SPL REPAIRS BLDG TO BLDG NO P 32 AT SELECTION CENTRE SOUTH BANGALORE PROVN OF SECURITY FENCING FOR NFS NODE AT CUBBON ROAD AND OTHER SANCTIONED WORKS UNDER GE SOUTH BANGALORE

Amount

Dismantling of existing roof treatment and removing outside MD land complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) in padding concrete for roof treatment complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished the surface fair and even mixed with WPC complete all as specified and directed. Note:- WPC shall be measured and paid separately under relevant Item of this Schedule.

Supply only integral water proofing compound ISI Marked of approved make complete all as specified and directed.

Material and labour for cleaning the plastered/concrete surfaces with wire brushes and applying water proofing treatment as under :- (a) Apply one coat of bituminous primer @ 0.25 kg/sqm. (b) One coat of Hot applied bitumen 85/25 grade at the rate of 1.2Kg (minimum) per sqm on priming surfaces (c) Laying APP polymer modified membrane granular finish on top layer of weight not less than 3.8 to 4.0 kg per sqm by torch application method including a coat of solar reflective aluminium paint @ 0.25 kg/sqm complete all as specified and directed.

Dismantling PVC/CI/AC drain pipe n.exc 110 mm dia complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of oil emulsion distemper over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparing old treated surfaces of walls and applying two coats of acrylic (antifungal) exterior grade paint over a coat of primer complete all as specified and as directed.

M&L for rendering 5mm thick on concrete surfaces of ceiling in cement mortar 1:3 finished even and smooth without using extra cement including taking down the existing plastering complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of oil emulsion distemper over a coat of alkali resistant primer complete all as specified and as directed.

Surface excavation not exc 30 cm deep and avergaing 15 cm deep and getting out in hard/dense soil complete all as specified and directed.

Excavation in post holes (for similar holes) each n.exc 0.5 cum getting out, returning filling in and ramming earth or broken rubbed mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n exc 50 m and making good surface in hard/dense soil complete all as specified and directed.

Removing excavted materials exc 500 m and n. exc. 1000 m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

M&L for 100 mm thick cement concrete type D-2 1:4:8 (using 40 mm graded stone aggregate) as in sub base of floors complete all as specified and directed.

M&L for 100 mm thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) finishing the cement concrete surface even and fair as in hard standing complete all as specified and directed.

S&F steel work in tubular trusses and tubular posts including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1998 grade St.-240 incl one shop coat of zinc chromate primer paint complete all as specified and directed.

S&F steel work in rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc conforming to Fe 410-W (Gde-E- 250) quality-A incl one shop coat of zinc chromate primer paint complete all as specified and directed.

S&F 0.50 mm thick pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet of an having.colour on exterior side tensile strength of 550MPA as in roof covering/cladding to walls fied with self tapping screws as specied and conforming to all as specified and directed.

M&L preparation of new or previously untreated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enemel paint over a coat of red oxide primer complete all as specified and directed.

M&L for 100 mm thick PCC 1:3:6 type C2 (using 40 mm graded crushed stone aggregate) complete all as specified and directed.

S&F machine pressed rubber moulded precast cement concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 grade with grey cement and no pigment laid over and including 50 mm thick consolidated sand cushioning complete all as specified and as directed. Note : The gap between kerb stone & paver block to be filled by cement mortar and finish to match the shade of interlocking paver block as directed.

M&L for providing cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in roof kerb or mud stops, rounded or chamfered complete all as specified and directed.

Roughning surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0 Kg of cement per sqm complete all as specified and directed.

S&F dark shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.24 sqm and not exceeding 0.36 sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 20 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

S&F dark shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.24 sqm and not exceeding 0.36 sqm as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

Excavation in post holes (for similar holes) each n.exc 0.5 cum getting out, returning filling in and ramming earth or broken rubbed mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n exc 50 m and making good surface in soft/loose soil complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) in wall or retaining wall, any thickness, size r shape incl pilasters, buttresses columns, pillars, boundary pillars and posts (incl caps and bases) complete all as specified and directed.

S&F mild steel works conforming to Fe 290 Gde E-165 as in angle iron post and struts in fencing incl cutting tops to shape as directed drilling holes notching for wire etc. incl all necessary drilling, bolting of riveting etc complete all as specified and directed.

Fixing only chain link fencing incl line wires, any mesh, size and type to any type of standard rails, straining bolts, etc incl provision of binding wire complete all as specified and directed.

Supply only MS galvanised chain link fencing any size or type complete as sample approved by GE.

S&F galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails incl securing or tying at crossing with and provision of galvanised mild steel wire complete all as specified and directed.

S&F concertina coil of 450mm dia, made out of 2.5mm dia spring wire 230 gm/ sqm (min) dipped with corrosion preventive fluid (rusilo 901) of castrol make in white colour each coil having a minimum 40 tuns (circles) and an average weight not less than _Kg/(plus or minus 5%) razor length minimum 10mmm and spacing between razors max 25mm centre to centre including handle and spike at both ends of coil (length of each coil 5 to 5.5M) errected in position on top of mild steel angles MS rod for securing incl necessary welding to the MS sections etc. fixing with cold rolled carbon strip of thickness 0.45 mm, width of tape 12 to 15 mm complete all as specified and directed. Note: Measurement shall be made for length of fencing (flat measurement) only

Excavation in trenches, n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc or for shafts, wells cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

M&L for cement concrete 1:4;8 type D2 using (40 mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete M-25 design mix (using 20 mm graded stone aggregate) as in foundation, incl rafts, footings, foundation beams, plinth beams, bases for columns etc, basement slabs under reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete M-25 design mix (using 20 mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for reinforced cement concrete M-25 design mix (using 20 mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

S&F mild steel TMT bars 10 mm dia and over cut to length, bent to shape required incl cranking, bending, spirally for hopping for columns, hooking ends and binding with and incl mild steel wire not less than 0.9 mm dia or securing with clips quality conforming complete all as specified and directed.

S&F mild steel TMT bars 6 to 8 mm dia cut to length, bent to shape required incl cranking, bending, spirally for hopping for columns, hooking ends and binding with and incl mild steel wire not less than 0.9 mm dia or securing with clips quality conforming complete all as specified and directed.

M&L for rough finished formwork to sides of flat concrete foundations, footings, based of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions etc complete all as specified and directed.

M&L for formwork to edges of concrete flats, breaksin floors, openings in concrete wals, floors and roofs and sides of RCC/PCC bands in walls, horizontal of slopping, and similar work complete all as specified and directed.

M&L for precast cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in block masonry with solid blocks, exc 10 cm in width and setting in mortar complete 1:4 complete all as specified and directed.

All as Item no. 45 here-in-before except blocks or slabs set in cement mortor 1:4 complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 incl finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for preparation of newly plastered surface and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering & well ramming in layers n exc 25 cm complete all as specified and directed.

Removing excavated material (Soil) n exc. 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles incl removing debrits out side the MD land complete all as specified and directed.

M&L for providing cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) in lintel upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, stringcourses lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones bed plates,kerbs incl weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

S&F coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match over 20 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surface 300x200x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

M&L for precast cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in block masonry with solid blocks, exc 10 cm in width and setting in mortar complete 1:6 complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and rough (without using extra cement) complete all as specified and directed.

M&L for 75 mm thick, PCC 1:3:6 type C1 (using 20mm graded stone aggregate), finished even and smooth without using extra cement.as in plinth protection incl joints filling complete all as specified and directed.

M&L preparation of newly plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and directed.

S&F factory made solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, complete all as specified and shown in drawings complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, fixed in the frame at site as specified and directed at site complete all as specified and directed.

S&F 100mm butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips or sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium ally fixed complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolts and extrude section and fixed.

S&F 125 mm long extruded aluminium alloy handles, fabricated type anodised

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 Kg/m incl necessary joining cleats, glazing clips, rubber packing, anodised aluminium spap beading, screws etc, complete all as specified and directed.

S&F 4.0 mm thick figured glass, pin head type and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

M&L for providing precast cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier, caps, columns, pillars, bed plates, pintle blocks, anchorage blocks, bounder (for stone walling), setting in cement mortar 1:4 complete all as specified and directed.

S&F steel windows with side hung shutters incl projecting type hinges with steel handle and steel ped stay, complete with glazing bars dovetailed or welded complete all as specified and directed.

S&F 4.0 mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tacks, or galvanised wire staples etc complete all as specified and directed.

S&F GI pipe 15 mm dia medium grade steel water tubing with fittings fixed on walls or laid in floor concealed type complete all as specified and directed.

S&F 75mm size PVC floor trap with grating incl jointing with solvent cement complete all as specified and directed.

S&F vitreous china wash down water closet pan & trap (pedestal pattern) with plastic water closet seat black closet pattern with flat bottom and cover and mild steel chromium plated or aluminium hinginng device with flush pipe to pedestal pan incl all joints incl connection to drain pipe and flush pipe complete all as specified and directed.

S&F PVC flushing cistern low level of 10 ltr capacity white with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F vitreous china wash hand basin 630x450mm and waste pipe waste coupling etc but incl brackets complete all as specified and directed.

S&F 15 mm bore pillar taps, cast copper alloy, fancy type with capstan heads, chromium plated screwed down high pressure with or without lattered 'Hot' or 'Cold' with long screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 15 mm bore fancy type two way bib taps, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 125x100 mm size gully traps square or rounded mouthed type complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing servicieable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in floors finishing complete all as specified and directed.

Disconnecting existing tanks of capacity exc 500 ltr and n.exc 1000 ltr tanks, setting aside (or lowering if required) for repairs, cleaning etc, and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

S&F GI pipe 20 mm dia medium grade steel water tubing with fittings fixed on walls or laid in floor complete all as specified and directed.

M&L for granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone incl grinding and polishing complete all as specified and directed.

S&F in repair PVC flushing cistern low level of 10 ltr capacity white with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair soap dish vitrious china white, approximate size 160x160x90 mm fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F health faucet with PVC tube 1m long with screwed nut for inlet connection & making good surface of wall tiles complete all as specified and directed.

S&F 32 mm bore waste fittings, brass, chromium plated for glazed ware basins with long screwed shanks and fly-nuts, flange end bedded red lead cement and other end fixed complete all as specified and directed.

S&F PVC connection 15 mm dia with PTMT nuts of lenth 450 mm complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail 20 mm dia, D type 60 cm long between flanges complete all as specified and directed.

S&F kitchen sinks with drainage board out of Stainless steel 1.00mm thick with plugs, washers and waste pipes and cast iron cantilever brakets including and connecting union to pipe over all size 915mm X 460mm bowl size 410mm X 330mm X 160mm complete all as specified and directed.

M&L for 18 mm thick veneered decorative plywood,grade 1(with BWR resin) with decorative face veeners on one side fixed with screws to timber frame work & another side painted with 2 coats of synthetic enamel paint fixed with screws to timber frame work complete all as specified and directed.

Extra over item of block board or veneered particle board for external teak wood lipping, 6mm thick, fixed with nails complete all as specified and directed.

S&F 30 mm wide continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F MS 40mm dia, cupboard knobs fixed with nut, screw and washer of brass polished, bright finished complete all as specified and directed.

S&F magnetic catch for drawer of suitable size complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls and applying one coat of distemper oil emulsion complete all as specified and directed.

M&L for point wiring surface type with single core 1.5 Sqmm PVC insulated unsheathed single core multistranded copper conductor cable (FRLS)including 1.5 Sqmm PVC insulated unsheathed copper conductor as earth continuity conductor drawn in and including ISI marked PVC casing caping not less than 20mm width with its accessories, and fixed in existing sunk boxes and covered with new 3.00 mm thick ISI marked laminated sheet cover and brass screw with cup washers for fixing switches/sockets/regulators etc.one light/CB/fan point controlled by one switch complete all as specified and as directed.

All as per item No. 102 here-in-before but for one 3 pin 5 Amps socket point on the same board with other switches all as specified and as directed.

All as per item No. 102 here-in-before but for one 3 pin 5 Amps socket point on the independent board with other switches complte all as specified and as directed.

All as per item No 102 here-in-before but with cable 4.00 sqmm including 4.00 sqmm cable as earth wire for 15/16 amp socket on independent board complte all as specified and as directed.

All as per item No 102 here-in-before but with cable 2.5 sqmm including 2.5 sqmm cable as earth wire for 15/16 amp socket on independent board complte all as specified and as directed.

S&F switch piano type, 5 Amps single pole one way complte all as specified and as directed.

S&F switch socket combination 2 in 1, 3 pin 5 Amps flush type universal complte all as specified and as directed.

S&F switch socket combination 3 pin 5 Amps and 15 Amps flush type complte all as specified and as directed.

S&F ceiling rose surface bakelite 65x50 mm two to three terminals complte all as specified and as directed.

S&F lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings/angle fittings complte all as specified and as directed.

S&F 9 W LED LAMP system lumen (NOM)850 with cool day light CCT 65000K retrofit with base B-22 complte all as specified and as directed. Make:- Bajaj cat part No- 9W-CDL B22 or equivalent in CG/Philips

S&F exhaust fan PVC complete with accessories 230 Volt, 250mm sweep including fixing accessories complete all as specified and directed. Make :- Bajaj MAXIMA DX Product code 70049 or equivalent in Crompton/ Havells

S&F LED batten 18 watt, 4 feet long suitable for indoor applications with integrated electronic driver of operating voltage 110 to 270 Volts , Lumin output not less than 1800 lm including connecting up and taking down existing unserviceable surface/ ceiling mounted 28/36 watt FTL fitting complete all as specified and as diretcted Make:- Bajaj Cat No. BCLSBAL18W CW/Crompton Cat No LCTL-18-CDL or equivalent in C&S.

S&F wall mounted fan with accessories, 400mm sweep single phase, 230 Volt BEE 5 star rated, ISI standards, RPM 1320, Air Delivery 70CMM and pre-wired and including connecting up with twin core twisted flexible copper conductor cable with connector complete all as specified and as directed. Make :- Bajaj Esteem wall fan Product code 250542 or equivalent in Crompton/ Havells

S&F MCB, DB double door type, made out of CRCA mild steel sheet flushed in wall, SPN 8 way with 200 Amps rated bus bar , 240 volts IP-43, with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and as directed. Make: Indoasian Cat No: 811807 or equivalent in Havells/Legrand/Standard.

S&F MCB SPN 6 -32 Amps, 240 Volts 50 Hz, 10 KA rating "C' Curve complete all as specified and as directed. Make: Indoasian Cat No: 811144 to 811151/ Legrand Cat No 408609 to 408617/ Schneider Cat No A9N2P06C to A9N2P32C

S&F MCB SP 06-32 Amp, AC, 240 volts, 50 Hz, 10 KA rating "C' Curve complete all as specified and as directed. Make: Indoasian Cat No: 811122 to 811129/Legrand Cat No 408587 to 408595/ Schneider Cat No A9N1P06C to A9N1P32C

S&F stepped type electronic fan regulator modular type, 230V AC all as specified and as directed.

S&F bell push, flush type 5 Amps single pole, one way, 230 volts all as specified and as directed.

S&F call bell 5 Amps single pole, one way,230 volts all as specified and as directed.

M&L sub main wiring surface type with two runs of single core, PVC insulated, unsheathed multi stranded copper conductor cable of size 6 Sqmm, 1100 volts grade (FRLS) and one run of 6 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through PVC casing and caping incl taking down old one complete all as specified and as directed. (Note :- Two runs of 6 Sqmm cable, one run of 6 Sqmm continuity earth wire and one run of PVC casing and caping with all necessary accessories will be measured as one length).

S&F MCB, DB double door type, made out of CRCA mild steel sheet flushed in wall, SPN 4 way with 200 Amps rated bus bar , 240 volts IP-43, with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and as directed. Make: Indoasian Cat No: 811805 or equivalent in Havells/Legrand/Standard.

Elite Constructions