REPAIR ROUTINE MAINT OF 12 NOS ELECTRIC LIFTS MAKE MONARCH OF G5 G6 G14 STOREY BUILDING AT NAVY NAGAR UNDER GE NW NAVY NAGAR COLABA MUMBAI

Amount

Sch 'A' Part- I Repair/maintenance of lifts including carrying out daily check and periodical services of fully automatic electrical lift with power operated door, simplex collective control system with repair/maintenance of unserviceable damaged parts such as bearings, bushes, all type of guide shoes, headers, hangers, door ropes,door cards,car door sills, landing door sills, door locks, control cards, and its contacts, hall push buttons and its spares, connector/links, welding of cracked /broken and MS parts, Landing operating Panel of any size and capacity, repairs /maint of unserviceable damaged door safety edge and sensor mechanical safety lock, magnetic lock or contact, car position indicator, and all connected accessories, necessary wiring of hall push button assembly, repair/maintenance of broken COP/LOP buttons and display, including cover, Fire alarm, Firemen button glass, Intercom, alarm/hooters, Maintenance of damaged hand rail, Shaft, light/switches, complete with illuminated push button and direction indicator with LED display with LPT/LPC card of stainless steel inclusive of harness wiring for laminating of push button of each floors and cutting wall making good disturbed surface with masonry work to make with existing surface & cable as per requirement for safe operation of lifts , fixing of loose rail bracket with necessary masonry work ,cabin, minor repair of cabin light, shaft light and minor repair of cabin fan , ensuring safe and smooth functioning of lift and complete maintenance of car top, binding of loose wire at control panel and rust painting at car top and door and allied parts with testing, two coats of Painting of Gear motor, all MS channels and Control panels using spray gun complete, dewatering of lift wells in case of any emergency arise all as directed by Engineer-in-Charge for the following lifts

Notes : - (i) The Contractor has to carry out the AMC of the Lifts through OEM only. (ii) The AMC should cover any / all parts of Lifts if its functions found defective the same should be repaired or replaced by the OEM as per the timeline covered under norms. (iii) Rewinding of motor if required will be done by the contractor and no extra cost will be given by the department. (iv) The detailed duty mechanics of the firm shall report to the JE Concerned at the Lift complaint cell i.e. R-12 building . New Navy Nagar for receiving the complaints daily including sunday and holiday. iv) The detailed lift mechanics shall sign ( Their shift wise) in the attendence register kept with lift cell.

8 Ps lift (544 Kgs) ( G+6/ 14 Storey) in bldg R-11 (East), F-3, F-4 (03 Lifts)

13 Ps Lift ( 884 Kg) (G+ 6/14 storey) in Kumbh, G Block, H Block, R-1, R-2, R-3, Makar, R-22 (A & E Wing) (09 Lifts)

Disconnecting and taking out old/ unserviceable travelling cable from hoist way and supply and fixing new travelling cable PVC Insulated 24 Core with stranded copper conductor, 1100 volts grade of size 0.75 Sqmm conforming to relevant IS including criping with lugs appropriate thimbles complete all as specified and directed by Engineer-in-Charge.

Disconnecting and taking out unserviceable COP assembly for G+5/G+14 storey building, supply and fixing new car operating panel assembly completed with illuminated push button for floor position alarm, non stop door open , door close, cabin fan, cabin light stop, attend out key etc with direction indicator,with LED display with CPI card of stainless steel face plate in and including necessary wiring for laminating push button of each floors and cutting wall, making good disturbed surface with machinary work to complete all as specified and directed by Engineer-in-charge.

Taking down old unserviceable cabin fan from car cabin and supply and fixing new cabin fan non oscillating type axial flow, single speed 300mm sweep, 240 volts ISI mark with grill complete all as directed by Engineer-in-charge.

Replacement of automatic door drive unit without motor on car top with VVVF of 1 HP capaicity all as specified and directed by Engineer-in-Charge.

Dismantling and taking out unserviceable safety edge of any type supply and fixing full beam infrared sensor upto full length of car doors (2.00 mtr) for (6 Ps) & (8 Ps) complete all as specified and directed by the Engineer-in-Charge.

Dismantling and taking out unserviceable old landing push button box alongwith illuminated call button with control wiring supply and fixing landing push button box alongwith illuminated call button with control wiring for G+14 storey building complete all as directed by Engineer-in-charge

Disconnecting and taking out old/unserviceable Governer rope of size 8 mm dia (8/19 Construction) ungalvanised including necessary connection with pulley in machine room and shaft pit complete with clamps, nuts bolts, and washers etc, for high rise building for 8/13/Goods lifts complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair Emergency alarm with complete accessories alongwith box including connecting cables for G+14 storey building all as specified and directed by Engr-in-Charge.

Disconnecting and taking out unserviceable ARD and repair of ARD for proper operation including necessary wiring with machine and controller consisting of the following :-

Replacement of PCB Card, relay with control wiring for G+14 storey building.

Replacement of sealed maintenance free batteries ( Set of Four) each of 12 volts, 18 AH (Maintenance free)

Taking down old unserviceable OSG Pulley from the position and supply and fixing New OSG Pulley both top and bottom for 08 PS/13 PS/Goods Lift as specified and directed by Engr-in-Charge.

Taking down old unserviceable Chequered plate and supply and fixing Aluminium Chequered plate of 5mm thick duly fixed with nuts, bolts, washers,screws and covers with aluminimum angles section of size ( 40x40x4 mm thick) on corner of cabin in and including platform base of 10mm thick plywood of 08 Ps/13 Ps/Goods lifts

Dismantling and taking out unserviceable old control panel and control wiring and supply and fixing new CAN BAS Integrated Drive based collective control panel in hinged MS powder coated cabinet with control wiring comprising with multiple microcontrolled programmed chip based controlled by pulse modulation, complete with all safties such as thermal overload protection, over current protection, auto phase reverse link to each other in net work and compatible to 18 KW/24HP capacity VVVF drive including proper connection with proper lugs, terminal connectors screws and motor connection with galvanised sheet trunking 24 SWG including wiring of main motor with suitable size of stranded copper cable etc complete all as specified and directed by Engineer-in-Charge.

Disconnecting and taking out old/unserviceable shaft wiring, supply and fixing of shaft wiring in hoist way upto lower limit with PVC insulated copper conductor cable single core, 1100 Volts grade 0.75 Sqmm 24 Nos single core & 1.0 Sqmm for earth wire duly bunched with wire binding locking strip, drawing through in and including galvanised sheet metal trunking of 24 SWG up to ground floor in hoist for control to all function including in built connection for control panel, PCB, Hall push button, fire switch and lower limit switch all as specified and directed by the Engineer-in-Charge. for G+14 Storey building.

Disconnecting and taking out defective dynamic breaking resistance from controller and supply and fixing new aluminium covered wire wound dynamic breaking resistor to absorb the reverse energy dissipation of motor during regeneration in control operation suitable for 11.0KW/15HP motor.

Taking down old unserviceable Announcement system and supply and installation, testing and commissioning of MP3 voice announcement system in the controller and high quality speaker on car top, with necessary provision of shaft wires and travelling cable complete as specified. The audio indicator shall anounce floor position, ARD made operation, overload announcement etc and continious mild music in hindi and can be programmable for more music. The announcement system shall be in hindi and english.

Disconnecting and taking out defective unserviceable main drive (any type) from existing control panel and supply and fixing CAN BAS Integrtaed drive suitable for Goods/13 Ps lift G+14 storey building complete with all electric connection.

Taking down old/unserviceable main pulley from motor and supply and fix of main pulley of 4/5/6 grooves suitable for existing motor and fixing of existing rope complete as specified and directed by Engineer-in-Charge.

Replacement of unserviceable ARD control system and commissioning and testing of new ARD system suitable for upto 15/18 KW motor including wiring with connected items in existing G+14 Storey building 8 ps/ 13 ps/ Goods lifts 415V,50 Hz,3 phase with a speed of 1.2 mtr/sec comprising with maintenance free battery 12 V, 18 AH (04 Nos Maintenance free battery) to match with the existing capacity motor and controller system complete all as specified and directed by Engineer-in-Charge.

Taking down old unserviceable main steel wire rope after disconnecting old wire rope from counter weight, pulley and car cabin and supply and fixing new main steel wire rope 13 mm dia, ungalvanised, 8/19 construction in and including necessary connection with counter weight, pulley and car cabin with clamps, nut, bolts and washers etc complete all as directed by Engineer-in-Charge.in 6/13 /Goods Lift, G+5/G+6/G+16 Storey buildings.

Shree Elevator Engineering Co. (BID ID -3179043)

Veer High Tech Solution (BID ID -3177555)

Escon Elevators Pvt Ltd (BID ID -3177487)

shakti engineering and electrical works (BID ID -3178780)