Office Building Kotkapura

Amount

5.2(i)/Carriage of Jallalabad Sand Total lead 80 KM Payable lead 75 KM

5.2(i)/Carriage of Pathankot Sand & Bajri Total lead 280 KM Payable lead 275 KM

6.6/Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm layers with compaction including disposal of all surplus soil as directed within a lead of 30 meters.

6.8(a)(i)/Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar up to 40% excavated from foundation and taken only from outside the building plinth in 15 cm layers including ramming, watering and consolidating lead up to 30 metres

9.1/Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering)

9.6/Centring and shuttering for sides and soffits of beam, beams launchings girders bressumers, lintels

9.8/Centring and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.

10.9(b)(ii)/Cement concrete 1:5:10 with 40 mm stone ballast using concrete mixing volumetric type

10.15/Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth.

10.20/Reinforced cement concrete M-15 mechanicaly batch mixed using batch type concrete mxier as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth.

11.3(i)/First class burnt brick work laid in cement sand mortar 1:6 in foundation and plinth.

11.4(i)/First class burnt brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level.

11.29(a)Extra rate for First Floor

11.34(a)/115 mm thick brick wall with every fourth course reinforced with hoop iron laid in 1 :4 cement sand mortar in super structure

13.13/Terracing consisting of tiles 22.86 x 11.43 x 3.83 cm laid over 25 mm mud plaster 7.5 cm mud filling on another laver of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg/sqm top of CC slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing etc.

13.45/Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16.

13.51/Bottom Khurra on ground 1.2m x 0.6m consisting of brick on-edge laid in cement mortar 1:3 over 75mm cement concrete 1:8:16 including 12.5mm thick cement plaster 1:3

13.55/Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified.

13.74/Providing and fixing 110 mm dia SWR U.P.V.C Rain water pipe (ring fitted type-A) as per IS:13592 including jointing during masonary complete as per specifications and to the entire satisfaction of Engineer-in-charge. (If fixed on wall face clamp to be paid separatly as per respective item)

13.75/Providing and fixing 110 mm dia SWR U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer-in-charge.

13.76/Providing and fixing 110 mm dia SWR U.P.V.C Coupling/Sockete for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge.

14.3/Base course of floor consisting of 100 mm thick cement concrete 1:8:16 with stone aggreate and 100 mm sand filling.(using mechanical mixer for mixing of material)

14.84/Kota stone slab 20-25 mm thick flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry, mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand).

14.86/Kota stone tiles 20mm thick in skirting risers of steps, dado walls and pillars laid in 2.5mm thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone, including rubbing and polishing.

14.112/roviding and laying vitrified floor tiles in different sizes in light colour shades made using Soluble Salt Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. ( Soluble salt Print Penetration should be up to 1 to 2 mm after the tiles are fired & polished ). (a)/Size 600 mm x 600 mm

14.135/Providing and Laying Out Door Precast Designer chequered tiles of any size & any shape 25mm thickness having top layer of white cement mixed with pigment, laid on 20mm thick bed of ordinary cement mortar 1:3 (1 ordinary cement :3 fine sand), joints grouted with white cement slurry containing pigment to match the shade complete in all respect as per specifications and to the entire satisfaction of engineer-in-charge.

14.142/Providing and fixing Morwad Marble Strip 12mm to 15mm thick and 100 mm wide in kotah stone flooring over 12.50mm thickness base of cement mortar 1:3 jointed with cement slurry including cost of additional mortar equivalent to the kota stone thickness andcolouring pigment to match the colour rubbed and polished to granolithic finish complete in all respects.

15.9/12.5 mm thick cement plaster 1:4

15.10/12.50 mm Cement Plaster 1:5 on walls

15.20/20 mm thick Cement Plaster 1:4 in two coat work.

15.21/20 mm thick Cement Plaster 1:5 in two coats work.

15.52/Bearing Plaster of 10 mm thick cement mortar 1:3 cement sand finished with a floating coat of neat cement and thick coat of Lime wash / P.O.P. on top of walls when dry for bearing of R.C.C. slabs & beams.

18.50/Supplying and fixing of GI sheet frames (Chowkat) consisting of 18 gauge (1.25mm) thick steel sheet of the specified section (standard design latest), including iron lugs (hold fasts) iron hinges conforming to PWD specifications including bolts for fixing steps, lock notch provision for receiving tower bolts and finished, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:2:4 for lugs complete to the satisfaction of Engineer-in-charge. (a)Doors and windows frame of size 118mm x 60mm with 40 mm wide single rebate weighing 3.43 kg per meter.

(b)/Doors frame of size 125 mm x 60 mm with 37 mm wide double rebate for 35 mm door shutter.

18.50/Supplying and fixing of GI sheet frames (Chowkat) consisting of 18 gauge (1.25mm) thick steel sheet of the specified section (standard design latest), including iron lugs (hold fasts) iron hinges conforming to PWD specifications including bolts for fixing steps, lock notch provision for receiving tower bolts and finished, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:2:4 for lugs complete to the satisfaction of Engineer-in-charge. (b)/Doors frame of size 125 mm x 60 mm with 37 mm wide double rebate for 35 mm door shutter.

17.10(xvii)(a)(i)/Hollock wood doors shutter windows shutter including hinges, screws, chocks, cheats, stops cords etc. complete fixed in position. panelled, glazed or glazed and panelled. 40 mm thick

17.11(ii)(a)/Wire gauge Hollock wood door shutter without springs housed in chowkhat. 35mm thick

18.26/Extra for providing & fixing Steel beading of approved shape steel tube beading size 12mm x 12mm, 18 gauge of approved shape and section with screw for fixing of glass panes instead of glazing clips and metal slash putty in steel doors , windows & Ventilators complete in all respect.

18.25/Supplying and fixing glass panes with glazing clips and special metal sash putty of approved make. (b)Glass panes 4mm or 10.75 kg / sqm exceeding 0.4 sqm of area

18.4/Wrought iron and mild steel ladders, framed grills, grating etc. with ends of bars, riveted or welded or forged, framed window guards, barred iron doors, stair case, iron railing including cost of bolts and nuts or screws or welding rod, complete fixed in position.

18.49/Providing Polyster Powder coating 60 to 70 micron any coloured specrified to M.S Grill section of various sizes including carrriage of material from marktet to workshop .

NS/Earth filling with good quality earth obtained from outside the plinth including compensation of earth, loading, unloading, carriage from outside the premises to site of work, spreading, laying watering compacting with rammer complete as per specifications.

NS/Providing and fixing 16 gauge stainless steel pipe of various sizes railing of grade 304 duly fixed on ramp with the help of bolts grouted on floor with hand rail and newel post of 50 mm dia stainless steel pipe, balusters of 40 mm dia stainless steel pipe complete in all respect as per specification and entire satisfaction of Engineer-in-Charge. (Railing on Entrance Ramp Design as per guidelines issued for persons with disability)

17.27/Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position (Code : II Revision IS-2191 Part-I) 1973 (a)(iv)/Commercial with elm or gurjan facing on both \ Sides with laminated core and lipped edges:- 35 mm thick

17.23(i)/Cost of Aluminium fittings complete for doors, windows such as tower bolts, handless and screw etc. for these fittings (Excluding sliding bolt)

17.49(a)/Providing and fixing aluminium sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300 mm x 16 mm

17.44/Providing and fixing 0.50 mm thick aluminium sheet including cost of necessary fittings i.e. screws, etc. complete

17.43(c)/Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete - I.S.I Designation No. III (size of door 851 mm to 1000 mm)

17.37(a)/Providing and fixing 12mm thick 150mm wide pelmets with 25mm dia Aluminium rod and brackets including fixing with 25mmx3mm MS Flat 10cm long and PVC Plug etc complete. Deodar Wood

18.18/Cold twisted deformed (Ribbed/ Tor Steel Bar) Bars Fe 500 grade as per IS 1786-2006, for R.C.C works, where not including in the complete rate of RCC including bending and placing in position complete

15.7+15.48/12.5mm thick cement plaster 1:2 with cement rendering (Inside)

16.65/Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two coats to get required finish.

16.31/Applying priming coat with cement primer in all shade on newly plastered or concrete exterior surface

16.63/Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two coats)

16.15/Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fillers consisting of white lead, linseed oil, Varnish, and Chalk Mitti including finishing the surface to required finish complete.

16.16/Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc.

16.17/Painting two coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. - With ordinary quality Paint

16.60/Finishing walls with Premium Acrylic smooth exterior paint with silicon additives of required shade with two coats applied @ 1.43litre/10 sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm.

10.11(b)(ii)/Cement Concrete 1:4:8 with stone ballast of size of 40 gauge using mechanical mixer.

24.58/Construction of unreinforced plain cement concrete pavement in M-30 mix design over a prepared sub base with cement contents 350 kg per cum and coarse and fine aggregates conforming to IS:383 mixed with concrete mixer using weigh batcher, laid in position over 125 micron thick polythene sheet, compacted with needle vibrator, screed vibrator and plate vibrator, dewatering of free water with vaccum pump, finishing the surface with power floater, including provision of contraction and expansion joints as required, finishing to required lines and grades as per drawings and technical clause 1501 of MORD specifications

14.137/Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-35 grade machine made rubber moulded smooth finish with strong vibratory process or with vibro hydraulic compaction machine and of approved size and design / shape laid in Ordinary Grey and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in-charge ( IS Code : 15658-2006)

14.138/Providing and laying 60 min thick cement concrete Interlocking paver block of M-35 grade machine made rubber moulded smooth finish by strong vibratory process and or with vibro-hydraulic compaction machine of approved sire and design / shape laid in Dark Fast Colour and pattern over and Including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer in-Charge for Light Traffic Areas such as Pedestrian plazas, shopping complexes, ramps, car parks, office driveways, housing colonies, Office driveway, housing colonies, office complexes, rural roads with low volume traffic, farm houses, beach sites, tourist resorts, local authority footways, residential roads, etc.

14.135/Providing and Laying Out Door Precast Designer chequered tiles of any size & any shape 25mm thickness having top layer of white cement mixed with pigment, laid on 20mm thick bed of ordinary cement mortar 1:3 (1 ordinary cement :3 fine sand), joints grouted with white cement slurry containing pigment to match the shade complete in all respect as per specifications and to the entire satisfaction of engineer- in- charge.

Internal Sewerage System

30.74(i)/Providing and fixing in position H.C.I. soil waste vent or antisyphonage pipes to I.S.I. specification (IS:1729) of approved make (to the approval of Engineer-in-charge ) including cutting, jointing, wastage, but excluding cost of lead jointing. (b)/100 mm i/d HCI pipe line laid complete

30.74(iii)/Providing and fixing in position SWR UPVC soil waste vent or antisyphonage pipes as per IS -13592 of approved make (to the approval of Engineer-in-charge)including cutting, jointing, wastage, but excluding cost of lead jointing. (b)/110 mm o/d SWR UPVC pipe line laid complete

(c)/90 mm o/d SWR UPVC pipe line laid complete

30.76(b)/Providing and fixing in position gratings 150 mm x 150 mm on top Khura PVC grating.

30.78(a)/Providing and fixing in position M.S. or heavy flat iron clamps made out of M.S. flat iron not less than 5 mm of the approved design for fixing C.I. soil waste, vent or antisyphonage pipes to walls complete in all respects. Including cutting and making good the walls and floor etc. and painting.

30.81(i)/Providing and fixing in position H.C.I specials for soil waste vent or anti syphonage pipes to I.S.I specifications (IS:1729) of approved make (to the approval of Engineer-in-charge) including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining. (vi)/Cowls

30.81(iii)/Providing and fixing in position SWR UPVC specials for soil waste vent or anti syphonage pipes as per as per IS - 14735 of approved make (to the approval of Engineer-in-charge) including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining. (B)/For 110 mm o/d pipes (v)/Bend Plain

(viii)/Collar

(D)/For 75 mm o/d pipes (v)/Bend Plain

(vii)/Collar

(viii)/With 75 mm i/d outlet deep seal at ground floor

30.99/Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150 mm x 150 mm , cover and frame clear opening 300 mm x 300 mm and out of side size 330 mm x 330 mm and chamber including cost of all bricks work in cement mortar 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50 mm. (a)/100 mm internal Diameter S.W. Gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300 mm x 300 mm and out of side size 330 mm x 330 mm

29.60/Construction of brick masonry inspection chambers size as given below up to 0.60 metre average depth in 1:5 cement sand mortar, lime concrete with 40 per cent lime mortar 2:3 in foundation, cement concrete 1:2:4 benching 12.50 mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement, R.C.C. 1:2:4 slabs 100 mm thick cement concrete topping 50 mm thick with 455 mm x 455mm, 455 mm x 610 mm inside light duty C.I. inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design. (a)/Size 450 mm x 450 mm inside with RCC 455 mm x 455 mm cover and frame light duty double seal

28.11/Providing, laying, jointing, fixing and testing ISI Marked uPVC Pipe with G.I. specials as per ISI-4985, including cost of G.I. specials such as tees, bends, sockets, elbows etc. testing inside building complete. (B)(b)/uPVC Pipe 6 Kgf/cm2 - 50 mm i/d

Internal Water Supply System

28.35/Providing, laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) B-Class Premium make such as (Jindal Hisar) including cost of specials (such as tees, bends, sockets, elbows etc.), painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete. (a)/15 mm i/d

(b)/20 mm i/d

(c)/25 mm i/d

(e)/40 mm i/d

30.85(a)/Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes line and making good the same to its original condition. Size 75 mm x 75 mm G.I. Pipe 15 mm i/d to 25 mm i/d

28.56/Cutting holes up to 23 cm square through B.B. in cement walls or stone masonry wall in cement for pipes, and making good the same & finishing according to existing finish where required. (a)/Through wall 11.43 cm thick

(b)/Through wall 22.86 cm thick

28.40/Providing, fixing and jointing G.I Union Couplings (of approved make with the approval of EIC) as per IS 1879 in G.I. Pipe lines complete in all respect. (a)/15 mm i/d G.I. Union

(b)/20 mm i/d G.I. Union

(c)/25 mm i/d G.I. Union

(e)/40 mm i/d G.I. Union

28.44/Providing, fixing and jointing Brass Ball valves screwed with SS/BRASS ball & spindle & Teflon seats, on G.I. Pipe lines including all carriages complete. (c)/25 mm i/d Brass Ball valves

(e)/40 mm i/d Brass Ball valves

28.52/Painting G.I. Pipes and Specials with synthetic enamel Paint in all shades as per I.S.I. specification on existing or new work, two coats paints including cleaning rubbing surface, etc. (a)/15 mm & 20 mm i/d G.I. Pipe

(b)/25 mm & 32 mm i/d G.I. Pipe

(c)/40 mm & 50 mm i/d G.I. Pipe

Sanitary Installation

30.2/Providing and fixing in position Chinaware Indian Orissa water closet size 580 mm of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern including cost of PVC long bend 32 mm dia complete in all respect and to the entire satisfaction of Engineer-in-charge.

30.4/Providing and fixing in position Chinaware European type water closet P trap or S trap of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern, PVC short bend 32 mm dia including cost of seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.

30.8(b)/Providing and fixing jet spray with 2'-6" long PVC pipe with PTMT nut

30.64(c)/Providing & Fixing in position C.P. Brass Hexa Nipple 15 mm of approved make (to the approval of Engineer-in-charge) complete in all respect.

30.16/Providing and fixing in position vitreous Chinaware white large flat back or angular lipped front urinal 610 mm high of approved make (to the approval of the Engineer-in-charge) (610 mm x 410 mm x 380 mm) consisting of C.P. waste 32 mm dia and C.P. brass spreader, complete.

30.32(ii)/Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32 mm dia with one C.P. brass pillar tap complete in all respect. Size 550 mm x 400 mm x 815mm.

30.43(i)/Providing and fixing vitreous chinaware standard pedestal of approved make (to the approval of Engineer-in-charge) for wash hand basin complete in all respect.

30.84/Providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

30.47/Providing and fixing in position stainless steel sinks of approved make 1 mm thick, grade-304 (18/8) with waste coupling complete in all respect. (a)/Rectangular Sink with Deluxe Border Single Bowl Overall Size 700 mm x 555 mm x 230 mm

30.72(e)/Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge) complete in all respect - PVC tube connection of size 15 mm x 375 mm with PTMT nut

30.20/Providing and fixing PVC waste pipe 32 mm i/d of approved make (to the approval of Engineer-in-charge) complete in all respect.

30.65(A)/Providing & Fixing in position 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge) complete in all respect. (i)/C.P. brass Bib cock long nose/ long body without flange

(ii)/C.P. brass Bib cock without flange

30.66/Providing & Fixing in position stop cock / Angle valve of approved make (to the approval of Engineer-in-charge) complete in all respect. (c)/C.P. Brass 15 mm Angle valve without flange

(b)/C.P. Brass 15 mm Concealed stop cock with flange.

30.64(A)/Providing & Fixing in position C.P. Brass flange of approved make (to the approval of Engineer-in-charge) under various fixtures complete in all respect.

30.64(B)(i)/Providing & Fixing in position C.P. Brass extension piece 25 mm long to 50 mm long of approved make (to the approval of Engineer-in-charge) with various fixtures complete in all respect.

30.61(a)/Providing & Fixing in position 5 mm thick bevelled edge mirror of superior glass (of approved make) complete with 4 mm thick hard board backing fixed in with rawl plugs 50 mm , C.P. brass screws and washers complete in all respect (as required by the Engineer-in- Charge) - Size 600 mm x 450 mm.

30.69(B)/Providing and fixing in position premium range C.P. Brass Fittings and accessories of approved make (to the approval of Engineer-in-charge) complete in all respect. (Note:-To be provided only for VIP Installations and with prior approval of the Engineer-in-charge.) (iv)/C.P. brass toilet paper holder with flap.

30.63(a)/Providing & Fixing in position C.P./ Aluminium Khunti of approved make (to the approval of Engineer-in-charge) fixed into wall with C.P. brass screws and rawl plugs etc. complete in all respect - C.P. Brass khunti with 3 pegs

30.100/Providing and fixing in position vitreous Chinaware white channel of approved make (to the approval of Engineer-in-charge) of size 600 mm x 100 mm including laying and fixing in cement concrete 1:2:4 complete in all respect.

30.97(A)(ii)/Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer -in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and base support for tank - Double Layer Tanks (a)/1000 Litres capacity

(c)/500 Litres capacity

30.96(B)/Providing and fixing in position automatic brass Ball Cock in tanks. (iii)/Brass Ball Cock with rod and Plastic Ball.25 mm i/d

30.98/Providing and fixing in position G.I. Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC Water storage tanks complete in all respect. (c)/G.I. tank nipple 25 mm i/d

NS/Construction of Platform for placing PVC Water Storage Tank with Brick Ballast Work, Plaster, CC 1:8:16, CC 1:2:4, cement rendering etc. of required size complete in all respect.

Sub Head-4 : Flooring and Wall Tiles

14.3/Base course of floor consisting of 100 mm thick cement concrete 1:8:16 with stone aggreate and 100 mm sand filling.(using mechanical mixer for mixing of material)

14.123/Providing and laying Rectified Porcelain floor tiles 400 x 400 mm or more (thickness to be specified by the manufacturer) of premium quality conforming to IS:15622 of approved make in all colours laid on 20 mm thick bed of Cement Mortar 1:4 (1 Cement : 4 Fine sand) for new flooring complete Rectified tiles have finished edges allowing them to be placed closer together for a narrower grout joint as opposed to other tiles and are more expensive. Unlike typical factory-edged tile, rectified tile is cut to size after the firing process.

14.126/Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 250 x 330 mm as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

14.88/Coloured Granite stone tiles 20 mm thick in skirting, risers of steps dado, walls and pillars laid in 12.5 mm thick cement mortar 1:3 (1 cement, 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing & polishing including labour for fixing dowels, pins and cramps.

SUB WORK-2 : ESTATE WATER SUPPLY

28.2/Excavation by mechanical means(JCB or Hydraulic excavator) in trenches for pipe lines with straight or open cutting in streets or open area including tri mm ing and dressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling consolidation, watering , including the cost of dewatering of rain water, diversion for traffic, night signals. providing & fixing caution boards, crossing over trenches for access to the houses, watching, fencing, etc. and removal of surplus soil out side/inside the town involving lead up to 15 meter complete in all respect. (a)(i)/Earth work up to 1.5 m. Depth for

28.36/Providing and laying, jointing, fixing, testing ISI Marked G.I. Pipe (as per IS 1239) B- Class, premium make such as (Jindal Hisar) including cost of Specials such as tees, bends, sockets elbow etc., cutting, threading and testing in trenches in the ground complete. (f)/50 mm i/d

10.7(b)/Cement Concrete 1:6:12 with 40 mm gauge stone aggregate using concrete mixer (ii)/For Covering G.I. Pipe

28.40/Providing, fixing and jointing G.I Union Couplings (of approved make with the approval of EIC) as per IS 1879 in G.I. Pipe lines complete in all respect. (f)/50 mm i/d G.I. Union

28.43/Providing, fixing and jointing ISI Marked Gun-Metal peet valves (Heavy Pattern) as per IS 778 with hand wheels, on G.I. Pipe lines laid in the ground or inside buildings including all carriages complete. (f)/50 mm i/d Gun Metal peet valve heavy pattern.

28.34/Providing ISI Marked G.M ferrule as per IS:2692, drilling and tapping cast iron pipe lines of all diameters and screwing in Ferrule and connections complete in all respect. (f)/25 mm i/d Ferrule heavy duty

SUB WORK-3 : ESTATE SEWERAGE

29.43/Providing, laying in trenches to correct gradient and alignment and jointing of UPVC pipes having ISI specification IS:15328-2003 class-SN-8 marked make Supreme, Finolex, Kissan, Jain, Prince or equivalent good on them and laying the same in trenches to correct alignment and gradients, cutting and jointing, testing for water tightness and making good the leakages and defects including cost of specials (Specials and Solvent should be of same make as that of pipes) complete in all respects. (a)/110 mm o/d pipes (For Sewer line GT to IC - 6 Mtr. each 110 mm)

(b)/160 mm o/d pipes (For Sewer Line)

29.2/Earth work in excavation for storage and sedimentation tanks, high level tanks, filter beds, clear water reservoirs, pump houses, sumps, screening chambers and other similar works having straight or open cuttings in foundations trenches etc. with 3D Excavator/ JCB including manually dressing of bed, trimming of sides and side slopes to full dimension and depth as shown on the drawings or as shall be required by Engineer-in-charge,

10.6(b)(ii)/Cement Concrete 1:8:16 with 40mm gauge stone aggrigate

11.6/1st Classs burnt brick work laid in cement sand mortar 1:5

14.10/Conglomerate floor 50mmm thick CC 1:2:4 on 100 mm 1:8:16 and 100mm sand or stone filling

15.45/12.5mm thick cement plaster 1:4 under side of lining

29.34 A (c)/Providing & fixing 560 mm, 500 mm and 450 mm internal diametre circular or 450 mm x 600 mm clear inside opening rectangular RCC manhole cover and frame ISI marked as per IS:12592-2002 including carriage from the stores of the Engineer-in-charge to site of work, loading, unloading including stacking and setting the same to correct lines over manholes including cement concrete copping (M:20) around the frame etc. Dia of steel for lifting hook is 16mm. (for EHD and HD). RCC Manhole cover with Frame 560mm i/d RCC manhole cover with frame as per ISI.

29.35/Foot Rest for Manhole: Providing orange colour safety footrest of minimum 6mm thick plastic encapsulated as per IS:10910 on 12mm dia steel bar confirming to IS: 1786 having minimum cross section as 23mm x 25mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protruded legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specification and having manufacturer's permanent identification mark to be visible even after fixing, including fixing in manholes with 230x150x75cm cement concrete block 1:2:4 (1 cement: 2 sand: 4 stone aggregate) complete as per design.

NS/Provision for Providing and Fixing UPVC SN-8 SW Tee 100 mm i/d

NS/Fixing UPVC pipe Inlet and Outlet connections in Pit Walls and Inside the septic tank 110 mm o/d

29.5(b)(i)/Excavation in trenches with straight or open cutting in streets, lanes or in open area with 3D/JCB or excavator including manually dressing bed, tri mm ing sides and side slopes for sewers and manholes to full depths as shown in drawings, including, dressing to correct sections and dewatering, provision for diversion for traffic, protection of existing services i.e. telephone cables, electric lines, water supply lines and gas lines etc. night signals, profiles, pegs, sight rails, boning rods, watching, etc., fixing and maintenance of caution boards, fencing, refilling trenches, watering, ra mm ing and restoration of surface to original level and removal of surplus spoil from the site of works, up to one chain (15 m) complete in all respects.

10.8(b)(ii)/Cement Concrete 1:6:12 with 40 mm gauge stone aggregate using concrete mixer.

29.48(A)/Making soak pit 2.5m outer Diametre 3.00 metre deep 230mm thick 1:5 brick work honey comb with bricks of 1st class and S.W. drain pipe 100mm diameter, 1.8m long complete as per standard design.

33.02/RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (i) b Wiring fan point (Without fan box)

(ii)/Wiring light point

(iii)/Wiring call-bell point

(iv)/Wiring 6 Amp. wall socket point

(v)/Wiring 6 Amp. Plug control comprising wall socket point

(vi)/Wiring 16/20 amp. power plug control point.

34.01(xi)/Wiring TV sockets and Telephone socket points in powder coated/anodized concealed metal boxes recessed in wall required for suitable number of modules, for having TV sockets, Telephone sockets RJ11 & RJ45 (one module) etc., and covered with Frame Plate etc., & including the cost of required number of modular TV sockets, Telephone sockets RJ11 & RJ45 (one module) and other petty material etc. including the cost of cutting and filling up of chases:- (b) Wiring Telephone socket point RJ11 (one module)

34.12/PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC pipes & HDPE pipes (fire retardant) for wiring purposes including bends, inspection boxes etc., where necessary including other petty material as per PWD General Specifications 2010:- Make:- Diplast/Canon/ AKG/ Poly India/ Polycab/ Ravindra/ Supreme. (ix)/Heavy gauge PVC conduit pipe 20mm dia. (ISI marked 2 mm thick) Flushed

(x)/Heavy gauge PVC conduit pipe 25mm dia. (ISI marked 2 mm thick) Flushed

(xii)/Heavy gauge PVC conduit pipe 40mm dia. (ISI marked 2 mm thick) Flushed

(xxv)(d)/ Supply and erection of PVC flexible pipe complete with compression glands, having locking arrangement, check-nuts as required :- PVC flexible pipe 40mm dia.

34.11(vi)/HEAVY GUAGE WELDED CONDUIT PIPES: Supply & erection of Heavy guage welded conduit pipe (ISI marked) as per IS:9537:Part-II for wiring purposes including bends, junction boxes, Steel hooks, GI saddle clamps and other petty materials etc., where necessary including painting as per PWD General Specifications:- (vi) HGW Conduit PIpe 20mm dia (1.6mm thick) Flushed).

34.09/PVC INSULATED SINGLE CORE FRLS COPPER CONDUCTOR CABLE: Supply and erection of PVC insulated single core FRLS copper conductor cable ISI marked left bare in pipe or casing of suitable size excluding the cost of supply and erection of pipe or casing. Make:-Finolex/Polycab/ RR Kabel/ Havells/KEI

(ii)/ Overall size 1.5sq.mm (Un-sheathed)

(iii)/ Overall size 2.5sq.mm (Un-sheathed)

(iv)/ Overall size 4sq.mm (Un-sheathed)

(vi)/ Overall size 10sq.mm (Un-sheathed)

33.14(vi)/Fixing additional Length of earthing with 8 S.W.G. (4mm dia.) copper wire in G.I. pipe with sockets, elbows, steel hooks and GI saddle clamps including painting etc.:- (a)Additional Length copper wire 8 S.W.G. (4mm dia.) in 20mm dia. G.I. pipe (On Surface)

33.14(vi)(b)/Supply and Erection of 8 SWG 4mm dia copper wire run through 20mm dia. Heavy guage welded conduit pipe (As additional length).

33.21(B)/Supply and erection of Switch Disconnector Fuse Unit with HRC Fuses (Suitable for DIN HRC Fuses) in sheet enclosure on the existing surface Confirms to IS 13947 (Part-III), IEC 60947- 3 complete with G.I. Bolts, Nuts & Connections on both sides of switch with suitable size of thimbles, including cost of DIN HRC fuses as per PWD General Specifications:- (i)/SDF TP&N 32Amp., 415volts (With Sheet Enclosure)

33.17/SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB/ RCBO/ RCCB's: Supply and erection of sheet metal Double Door Distribution Boards IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, color coded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the distribution board (For SP&N distribution board with provision DP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:- (ii)/SP&N Double Door Distribution Board 8 way each

33.16A/MINIATURE CIRCUIT BREAKERS/ RCBO's/ RCCB's: Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:- (ii) MCB Single Pole 6-32amp. (10kA, Curve-C)

(xiv) MCB Four Pole 6-32amp. (10kA, Curve-C)

33.37(A)/DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES: Supply and erection of double walled corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation (making necessary trench), placing the pipe in position and back filling with excavated soil etc. of the required size. Make : Duraline / Emtel (ii)/Double walled corrugated (DWC) HDPE pipe 63/ 51mm (outer/ inner dia.)

NS/Supply and erection of High quality aluminium extruded with decorative end caps glazed LED batten of Make Jaguar Item Code LGLZ01x020XC or Its equilant Make and Cat. of Philips / Wipro including erection of the same with connections, testing etc.complete in all respects as approved and desired by the Engineer in-charge at site.

NS/S/E of Energy Saving Fan Ceiling Fans 1200 mm sweep ( 48" ) having two ball bearing but without regulator including flexible wire & petty material etc. for connections complete with erection, connections and testing etc. complete in all respect as approved and desired by the Engineer-in-charge at site. Make :- Crompton Entrust 50-5 Star or its equillant make Havells ES-50 Premium 5 Star /Orient.

NS/Supply and erection of 12" Heavy Duty Exhaust fan (HDEF) (300mm-900RPM) Single Phase of make Crompton Model EXHD 300-6-1 or Its equialant Make Havell's Turbo Force SP / GE 151 marked heavy duty motor with die cast Aluminium rotor mounted on two ball bearing including erection, connections and testing etc. complete with flexible wire and petty material reqd. for connections and louver shutter complete in all respectsas appd. and desired by the Engineer in-charge at site

NS/Supply and erection of Plastic Ventialtion Fan Ventilus 10" (250 mm - 900 RPM) single Phase of make Crompton , White Colour or Its equialant Make Havell's / GE including erection, connections and testing etc. complete with flexible wire and petty material regd. for connections and louver shutter complete in all respects as approved and desired by the Engineer in-charge at site

NS/Supply and erection of Wall fan of 400mm sweep (16") High Speed. Make Crompton WM Fizzair Opel White or Its equilant make Havell's / Orient ISI marked heavy duty motor with die cast Aluminium rotor mounted on two ball bearing including erection, connections and testing etc. complete with flexible wire and petty material reqd. for connections and Aluminium louver shutter complete in all respects as appd. and desired by the Engineer in-charge at site.

NS/Supply and erection of Glazed LED Batten Hgh Qualty Aluminium Extruded with decorative end caps of Make Jaguar Item Code LGLZ01X0410XC or Its equilant Make and Cat. of Philips / Wipro including erection of the same with connections, testing etc.complete in all respects as approved and desired by the Engineer In-charge at site.

NS/Supply & erection of Computer Terminal suitable for Computer Networking with modular accessories one on. metal box 12 module 8" x 6", 3 Nos. Switch 6 Amp, 3 Nos. Socket 3 pin 16 Amp, 1 No. Switch 20 Amp, 1 Nos. Socket 20 Amp and 1 No. Modular Accessories including connections & testing complete in all respect as desired by the Engineer-In-Charge at site.

33.10(D)/XLPE INSULATED UN-ARMOURED CABLES (LOOSE): Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:- (xxii)Overall size 25sq.mm (3½ Core) Un armoured (Loose)

NS/Supply & Erection of LED Street Light 45w in aluminium pressure Die Cast housing with touched glass cover (IP 66 protection ) of Make Jaguar Item Code LSR T 0150 4SxC or its equilant make and connections and testing etc. complete in all respects as aproved by the Engineer in charge at site.

33.29(B)(i)/SINGLE ARM BRACKETS FOR GI PIPE POLE: Supply and erection of G.I. Pipe 40mm dia. (A-class) Single arm bracket of suitable length give a total overhang at a tentative angle of 100/105º, the bracket should be fixed on the top of the GI pipe pole having top outer dia. 80mm/100mm with GI reducer of suitable size with two coats of an approved aluminium paint complete in all respect as approved by the Engineer-in-charge at site:- (a) Single Arm Bracket 1 metre Long with G.I. Reducer 80mm x 40mm

33.15/SUPPLY AND ERECTION OF WIRING ACCESSORIES: Supply and erection of switches, sockets and other accessories (flush piano type/ modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc.,:- (xxvii)Bakelite Batten Holder (Large size)