REPAIR MAINT OF SEWAGE LINES FOOTPATH FENCING B W ETC OTM ACCN AT MIL STATION JALIPA UNDER GE ARMY BARMER

Amount

Taking out/ Dewatering of sewage water/ muddy water/ sludge/ mud/ silt or any other dirty & filthy material at bottom in foul condition from the manhole, septic tanks and soakage well/ pit by using sewage pump/ mechanically or manually by using buckets/ baskets, lifting the same of any capacity upto 4.50M depth from GL and removing the ejected/ obtained material out side the MD land including taking down precast covers and fixing of the same with CM (1:4) after cleaning without damaging complete all as specified and directed.

Cleaning of SWG/RCC/HDPE/PVC pipe sewage line of 100 to 250mm bore in foul condition by rodding the drain/sewage line using flexible rod/suitable device or by any other means for removing blockage from sewer line, mud, silt and any other debries obtained from sewage line with water to remove blockage and cleaning the entire rubbish, sludge etc and burrying the material obtained from sewage line/ removing the ejected/ obtained material out side the MD land including all precautionery and sefety measures etc complete all as specified and directed.

Removing blockage from water closet, floor or gully or Nahani Trap, traps including removal of grating and refix after cleaning with white cement, and bends without damaging by rodding thoroughly and pouring water under pressure and cleaning, clearing the drainage to efficient and smooth flow of sludge/waste water including 75mm and 110mm connecting pipe complete all as specified and directed by Engineer-in-Charge. NOTE FOR SL NO. 1, 2 & 3 :- (i) Contractor's supervisor will report on all working days along with Two safai wala at 0830 hrs at AGE B/R-I to receive complaints for blockage and to submit completion report on the same day by 1700 hrs. (ii) Printed complaint slip area wise as per format approved by Engineer-in-Charge shall be provided and maintained by contractor. (iii) Rate quoted above shall be deemed to included the cost of all type T&P, equipment, saftey device etc alongwith sufficient labour to full fill the requirement to the entire satisfaction of Engineer-in-charge. (iv) If threre is any major blockage in sewer line/septic tank/ soakage well/pit for which additional Safaiwalas and special T&P is required same shall be provided by contractor without any extra cost to Govt, therefore contractor is adviced to visit the site before quoting the rates in tender. (v) In the event he fails to attend the complaint recovery @ Rs. 1000 per day shall be effected from the amount due to the contractor.

Site clearance, like shrubs, vegetation, grass, weeds, trees, saplings and trees, small plants, Kikkar of stem girth n.exc 30cm measured 1m above average ground level including removing the unserviciable material like branches, leaves, grass & garbage to clear the alignment of existing sewage/drainage line to make site workable condition & making good the disturbed ground complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out hard/dense soil complete all as specified and directed.

All as per Srl item No. 5 above but exc 1.5m depth and n exc 3.0m depth and getting out hard/dense soil complete all as specified and directed.

Returning, filling in including spreading, levelling, watering & well ramming in layers n.exc 25cm complete all as specified and directed.

M&L for Reinforced concrete pipes 100mm bore class NP-2, laid and jointed complete with collars, complete all as specified and directed.

All as per srl item No. 8 above but for 150mm bore pipe.

All as per srl item No. 8 above but for 200mm bore pipe.

M&L for 100mm dia slat-glazed stoneware drain pipes laid in trenches and joints as specified complete all as specified and directed.

All as per srl item No. 11 above but for 150mm bore pipe.

All as per srl item No. 11 above but for 200mm bore pipe.

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in concrete bed to drain pipes including packing under & haunching against the sides of pipes after they are laid & tested for 100mm bore pipe including demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, PCC bad and haunching, complete all as specified and directed.

All as per Sl Item No. 14 above but 150mm bore pipe.

All as per Sl Item No. 14 above but 200mm bore pipe.

M&L for cement concrete Type 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete including demolition of cement concrete (unreinforced) of any description and in any position complete all as specified and directed.

M&L for cement concrete Type 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in surface channels and drains including demolition of cement concrete (unreinforced) of any description and in any position complete all as specified and directed.

M&L for cement concrete Type 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete including demolition of cement concrete (unreinforced) of any description and in any position complete all as specified and directed.

M&L for cement concrete Type B0 1:2:4 (12.5 mm graded aggregate) as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs/benching and the like including weathering, slightly rounded for chamfered angles and throating including demolition, as directing complete all as specified and directed.

Demolition of brickwork or stone, PCC block, boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L for walling of random rubble uncoursed ,well bonded ,bedded and solidly hearted built in CM (1:4) and brought up to course complete all as specified and directed.

All as per srl item No 22 above but except stone.

Extra over lime or sand stone, stone walling for hammer dressing to face stones and dressing or face beds and joints, with maximum depression on face from straight edge held against the dressed surface n exc. 20mm, as specified, of random rubble walling, uncoursed or brought upto courses complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry Type C1, 1:3:6 (20 mm graded aggregate) with solid blocks, exc. 10 cm in width and set in CM (1:6), complete complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:4) mixed with integral WPC on fair faces of brick work or concrete surfaces or stone walls finished even and smooth without using extra cement. Note : WPC shall be measured and paid separately.

Supply only liquid water proofing compound of approved make all as specified and directed .

M&L for precast cement concrete 1:2:4 type B-1 using (20mm aggreates) set in CM (1:4) as in cover slabs (for manhole etc) simillar articles with plain faces (Reinforcement will be measured and paid separately) including demolition of cement concrete (reinforced) in floors / pavings, (below or above ground level) n exc 15 cm thick all as specified and directed.

M&L for Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including demolition of cement concrete (reinforced) in floors / pavings, (below or above ground level) n exc 15 cm thick all as specified and directed.

Formwork to flat rough finished surfaces of soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) (leak proof shuttering) complete all as specified and directed.

S&F for mild steel TMT bars 10mm dia and over cut to length, bent to shape required including cranking, bending, spirally for hooping columns, hooking ends & binding with & including MS wire (annealed) not less than 0.9mm dia of or securing with clips complete all as specified and directed.

S&F for mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping columns, hooking ends & binding with & including MS wire (annealed) not less than 0.9mm dia of or securing with clips complete all as specified and directed.

Dismantling of 75mm to 100mm cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

S&F for 100mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches, fixed to wall complete all as specified and directed.

S&F for 75mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches, fixed to wall complete all as specified and directed.

Fixing only for 100mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches, fixed to wall retrieved from srl item No 34 above complete all as specified and directed.

Fixing only for 75mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches, fixed to wall retrieved from srl item No 34 above complete all as specified and directed.

S&F for 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F for 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F in repairs 100mm bore cast iron branch pieces, single or double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and directed.

S&F in repairs 75mm bore cast iron branch pieces, single or double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and directed.

S&F in repairs 75mm bore cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair 110mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F in repair 75mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

Fixing only in repair 110mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

Fixing only in repair 75mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bend any radius 110mm complete all as specified and directed.

S&F PVC (SWR) bend any radius 75mm complete all as specified and directed.

S&F in repairs 110 mm bore PVC [SWR] Junction single [single "T" or "Y"] equal or unequal, complete all as specified and directed.

S&F in repairs 75 mm bore PVC [SWR] Junction single [single "T" or "Y"] equal or unequal, complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

Cutting into road/ black top/PCC pavement of any thickness including excavation in any type of soil upto 0.50m to 0.80m width and 0.50m to 1.50m depth, refiling, compaction of soil after laying of PCC bed, haunching and pipe, packing and compaction with existing soling/GSB/WBM/WMM, and top surface prepared with 0.15m thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) complete all as specified and directed.

M&L for 75mm thick cement concrete type 1:4:8 type D-2 (using 40mm graded stone aggregate) as in floors and paving, complete all as specified and directed.

Demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and as directed.

M&L for 300mmx300mmx10mm thick non skid polka dots parking floor paver tiles with grey cement and pigment, over and including 15mm thick screed in CM (1:4), set jointed & pointed in neat cement slurry in floors complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block rubber moulded any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade including over 30mm thick sand cushioning complete all as specified and directed.

M&L for Glazed ceramic tiles of size 300mm x 200mm x 7mm/ 450mm x 300mm x 7mm thick (coloured) of superior quality fixed on vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry over 10mm thick backing coat in CM (1:4) and pointed in coloured cement to match complete all as specified and directed.

M&L for non skid ceramic tiles of size 7 to 8mm thick (coloured) (Square/rectangular) area of each tile exc 0.06 but n exc 0.11 sqm, in floors, set & jointed in neat cement slurry and pointed in coloured cement over 15mm thick screed bed in CM (1:4) complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white including P or S trap, connection to drain (or outgoing pipe) and to flushing pipe 32mm PVC with and including plastic water closet seat, white closed pattern with flat bottom, cover and mild steel hinges device complete all as specified and directed.

S&F in repair vitreous china squatting Pan “Orissa” Pattern, of size 580mm x 440mm white with integral foot rests and trap (excluding flushing cistern and flush pipe) including trap and provn of cement concrete bedding complete as fixed complete all as specified.

S&F in repair PVC valveless flushing cistern, low level white with inlet ball valve float and handle including brackets complete fixed capacity of flush 10 ltrs complete all as specified and directed.

S&F in repair 15mm bore, 450mm long, PVC connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends as fixed in repairs complete all as specified and directed..

S&F in repair 15mm bore CP fancy type stop valves/angle cock, cast copper alloy, screwed both ends for iron pipe or for union complete all as specified and directed.

Dismantling of fencing wire mesh any type complete all as specified and directed.

Dismantling of posts or struts (wood, steel or RCC) any section, including taking out embedded portion from concrete, brick work, masonry, etc. and making good disturbed ground complete all as specified and directed.

S&F for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

S&F for Mild steel in flat, round or square bars, in available lengths, Fe 290 (Gde E-165) in fencing complete all as specified and directed.

Preparation of New or previously untreated steel surface of any description over 10cm girth or width, not otherwise describedand applying two coats of synthetic enamel (ordinary tint) over one coat of red oxide primer complete all as specified and directed.

Preparation of New or previously untreated steel surface of any description n exc 10cm girth or width, not otherwise describedand applying two coats of synthetic enamel (ordinary tint) over one coat of red oxide primer complete all as specified and directed.

Supply chain link MS galvanised fencing, any size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

S&F for 5 to 10mm dia shank mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm long and n exc 10cm long complete all as specified and directed.

S&F in repair galvanized 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs @ 75mm spacing and strining and fixing to any type of standard rails straining bolts, including securing or type at crossing etc complete all as specified and directed.

Devi Engineeing

M/s Malinath Electricals

Lalit and Brothers