete all as specified and as directed.
M&L for machine cut Cudappah stone slab 20-25mm thick laid over and ncluding 20 mm thick bedding layer of cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.
M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exc 0.06 sqm but not exc 0.11 sqm, shade as approved by GE, as in floors etc., laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.
M&L for glazed coloured ceramic tiles 7mm thick (plain or printed), area of each tile exc 0.11 sqm but n exc 0.18 sqm, shade as approved by GE, as on vertical surfaces like dado, skirting etc laid over and including 10 mm thick backing coat in cement mortar 1:4, jointed in neat cement slurry and pointed in coloured cement to match with colour of tiles complete all as specified and as directed.
M&L for vitrified coloured ceramic tiles ,10 mm thick (square / rectangular), area of each tile n exc 0.36 sqm, shade as approved by GE in floor etc laid over and including 20 mm thick bedding layer in cement mortar 1:6, jointed in grey cement slurry and pointed in white or coloured cement to match with colour of tiles all as specified and as directed.
All as per serial item No 40 above but in dado / skirting or on vertical surfaces, laid over and including 10 mm thick backing coat in cement mortar 1:4 .
M&L for 60mm thick, factory made, chamfered edge, cement concrete interlocking paver block of M-35 grade with approved colour, design & pattern as in footparth, lawns, drive ways or light traffic, parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; etc complete all as specified and as directed.
M&L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick masonary surfaces or concrete surfaces, finished even and fair without using extra cement complete all as specified and as directed.
M&L for 10 mm thick rendering in cement mortar 1:6 on other than fair faces of brick masonry surfaces or concrete surface, finished even and smooth with sagol finish without using extra cement complete all as specified and as directed.
M&L for 5 mm thick rendering in cement mortar 1:3 on fair faces of brick or concrete surface, finished even and smooth with sagol, as in ceilings, complete all as specified and as directed.
M&L for raised pointing in cement mortar 1:3 to random or polygonal rubble, uncoursed or brought upto courses masonry, complete all as specified and directed.
S&F GI wire netting 0.90mm dia and 12mm mesh, fixed to wall, ceiling and beams etc including all laps, cutting, waste and making V grooves in crack portion and filled with cement mortar 1:2 etc complete all as specified and directed.
M & L for preparation of newly plastered or unplastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.
M & L for complete removal of existing treatment from old decorated surfaces of walls and applying three coats of white wash complete all as specified and as directed.
M & L for preparation of newly plastered or unplastered surfaces of ceilings and applying three coats of white wash complete all as specified and as directed.
M & L for complete removal of existing treatment from old decorated surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.
M & L for preparation of old plastered surfaces of walls and applying one coats of white wash complete all as specified and as directed.
M & L for preparation of old plastered surfaces of ceiling and applying one coat of white wash complete all as specified and as directed.
M & L for preparation of plastered or unplastered surfaces of walls and applying one coat of primer over a coat of 1 mm thick (average) white cement putty, sanding the surfaces till smooth finish is obtained and finally applying two coats of oil emulsion distemper etc complete all specified and as directed
M & L for complete removal of existing treatment, preparation of surfaces of walls and applying a coat of 1 mm thick (average) white cement putty, sanding the surfaces till smooth finish is obtained , one coat of alkali resistant primer and finally applying two coats of oil emulsion distemper etc complete all specified and as directed
M&L for preparation of old decorated plastered surfaces of wall including filling the holes and cracks with white cement and applying one coat of oil bound distemper complete all as specified and as directed.
M&L for preparation of old plastered surface of walls and applying one coat of cement base paint complete all as specified and as directed
M&L for preparation of old painted surfaces of wood or wood based materials of any description exceeding 10 cm width or girth and applying one coat of synthetic enamel paints complete all as specified and as directed.
M&L for preparation of old painted surfaces of steel and iron work of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.
Supply only mild steel galvanised chain link fencing , made out of GI wire, complete all as specified and directed. (Note :- Dia and mesh size shall be as decided by GE and weight of chain link fencing shall be decided by BOO ordered by GE)
Fixing only chain link fencing wire mesh, any type including securing bolts etc. and fixed complete all as specified & as directed.
S&F mild steel round bars as in line bars for fixing chain link fencing complete all as specified and as directed.
S&F mild steel bolt, machine made, 12 mm dia of shank with hexagonal or square head one end and screwed the other or screwed both end, each screwed end to be fitted with, washers and one hexagonal or square nut, not exceeding 15 cm long complete all as specified and as directed.
Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, bell push, holders, ceiling roses, pendants, regulators, sockets etc but excluding DBs, light fittings etc and making good disturbed surfaces of walls, floors etc. and matching with existing surface all as specified and as directed.
M & L for point wiring complete on surface of wall (open) type with two runs of 1.5 sqmm (22/0.30mm) for phase and neutral, single core, multistranded copper conductor cable of 1100 Volts grade,conforming to IS-694 1990, PVC insulated and unsheathed , FRLS cable drawn through and including PVC casing and caping (ISI marked) and its accessories such as Tee, elbow, jointer, elbow corner etc. fixed on surface of walls, coloumns/ beams alongwith 1.5 Sqmm (nominal area) copper conductor cable (multistranded) PVC insulated and unsheathed FRLS cable as earth wire connected to common earth dolly at one end and metalic bodies of luminaire/ fan at other end including PVC folding boards for mounting switches, sockets, fan Regulators, accessories etc as specified and directed for one light point or one fan point controlled by one, one way switch NOTE: 1.Proper colour coding shall be adopted for wiring (for phase-RED,YELLOW,BLUE for Earth-Green and Neutral-Black) 2. All points shall be earthed up to fixtures i.e holders,tube lights,all lights,ceiling lights,bulkhead lights,bldg security lights etc.
All as per serial item No. 65 here in before but one 5 Amp 5 pin socket outlet point on same board with other switches including earth wire as specified.
All as per serial item No. 65 here in before but on independent board.
All as per serial item No. 65 herein before but with 4.0 Sqmm (36/0.30mm), PVC copper stranded cable, FRLS type including PVC cable 2.5 Sqmm, FRLS type copper stranded conductor as earth wire connected to commen earth & earth terminals including PVC/wooden folding boards for mounting purposes for one 15 Amp 6 pin socket outlet point .
S&F switch piano, flush button, 5 Amp, single pole, one way, 230 volts, white finish, all as specified & as directed.
S&F socket outlet, flush type, 5 pin, 5 Amp, multipurpose, 230 volts, single pole, one way suitable for 3 pin/2pin, 5 Amp plug top white/ivory finish all as specified & as directed.
S&F switch socket combination, flush type, 5 pin, 5 Amp, multipurpose, 230 volts, single pole, one way, suitable for 3 pin/2pin 5 Amp plug top white/ivory finish all as specified & as directed.
S&F switch socket combination, multipurpose, flush type, 2 in 1 type (3 and 3 pin), 5/15 Amps, 230V, AC all as specified & as directed.
S&F lamp holder, angle/ batten type, PVC/Polycarbonate type with back plate, suitable for batten fittings all as specified & as directed.
S&F ceiling rose, surface PVC 50mm dia, 3 terminals including PVC mounting block white/ivory finish all as specified & as directed.
S&F fan regulator, step type, electronic on existing phenolic laminated sheet, 5 step, socket type, 230 volts, 450 watts, suitable for ceiling fan 1200/1400mm sweep all as specified & as directed.
S&F in repairs, 35 watt LED, post top lantern, new generation, energy saving, environmental friendly, long life aesthertically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source and IP-65 protection all as specified and as directed. Make : C&S cat No LTGL 00-00 /Havells Cat No RUBYPT35WLED757PSYMTOPC or equivalent model of make Philips /GE/Crompton/Halonix/Century LED ltd/Luker
S&F in repairs, LED Lights fitting 1 x 22 watt (4 ft), 220 volts, AC, decorative box type with driver, holder, including LED TUBE rod/light connecting up with and including three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make : Havells Professional Luminaries, cat No ENDURALINEARNEOBS22WLED865SPCWH or equivalent model of make Philips /GE/Crompton/Halonix/Century LED ltd/Luker.
S&F in repairs, MCB SP, AC 240 V, 6 to 32 Amps, 10 KA capacity ,'c' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.
S&F in repairs, MCB SPN, AC 240 V, 40 to 63 Amps, 10 KA capacity ,'c' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.
S&F in repairs, sheet metal enclosure (Factory made), double door shutter type for distribution board (when MCBs are to be used), single pole and neutral, 240 volts, 8 way, protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming As per IEC 61439-3, suitable for flush mounting and surface mounting, with 100 Amps rated copper busbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed.
All as per serial item No 80, but single pole and neutral, 240 volts, 4 way.
All as per serial item No 80, but triple pole and neutral, 240 volts, 4 way.
S&F in repairs, building security light fitting 35 watt 230 Volts, AC, outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 Protection complete acessories including one bracket made of Light grade GI Pipe 25 mm dia 1.5 mtr long fixed to wall/ pole with two clamps made out of MS Flat Iron 40 mm x 5 mm and connect to nearest electric supply by three core 1.5 sqmm aluminium cable all as specified and as directed.
Taking down, strip opening, cleaning all parts and packing of ceiling fan of any make and size and greasing ball bearing with specified quality grease and re-assembling the fan as a one unit and re-fixing ceiling fan at the existing site / rooms and connected with 23/0.0076 three core PVC flexible cable from ceiling rose to fan etc complete all as specified. Note : Replacement of spare parts, rewinding, painting, cable for connection etc to be measured and paid separately under relevant items of Sch 'A' Part mentioned here in after.
Taking down, strip opening, cleaning all parts and packing of exhaust fan of any make and size and greasing ball bearing with specified quality grease and re-assembling the fan as a one unit and re-fixing exhaust fan at the existing site / rooms and connected with 23/0.0076 three core PVC flexible cable from ceiling rose to fan etc complete all as specified.
M&L for preparation of old painted surfaces of ceiling fan of any make and size and applying one coat of synthetic enamel white paint by spray painting complete all as specified and as directed.
M&L for preparation of old painted surfaces of exhaust fan of any make and size and applying one coat of synthetic enamel grey paint by spray painting complete all as specified and as directed.
M&L in repairs, for short circuit /over heated winding from stator of ceiling fan of any make having 1200mm sweep with matching gauge and turns of super enamelled copper winding wire complete with leathered paper, glass sleeves, varnishing, baking etc all as specified and as directed.
M&L in repairs, for short circuit /over heated winding from stator of ceiling fan of any make having 1400mm sweep with matching gauge and turns of super enamelled copper winding wire complete with leathered paper, glass sleeves, varnishing, baking etc all as specified and as directed.
M&L in repairs, for short circuit /over heated winding from stator of exhaust fan of any make upto 300mm sweep with matching gauge and turns of super enamelled copper winding wire complete with leathered paper, glass sleeves, varnishing, baking etc all as specified and as directed.
M&L in repairs, for short circuit /over heated winding from stator of exhaust fan of any make exceeding 300mm but not exceeding 450mm sweep with matching gauge and turns of super enamelled copper winding wire complete with leathered paper, glass sleeves, varnishing, baking etc all as specified and as directed.
M&L in repairs for gun metal bush with suitable size, gun metal bush for ceiling fan any make, any size and sweep all as specified and as directed
M&L in repairs for ball bearing of size No 6201 for any type/make of ceiling fan including testing complete all as specified and as directed. Make : NBC/SKF/SBBI/TATA
M&L in repairs for ball bearing of size No 6202 for any type/make of ceiling fan including testing complete all as specified and as directed. Make : NBC/SKF/SBBI/TATA
M&L in repairs for canopy (top and bottom) of ceiling fans any make / size with canopy of matching colour all as specified and as directed.
M&L in repairs rubber reel with nut, bolts, split pins etc of ceiling fan with rubber reel heavy duty for hanging fan all as specified and as directed.
M&L in repairs for down rod with clamps etc of ceiling fan with down rod of 15mm bore medium grade GI pipe 0.45 metre long with clamps, bolts, nuts, split pins washers of suitable size of approved quality all as per specified and as directed.
M&L in repairs for down rod with clamps etc of ceiling fan with down rod of 15mm bore medium grade GI pipe 0.60 metre long with clamps, bolts, nuts, split pins washers of suitable size of approved quality all as per specified and as directed.
M&L in repairs for down rod with clamps etc of ceiling fan with down rod of 15mm bore medium grade GI pipe 1.50 metre long with clamps, bolts, nuts, split pins washers of suitable size of approved quality all as per specified and as directed.
M&L in repairs for connector block of ceiling fan of suitable size of approved quality all as per specified and as directed.
M&L in repairs for capacitor of ceiling fans with capacitor having capacity 2.5mfd, 240 Volts all as per specified and as directed. Make : Bajaj/Epcos/Havells
M&L in repairs for capacitor of ceiling fans with capacitor having capacity 3.15mfd, 240 Volts all as per specified and as directed. Make : Bajaj/Epcos/Havells
M&L in repairs for capacitor of ceiling fans with capacitor having capacity 4mfd, 240 Volts all as per specified and as directed. Make : Bajaj/Epcos/Havells
M&L in repairs for blades of 1200mm sweep ceiling fan of any make with aluminium blades duly painted including provision of screws etc fixing purpose complete all as specified and as directed.
M&L in repairs for blades of 1400mm sweep ceiling fan of any make with aluminium blades duly painted including provision of screws etc fixing purpose complete all as specified and as directed.
M&L in repairs for cable/wire for connection of fan with flexible copper cable 3 core of size 23/0.0076 all as specified and as directed.
M&L in repairs for clamp of down rod for hanging of ceiling fan with nuts, bolts, washers and split pin complete all as specified and as directed.
M & L for sub main wiring with 2 runs of 10 sqmm, (for phase and neutral) single core, PVC insulated & unsheathed FRLS cable conforming to IS-694, 1100 volts with copper conductor, multi stranded drawn in and including suitable size heavy grade rigid PVC conduit/PVC casing caping (ISI marked) with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 6 sqmm single core PVC insulated & unsheathed FRLS copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board and testing on completion including taking down old submain wiring and any type of conduit/casing caping complete all as specified and as directed. NOTE: 1.Proper colour coding shall adopted for wiring (for phase-RED,YELLOW,BLUE for Earth-Green and Neutral-Black) 2.Two runs of 10 sq.mm cable(for phase and neutral), one run of 6 sq.mm cable (for earthing) and one run of PVC conduit/casing & caping shall be measured as one unit.
All as per serial item No 108, but 2 runs of 6 sq.mm cable (for phase and neutral) and one run of 4 sq.mm cable for earthing. NOTE: 1.Proper colour coding shall adopted for wiring (for phase-RED,YELLOW,BLUE for Earth-Green and Neutral-Black) 2.Two runs of 6 sq.mm cable(for phase and neutral), one run of 4 sq.mm cable (for earthing) and one run of PVC conduit/casing & caping shall be measured as one unit.
All as per serial item No 108, but 2 runs of 4 sq.mm cable (for phase and neutral) and one run of 2.5 sq.mm cable for earthing. NOTE: 1.Proper colour coding shall adopted for wiring (for phase-RED,YELLOW,BLUE for Earth-Green and Neutral-Black) 2.Two runs of 4 sq.mm cable(for phase and neutral), one run of 2.5 sq.mm cable (for earthing) and one run of PVC conduit/casing & caping shall be measured as one unit.
Supply , fixing and testing, ALL-IN-ONE Solar Street Light fitting, 20 Watts LED lamp, Range -(2 days backup), including LED Light, MPPT SCC, Mono Crystalline SPV Panel, LiFeP04 Battery with tamper proof MS box with corrosion resistance paint suitable for battery , bend pipe and clamps suitable for mounting lamps fixtures complete including providing HDG tubular pole 6 m TUB Pole(B) above ground, designed to specifycally for Solar light fitting, including PCC work & foundation (as per manufacturers instructions), earth work if required for embedding the pole in ground, including suitable size of cable, including taking out existing street light fitting with pole complete all as specified and as directed. Make- Havells, FG code LHSTAKU7CBAF020 HSN Code 8541 or equivalent model in Phillips/ Wipro/ Crompton/HPL/Luker/Halonix.
M&L in repairs/replacement earthing complete with galvanized steel earth plate electrode 600 mm X 600 mm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to the GI wire 4 mm dia , by means of nut bolts, check nuts and washer of the GI . Earth wire connected upto main earth point/DBs alongwith 15mm dia GI pipe, medium grade, including provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick RCC (1:2:4) cover with reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified including testing on completion.
M/s Meher Construction
Vinod Enterprises
Arihant Construction
M/S. Z.K.ENTERPRISES, AHMEDNAGAR
MS. A.S. CONSTRUCTION
AMAR CONSTRUCTION
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.PDF
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .