Loading
Loading…
Loading…
Tender ID
Tender Value
₹29.0 Cr
EMD Value
₹16.0 L
Closing Date
17 Feb 2026, 3:00 pmClosed
Yes (up to 3 members)
No
Two Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
90 days
Expenditure
Capital (Works)
GENERAL
22 conditions · 3 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
If JV firms are allowed to participate, Financial eligibility of the JV Firm shall be adjudged based on satisfactory fulfillment of the Para No.17.15.2 of Part-I of IRSGCC-2022 [including upto ACS no.10]
NOTE: If the tender is not accompanied by the certificate(s) in support of financial eligibility as above, the tender shall be rejected. No post-tender correspondence will be entertained.
(a)The tenderer must have successfully completed or substantially completed any of the following categories of works during last 07 (seven) years, ending last day of month previous to the one in which tender is invited[Even though the work might have commenced before the qualifying period]: Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work each costing not less than the amount equal to 60% of advertised value of the tender.
The total value of similar nature of work completed during the qualifying period and not the payments received within qualifying period alone, shall be considered. In case, final Bill of similar nature of work has not been passed and final measurements have not been recorded, the paid amount including statutory deductions will be considered. If final measurements have been recorded and work has been completed with negative variation, then also the paid amount including statutory deductions will be considered. However, if final measurements have been recorded and work has been completed with positive variation but variation has not been sanctioned, original agreement value or last sanctioned agreement value whichever is lower shall be considered for judging eligibility.
In case JV firms are allowed to participate, Technical Eligibility of the JV Firm shall be adjudged based on satisfactory fulfillment of the Para No.17.15.1 of Part-I of IRSGCC-2022 [including upto ACS no.10]
The works executed by tenderer for any Govt. / Govt. bodies / PSUs and public listed company (as detailed in Note for Para No.10.1 of part-I of IRSGCC 2022 including upto ACS no.10) shall only be considered for fulfilling of Technical Eligibility Criteria.
The work experience certificate shall be in the name and style of the tenderer participating or as per provisions under Clause 17.15 of Part-I of IRSGCC 2022 (including upto ACS no.10) for JV Firm, if eligible to 1.3.1 participate. However, in case the tenderer is submitting the certificate issued to a JV firm of which the tenderer is a member, the credentials proportionate to his share in the JV will be considered. The tenderer shall submit an attested copy of relevant JV Agreement along with the Tender.
The work experience certificate shall be issued by an officer not below the rank of JA Grade or Bill passing Officer in Railways and Bill passing 1.3.2 Officer/Executive In-charge of work in other Govt. / Govt. bodies / PSUs. The certificate should bear the signature and seal of the issuing officer, name of the department etc.
Note for Para No.10.1 of Part-I of IRSGCC (including upto ACS no.10); Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated / registered atleast 5 years prior to the date of closing of tender, shall also 1.3.3 be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Defination of Similar Work :- Any Civil Engineering Work (excluding Track works / zonal works)
43 conditions · 8 needing a document upload
The Bid Security shall be deposited either in cash through e- payment gateway or submitted as Bank Guarantee bond from a scheduled commercial bank of India. The Bank Guarantee bond shall be as per Annexure- VIA and shall be valid for a period of 90 days beyond the bid validity period. Tenderers may refer Para 5 of IRSGCC -2022 -Part-I (including up to ACS no.10) for other details in regard to payment of bid security. The original Bank Guarantee should be delivered in person to Dy.CE/C/Plg./SC, Room no.206A, 2nd floor, Rail Nirman Nilayam, S.C. Railway, Secunderabad -500025. Note: As per ACS no.5 issued by Railway Board vide letter No.2022/CE-I/CT/GCC- 2022/Policy dt.20.10.2023, "The original Bank Guarantee should be delivered in person to the oficial nominated as indicated in the tender document before closing date for submission of bids (i.e., excluding the last date of submission of bids (Authority: PCE/SC's lr.no.W.496/Policy/Vol.IX, dt:31.05.2024).
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Following documents shall be enclosed
In case of Sole Proprietorship Firm, the documents to be attached with the tender are: (i)An undertaking that he is not blacklisted or debarred by Railways or any other Ministry / Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of the partnership firm or JV in which he was / is a partner/member. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract.(ii) All documents in terms of Para 10 of the Tender Form (Second Sheet) of IRSGCC 2022(Including upto ACS no.10)
In case, the tenderer is bidding on behalf of HUF the documents to be attached with the tender are : (i) A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii)An undertaking that the HUF is not blacklisted or debarred by Railways or any other Ministry/Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as member of JV in which the HUF was / is a member. Concealment/wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract.(iii) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of IRSGCC 2022 (Including upto ACS no.10)
In case, the Tenderer is a Partnership Firm, the following documents shall be submitted: (i)A notarized copy of the Partnership Deed or a copy of the Partnership Deed registered with the Registrar. (ii)A notarized or registered copy of Power of Attorney in favour of the individual to tender for the work, sign the agreement etc. and create liability against the firm.(iii)An undertaking by all partners of the partnership firm that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders/contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP in which they were/are partners/members. Any concealment/wrong information in regard to above shall make the bid ineligible or the contract shall be determined under Clause 62 of the General Conditions of Contract.(iv)All other documents as mentioned in Para 18 of the tender form (second sheet) of IRSGCC- 2022(Including upto ACS no.10)
In case tenderer is a LLP Firm registered under LLP Act-2008, the following documents shall be submitted: (i)A copy of LLP Agreement (ii)A copy of Certificate of Incorporation (iii)A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv)An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract (v)All other documents in terms of Para 10 of Tender form(2nd sheet) of IRSGCC- April-2022 Part- I(Including upto ACS no.10). (vi) All other documents as per Clause 14 of IRSGCC -April -2022- Part I (including upto ACS no.10)
In case the Tenderer is a Company registered under Companies Act-2013:-The tenderer(s) shall submit the following documents: (i)The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii)A copy of Certificate of Incorporation (iii)A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company. (iv)An undertaking that the Company is not blacklisted or debarred by Railways or any other Ministry / Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of the partnership firm or JV in which the Company was / is a partner/member. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract. (v)All other documents in terms of para 10 of tender form (2nd Sheet) of IRSGCC-2022(Including ACS no.10) (vi) All other documents as per Clause 14 of IRSGCC -April -2022- Part I(including upto ACS no.10)
In case the Tenderer is a Registered Society & Registered Trust, the following documents shall be submitted: (i)A copy of Certificate of Registration (ii)A copy of Memorandum of Association of Society / Trust Deed (iii)A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust.(iv) A Copy of rules and regulations of the society (v)All other documents in terms of Para 10 of Tender form(2nd sheet) of IRSGCC- April-2022 Part- I(Including upto ACS no.10). (v) All other documents as per Clause 14 of IRSGCC -April -2022- Part-I(Including upto ACS no.10).
In case JV Firms are allowed to participate: JV firm should upload Memorandum of Understanding [MOU] as per the format attached as annexure to the tender in DOCUMENTS. Submission of all other documents by JV firm / Members of JV should also be as per Cl.No.17.14 of Part-I of IRSGCC-2022(Including upto ACS no.10)
Uploading of other relevant documents connected to the tender; such as Declaration regarding employment of Retired Engineer/ Retired Railway officer, NEFT Form, List of Personnel/Organization, List of Plant/ machinery, (As per the formats attached in the list of Documents whatever attached and remaining in their own format to be submitted)etc
The successful bidder shall submit "Performance Guarantee" amounting to FIVE percent (5%) of contract value after award of the work.
The General Conditions of Contract governing the performance of the works covered by this tender are the IRS GCC-2022 [including upto ACS no.10]. A soft copy of the Indian Railway Standard General conditions of Contract is uploaded in the attached documents to the tender for reference. Hard copy of IRSGCC (with up-to-date correction slip) may be perused in the office of the Chief Administrative Officer/ Construction/ South Central Railway / Secunderabad - 500071. The tenderer/s is/are deemed to have kept himself/themselves fully Informed of the provisions of the IRS General conditions of Contract including all corrections and Amendments issued up to date (as on date, IRS GCC-2022 upto ACS no.10 shall be considered) while submission of offer and any claim that he/they is/are not aware of any amendment or correction slip to the IRSGCC shall not be entertained.
STUDY OF DRAWINGS AND LOCAL CONDITIONS: The drawings for the works can be seen in the office of the Chief Administrative Officer, Construction, S.C.Railway, Secunderabad - 500071 or in the office of the concerned field Deputy Chief Engineer / Construction / S.C.Railway . It should be noted that these drawings are meant for general guidance only and Railway may suitably modify them during the execution of work according to the circumstances without making the Railways liable for any claims on account of such changes. If there is any variation between the description in the tender and the detailed plans, the Engineer-in-Charge will operate the correct description and his decision is final and binding on the tenderer/ Contractor. The Tenderer/Contractor is required to inspect the sites of works and acquaint himself with the site conditions, availability of approaches for transporting of men and materials, space and other factors relating to the works, availability of labour, electricity and water, etc., before quoting his rates. The extent of lead and lift involved in the execution of works and any difficulties involved in the execution of work should also be examined before formulating the rates for complete items of works described in the schedule. The Tender submitted will be deemed to have been made after such inspection.
DRAWINGS FOR WORKS: The percentage rates for the schedule items and itemized rates for the non-scheduled items quoted by the tenderer as may be accepted by the railways will, hold good irrespective of any changes, modifications, alterations, additions, omissions in the locations of structures and detailed drawings, specifications and/or the manner of executing the work. It should be specifically noted that some of the detailed drawings may not have been finalised by the Railway and will, therefore, be supplied to the contractor as and when they are finalised on demand. No compensation whatsoever on this account shall be payable by the Railway Administration. No claim whatsoever will be entertained by the Railway on account of any delay or hold up of the works arising out of delay in approval of drawings, changes, modifications, alterations, additions, omission and the site layout plans or detailed drawings and design and/or late supply of such material as are required to be arranged by the Railway or due to any other factor on Railway Accounts.
Manual tenders, supporting documents etc., sent by Post/FAX/Courier or in Person SHALL NOT BE ACCEPTED.
All requisite documents are to be properly submitted online only a n d the bidders should ensure that the content of the documents uploaded is distinctly legible/readable.
CORRIGENDUM NOTICE ON IREPS: [I]Railway may modify the tender document by issuing online corrigendum through "www.ireps.gov.in" 15 days prior to the tender closing date. For the purpose of CORRIGENDUM in the tender, NIT period is splitted as under: (a) ADVERTISEMENT PERIOD: The time during which all information pertaining to tender shall be available but offers cannot be submitted (b) OFFER SUBMISSION PERIOD: 15 days prior to closing of tender, during which tenderers can submit their offer.
If the Bid of a Tenderer is seriously unbalanced in relation to the Engineer's estimate of the cost of work to be performed under the contract, the Railways may require the tenderer to produce detailed price analysis for any or all items of the Tender Schedule, to demonstrate the internal consistency of those prices with the construction methods and schedule proposed.
Applicable for the tenders with eligibility criteria: The offer of Tenderer(s) who do not enclose Work Experience Certificate & Financial eligibility Certificate with requisite details, and supporting documents along with their Tender to establish their credentials shall be summarily rejected, even though they are working contractors or contractors on approved list.
The offer shall be evaluated only from the certificates/documents submitted along with the tender offer.
Any Certificate /Documents offered / submitted / received after the tender opening shall not be given any credit and shall not be considered.
Attestation of documents may be self attested or attested by a Gazetted Officer.
Railway reserves the right to verify the authenticity of the documents/information furnished.
TAXES: if rates of existing GST or cess on GST for Works Contract is increased or any new tax /cess on Works Contract is imposed by Statute after the date of opening of tender but within the original date of completion/date of completion extended under clause 17 & 17A of Part-II of IRSGCC-2022 (including upto ACS no.10) and the Contractor thereupon properly pays such taxes/cess, the Contractor shall be reimbursed the amount so paid. Further, if rates of existing GST or cess on GST for Works Contract is decreased or any tax/cess on Works Contract is decreased / removed by Statute after the date of opening of tender, the reduction in tax amount shall be recovered from Contractor's bills/Security Deposit or any other dues of Contractor with the Government of India.
This tender complies with PUBLIC PROCUREMENT POLICY ORDER-2017 dated 19.07.2024. Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tenderer(s) shall note that conditional/alternate offer will not be considered and will summarily be rejected, even though such condition makes them as the lowest tenderer.
After opening of the tender, any document pertaining to the constitution of sole proprietorship Firm/Partnership Firm/ Registered Company/ Registered Trust/ Registered Society/ HUF/LLP etc. shall be neither asked nor considered, if submitted. Further, no suo moto cognizance of any document available in public domain (i.e, on internet etc) or in Railway's record/office files etc. will be taken for consideration of the tender, if no such mention is available in the tender offer submitted{Asper clause no. 14(iv) Part I of IRSGCC 2022 including upto ACS no.10}
As per clause no.5 part I of IRSGCC 2022 (including upto ACS no.10) the details of exemptions/discount of Bid Security payment is as follows:
i) Any firm recognized by Department of Industrial Policy and Promotion (DIPP) as 'Startups' shall be exempted from payment of Bid Security.
iii) Labour Cooperative Societies shall deposit only 50% of Bid Security as mentioned in the tender
SCR Construction Organization: Hyderabad Division-Augmentation of infrastructure facilities for Maintenance of Vande Bharat rakes at Train Set Maintenance Depot at Moula-ali.
05-CAO-C-SC-2026
05-CAO-C-SC-2026
Open
Works - General
12 Months
Unknown (Unspecified Location)
₹0
₹16.0 L
17 Feb 2026
23 Jan 2026
248 items across 2 schedules · ₹27,95,32,450.55 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| CARRIAGE OF MATERIALS | — | — | — | — | |
| By Mechanical Transport including loading, unloading and stacking | — | — | — | — | |
| 1 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. | cum | 15000 | 494.1 | 74,11,500 |
| EARTH WORK | — | — | — | — | |
| General | — | — | — | — | |
| Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in- charge. | — | — | — | — | |
| 2 | All kinds of soil | cum | 14789 | 177.5 | 26,25,047.5 |
| Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. | — | — | — | — | |
| 3 | Ordinary rock | cum | 8000 | 498.9 | 39,91,200 |
| CONCRETE WORK | — | — | — | — | |
| CEMENT CONCRETE (CAST IN SITU) | — | — | — | — | |
| Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : | — | — | — | — | |
| 4 | 1:3:6 (1 Cement : 3 coarse sand (zone- III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) | cum | 1760 | 7,178.75 | 1,26,34,600 |
| DAMP-PROOF COURSE | — | — | — | — | |
| 5 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) | Sqm | 31 | 410.85 | 12,736.35 |
| MISCELLANEOUS | — | — | — | — | |
| Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. | — | — | — | — | |
| All works upto plinth level : | — | — | — | — | |
| 6 | Concrete of M15 grade with minimum cement content of 240 kg /cum | cum | 300 | 8,986.15 | 26,95,845 |
| 7 | Concrete of M20 grade with minimum cement content of 270 kg /cum | cum | 4500 | 9,212.6 | 4,14,56,700 |
| REINFORCEMENT CEMENT CONCRETE | — | — | — | — | |
| FORM WORK | — | — | — | — | |
| Centering and shuttering including strutting, propping etc. and removal of form for | — | — | — | — | |
| 8 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 1677 | 392.15 | 6,57,635.55 |
| 9 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. | Sqm | 5172 | 842.5 | 43,57,410 |
| 10 | Suspended floors, roofs, landings, balconies and access platform | Sqm | 2100 | 927.25 | 19,47,225 |
| 11 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm | 1920 | 736.4 | 14,13,888 |
| Edges of slabs and breaks in floors and walls | — | — | — | — | |
| 12 | Under 20 cm wide | Metre | 1680 | 208.55 | 3,50,364 |
| STEEL REINFORCEMENT | — | — | — | — | |
| Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. | — | — | — | — | |
| 13 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg | 231980 | 107.85 | 2,50,19,043 |
| DESIGN MIX CONCRETE | — | — | — | — | |
| Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: | — | — | — | — | |
| All works upto plinth level | — | — | — | — | |
| 14 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 4640 | 9,504.75 | 4,41,02,040 |
| 15 | Concrete of M30 grade with minimum cement content of 350 kg /cum | cum | 840 | 9,655.7 | 81,10,788 |
| All works above plinth level upto floor V level | — | — | — | — | |
| 16 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 1610 | 9,860.4 | 1,58,75,244 |
| 17 | Concrete of M30 grade with minimum cement content of 350 kg /cum | cum | 6150 | 10,011.35 | 6,15,69,802.5 |
| 18 | Concrete of M35 grade with minimum cement content of 370 kg /cum | cum | 170 | 10,162.35 | 17,27,599.5 |
| 19 | Add for using extra cement in the items of design mix over and above the specified cement content therein. | Quintal | 2330 | 733.5 | 17,09,055 |
| MASONRY WORK | — | — | — | — | |
| EXPOSED BRICK WALL | — | — | — | — | |
| Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : | — | — | — | — | |
| 20 | Cement mortar 1:6 (1 cement : 6 Coarse sand) | cum | 310 | 8,752.55 | 27,13,290.5 |
| WOOD AND P.V.C. WORK | — | — | — | — | |
| FRAMES AND TRUSSES | — | — | — | — | |
| Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). | — | — | — | — | |
| 21 | Second class teak wood | cum | .5 | 1,42,949.7 | 71,474.85 |
| Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. | — | — | — | — | |
| Second class teak wood | — | — | — | — | |
| 22 | 35 mm thick shutters | Sqm | 15 | 4,111.95 | 61,679.25 |
| Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. | — | — | — | — | |
| 23 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 14 | 3,167.95 | 44,351.3 |
| BRASS FITTINGS | — | — | — | — | |
| 24 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. | Each | 5 | 854.65 | 4,273.25 |
| 25 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. | Each | 5 | 1,124.85 | 5,624.25 |
| ANODISED ALUMINIUM FITTINGS (ALL FITTINGS SHALL BE ISI MARKED) | — | — | — | — | |
| Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc.complete: | — | — | — | — | |
| 26 | 125x63x4 mm | Each | 20 | 126.65 | 2,533 |
| Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : | — | — | — | — | |
| 27 | 200x10 mm | Each | 10 | 99.7 | 997 |
| Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : | — | — | — | — | |
| 28 | 125 mm | Each | 10 | 66.25 | 662.5 |
| Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. | — | — | — | — | |
| 29 | Single rubber stopper | Each | 5 | 39.6 | 198 |
| STEEL WORK | — | — | — | — | |
| General | — | — | — | — | |
| 30 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 47600 | 117.35 | 55,85,860 |
| 31 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 100000 | 133.7 | 1,33,70,000 |
| 32 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. | Kg | 5000 | 97.2 | 4,86,000 |
| Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. | — | — | — | — | |
| 33 | Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides | Sqm | 10 | 1,133.55 | 11,335.5 |
| FLOORING | — | — | — | — | |
| VITRIFIED FLOOR TILES | — | — | — | — | |
| Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting t h e joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. | — | — | — | — | |
| Glazed Vitrified tiles Matt/Antiskid finish of size | — | — | — | — | |
| 34 | Size of Tile 600 x 600 mm | Sqm | 110 | 1,464.85 | 1,61,133.5 |
| ROOFING | — | — | — | — | |
| RAIN WATER SPOUT AND PIPE | — | — | — | — | |
| Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. | — | — | — | — | |
| 35 | 110 mm diameter | Metre | 720 | 377.4 | 2,71,728 |
| Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : | — | — | — | — | |
| 36 | Crimp curve | Sqm | 120 | 496.75 | 59,610 |
| 37 | Gutter (600 mm over all girth) | Metre | 500 | 1,313.7 | 6,56,850 |
| FINISHING | — | — | — | — | |
| CEMENT PLASTER (IN COARSE SAND) | — | — | — | — | |
| 20 mm cement plaster of mix : | — | — | — | — | |
| 38 | 1:6 (1 cement: 6 coarse sand) | Sqm | 2000 | 466.05 | 9,32,100 |
| CEMENT PLASTER IN TWO COATS | — | — | — | — | |
| 39 | 18 mm cement plaster in two coats under layer 12 mm thick cement plaster1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand). | Sqm | 2700 | 518.55 | 14,00,085 |
| EXTERIOR FINISHING | — | — | — | — | |
| Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : | — | — | — | — | |
| 40 | Two or more coats on new work | Sqm | 5000 | 155.9 | 7,79,500 |
| Painting with aluminium paint of approved brand and manufacture to give an even shade . | — | — | — | — | |
| 41 | Two or more coats on new work | Sqm | 2000 | 146.8 | 2,93,600 |
| DISMANTLING AND DEMOLISHING | — | — | — | — | |
| General | — | — | — | — | |
| Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. | — | — | — | — | |
| 42 | Nominal concrete 1:4:8 or leaner mix (including equivalent design mix) | cum | 730 | 1,503.6 | 10,97,628 |
| Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. | — | — | — | — | |
| 43 | In cement mortar | cum | 220 | 2,060.2 | 4,53,244 |
| Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: | — | — | — | — | |
| 44 | G.S. Sheet | Sqm | 1739 | 164.95 | 2,86,848.05 |
| ROAD WORK | — | — | — | — | |
| MISCELLANEOUS | — | — | — | — | |
| 45 | Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). | cum | 695 | 9,823.8 | 68,27,541 |
| WATER SUPPLY | — | — | — | — | |
| PP-R PIPES | — | — | — | — | |
| Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge. External work | — | — | — | — | |
| 46 | PN - 10 Pipe, 50 mm OD (SDR-11) | Metre | 440 | 450.95 | 1,98,418 |
| 47 | PN - 10 Pipe, 160 mm OD (SDR-11) | Metre | 2000 | 2,746.85 | 54,93,700 |
| Providing and fixing PPR Unions | — | — | — | — | |
| 48 | PPR Union 50mm | Each | 150 | 782.1 | 1,17,315 |
| 49 | PPR Union 63mm | Each | 150 | 913 | 1,36,950 |
| ALUMINIUM WORK | — | — | — | — | |
| General | — | — | — | — | |
| Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : | — | — | — | — | |
| For fixed portion | — | — | — | — | |
| 50 | Powder coated aluminium (minimum thickness of powder coating 50 micron) | Kg | 400 | 530.9 | 2,12,360 |
| Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): | — | — | — | — | |
| 51 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) | Sqm | 10 | 1,505.25 | 15,052.5 |
| WATER PROOFING | — | — | — | — | |
| General | — | — | — | — | |
| Grading roof for water proofing treatment with | — | — | — | — | |
| 52 | Cement mortar 1:3 (1 cement : 3 coarse sand) | cum | 7 | 16,112.1 | 1,12,784.7 |
| Schedule total | ₹27,95,32,450.55 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
EMPLOYMNTOFRETIREDRAILWAYOFFICERSCERTIFICATEFORMAT.pdf
NEFT_FORM_GCC_2022.pdf
DETAILSOFPERSONNEL,PLANTANDMACHINERYWORKSONHANDFORMATS.pdf
AFFIDAVIT_ANNEXURE-Vwith_ACS-4_GCC-2022.pdf
FormatforBankGuarantee11.10.2019ver-2.pdf
Agt_format_for_JV_withACS-3_GCC-2022..pdf
SCRCon-BidSecuritydeclaration.pdf
MOUFormatforJVfirms_1.pdf
SpecialConditions-Measurementofworksbycontractor28.08.21-Ver-1.pdf
IRGCC-2022-uptoACS-10consolidated_1.pdf
PublicProcurementPolicy19.07.2024.pdf
TECHCONDITIONS.pdf
Brandsandmakesapprovedlist-2025.pdf
TSSpecialConditionsGeneralwithIRGCC-2022.pdf
PROFORMA_for_BIDCAPACITYcorrected22.08.2022.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .