Loading…
Loading…
Tender Value
Refer Docs
EMD Value
₹7.5 L
Closing Date
1 Jul 2026, 3:00 pm
Signalling work in connection with provision of second goods shed common running line of 750M at Phariya station of BSB division.
NER-BSB0SnT-OT-27-2026
NER-BSB0SnT-OT-27-2026
Open
12 Months
Unknown (Unspecified Location)
₹0
₹7.5 L
6 Jun 2026
6 Jun 2026
17 Jun 2026
B- Telecommunication
Trenching upto depth of 1.20 Mtr & 30Cm wide base in all type of soil, backfilling after laying of OFC cable at1.20 Mtr depth. Ramming &consolidation of soil in trenches as well as disposal of soil if any. This includes all preventive 1 works (& all material supplied by contractor), if required. Note:-(a) Payment will be made as per actual work done on Pro-Rata basis if required depth is not available at site. (b) :- If the depth of Trench is not uniform in a span of 100Mtr or shorter lengths, if site condition demands along the cable run, minimum depth will be taken for that particular stretch for Payment as per technical specification attached.
Horizontal direction drilling (HDD)/Trenchless digging/machine drilling without damage to surface road /track for laying/insertion of DWC/GI/HDPE pipe. The bore shall be done of min. diameter 120mm & at the depth of minimum 1400 mm 2 from the ground level. The ground level shall be considered ignoring the bank height of the bank of the road/ track. Note:- DWC/HDPE/GI Pipe supply is not covered under this item. Contactor shall provide all material required for work and adequate nos. of labours for proper laying of cables into the bore. Cables shall be laid cautiously so that these should not get damage due to rough handling & pressure on cable. Payment of boring shall be made only after laying of DWC/HDPE/GI pipe in the bore as per technical specification attached..
Trenching on pucca road/Platform upto depth of 1.20 mtr. & 30 cm. wide and refilling with soil including 3 levelling of trenches and repairing to the original condition . The responsibility of obtaining permission from civil authorities, like -Municipality. PWD, Forest etc. rest with tenderer as per technical specification attached.(All the materials required for repairing of road / platform shall be supplied by the contractor)
Blowing/drawing of OFC cable in the HDPE duct and in protective works(already provided) as per technical specification attached..
Laying of HDPE duct (of size 40/33mm outer dia/inner dia) in the trenches & in protective works, already provided ,including in HDD portion and supply , pulling of nylon rope through it, at different places, as per direction of engineer incharge or site engineer as per technical specification attached.. (HDPE pipe with couplers shall be supplied by Railway)
Supply, Installation, testing and commissioning of 48 Fiber (SC/APC-SC/APC) FDMS as per RDSO/SPN/TC/037- 2000 Rev.3, Amdt. 2 or latest. Inspection: Consignee.
Fabrication, Supply and Fixing of Cable Route Marker of 1:2:3 Concrete as per DRG No-CST/OL. S .K. No. NER/GKP/SK/CM/2017Dt.29-05-2017. The marker shall be fixed at various places of cable route as per instruction of site engineer as per technical specification attached.
Supply of 15U Rack Enclosures Networking/Server Rack Brand: PANSIM (Detailed Description/Specification as per technical specification attached, inspection-Consignee.
Supply of OFC patch cord with SC-LC, LC-SC 10 meter long as per tech spec attached, inspection :Consignee Unit Above/
A 1- ELECTRONICS INTERLOCKING with 01 Additional Goomty
Supply of materials Required for Alteration of Existing EI along with all interfacing relays along with one additional goomty, Inspection-RDSO.
Alteration of Existing Application Logic Programme to suit Modified SIP
Alteration to existing interface circuit diagram to suit Modified SIP.
Factory Acceptance Test of EI System.
Site Acceptance Test of EI System
Installation, Testing & Commissioning of EI System as per Modified SIP Unit Above/
A 2- Outdoor Signalling works
Supply of and Fixing of MS Flat size 32 mm x 5 mm as Earth lead on location boxes and interlocked LC gate of BSB division. All required materials will be supply by the contractor as per the technical specification attached, Inspection- Consignee.
Earthing of CT Rack, Relay Rack, DG sets etc. including supply of Earthing materials as per the technical specification attached, Inspection-Consignee.
Supply of ARA Terminal 1 Way 60 mm asper RDSO Drg. No. SA - 23745 Alt - 5 and Specification No. IRS: S: 75/2006 with latest amendment if any. Inspection: RDSO
Supply of ARA terminal 6 way as per the technical specification attached, Inspection-RDSO.
Supply of Bus bar 50 way as per the technical specification attached, Inspection-Consignee.
SUPPLY OF Non Metallic ARM TYPE JUNCTION ROUTE INDICATOR COMPLETE WITHOUT LENSES AND LIGHT UNIT 8 2/3/4/5 WAY (as demanded by Consignee) SUITABLE FOR LED SIGNAL UNITS as per RDSO/SPN/194/2006 rev. or latest IRS:S:66/84 & RDSO DRG. NO. 23403 ( ADV.) 4 WITH LATEST AMENDMENT IF ANY & as per technical specification attached, inspection-Consignee.
Supply of Elbow for Home Signal 5.5" as per RDSO Drg no. SA 23080 (ad) with latest amendment as per the technical specification attached, Inspection-Consignee.
Supply of C.I. Tubular base for CLS as per the technical specification attached, Inspection-Consignee.
Supply of C.I. Tubular base for Shunt Signal as per the technical specification attached, Inspection-Consignee.
Supply of CLS Post of 4.6 M as per the technical specification attached, Inspection-Consignee.
Supply of Non metallic CLS unit 2 Aspect as per Drg No. 23003 A/M ( Adv ) but without lamp, lenses, holder and signal transformer as per RDSO/SPN/194/2006 rev. or latest, Inspection-Consignee.
Supply of Non metallic CLS unit 3 Aspect as per Drg No. 23002 A/M (Adv) but without lamp, lenses, holder and signal transformer suitable for LED signal.as per RDSO/SPN/194/2006 rev. or latest, Inspection-Consignee.
Supply of Ladder for CLS of 4.6 Mtr post as per the technical specification attached, Inspection-Consignee.
Supply of Calling on signal unit without lenses and lamps and offset bracket 3.5" dia with out signal transformer as per RDSO Drg no. SA 24351 Adv Alt -1 as per the technical specification attached, Inspection-Consignee.
Supply of Shunt signal dependent type RDSO Drg no. SA 23840 Adv Alt -2 complete with mounting socket to Drg No. SA 23844 but without lamp and lenses suitable for 140 mm outside dia pipe complete with mounting socket to Drg No. SA 23080 as per the technical specification attached, Inspection-Consignee.
Supply of Shunt signal independent type RDSO Drg No. SA 23840 Adv Alt -2 complete with mounting socket to Drg No. SA 23845 but without lamp lenses suitable for 90 mm outside dia pipe Complete with GI pipe 90 mm dia of 1.5 mts and CI base for post as per the technical specification attached, Inspection-Consignee.
Supply of PVC Wire 16x0.2 sq mm as per the technical specification attached, Inspection-Consignee.
Supply of PVC flexible copper cable single core, multistrand 1x6 Sq.mm (84 conductor each diameter 0.30 +/- 0.01) as per IS 694/2010. with latest amendment if any with insulation thickness of 0.80mm nominal conductor resistance 3.30 ohms/km and test parameters are as per IRS (S) 76/89 (Amd.3), Inspection-Consignee.
Supply of PVC jacketed wire rope for track lead connections. PVC jacketed wire rope should be of Galvanized steel wire rope 6mm dia (6x19 stranded wire with steel core of 6 mm dia) sheathed with PVC 2mm wall thickness, overall thickness being 10 mm. PVC sheath should be made of type 6 compound asper IS 5831 of 1984 Reaffirmed 2001 and steel wire rope as per IS: 2266:2019. Reclaimed for recycled material should not be used, Inspection-Consignee.
Supply of GI Pipe 100 mm dia medium grade ISI mark. Inspection : Consignee
Supply of Eyelet 1.5 mm sq. as per the technical specification attached, Inspection-Consignee.
Supply of Eyelet 4 mm sq. as per the technical specification attached, Inspection-Consignee.
Supply of Low Maintenance Secondary Cell 80 AH as per the technical specification attached, Inspection- Consignee.
Supply of Fuse base for NDT fuse as per the technical specification attached, Inspection-RDSO.
NDT low voltage electric fuse non indicating type fuse as per IRS S:78/92 round edge 14 mm dia, 51 mm length rating 1 Amp, Inspection-RDSO.
NDT low voltage electric fuse non indicating type fuse as per IRS S:78/92 round edge 14 mm dia, 51 mm length rating 2 Amp, Inspection-RDSO.
NDT low voltage electric fuse non indicating type fuse as per IRS S:78/92 round edge 14 mm dia, 51 mm length rating 4 Amp , Inspection-RDSO.
NDT low voltage electric fuse non indicating type fuse as per IRS S:78/92 round edge 14 mm dia, 51 mm length rating 6 Amp, Inspection-RDSO.
NDT low voltage electric fuse non indicating type fuse as per IRS S:78/92 round edge 14 mm dia, 51 mm length rating 10 Amp, Inspection-RDSO.
PPTC ELECTRONIC FUSE X 30 UF 250 30V 2.5AMP. MAKE TYCO FUSE SHOULD BE SUPPLIED IN CYLINDRICAL CARTRIDGE HAVING SIZE 14 MM DIA 54 MM LENGTH OR SIMILAR. INSPECTION-CONSIGNEE.
Supply Of Relay AC immune plug-in type Style QSPA1, DC neutral line slow to pickup 24V, 8F/4B contacts front and back contacts metal to carbon complete with plug-board, retaining clip and connector confirming to BRS:934 A IRS:S@58<44@ IRS:S:23 (as applicable). The interlocking code for this unit shall be ABDEJ, Inspection-RDSO.
Supply of Relay Non Ac Immunize Style QTA2 neutral track 9.0 Ohm 2F/1B contacts front and back contacts metal to carbon complete with plug board, retaining clip and connectors as per spec no. BRS - 938A, Inspection-RDSO.
Supply of Key Lock Checking Relay (KLCR) working on 24V DC, AC Immunized with different ward combinations and contact configuration 4F/4B with 2 extra ward plates and with case, RDSO spec no. RDSO/SPN/219/2016 ver 1.0 or latest, confirming to IRS S-23, S-34 & S@ 45<44@ IRS S:46. Inspection authority- consignee
Supply of Relay plug in type QECX61 ) AC LED all Aspect AC lamp proving relay 4F-4B contacts metal to carbon shall be suitable for working in series with 110 V AC/15 W LED signal, Inspection-RDSO.
Supply of Relay Point contactor AC immunized plug in type DC biased contactor 24V DC with 2HF/4B contacts heavy duty metal to carbon front contacts and back contacts metal to carbon complete with plug board, retaining clip and connectors confirming to BRS : 943 & IRS S: 34 & IRS : S:23. the interlocking code for this unit shall be BCEJK, Inspection-RDSO.
Cable termination racks as per Drg. no. CSTE 5004, 5005, 5006 complete along with fitting arrangements and 38 also with arrangement for fixing four 8-way terminal strips/ Screw less terminals on each row having 16 such rows. Supply of 8 way terminal strips/ Screw less terminals n o t covered under this item. Cable termination rack shall be Powder Coated, Inspection-Consignee.
Supply of choke as per RDSO specification no. IRS: S-65/83 with latest amendment if as per the technical specification attached, Inspection-Consignee.
Supply of PBT BASE Track Feed Adjustable Resistance "DISC TYPE" 15/ 30 ohms as per the technical specification attached, Inspection-Consignee.
Supply of Track Feed Battery Charger as per RDSO Spec. No. IRS: S-89/2013 Rev. 1.0 or latest, Inspection- RDSO.
Supply of track lead junction boxes (4-way) made from fibre glass including ARA terminals, MS angle size 40 x 40 x 6 mm of 1 mtr. length & bent pipes as per RDSO Specification No. RDSO/ SPN/ 151/ 1997 or latest. as per the technical specification attached, Inspection-Consignee.
Supply and fixing of P/G/C markers with complete fittings. All material require for the job such as MS sheet, MS 44 Angle, Nut and bolts, paint & painting materials will be supplied by the contractor as per direction of site engineer as per the technical specification attached, Inspection-Consignee.
Supply & Installation of Number Plate of Signals as per the technical specification attached, Inspection- Consignee.
Supply & Installation of wooden box for CHC size 50x40x15 cm made-up of 19 mm plywood board pasted mica glass as per the technical specification attached, Inspection-Consignee.
Supply of Hand Cuff Lock as per CWM S & T W/S GKC Drg no SW/98/8 as per the technical specification attached, Inspection-Consignee.
Transportation of Materials Including Loading and unloading from consignee's store/ any station to other any station / store as per the technical specification attached.
Supply of Insulated material for ground connection of EPM as per the technical specification attached, Inspection-Consignee.
Installation of Warning board along with supply of warning board.This includes concrete foundation of 600 x 600 x 600 mm as per the technical specification attached, Inspection-Consignee. Note -Rail post will be given by railway at the store of consignee.
Installation, Wiring and Testing of EPM Rotary Type as per tech spec attached.
Fabrication and fixing of bond wire by drilling double hole on each side as per the technical specification attached.
Fabrication and fixing of jumper wire by drilling double hole on each side as per the technical specification attached.
Casting of foundation and installation of Apparatus case SINGLE including supply of all material except Apparatus case and JB as per the technical specification attached.
Casting of foundation and installation of Apparatus case HALF including supply of all material except Apparatus case and JB as per the technical specification attached.
Casting of CLS foundation including supply of concreting materials and foundation bolts as per the technical specification attached.
Erection and fitting and wiring of CLS posts with unit on already casted signal foundation with fixing of Ladder and staging as per the technical specification attached.
Casting of Position type shunt signal including supply of concreting material, erection and fitting of Shunt Signal as per the technical specification attached.
Provision of screen signal when they fall within meters from live conductor by expanding metal size 20mm x 60mm (strand 3.25 mm wide and 1.6 mm thick) as per instruction at site by Engineer In-charge. This includes supply of all materials including earth elctrode and earthing arrangement as per the technical specification attached.
Installation of lever lock DW type fitted with crank Handle /E-type lock /KLCR lock relay assembly and its wiring as per the technical specification attached.
Termination of signalling cable as per the technical specification attached.
Charging of Sec Cell as per the technical specification attached.
Fitting of LED signal with all accessories and its wiring. All material required for fitting and wiring except LED signal and PVC wire shall be supplied by the contractor as per the technical specification attached.
Excavation of cable trench of 110 cm Depth and 30 cm Width in all kind of soils and its refilling with the same excavated soil consolidating by ramming to the level of 20 cm above the ground level over the trench as per the technical specification attached.
Excavation of cable trench of 100 cm Depth and 30 cm Width at level/track crossing and platform and its refilling with the same excavated soil consolidating by ramming to the level of 20 cm above the ground level over the trench as per the technical specification attached.
Horizontal direction drilling/boring without damage of surface road using Auger Machine. The bore shall be 150 mm dia & shall be done at the depth of minimum 1200 mm from the ground level. The ground level shall be considered ignoring the bank height of the bank of the road. The length of the bore shall be minimum 4 Mtrs long. this include insertion of different dia DWC pipe/ GI pipes coupling etc. as per direction of Engineer In charge.
EXCAVATION OF TRENCHLESS TRACKUNDER RAILWAY TRACK/BUSY ROAD ETCAT A DEPTH OF 1.20 METER
Laying of signalling cable (2 core to 12 core) in the trench as per cable route plan approved by railway and meggering of all main & tail cables. The cable laying includes laying of cable in trenches as per the technical specification attached.
Laying of 6 quad Cable in the trench as per cable route plan approved by railway as per the technical specification attached.
Laying of GI / HDPE Pipe for passing the cables at level /track crossing and platform etc. Only GI/HDPE pipe and socket will supplied by railway. Other activity will be done by contractor as per tech. specification.
Installation of Terminal board for terminating main/tail cable including supply of terminal board as per the 74 technical specification attached, Inspection-Consignee. Note -(1). Termination board of hylem sheet IS:2036 grade P-4 size 6mm thick. (2). Angle Iron Size 40mm X 40 mm X 5 mm at station. (3) Angle Iron size 25 mm X 25 mm X 3 mm suit the size of cases i.e. Single case, Half Case, 50 way JB and as for requirments.
Installation & wiring of track feed charger, choke and track battery as per instruction of site engineer as per the technical specification attached.
Preparation of field diagram such as cable Route plan, Power supply lay out, Cable Termination Chart in relay 76 room & Location Boxes, Location Wiring Diagrams, Fuse Analysis, Equipment Disposition Plan, Track Bounding & Insulation Plan as per Railway practice. Note: All the above Diagrams/Plans to be submitted in Polyster Film Tracing to the railway. The contractor shall also supply 6 sets of Photo/Ferro print copy of said plans/drawings out of which 1 set shall be duly laminated as per Tech. specification attached.
Preparation of Station Working Rule (SWR)Including Appendix- A, B , C , D , E , E, Fand G in Hindi and English on Approved SIP/ESP/ST/SWRD/PD/VDU Layout etc. asper the Extant Practice being followed in Lucknow Division of N.E. Railway. 77 The Contractor shall Supply Two Paper Print of the SWR as Draft for Approval and Comments. Once the Approval is given he shall Supply Two Set Paper Prints of the SWR for Final Approval and Signature of the Concerned Officials On obtaining final Approval, The Contractor shall Supply 10Sets of the SWR And 1 Set Gate Working Rule (GWR) of each LC Gate (App.-A) Duly Photocopies of SWR. The Approved SWR shall be Finally Supplied in 2 Pen drives.
Preparation and Printing of Station Working Rule Diagram (SWRD) an Auto Cad based on Approved SIP, ESP etc. 78 as per the extant practice being followed in Lucknow Division of N.E. Railway. Contractor shall Supply One Print of SWRD (Paper Print Size as Required)as Draft for Approval and comments. Once the Approval is given, Contractor shall Supply Tracing of the SWRD on Good Quality Film Paper of Thickness not Less Than 75Micron for Signature of All Officials. On Approval the Contractor shall Supply 10Copies Blue Print of Tracing. The Approved SWRD shall be Finally Supplied in 2 Pen Drives.
Testing and Commissioning of complete yard both indoor and out door including break down testing w.r.t. selection table/locking table using simulation panel, finally from panel in presence of Railway official as per technical specification attached.
Painting of Sigg equipments Signals, Apparatus Cases, EPM etc. of complete Yard including supply of paint as per the technical specification attached.
Cement concrete work for miscellaneous items in the ratio 1:3:6. Item includes excavation, ramming, curing and plastering with cement sand mixture (aggregate not exceeding 3.8cm). Aggregate, cement and to be supplied by contractor as per technical specification attached.
Providing Brick masonary in the ratio 1:6 cement & mortar including plastering with 1;4 cement and sand mixture both sides, 20 mm thick each with contractors own 2nd class brick, including excavation curing grouting bolting etc wherever required. Brick sand & cement to be supplied by the contractor as per technical specification attached.
"Supply of basic material to construct unit maintenance free earth as per RDSO Specs. No RDSO/SPN/197/2008 or latest and conforming to RDSO Drg. No. SDO/ RDSO/E&B/001dtd.19.09.08. It consist of following: (a) Copper bonded steel electrode of 3.0 m long,17.2 mm dia with copper bonding thickness of minimum macrons and UL listed and marked = 1 no.(b) Earth enhancement material supplied in sealed bags of minimum 10 kg = 3 nos. ©Copper strip of 150x25x6 mm, to terminate 83 earth rod = 1 no. (d)Copper strip of 300x25x6 mm(MEEB) = 1 no. (e) Copper strip of 150x25x6mm (SEEB) = 1 no.(ii) Supply of 35 sq. mm multistrand single core PVC insulated copper cable as per IS: 694 for connecting main earth electrode to MEEB in the equipment room induplicate.(minimum 10 meter)(iii) Supply of 16 sq. mm multistrand single core PVC insulated copper cable as per IS: 694 for connecting MEEB to SEEB and SPD to MEEB (minimum 10 meter) (iv) Supply of 10 sq. mm multistrand single core PVC insulated copper cable as per IS: 694 for connecting various equipments to SEEB (v) Supply of copper lug sleeve for 3/16 cable Inspection: Consignee.
Installation of Unit Maintenance Free Earth as supplied under item no. 13.3 of Chapter 13 of SOR . It includes ( i) Digging the earth to the required depth. (ii) Insertion of electrode. (iii) Filling of earth enhancing compound (Approx.30Kg) (iv) Provision of exothermic weld connections to copper tape of 25mm x 6mm x 150mm to the earth electrodes. All material tools and features required for weld will be arranged by contractor. (v) This also includes CC cover 1.5 ft x 1.5 ft. 1 ft wall thickness 84 2 inch with cover 3 inch thickness. Cables 35 Sq.mm/ 16 Sq.mm/10 sq.mm for connecting earth to bus bar, bus bar to bus bar and bus bars to various equipments. Earth electrode of 17.20mm dia and 3.00 meter long high tensile low carbon steel circular rods molecularly bonded with copper and outer surface (minimum copper bonding thickness of 250 micrones to made requirement of underwriter's laboratories (UL) 467-2007 or latest. Copper strips of150mm x 25mm x 6mm to be welded with each earth electrode, copper strips of 300mm x 25mm x 6mm for main equip-potential bus bar, copper strips of 150mm x 25mm x 6mm sub equip potential bus bar in relay room, power room and panel room. GI strip 25mm x 2mm for ring formation of earth pits Earth enhancement material in bags for each Earth Electrode. Inspection chamber of site 300mm x300 mm x 300mm (Inside dimension) of approximate 50mm thick with pulling hooks to cover the earth pits. Note: The installation of this item shall be carried out by the contractor as per RDSO Specn.No. RDSO/SPN/197/2008 or latest and conforming to RDSO Drg. No. SDO/RDSO/E&B/001 or latest.
Supply of axle counter cable's conductor earth resistance sensing unit, microcontroller based for 12 No Conductor with metering facility for for one conductor at a time
DISMANTLING OF EXISTING SIGNALS, APPARATUS CASES, FOUNDATIONS, EPM, WIRES, GATES ETC. TRANSPORTATION OF MATERIAL AS PER TECH. SPECN. Per Detection
Supply of MSDAC complete system (As per annex-A) with all accessories consisting of complete indoor and 89 outdoor equipment including remote diagnostic and monitoring system as per RDSO Specification no. RDSO/SPN/176/2013 Ver.3 with the latest amendment/revision of required Track Sections for entire yard as standby of DC track circuit in two stations: BEF and SGRD (home to home signals of each station). The MSDAC must be compatible with existing installed MSDAC, Inspection-RDSO. Per Detection
Design, Transportation, Installation, testing and commissioning of MSDAC complete system (As per annexure A) with all accessories consisting of complete indoor and outdoor equipment including remote diagnostic and monitoring system as per RDSO Specification no. RDSO/SPN/176/2013 Ver. 3 with the latest amendment/revision of required Track Sections for entire yard as standby of DC track circuit of two stations (home to home signals) of each station.
"Tools Kit for High frequency Digital Axle Counter Multi section. Service test panel including meter for test of 91 track equipment, tools for mounting and adjustment of track equipment and standard jig for drilling holes in rail. It should be as per Principal manufacturers (OEM) recommended list adequate for installation, day to day maintenance, and adjustment of indoor and outdoor gears. This shall also include kit for making and drilling of holes on rail, inspection-Consignee."
Miscellaneous arrangement for NI period comprising of Provision of water-proof temporary goomty/tent at both 92 side of the station yard and at central panel building. Each goomties to be furnished with one iron table, six chairs, emergency light and mosquito repellent caps for NI staff, PA system, crowbar men for operating point and men for supplying water to tents. (Unit-LS/Stn)
Supply & Installation of Earth leakage detecter of 12 channels AC/DC as per specification no. RDSO/SPN/256/2025 ver 2.0 with latest ammendment, Inspection-Consignee.
Supply, installation, testing and commissioning of UL/FM/VDS/LPCB approved Microprocessor based networkable analogue addressable and modular type of Fire alarm control panel with display, in built charging facilities and provision of GSM module suitable to send SMS to configured moblie no. The panel should be equipped with nos. of loops and provision of expandability as per RDSO specification no RDSO/SPN/217/2021ver 3.0 or latest (suitable for distributed as well as 94 centralized). The Control panel shall be the central processing unit of the system, receiving and analyzing signals from probe type bimetallic heat detectors, UV&IR flame detectors, heat and smoke multi sensors, LHS/LHSD interface and manual call points, providing audible and visual information to the user. The panel shall have provision of connectivity of TCP-IP suitable for programming and remote monitoring. The panel shall have dedicated RS 232serial port for direct PC or MODEM connection, for interfacing with existing data logger, optional remote printer. ( Asper RDSO Specification no. RDSO/SPN/217/2021ver 3.0 or latest), Inspection-Consignee.
Supply, installation, testing and commissioning of resettable, addressable multi sensor (Heat & Smoke) which is fully compatible with analogue addressable protocol, Electronically addressed. (As per RDSO Specification no. RDSO/SPN/217/2021ver 3.0 or latest), inspection-RDSO.
Supply, installation, testing and commissioning of addressable, resettable manual call point with integral short circuit isolator, having status LED for alarming & Stand by mode, Electronically addressed. ( As per RDSO Specification no. RDSO/SPN/217/2021 ver 3.0 or latest), Inspection-Consignee.
Supply, Installation, Testing & Commissioning of Resettable, Analogue Type Linear Heat Sensing (LHS) Cable/LHD complying to RDSO/SPN/217/2021 Ver.3 or or later. As it is the latest UL or FM or VDS or LPCB approved / listed, Inspection-Consignee.
Supply, Installation, Testing & Commissioning of LHS/LHD Interface Module with all accessories complying to RDSO/SPN/217/2021 Ver.3 or later. (Inspection by RDSO). As it is the latest UL or FM or VDS or LPCB approved / listed, inspection-RDSO.
Supply, installation and testing and commissioning of addressable Loop powered wall sounder/alarm. (As per RDSO Specification no. RDSO/SPN/217/2021ver 3.0 or latest), Inspection-Consignee.
Supply, installation, testing and commissioning of FRLS/Fire survival circuit integrity cables i.e. armored cable & Power cable with all accessories for connection of all fire alarm devices. (Asper RDSO Specification no. RDSO/SPN/217/2021 ver 3.0 or latest), Inspection-Consignee.
Supply, installation and testing and commissioning of Aspiration Type smoke Detection System complete. (As per RDSO Specification no. RDSO/SPN/217/2021ver 3.0 or latest), Inspection-Consignee.
Supply, Testing & Commissioning of PVC pipe having 25mm dia for aspiration detection supply portion(Number = 03 Meter length), Inspection-Consignee.
Supply of PVC conduit Pipe having Diameter 25mm, inspection-Consignee.
Data logger system for Railway S&T installation As per spec. IRS: S-99 2006 (Amdt-3) or latest. Central 104 Monitoring Unit (Hardware Configuration as per Annexure) with UPS minimum 06 Hrs battery backup and required Software tools. This also includes supply of one no composite computer & printer table (Godrej work station table) for keeping Processor module and one no Godrej make operator chair model PCH7001.1024 digital and 32 analog inputs as per technical specification attached, Inspection-RDSO(except furniture, Inspection-Consignee).
Installation, wiring, testing and commissioning of Datalogger complete along with accessories using Contractors 105 own wiring & fixing materials as per following configuration. (It includes loading of NETWORKING software, networking of data logger, installation of FEP & Fault diagnosis system & validation ). The requisite communication cable/channel for networking will be arranged by Railway. 1024 digital & 32 analog inputs .
SUPPLY OF PROXIMITY SWITCHES FOR SINGLE DOOR ALONG WITH 2 WAY RIGID CONNECTOR FOR WIRE 106 TERMINATION BETWEEN PROXIMITY SWITCHES AND DATA LOGGER,TAG BLOCK AND TESTING OF DOOR CONTACTS AN VALIDATION AND PROXIMITY SWITCH DATA THROUGH DATA LOGGER INCLUDING EMBEDDED SOFTWARE DEVELOPMENT IN DATALOGGER, Inspection-Consignee.
Failure Analysis & Fault Diagnostic software for data logger of 1024 digital inputs, Inspection-Consignee.
Electrically operated lifting barrier complete 110 V AC operated without hand generator as per latest revised spec. RDSO/SPN/208/2012 Ver 2.0, Inspection-Consignee.
Transportation, installation and commissioning of Electrically operated lifting barrier assembly including boom 109 support, boom locking devices, control panel etc as per instructions of site engineer. This includes excavation & casting of pedestal foundation & boom locking arrangement for boom of lifting barrier with contractor's own material including cement & anchor bolts. This also includes complete wiring & testing of the lifting barriers.
Installation & Commissioning of Sliding Boom gate as per the technical specification attached.
Supply of Laptop based work station for data input & configuration, simulation and functional testing, 111 diagnostics and trouble shooting and commissioning of SSI system. Screen-15.6inch, Ram-16 GB, i5 processor, 512 GB PCIeNVMe, Graphics card-NVIDIA GTX 1650 4gb or better configuration. Note:-The technical specification for the concern item is explained Technical Spec. Inspection by Consignee.
Supply of Portable digital auto range multi-meter clamp type with capacity to measure mA AC/DC current with accuracy of (3% of reading) AC/DC upto80Amp(AC/DC), 600V(AC/DC) and 0.1 ohms- 40M ohms, suitable for measurement of Freq., capacitance, complete with Manual, leads, battery and holster etc. Inspection-Consignee against WC & TC.
Supply of Switch Plate lubricant - Cenolube 100or better NLGI 00 GRADE Black colored which should be non asphaltic Non bituminous blend of very heavy oils, inert thickeners and lubricating solids coupled with molybdenum disulfide and graphite with no traces of chlorinated solvent such as 1,1,1 trichloroethane which are flammable and harmful to the environment. Should have a blend of select high viscosity index solvent refined severely hydro finished paraffin base oils and synthetic base fluids. It should incorporate solid lubricants & organo molybdenum disulfide to fill& lubricate micronized asperities to provide & form many films on the contact surfaces to prevent metal-to-metal contact. It shall be designed to be 113 hand applied providing a tough adherent Lubricant film with Tacky semi-dry finish reducing contaminant adhesion. The Lubricant Should Not form a difficult to remove thick DRY film which requires scrapping & solvent cleaning of Switch Plate specially before reapplication The grease should Not need Cleaning or scrapping before Reapplication. The Lubricant should be formulated for tropical climates and should not contain pour point depressants and should Not be too thin. The lubricant shall be Resistant to water wash off & dilution, water insoluble, non-melt and chemically resistant to exposed environment. The grease shall be formulated with Extreme Pressure additives, rust and corrosion inhibitors, anti-wear additives to protect external surfaces against the harsh elements in severe climates, thus reducing rust binding and adhesive wear on switch plates Four Ball Weld LOAD (ASTM- D2596) >600Kg, Copper corrosion 24 hours @ 100c(ASTM D 4048) 1a -2e packing Size20 kg /25kg Drum, Inspection-RITES.
Supply of Dowell's crimping tool of Model make 3D-2 109/108 or similar suitable for crimping lugs from size 0.5 mm to 16 mm, inspection-Consignee.
Copper lug heavy duty Dowell's make or similar, inspection-Consignee.
Color LCD Thermal imager Pocket size camera Make Fluke-PTI120 or Similar, inspection-Consignee
Item Breakup - A 2- Outdoor Signalling works
Supply of 4 conducore disconnect terminal blocks RDSO/SPN/189/2004 ver.3.0 ot latest, Inspection-Consignee.
Supply of End and Intermediate Plate as per RDSO/SPN/189/2004 ver.3.0 Numbers or latest, Inspection-Consignee.
Supply of screwless End Stop as per RDSO/SPN/189/2004 ver.3.0 or Numbers latest, Inspection-Consignee.
Supply of Steel carrier Rail as per RDSO/SPN/189/2004 ver.3.0 or latest, Numbers Inspection-Consignee. Total 119837.00 Earthing of CT Rack, Relay Rack, DG sets etc. including supply of Earthing materials as per the technical specification attached, Item- 4 Inspection-Consignee. S No. Item No Description of Item Unit Qty Rate Amount
Supply Total 74793.00 Supply and fixing of P/G/C markers with complete fittings. All material require for the job such as MS sheet, MS Angle, Nut and Item- 44 bolts, paint & painting materials will be supplied by the contractor as per direction of site engineer as per the technical specification attached, Inspection-Consignee. S No. Item No Description of Item Unit Qty Rate Amount
Supply Total 1782.68 Item- 46 Supply & Installation of Number Plate of Signals as per the technical specification attached, Inspection-Consignee. S No. Item No Description of Item Unit Qty Rate Amount
Supply Total 3781.70 Installation of Warning board along with supply of warning board.This includes concrete foundation of 600 x 600 x 600 mm as Item- 52 per the technical specification attached, Inspection-Consignee. Note -Rail post will be given by railway at the store of consignee. S No. Item No Description of Item Unit Qty Rate Amount
Supply Total 15838.56 Installation of Terminal board for terminating main/tail cable including supply of terminal board as per the technical specification attached, Inspection-Consignee. Note -(1). Termination board of hylem sheet IS:2036 grade P-4 size 6mm thick. (2). Angle Iron Item- 74 Size 40mm X 40 mm X 5 mm at station. (3) Angle Iron size 25 mm X 25 mm X 3 mm suit the size of cases i.e. Single case, Half Case, 50 way JB and as for requirments. S No. Item No Description of Item Unit Qty Rate Amount
Square Execution Foot
Square Supply Foot Total 219648.00 Item- 87 SHIFTING OF LOCATION BOXES as per the instruction of Site-in-charge. S No. Item No Description of Item Unit Qty Rate Amount
Half Case Total 13635.94 DISMANTLING OF EXISTING SIGNALS, APPARATUS CASES, FOUNDATIONS, EPM, WIRES, GATES ETC. TRANSPORTATION OF Item- 88 MATERIAL AS PER TECH. SPECN. S No. Item No Description of Item Unit Qty Rate Amount
LOCATION BOX SINGLE CASE
LOCATION BOX HALF CASE
FOUNDATION SIGNAL / LOCATION BOXES Total 15109.77 Item- Copper lug heavy duty Dowell's make or similar, inspection-Consignee. 116 S No. Item No Description of Item Unit Qty Rate Amount
Size 2.5 sq.mm.
Size 16 sq.mm. Total 22400.00
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
IPASVerificationofBGonlyletter.pdf
ATTACHMENT
STTenderDoc.pdf
ATTACHMENT
JPOforundrtakingearthworkdiggingwork1.pdf JPOforundrtaking earth work digging
ATTACHMENT
Technicalspecification.pdf
ATTACHMENT
PHYNEWMP.pdf
ATTACHMENT
Annexure-A-MSDAC.pdf
ATTACHMENT
JPOforundrtakingearthworkdiggingwork1.pdf
ATTACHMENT
Download all tender documents and submit your bid