SPECIAL REPAIRS TO BLDG NO. P86-01 (OFFRS MD ACCN) ADDN/ALTN AND UPGRADATION IN CERTAIN BUILDING PROVN OF TOILET GENERATOR SHED TILING IN JCOs-ORs MD ACCN WATER GEYSERS EXHAUST FANS AND DEMOLITION OF OTM ACCN AT KALUCHAK MIL STN UNDER GE KALUCHAK

Amount

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as specified & directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each, complete all as specified & directed.

Pressed steel frames of size 105mmx60mm made of 1.25mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate., complete all as specified & directed. Note : PCC for filling of hollow portion shall be measured and paid for separately.

Pressed steel frames of size 125mmx60mm made of 1.25mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate., complete all as specified & directed. Note : PCC for filling of hollow portion shall be measured and paid for separately.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II, complete all as specified & directed.

PCC 1:3:6 nominal mix, type C-0 using 12.5mm graded crushed stone aggregate as in filling of pressed steel door frames/chowkats, complete all as specified & directed.

35mm thick factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled shutters (two panels) with lock rail and panels of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified & directed.

35mm thick 2nd class hard wood (Sal/Hollock), glazed and skeleton shutters (factory made), open rebated and prepared to receive glass or gauge etc., divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, size of members of shutters as specified in clause 8.24 (b) of SSR Part-I, fitted to chowkat, complete all as specified & directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made of MS tube for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet 5mm thick to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplied & fitted in the frame at site as per specification & drawings shown in SSR Part-II, complete as specified & directed.

Aluminium anodized powder coated (minimum thickness 50 micron) frame (for door) of size 101.60mm x 44.45mm made out of 1.60mm thick aluminium section, powder coated, fixed to floor/wall with plugs and screws, complete all as specified & directed.

Aluminium anodized powder coated (minimum thickness 50 micron) double window shutter (external glazed & internal stainless steel wiremesh) made of aluminium section of size 44.45 x 44.45mm of 1.60mm thickness including powder coated aluminium handle, tower bolt, hinges, jointing cleats, rubber gasket etc, glazing with 5mm thick glass sheet with glazing clips of size 19 mm x 17 mm made out of 0.70 thick aluminium section not less than 0.97 Kg/RM, complete all as specified & directed. Note : Quoted rate shall be deemed included cost of 5 mm thick glass, stainless steel wire mesh & all fittings and no extra shall be provided on this account.

Mild steel galvanised wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, wire staples or beading etc, complete all as specified & directed.

Butt hinges, medium weight, cold rolled, mild steel 100mm long, complete all as specified & directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed, 300mm long, complete all as specified & directed.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 150mm long, complete all as specified & directed.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 100mm long, complete all as specified & directed.

Aluminium handle, cast type, anodised, 150mm long, complete all as specified & directed.

Aluminium handle, cast type, anodised, 100mm long, complete all as specified & directed.

300mm ordinary rat tail rod pattern door spring including roller and roller plate of mild steel and fixed to pressed steel frame / MS frame/ wooden chowkhats including necessary welding work etc where-ever required, complete all as specified & directed.

18/19mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber framed work as in cup board shutters, shelves etc., with 3mm thick teak wood beading/lipping all around, fixed in repairs, complete all as specified & directed.

12 mm thick, 7 ply veneered decorative plywood ordinary grade-1 (with BWR resin) with decorative face veneers on one face, fixed with nails to timber frame work of wall/ceiling, complete all as specified & directed.

Magnetic catcher, heavy duty, brass body and striking plate, fixed in cupboard shutters, complete all as specified & directed.

40mm dia, copboard knobs fixed with nut, screw and washer of mild steel, brass polished, complete all as specified & directed.

Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30mm, complete all as specified & directed.

2nd class hard wood (Sal/Hollock) as in scantling, clean sawn timber, fixed in framed work, complete all as specified & directed.

25mm dia stainless steel curtain rod of 1mm wall thickness in one length as per door/window with stainless steel bracket & knob of suitable size, stops rollers etc, fixed in repairs, complete all as specified & directed.

Taking up or down steel tubing and connections 15mm bore, complete all as specifed & directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc,; and cutting chases for concealed water tubing or concealed conduit wiring etc., and making good, cutting not exc. 20cm girth in brick/stone walls, complete all as specified & directed.

Unplasticized PVC pipes of pressure rating 10 kgf/sq. cm, 15mm bore, jointed as per manufacturers instructions with all fittings such as sockets, bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc., fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Taking up or down steel tubing and connections 20mm bore, complete all as specifed & directed.

Unplasticized PVC pipes of pressure rating 10 kgf/sq. cm, 20mm bore, jointed as per manufacturers instructions with all fittings such as sockets, bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc., fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Dismantling water tanks of capacity exc 500 litres but n exc 1000 litres, complete all as specified & directed.

Rotationally moulded polyethylene water storage tank (cylindrical vertical with closed top), double layer, connecting up pipes, securing access covers etc, hoisted & fixed in position of capacity 500 ltrs, complete all as specified & directed.

Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule for bore of pipe 20mm, complete all as specified & directed.

Vitreous china wash down water closet (Pedestal pattern), white with ‘P’ or ‘S’ trap, plastic water closet seat, white, closed pattern with flat bottom and cover, mild steel chromium plated or aluminium hinging device, chromium plated jet nozzle with 1500mm long PVC pipe fixed with screws of suitable size including making connections to trap and to flush pipe, fixing flushing cistern etc. and making good to floors, fixed in repairs, complete all as specified & directed.

Vitreous china, wash hand basin with pedestal, flat back, white of size 580mmx450mm including brackets, brass CP waste coupling 32mm dia with long screwed shank and fly nuts, chain and plug, porcelain stopper, PVC 32mm dia waste pipe including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs, complete all as specified & directed.

PVC connections 15mm size with PTMT nuts of length 450mm, fixed in repairs, complete all as specified & directed.

Hand Shower (Health Faucet) with 1 meter long easy flex tube in chrome finish & wall hook, fixed in repairs, complete all as specified & directed. Make. Jaquar, Cat Part No. ALD-CHR-565 or equivalent model of make specified in List of Makes/ Manufacturers/ Producers here-in-after.

PVC valveless, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long, fixed in repairs, complete all as specified & directed.

Bib tap, 15mm bore, fancy type, chromium plated, cast copper alloy with capstan head, screwed down, screwed for iron pipe or for brass ferrule, fixed in repairs, complete all as specified & directed.

Chromium plated wall mixer 3-in-1 system with provision for both telephone shower & overhead shower complete with 115mm long bend pipe, fixed in repairs, complete all as specified and directed Make : Jaquar Cat Part No. 281 or equivalent model of make specified in List of Makes/ Manufacturers/ Producers here-in-after.

Brass chromium plated mixer for mixing hot & cold water screwed down for iron pipe and fixed for 15mm bore of pipe, fixed in repairs, complete all as specified & directed.

Stop/Angle valves, 15mm bore, fancy type, chromium plated, cast copper alloy with capstan head, concealed type, screwed down, high pressure, both ends screwed for iron pipe or for union etc., fixed in repairs, complete all as specifed & directed.

PVC cabinet made of ABS material of size 500x400mm with glass front, fixed in repairs, complete all as specified & directed. Make.Prayag

Grating doom with waste hole, 125mm dia of PTMT (Minimum weight 40gms), fixed in repairs, complete all as specified & directed.

Towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges, fixed in repairs, complete all as specified & directed.

PVC (SWR) floor trap, plain with grating including jointing to waste pipe with solvent cement, dia of outlet 75mm, fixed in repairs, complete all as specified & directed.

PVC (SWR) pipes, 110mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to wall, fixed in repairs, complete all as specified & directed.

Soap dish, brass chromium plated, of size 100x60mm, fixed to walls with chromium plated screws, fixed in repairs, complete all as specified & directed.

Toilet paper holder with flap, brass chromium plated, fixed in repairs, complete all as specified & directed .

Stainless steel sink with drainage board made of stainless steel 1mm thick for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever cast iron bracket, connecting union etc. and overall size 915x460mm with bowl size 410x330x160mm, fixed in repairs, complete all as specified & directed.

Stainless steel plate rack of size 750x900x250mm made out of 1mm thick stainless steel having partitions as per sample kept in AGE office, complete all as specified & directed.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, fixed in repairs, complete all as specified & directed. Make.Jaquar

Taking down cement plaster on brick or stone surfaces etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specifed & directed.

10mm thick rendering in cement mortar 1:3 on concrete surfaces ceiling and similar items, surface finished even and smooth without using extra cement, complete all as specified & directed.

15mm thick rendering in cement mortar 1:6 on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified & directed.

15mm thick rendering in cement mortar 1:4 on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified & directed.

Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified & directed.

Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:4, complete all as specified & directed.

Preparation of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified & directed.

Preparation of old decorated plastered or unplastered surface of ceiling by brooming down or by steel wire brushes, scraping down smoke spots, moulds, moss and efflorescent salts, trading oil, greasy spots etc. and applying two coats of white wash, complete all as specified & directed.

Preparation of new plastered surfaces of walls and applying two coats of oil bound emulsion over a coat of primer over 2mm thick wall care putty, complete all as specified & directed.

Complete removal of existing treatment of any description by washing, rubbing down and stopping of distempered/painted wall surfaces and applying 2mm thick wall care putty primed with primer and painted with two coats of oil bound emulsion, complete all as specified & directed.

Preparation of new plastered or concrete surfaces of walls and applying two coats of cement base paint of any tint over a coat of primer, complete all as specified & directed.

Preparation of old decorated plastered or unplastered surface of walls including cornices, pilasters etc by brooming down or by steel wire brushes, scraping down smoke spots, moulds, moss and efflorescent salts, trading oil, greasy spots etc. and applying two coats of cement base paint, complete all as specified & directed.

Preparation of old painted wooden or wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified & directed.

Preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified & directed.

Preparation of old decorated steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified & directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified & directed.

Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but nexc 0.18 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:4, complete all as specified and directed.

Glazed ceramic coloured tiles of size 450mmx300mm, thickness 7mm as in vertical surfaces such as skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed.

18-20mm thick jet black granite stone work (table rubbed and polished) machine cut in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, rounding edges of stone slabs over & including 15mm thick screed bed in cement mortar 1:4, complete all as specified & directed.

Vitrified light shade ceremic tiles 10mm thick (Square/rectangular) polished area of each tile not exceeding 0.36Sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in cement mortar 1:4, complete all as specified & directed.

Vitrified light shade ceremic tiles 10mm thick (Square/rectangular) polished area of each tile not exceeding 0.36Sqm, as in vertical surfaces such as skirting/dado etc., set and and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10mm thick rendering in cement mortar 1:4, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified & directed.

50mm thick PCC 1:3:6, nominal mix, type C2, using 40mm graded crushed stone aggregate as in plinth protection and similar items, surface finished even and smooth without using extra cement including forming and filling of joints 12mm wide with bituminous filler, complete all as specified & directed.

Sink made of stainless steel 1mm thick for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever cast iron bracket, connecting union, waste coupling 40mm of PTMT (half or full threaded) minimum weight 45 gms, PVC waste pipe etc. and overall size 610x510mm with bowl size 530x430x203mm including , complete all as specified & directed.

Aluminium anodized powder coated (minimum thickness 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified & directed.

Aluminium anodised powder coated (minimum thickness 50 micron) door shutters aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified & directed. Note : Sheet glass will be measured and paid separately under respective item.

5.50mm thick frosted glass as in aluminium door/window with aluminium hollow beading/glazing clip including rubber gasket etc, complete all as specified & directed.

Brass chromium plated shower rose of 125mm size with or without swivel joints, fixed in repairs, complete all as specified & directed.

Kitchen sink mixer with regular swinging spout, chromium plated, wall mounted with connecting legs, flanges, florentine cocks etc , fixed in repairs, complete all as specified and directed Make : Jaquar Cat Part No. COS 103309N or equivalent model of make specified in List of Makes/ Manufacturers/ Producers here-in-after.

5 to 8mm thick printed frosted etching glass for shutter, cupboard shelves with necessary fittings including cutting and necessary fixtures screws, complete all as specified & directed. Make.Dorma

18mm thick BWR grade marine ply for shutters/ shelves/ kitchen cabinet/ drawer covered with 1mm thick designer laminated sheets and back side covered with 0.80mm thick designer laminated sheet with 2mm thick PVC lapping (edge band) to be fixed with hydraulic press at factory including pressing lipping and back sides covered,, complete all as specified & directed.

Rolling sliding channels of size 450mm length, fixed in cupboard with screws for holding stainless steel basket as in drawers, complete all as specified & directed. Make. Godrej/ Hettich/ Zuari/ Sleek

Stainless steel designer handle (heavy duty) of 200mm size, fixed to drawers or cupboard shutters, complete all as specified & directed.

Stainless steel designer handle (heavy duty) of 100mm size, fixed to drawers or cupboard shutters, complete all as specified & directed.

Stainless steel basket for keeping cutlery made of stainless steel wires or sheets as per design & size approved by GE, fixed to drawers or cupboards with sliding channels as per requirement with stainless steel screws as in modular kitchen pattern design, complete all as specified & directed. Make. Godrej/ Hettich/ Zuari/ Sleek

Stainless steel fasteners of size 75mm long steel supports, fixed to walls, complete all as specified & directed. Make. Godrej/ Hettich/ Zuari/ Sleek

Glass corner shelf of 5.50mm thickness with bracket, fixed to walls, complete all as specified & directed. Make.Jaquar

Dismantling asbestos cement (corrugated, semi corrugated etc.) sheets in roof coverings, complete all as specified & directed.

Dismantling posts or structs (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground, posts embedded in concrete, brickwork, masonry etc., complete all as specified & directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified & directed.

Dismantling timber scantling 40 Sqcm and over in section, in any position (framed work), complete all as specified & directed.

Dismantling wall & ceiling board (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified & directed.

Surface dressing n exc 15cm deep in any type of soil, complete all as specified & directed.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan in any type of soil and getting out, complete all as specified & directed.

PCC 1:4:8, nominal mix, type D-2 using 40mm graded crushed stone aggregate as in foundations, filling & mass concrete, complete all as specified & directed.

Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:6, complete all as specified & directed.

40mm thick PCC 1:2:4, nominal mix, type B0, using 12.5mm graded crushed stone aggregate as in damp proof course to horizontal or vertical surfaces including necessary formwork, complete all as specified and as directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25cm, complete all as specifed & directed.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified & directed.

TMT bars 10mm dia & over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, conforming to grade Fe-500, complete all as specified & directed.

All as per Srl item No. 104 above but 5mm dia & over upto & including 10mm dia in stirrups, spacers and binders.

Use & waste of form work to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc alo splays between floors and beams for rough finished surfaces of concrete, complete all as specified & directed.

Use & waste of form work to edges of concrete flats, treads, break in floors, window cills, concrete railings openings in concrete walls, floor and roof and n exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n. exc. 20cm wide for rough finished surfaces of concrete, complete all as specified & directed.

Use & waste of form work to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc alo splays between floors and beams for rough finished surfaces of concrete, complete all as specified & directed.

RCC 1:2:4, nominal mix, type B-1, using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified & directed.

10mm thick rendering in cement mortar 1:4 on concrete surfaces of RCC roof slab and similar items using integral water proofing compound, surface finished even and smooth without using extra cement, complete all as specified & directed. Note : Integral water proofing compound shall be measured & paid for seperately under respective items.

Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan to any radius, half brick thick walls built in cement mortar 1:4, complete all as specified & directed.

Hard core of gauge n exc 63mm using broken stone or boulders, deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface, complete all as specified & directed.

75mm thick PCC 1:4:8 (nominal mix), type D-2 using 40mm graded crushed stone aggregate as in sub base of floor, complete all as specified & directed.

25mm thick PCC 1:2:4 nominal mix, type B-1, using 20mm graded stone aggregate as in floors, finished even and fair to receive floor finishes, complete all as specified & directed.

Glazed ceramic coloured tiles of size 300mmx200mm, thickness 7mm as in vertical surfaces such as skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed.

Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.06 sqm but nexc 0.11 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:4, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed, 300mm long, complete all as specified & directed.

PVC valveless, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long, complete all as specified & directed.

PVC (SWR) floor trap, plain with grating including jointing to waste pipe with solvent cement, dia of outlet 75mm, complete all as specified & directed.

PVC (SWR) pipes, 110mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified & directed.

PVC (SWR) pipes, 75mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified & directed.

PVC (SWR) pipes, 75mm bore, single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified & directed.

110mm bore PVC (SWR) bends any radius with oval access door, complete all as specified & directed.

75mm bore PVC (SWR) bends any radius with oval access door, complete all as specified & directed.

PVC (SWR) vent cowl of size 75mm bore, complete all as specified & directed.

Galvanized iron water tubing, medium grade, 15mm bore with all fittings such as sockets, bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc., fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Galvanized iron water tubing, medium grade, 20mm bore with all fittings such as sockets, bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc., fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Angle valves, cast copper alloy, 15mm bore, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., complete all as specifed & directed.

Vitreous chinaware squatting pan, 'Orissa Pattern' size 580mm x 440mm with integral foot rests, white, with ‘P’ or ‘S’ trap, front or back inlet, including provision of lime concrete, making connections to trap and to flush pipe etc. and making good to floors, complete all as specified & directed.

Viterous china urinal, bowl type flat back, size 465x355x265mm (minimum) white with grating and union for discharge pipe, complete including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, complete all as specified & directed.

Vitreous china, wash hand basin, flat back, white of size 550mmx400mm including brackets, brass CP waste coupling 32mm dia with long screwed shank and fly nuts, chain and plug, porcelain stopper, PVC 32mm dia waste pipe including cutting for and pinning in ends of brackets or erecting stand, complete all as specified & directed.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered `Hot’ or `Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, complete all as specified & directed.

Stop valves, cast copper alloy, 15mm bore, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., complete all as specifed & directed.

Bib taps, 15mm bore, cast copper alloy, with crutch or butter fly handle, screwed down, screwed for iron pipe, or brass ferrule, complete all as specifed & directed.

3mm thick figured glass, pin headed type and glazing with oil putty or wooden beads or glazing pins in squares not exc. 0.5 Sqm in each pane, complete all as specified & directed.

Preparation of new plastered surfaces of walls and applying three coats of white wash, complete all as specified & directed.

Concrete bed to 150mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid in cement concret 1:3:6 (Nominal mix) type C-2 using 40mm graded stone aggregate and tested, complete all as specified & directed.

Salt-glazed stoneware drain pipe, grade ‘A’ internal dia of pipe 150mm, laid in trenches and jointed, complete all as specified & directed.

Precast cement concrete 1:2:4 (nominal mix), type B-1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for manhole etc.), and similar articals with plain faces, set in cement mortar 1:4 complete all as specified & directed.

TMT bars 6 to 8mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, conforming to grade Fe-500, complete all as specified & directed.

PCC 1:2:4, nominal mix, type B-1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified & directed.

Construction of Septic Tank for 10 users including excavation in any type of soil, foundation in PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) brick work in cement mortar 1:4, RCC (M-25 design Mix) slab including cast iron manhole cover having 6mm plate embedded all around with angle iron frame vent shaft etc, complete all as specified and shown on CE Pathankot Zone TD Drawing No CEPZ/C-TD/013/13 Sheet 1 to 5.

Construction of soakage well 1.20m internal dia and 2.40m depth including excavation in any type of soil, PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in footing brick honey comb/ solid brick masonry in cement 1:4, RCC (M-25 design mix) cover slab filled with brick bats including intercepting chamber screen chamber and disposal of soil, complete all as specified and shown on CE Pathankot Zone TD Drawing No CEPZ/C-TD/013/13 Sheet 1 to 5. Note : 1. During excavation if unexpected water is encountered, the same shall be bailed out / de-watered by the contractor mechanically or manually without any extra cost. 2. The excavated surplus soil shall be removed to a distance exceeding 500mtr and not exceeding 1500mtr and deposited where directed by the Engineer-in-Charge.

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in any type of soil, complete all as specified & directed.

Excavation in post holes (or similar holes) each not exc. 0.50 cum, in any type of soil and getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exc. 25cm, watering and removal of excavated materials to a distance n. exc. 50m and making good surfaces, complete all as specified & directed.

PCC 1:2:4, nominal mix, type B-2 using 40mm graded crushed stone aggregate in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases), complete all as specified & directed.

50mm thick PCC 1:2:4, nominal mix, type B1, using 20mm graded crushed stone aggregate as in floor, surface finished even and smooth without using extra cement, laid in alternate bays, complete all as specified & directed.

PVC floor dividing strips, 1.5mm thick and 38mm wide, complete all as specified & directed.

Rolled mild steel work in roof trusses (framed) trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-290 grade-E-165, complete all as specified & directed.

Mild steel framed work as in plates (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes, without any attachment, conforming to Fe-290 grade-E-165, complete all as specified & directed.

Pre-painted galvalume aluminum zinc coating GI based profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified & directed.

Preparation of new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified & directed.

Zero crank hinge, heavy duty, soft closing type as in shutter of cupboards in kitchen, complete all as specified & directed. Make. Godrej/ Hettich/ Zuari/ Sleek

Rotationally moulded polyethylene water storage tank (cylindrical vertical with closed top), double layer, connecting up pipes, securing access covers etc, hoisted & fixed in position of capacity 1000 ltrs, complete all as specified & directed.

Taking down carefully, copper / aluminium conductor unserviceable / perished point wiring (any type) for light/ fan/ light socket or power socket etc complete with fittings such as switches, sockets, ceiling roses, pendant holders, bracket holder, light fittings, regulators etc, including making good to disturbed surfaces of wall/floor etc, complete, all as specified & directed.

Taking down carefully unserviceable main switche fuse unit, distribution boards of any type/size from their position including making good to disturbed surfaces of wall etc, complete all as specified & directed.

Taking down carefully existing sub main wiring with aluminium conductor/copper conductor cable of any size with GI earth wire including wooden batten etc and making good disturbed surface of walls etc, complete all as specified & directed.

Taking down carefully electric meter of any description by disconnecting electrically and refixing the same in old or new location, complete all as specified & directed.

Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 1.5 Sqmm drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling including cutting chases as required, terminated in pressed steel sunken box having wall thickness as directed suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories including single core FRLS PVC insulated unsheathed solid copper conductor cable of 1.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one light/fan/bell point controlled by one way switch using proper colour coding, complete all as specified & directed.

All as per Srl item No. 157 above but for one 3/5 pin 5 Amps socket outlet on same board.

All as per Srl item No. 157 here-in-before but for one 3/5 pin 5 Amps socket outlet on independent board.

Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 4.0 Sqmm drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling including cutting chases as required, terminated in pressed steel sunken box having wall thickness as directed suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories including single core FRLS PVC insulated unsheathed solid copper conductor cable of 2.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one 3/5 pin socket outlet 15 Amps independent using proper colour coding, complete all as specified & directed.

Switch piano flush type 5 Amps 240 volt, single pole one way, complete all as specified & directed.

Switch socket combination, two in one, 5 pin type, 5 Amp, flush type universal, 240 volt, complete all as specified & directed.

Switch socket combination, two in one, 6 pin type, 5 & 15 Amp, 240 Volt, flush type universal, complete all as specified & directed.

Ceiling rose surface type, bakelite 65mmx50mm, 3 terminals, 240 Volt, complete all as specified & directed.

Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified & directed.

Inverter LED lamp 6500K, 900lm in white colour of 9 watt, base cap B-22 with poly carbonate diffuser and aluminium heat sink, complete all as specified & directed.

Electronic fan regulator, 2 module, 120watt, (5 stepped type), 240 Volt for 1200/1400mm sweep AC ceiling fan, complete all as specified & directed.

Bell push flush type, one way 5 Amps single pole one way, complete all as specified & directed.

Electronic bell, musical type, AC, 240 volts, single pole, complete all as specified & directed.

Energy efficient LED bulk head luminaire, 1x15 watt, wall mounted made of die cast aluminium with opal diffuser IP-65, LED lamp, lamp holders, etc. complete with all accessories including connecting up with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting 230V, 50 HZ, complete all as specified & directed.

Tube light fitting integrated type suitable for LED 20W (4 feet) indoor, decorative aluminium extruded T5 LED batten complete with housing with all accessories pre-wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting, complete all as specified & directed.

Metallic exhaust fan, 300mm (12") sweep, single phase, 230 volts, 50 Hz AC, 1400 RPM, energy saving, heavy duty totally enclosed, heavy duty motor with die-cast aluminiun rotor mounted on two ball bearings, complete with louvers and shutters, connecting electrically using 3 core 0.75 Sq mm PVC insulated flexible copper conductor cable, complete all as specified & directed.

Factory made epoxy powder coated distribution board, SPN, 8 ways with metal door (IP-43 protection), confirming to IS : 8623 fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall, suitable for universal mounting including 100 Amp copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts, suitable for SPN/DP MCB as incomer and SP MCB outgoing, complete all as specified & directed .

Factory made epoxy powder coated distribution board, SPN, 12 ways with metal door (IP-43 protection), confirming to IS : 8623 fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall, suitable for universal mounting including 100 Amp copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts, suitable for SPN/DP MCB as incomer and SP MCB outgoing, complete all as specified & directed .

MCB, single pole, 6 to 32 Amp, 50 Hz AC supply, 10 KA repturing capacity, 240 Volt, 'C' series, complete all as specified & directed.

MCB, double pole, 6 to 32 Amp, 50 Hz AC supply, 10 KA repturing capacity, 240 Volt, 'C' series, complete all as specified & directed.

MCB, double pole, 40 Amp, 50 Hz AC supply, 10 KA repturing capacity, 240 Volt, 'C' series, complete all as specified & directed.

Tamper proof with inbuilt intelligence electronic energy meter, single phase, two wire direct connected meter with parameter (voltage P-n, PF, frequency current line KW demand, LCD display, optical port class 1.0s), 240 volts 10-60 Amps, complete with meter box single phase with locking arrangements molded in UV stabilised transperant/ flame retardant high grade engineering plastic with unique arrangements for plifer proof interlocking with hinge type box with connection of suitable size wire including seal and sealing wire, complete all as specified & directed. Make : L&T Cat Part No. WM101BC7DL0BOX or equivalent of ABB/ Schenider/ Secure/ Havells/ HPL Notes : (i) MES No to be marked on the meter with black paint as directed. All details ie Bldg No, Qtr No, Initial Reading, SL No of new meter etc as per specified format are to be submitted by the contractor. (ii) All unserviceable old meter retrived to be deposited to MES Store Yard.

Sub main wiring using uniform coding of wiring with two runs of 6.0 Sqmm single core FRLS PVC insulated unsheathed cable upto and including 1100 volts grade with multistranded copper conductor drawn into and including PVC concealed conduit 'ISI marked' of 25mm dia medium grade as required, fixed in concealed surface of wall/ceiling including cutting chases as required with all fittings and fixing accessories & one run of 4.00 Sqmm FRLS PVC insulated solid copper conductor for earth continuity wire in green colour, complete all as specified & directed. Note:- Two runs of copper conductor 6.0 sqmm and one run of 4.00 Sqmm copper earth wire including PVC conduit of 25mm dia will be measured and paid as one unit only.

Earthing complete with galvanized mild steel earth plate electrode size 600mm x 600mm x 6mm thick buried directly in ground (preferably in vertical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 3 meter (BGL), connected to galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore “medium grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 15mm bore 'light grade' galvanized iron protection pipe for earth lead wire upto 5m length, charcoal, common salt etc including connected to test point and testing on completion, complete all as shown in electrical plate No 3 of SSR Part-I 2009 & as directed.

Intergral LED security light luminaire 60W LED, 230 volts made up of pressure die-cast aluminium housing with toughned glass and high power LEDs and secondry lenses with IP66 protection, efficacy 110 lumens per watt including 10 KV surge protection device, mounted on & including GI bracket made out of 40mm bore medium grade pipe of 1.70m length, bent to required shape, fixed on PCC/Steel pole with 02 Nos. clamps of flat iron (40 x 6mm), nuts, bolts and washers including painting with two coats of aluminium paint over a coat of red oxide zinc chrome primer, making connection with PVC copper conductor cable of 1.5 sqmm and taking down old unserviceable light fitting, complete all as specified & directed.

Supply, hanging and testing of 1200mm sweep, 230 volts, AC ceiling fans, 2 star BEE rated energy efficient ceiling fan conforming to IS:374-2019, having 3 blades alongwith copper wound stator (capacitor start) with minimum air delivery 210 cubic metre per minute, power consumption not more than 50 watt, top speed minimum 370 RPM or higher, speed control by 5 step electronic regulator including capacitor, down rod, canopy, making connection with three core flexiable copper cable of 1.50 Sqmm upto ceiling rose & taking down old unserviceable ceiling fan of any type/size from existing location and depositing in MES store, complete all as specified & directed.

Supply, installation and testing of water heater storage type (Geyser) single phase, 230V, 50Hz, 5 star energy saving, high density PUF insulation tank made of heavy duty magnesium anode rod with steel core to protect enamelled tank from rust & corrosion, vertical installation type, 25 Litre capacity, 2000 Watt rated power, incoloy 800 glass coated heating element, tank coating of ferro glass dry powder tank made of ultra thick super cold rolled steel plates, rated pressure 0.8MPa, IPX4 protection consist of safety valves, thermal cut off, thermostat including connecting up fixed to walls by drilling of holes, grouting of bolts of suitable size with nuts etc and making good disturbed surface, complete all as specified & directed.

Cutting & screwing of existing water supply line of 15mm bore for alterations or additions (or lengthening screw on pipe to form connector) including testing after completion, complete all as specified & directed. (each cut measured)

Bib tap, 15mm bore, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.

Cutting holes in existing brick walls for making opening for fixing of exhaust fan of 300mm sweep including grounting bolts/nuts and making good disturbed surface of walls using cement sand mortar 1:4, complete all as specified & directed.

Sheet metal enclosure for DBs single door when MCBs to be used, single pole and neutral with suitable bus bas 240V, 2 way, complete all as specified & directed.

M/S RAVINDER SINGH

S R CONSTRUCTIONS

NARESH KUMAR AND COMPANY

M/S Vishwakarma Builders