SPL REPAIR TO ELECTRIC AND WATER SUPPLY INSTALLATION, MANEKSHAW GATE INSTALLATION, VENUS INSTALLATION ROBINSON PUMP HOUSE, FOUR TANK INSTALLATION NEAR KB 01, OPERATOR ROOM OF PH NO 37, MAIN POWER HOUSE AND INSTALLATION OF ZONE C AREA OF GE (E) JBP

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

Taking down cement plaster on brick/concrete/stone surfaces including racking out jointing, hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

Demolition of brick work/stone masonry/PCC block masonry built in cement mortar or cement lime mortar including all quoins, pillars, arches etc, but excluding ashlar facings dressed stone work and precast concrete articles complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m deep for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm in plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning filling including spreading, leveling, watering and well ramming in layers n.exc 25 cm thick in soft loose soil complete all as specified and directed.

Removing excavated soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above starting point complete all as specified and directed.

M&L for PCC 1:4:8, type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M&L for brickwork with fly ash bricks of old size straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

Use & Waste of Formwork for rough finished surfaces (flat) to sides of concrete foundation, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation, plinth beams and similar work, vertical or to batter complete all as specified and directed.

Use & Waste of formwork for rough finished surfaces (flat) (square, rectangular or polygonal) to sides of pillars, posts, struts, piers, columns and stanchions , flat complete all as specified and directed.

Use & Waste of formwork for rough finished surfaces (flat) to sides and soffits of floor or roof beam, beam haunchhings, girders, lintels, cantilevers, shelves incl supports overhangs etc also splays between floors and beams etc complete all as specified and directed.

Use & Waste of formwork for rough finished surfaces (flat) to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work n.exc 200mm thick (horizontal or sloping) complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel round bars 10mm dia and over Gd-I, IS 432 (Part-I), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5mm dia and over and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookihg ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for reinforced cement concrete M-25 design mix (20mm graded stone aggregates) in foundation, including rafts, footings, foundations beams, plinth beams, bases of columns etc, basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete M-25 design mix (20mm graded aggregates) in columns, pillars, piers, posts and struts etc etc complete all as specified and directed.

M&L for reinforced cement concrete M-25 design mix (20mm graded aggregates) in beams, cantilevers, bressummers, lintel over 1.5m span complete all as specified and directed.

M&L for reinforced cement concrete M-25 design mix (20mm graded aggregates) in suspended slabs supported on walls, beam and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for brick work with old size fly ash bricks straight or curved on plan excl 6m mean radius built in CM 1:6 etc complete all as specified as directed.

Dismantling wrought iron or mild steel work including doors, gates but excl framed trusses etc complete all as specified and directed.

M&L for Mild Steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F rolled mild steel as in stairs (framed) including stringers, treads, landing, balusters, hand rails etc including cleats, brackets, etc confirming to Fe 410-W (Gde E-250 quality-A) complete all as specified and directed.

M&L preparing new steel surfaces exc 10 cm width or grith and applying two coat of synthetic enameled paint over a red oxide primer complete all as specified and directed.

M&L for preparation of new steel surfaces not exc 10 cm width or grith of any description and applying two coats of synthetic enamel paint ordinary tint over one coat of red oxide complete all as specified and directed.

M&L for dewatering and desludging of underground or semi underground water storage sump of capacity 50,000 to 1,00,000 gallon including scraping down wall and bottom surface using steel wire brush, taking out and removing sediment/loose dirt/mud sludge, vedgetation and other foreign materials completely from tank and washing repeatedly with water the inside surface of tank with bleach solution and water including all reqd T&P complete all as specified and directed.

Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured by M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd} at the rate of 0.40 Kg/Sqm, torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions complete all as specified and as directed. Notes : (i) Coved fillets in PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/ other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm. (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mm x 25mm (minimum) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimny/other vertical surfaces and polimeric membrane insterted in groove and sealed with paving bitumen. (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 150 ml/Sqm. (vi) Above aspects are deemed to be included in quoted rate.

M&L for rendering 15 mm thick on brick work or concrete surfaces in CM (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on brick work or concrete surfaces in CM (1:4) finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick on brick work or concrete surfaces as in ceiling in CM (1:3) finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing surface of newly plastered walls and applying two coats of oil bond distemper over alkali resistant priming preparatory to distempering complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over one coat of chalk whitening complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling and applying one coat of white (lime) wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls and applying one coat of white wash (lime) complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls and applying one coat of distemper oil emulsion complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls and applying one coat of cement base paint complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc complete all as specified and directed.

M&L for cement concrete 1:2:4, Type B-2 using 40mm graded stone aggregate in foundation, filling and mass concrete complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4, Type B-1 using 20 mm graded stone aggregate complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20 to 25mm thick over & including 20mm thick cement screed in CM 1:6 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Kota stone slab 20 to 25mm thick in riser steps, skirting or dadao and pillar laid over & including 10mm thick screed in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for coloured non skid joint free ceramic tiles 7 to 8 mm thick (square or rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floor etc laid over and including 15mm thick cement screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for coloured non skid joint free ceramic tiles 7 to 8 mm thick (square or rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, as in skirting over and including 10mm thick cement plaseter in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

S&F Glazed ceramic coloured tiles (450 x 300)/ (350 x 250) x 7 to 8mm thick, in dado/skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10 mm thick screed in CM 1:4 complete all as specified and directed.

Taking down chowkhat or frames n.exc 1.5 sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Taking down chowkhat or frames exc 1.5 sqm and n.exc 4.00 sqm each (without taking of shutter from frame) and removing from site complete all as specified and directed.

S&F factory made soild PVC door frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet reinforced with mild steel square tube and edges will be painted to match with single side prelam sheet as per specification and drawing given on MES schedule Part-II (2020) complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC `C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail bottom rail on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stile & rails with suitable PVC sheet beading & joined together with solvent cement specified and shown on drawing complete all as specified and directed.

M&L for second class hardwood plain straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

S&F 35 mm thick second class hardwood factory made glazed and skelton shutters open rebated and prepared to receive glass, gauge, etc (without sash bars), edges of framing plain, chamfered or founded, fitted with cut and mitred beads for securing glass, etc, sizes of members of the shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a) complete all as specified and directed.

M&L for 35mm thick second class hardwood plain, framed, panelled shutters (two panel) with lock rail and panel of 9mm thick B.W.P. commercial ply or 12mm thick veneered partical board with commercial veneering on both faces. The size of rails and styles as per IS:1003 (Part-I) kiln seasoned and chemically pressure treated supplied and fixed to chowkats complete all as specified and directed.

S&F steel window with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars dovetailed or welded complete all as specified and directed.

S&F steel window with side hung shutters including projecting type hinges with steel handle, and steel pegstay, complete without glazing bars dovetailed or welded complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay etc complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty etc in square n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty etc in square n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 100 mm long Mild steel butt hings medium weight complete all as specified and directed.

S&F 125 mm extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and directed.

S&F 150 mm long aluminum anodized barred tower bolts of extruded section complete all as specified and directed.

S&F 300 mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixed complete all as specified and directed.

M&L for preparation of new wooden surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint ordinary tint over one coat of pink primer complete all as specified and directed.

Taking up or down 25mm bore steel water tubing & connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 25 mm bore medium grade galvanished tube with all fitting & fixed complete to walls or ceiling or laid in floors/trenches complete all as specified and directed.

Taking up or down 20mm bore steel water tubing & connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 20 mm bore medium grade galvanished tube with all fitting & fixed complete to walls or ceiling or laid in floors/trenches complete all as specified and directed.

Taking up or down 15mm bore steel water tubing & connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 15 mm bore medium grade galvanished tube with all fitting & fixed complete to walls or ceiling or laid in floors/trenches complete all as specified and directed.

Dismantling water tanks exc 500 and n.exc 1000 Ltr capacity and removing to store complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) of 750 Ltr storage capacity (having two layered and ISI marked) hoisted and fixed in position all as spcified in SSR Part-I and including S&F 20mm bore ball brass valve, high pressure with polythene float & fly nut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair 20mm bore Gun metal gate valve with iron wheel head screwed both end for iron pipe complete all as specified and directed.

S&F in repair 25mm bore Gun metal gate valve with iron wheel head screwed both end for iron pipe complete all as specified and directed.

S&F in repairs 15mm bore, pillar taps, cast copper alloy, fancy type, with capstan heads, chromium plated, scewed down high pressure, with or without lettered 'Hot' or Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs 15mm bore Bib tap, cast copper alloy, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs 15mm bore, angle/stop cock, fancy type, chromium plated, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair PVC valveless syphonic action type flushing cistern 10 Ltrs capacity low lwvel, white with inlet ball valve, float and handle for low level cistern complete all as specified and directed. complete all as specified.

S&F in repairs water closet vitreous China (squatting pan) complete including provision of lime concrete bedding vitreous china squatting pan orrisa pattern of size 580 x 440 mm, white, with CI 100mm bore 'P' or 'S' trap front or back inlet and foot rest any pattern excluding flushing cistern complete all as specified and directed.

S&F in repair waste fittings, brass chromium plated for glazed ware sinks, basins, urinals etc with long screw shank and fly nuts, flange end bedded in red lead cement and other fixed ccomplete all as specified and directed.

S&F in repair 32mm bore low density poly ethylene pipes (LDPE), 1.0 m long of pressure rating 6Kgf/Sqcm fixed to wash hand basin complete all as specified and directed.

S&F in repairs 15mm size PVC connection with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repairs vitreous China Wash Hand Basin, white, flat back size 550 × 400 mm including cutting for and pinning in ends of brackets including brackets but exclusive taps,waste, chain and leg porcelain stop pan complete all as specified and directed.

M&L for servicing of steel rolling shutters of any size including taking down, greacing, oiling, replacement of any rusted or broken screws and nut bolts, adjustment and easing of locking arrangement and refixing rolling shutter in the same opening complete all as specified and directed.

M&L for kerb stone of PCC 1:2:4, Type B-1 using 20mm graded stone aggregate of size 450 x 300 x 80mm and setting in CM 1:6 complete all as specified and directed.

M&L for cement concrete 1:2:4, Type B-1 using 20mm graded stone aggregate as in coping and the like including weathering, slightly rounded or chamfered angles and throating as directed complete all as specified and directed.

Supply and spreading broken stone boulder of gauge n.exc 63mm gauge in loose filling as and where directed.

M&L for 100mm thick cement concrete 1:4:8, Type D-2 using 40mm graded stone aggregate as in sub base for interlocking tile footpath complete all as specified and directed.

S&F factory made rubber moulded glossy finished Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for sand cusion under interlocking paver block including spreading and levelling and filling interstices complete all as specified and directed.

M&L for 60mm thick precast coloured interlocking paving blocks factory casted using grey cement with pigment, machine pressed confirming to IS-15658-2006 and of shape haxagon/ triangular/ zigzag/ I-shaped etc. as directed having compressive strength not less than 350 Kg/ Sqcm complete all as specified and directed.

Dismantling post or struts (RCC) embedded in concrete, any section, incl taking out embedded portion and making good disturbed ground complete all as specified and directed.

Excavating in post holes (or similar holes) each n.exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25cm in soft/loose soil complete all as specified and directed.

M&L for joist, channel, angle, MS flat or tee sections of quality Fe-410W (Gde E-250 quality A), fixed independently, without connecting plates etc cut to ordinary lengths i.e. within 20mm of the length indicated complete all as specified and directed.

M&L for PCC 1:3:6, type C-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for mild steel screw bolts 11-15mm dia (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends eacn screwed end to be fitted with washer and one hexagonal or square nut n.exc 5cm long complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wires complete all as specified and directed.

Supply only chain link MS galvanised fencing, any size and type complete all as specified and directed.

Providing precast concrete 10:2:4 louvers and jallies, Type B-0 using 12.5mm graded stone aggregate, 35mm thick (measured solid) set in CM 1:4 including all moulding but excluding frame complete all as specified and directed.

Eraction and fixing only joist, channel, angle or tee sections, fixed independently, without connecting plates etc complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, bell, bell push, regulators, sockets etc removing material for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Taking down carefully unservicable/partly unservicable street light/light fittings any type, tube light fitting and fixtures, etc, and making good to the disturbed surfaces of walls/floor etc to match with existing surfaces including white washing/colour washing/ distempering complete all as specified and directed.

M&L Point wiring with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm stranded for earth continuity wire, to be drawn in and including, PVC medium grade conduit not less then 20 mm width with MS sheet metal sunken switch/Terminal box 1.2 mm thick and ebonite switch board cover 3.0 mm thick or PVC moulded switch board and brass screws with cup washers including all necessary wall cutting and making good disturbed surface complete all as specified and directed. Note : (i) Making good to match with the adjoining surface shall be included in the unit rate. (ii) Rate is inclusive of Cutting/chases of wall/floor/ceiling.

One light point controlled by one switch complete all as specified and directed.

One ceiling /exhaust fan point controlled by one switch complete all as specified and directed.

One 3 pin socket outlet, 5 Amps on the same board with other switches complete all as specified and directed.

One 3 pin socket outlet, 5 Amps on independent board complete all as specified and directed.

One 3 pin socket outlet, 15 Amps, independent, with cables 4 sqmm size complete all as specified and directed.

M&L for modular switch, 1 way, 6 Amps, 1 module complete all as specified and directed.

S&F modular Socket, 6 Amps, 2/3 pin combined, 2 module complete all as specified and directed.

M&L for modular switch socket outlet, 3 pin, 6 Amps, flush type complete all as specified and directed.

M&L for modular switch socket combination, 16 Amps, 6 pin, 3 Module complete all as specified and directed.

S&F Ceiling rose, 3 phase/PVC/Polycarbonate, isolated body complete all as secified and directed.

S&F Bell push, flush type 5 Amps complete all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as required complete all as specified and directed.

S&F Lamp holder insulated body with back plate for angle holder complete all as specified and directed.

S&F LED lumanaire 600mmX600mm , 36 Watts 220V AC recessed type with high Efficiency PMMA diffuser soft glare free light complete with driver, holder and LED lamp suitable for roof ceiling including connecting up with 3 core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED light fittings 1 x 20 Watts, 220 Volts, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F sheet metal enclosures with single pole and neutral enclosure with 2 pin and earth plug sokcet with MCB SP 20 Amps complete all as specified and directed.

Taking down ceiling fan/Exhaust fan of any size or make and depositing it in MES Store complete all as specified and directed.

S&F Sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 6 Sqmm, earth continuity conductor of size 6 Sqmm to be drawn through and including PVC conduit 25 mm dia medium grade conceled in walls/roof/floors complete all as specified and directed. Notes : (i) Two wires of 6 Sqmm and one wire of 6 Sqmm and one run of PVC conduit shall be measured as one unit.

S&F Sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 4 Sqmm, earth continuity conductor of size 4 Sqmm to be drawn through and including PVC conduit 25 mm dia medium grade conceled in walls/roof/floors complete all as specified and directed. Notes : (i) Two wires of 4 Sqmm and one wire of 4 Sqmm and one run of PVC conduit shall be measured as one unit.

S&F MCB DB made of sheet steel, powder painted with Neutral bus bar 200 Amps, neutral link, earth bar and Din rail, 240 Volts SPN with 8 way Single door, IP-43-IK09 protection grade complete all as specified and directed.

S&F MCB/Isolator SPN 240 Volts, 'C' series, breaking capacity 10 KA of rating 40Amps complete all as specified and directed.

S&F MCB/Isolator SP 40 Amps 240V complete all as specified and directed.

S&F Isolator TPN 100 Amps , 415Volts complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60 cm x 6mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level connecting to and including GI earth wire of size 4.0 mm by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia medium grade pipe for protection of GI wire to the extent of 7.5 mtrs asearthing lead including charcoal dust and salt packed all around the earth plate in the earth pit all as per Electrical plate No 3 of SSR Part-I (2009) including PCC foundation/chamber in mix 1:2:4 type B1 with angle iron frame CI frame, CI cover with provision of locking arrangement and 20 mm dia light grade GI pipe from top edge of the earth plate upto MS funnel with wire mesh provided inside the concrete earth pit for watering arrangement complete including excavation and earthwork in any type of strata and testing complete including fill up the earth pit with soil for best result and removal complete all as specified and directed. Note :- Earth protection pipe & earth wire upto and including 7.5 m length is deemed included in unit rate quoted by the contractor.

S&F LED street light fitting 35 Watts, 230 Volts, AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corossion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S&F Ceiling fans, complete with three blade, down rod, accessories 230 Volts, 1200 mm sweep with squirrel cage induction motor complete all as specified and directed.

S&F Exhaust fan, steel body AC single phase, 230 Volts of size 300mm sweep with blades and frames and louvers complete all as specified and directed.

Schedule of credit amount of Rs. 45,537.00 to be deducted during AOC.

Sachdeva Enterprises (BID ID -3126006)

SHRI KRISHNA CONSTRUCTIONS (BID ID -3114861)