CONSTRUCTION OF NEW CENTRAL ADMINISTRATIVE BUILDING AT DISTRICT COLLECTORATE PREMISES, TALUKA AND DISTRICT RATNAGIRI.

Amount

Item No. 1 :- Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 0.00 to 1.50 metre) By Manual Means

Item No. 2 :- Excavation for foundation in laterite rock (soft or hard) including trimming and levelling the bed for the foundation, removing the excavated material up to a distance of 50 metres beyond the building area, stacking as directed, dewatering and back filling with available murum, watering, ramming etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Item No. 3 :- Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/ murum watering, ramming etc. complete. (Lift upto 1.5 m). By Mechanical Means

Item No. 4 :- Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Item No. 5 :- Providing soling using 80 millimeter size trap metal in 15 centimeter. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete.

Item No. 6 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-15 of trap metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No.7 :- Providing and laying Cast in situ/Ready Mix cement concrete M-35 of trap metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No. 8 :- Providing and laying Cast in situ/Ready Mix cement concrete M-35 of trap metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork,cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

K) For Terrace Floor

Item No. 9 :- Providing and laying Cast in situ/Ready Mix cement concrete M-35 of trap metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

K) For Terrace Floor

Item No. 10 :- Providing and laying Cast in situ/Ready Mix cement concrete M-35 of trap metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

K) For Terrace Floor

Item No. 11 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 12 :- Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

K) For Terrace Floor

Item No. 13 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 14 :- Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/ steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Crushed sand VSI Grade)

J) For Eighth Floor

K) For Terrace Floor

Item No. 15 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap metal for plain or molded sills, cornice, jambs, block in course, or architraves of required size and shapes including steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided,finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer etc. complete, With fine aggregate (Crushed sand VSI Grade)

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 16 :- Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

K) For Terrace Floor

Item No. 17 :- Providing and constructing laterite stone masonry in cement mortar 1:6 in Foundation and plainth including raking out joints whhen plastering is to be done/Striking joints when no plastering is to done, wateringand scaffolding with all leads and lifts etc. complete. For Ground Floor

Item No. 18 :- Providing and constructing laterite stone masonry in cement mortar 1:6 in superstructure including raking out joints when plastering is to be done/striking joints when no plastering is to be done, watering and scaffolding with all leads and lifts etc. complete.

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

K) For Terrace Floor

Item No. 19 :- Providing internal cement plaster 12 millimeter thick in single coat in cement mortar 1:3 with neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete.

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

K) For Terrace Floor

Item No. 20 :- Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 millimeter thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 millimeter thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

K) For Terrace Floor

Item No. 21 :- Providing waterproof plaster in W.C. and bath 20 millimeter thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing (and filling joints of Nahani trap and any outlet by properly) etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 22 :- Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 23 :- Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete.

J) For Eighth Floor

K) For Terrace Floor

Item No. 24 :-Providing and Fixing Laterite Stone Cladding to Elevation, Entrance Gate, Column, Name board and Compound wall etc. for decorate purpose, etc. complete.

B) For First Floor

C) For Second Floor

D) For Third Floor

E) For Fourth Floor

Item No. 25 :- Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 26 :- Providing and fixing in position after hoisting, precast 1:2 cement mortar reinforced jali 80 mm thick with 3 mm diameter mild steel bar reinforcement, of approved design on both sides, fixing in cement mortar 1:3 and curing etc .complete.

B) For Ground Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

Item No. 27 :-Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 millimeter thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete. For Frame

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 28 :- Providing and fixing machine cut machine polished 18 millimeter to 20 millimeter thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 29 :-Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 millimeter to 20 millimeter thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.

A) For Ground Floor

B) For First Floor

C) For Second Floor

Item No. 30 :-Providing and Fixing Processed Stone Cladding on wall surface/ plywood surface. RCC pardi/ Wall and all type of Interior, Exterior Compound wall and Gate etc. of cladding processed stone with material of Processed clay, Wooden chips, Silica sand, Cement, GFRC admixtures, Colour pigments, Fiber up to thick of 230 mm/ 25 mm including scaffolding, fixing of screw, etc. (Granite caldding)

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 31 :- Providing and laying vitrified mirror / glossy finish tiles decorative type having size 800 X 1500 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete.

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 32 :- Providing and laying vitrified mirror / glossy finish tiles having size 800 X 1500 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 33 :- Providing and laying vitrified rustic matt stone finish tiles having size 600 mm x 1200 mm to 8 to 10mm thickness and confirming to IS.15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete.

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 34 :- Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete.

A) For Basement Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 35 :- Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 36 :-Item No. 36 : Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS.15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc.complete. For Toilet.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 37 :- Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 millimeter x 450 millimeter size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished granite 16 to 20 mm top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 cm height and top granite of 75 x 40 cm including cutting, opening for sink of required size in kadappah as well as granite etc. complete. (Platform top size 5.00 m x 0.60 m and height is 0.75 m)

A) For Basement

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 38 :- Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete.

A) For Basement

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 39 :- Supplying and fixing of semi utilized structutural glazing System with Aluminium Frame to be done in 114 x 57x 1.5mm thick for mullion & transome to be done in 63x57x1.5mm thick panel section to be used for glass panel with 15/20micron colour anodizing, double side spacer tap to be used for fixing of glass to double side spacer tap to be used for fixing of Glass to aluminium. Dow Corning 995structure silicon shall be used for fixing of glass to aluminium 789 shall be used weather silicon, EPDM and which shall be cladded with 6mm thick blue tinted toughened Glass to be used MS bracket for mullion fixing SS Nut bolts, MS Anchor etc complete.

B) For Ground Floor

C) For First Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

Item No. 40 :- Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex.Engineer is necessary before use)

A) For Basement

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 41 :- Providing and applying plaster with plaster of paris in 6mm thickness to previously plaster surface in all position including preparing the surface scaffolding etc. complete.

A) For Basement

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 42 :- Providing and fixing in position U.P.V.C.(Unplasticized Poly Vinyl Chloride) having multi- chambered outer frame section (73 x 50)mm with an outer wall thickness of 2mm & steel reinforcement, multi-chambered slider frame (73x 60) mm with steel reinforcement, multi- chambered slider sash (46x 82) mm with steel reinforcement designed to give optimum strength, 5 mm thick toughened double glass with 12 mm spacer of good quality including alluminium track, Inter-locking profile, coextruded beadings, EPDM gaskets,silicon sealent,sliding handle, fixtures and fastenings (couplings, hinges) including with all required screws and nuts with all necessary U.P.V.C. sections as per the detailed drawing and as directed by Engineer-In-Charge etc. complete.

A) For Basement

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 43 :- Providing and laying in trenches 15 millimetre diameter CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 44 :- Providing and laying in trenches 20 millimetre diameter CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 45 :- Providing and laying in trenches 25 millimetre diameter CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 46 :- Providing and laying in trenches 32 millimetre diameter CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 47 :- Providing, laying and fixing P.V.C. pipe of 50 millimeter diameter with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 48 :- Providing and fixing 100 millimeter diameter stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 49 :- Providing, laying and fixing P.V.C. pipe of 75 millimeter diameter with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 52 :- Providing and fixing 50 mm diameter water meter with non-return valve including strainer,sockets/ union nut and including water meter box making locking arrangement and lock. [without chamber] For Ground Floor

Item No. 53 :- Providing and fixing screw down for 15 millimeter diameter wheeled stop tap of brass including necessary sockets/union nut complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 54 :- Providing and fixing screw down for 20 millimeter diameter wheeled stop tap of brass including necessary sockets/union nut complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 55 :- Providing and fixing screw down for 25 millimeter diameter wheeled stop tap of brass including necessary sockets/union nut complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 56 :- Providing and fixing screw down for 32 millimeter diameter wheeled stop tap of brass including necessary sockets/union nut complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 57 :- Providing and fixing screw down for 50 millimeter diameter wheeled stop tap of brass including necessary sockets/union nut complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 58 :- Providing and fixing European type wall-hung white water closet of approved make with push valve concealed type with cover plate 32 millimeter size of approved make including soil pipe, vent pipe up to outside face of wall ,100mm dia. G.I. plug bend inlet pipe all fittings, cuttingand making good walls, floors etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 59 :- Providing and fixing orissa type colour glazed earthenware 625 x 450 Millimeter water clost pan including trap, C.I. soil and vent pipe upto the out side face of wall including 100 millimeter diameter C.I. plug, bend, 15mm. thick 10 litre PVC flushing cistern with all necessary pipe connection etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 60 :- Providing and fixing H.D.P container one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres J) Eighth Floor

Item No. 61 :- Providing and fixing P.V.C. Rain water pipes of 160mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and One Number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. For Ground Floor

Item No. 62 :- Providing and fixing Glass self 125 mm wide and 600 mm long with necessary chromium plated brackets providing T.W.gutties etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 63 :- Providing and fixing chromium plated towel rod 16 millimeter diameter and 75 centimeter in length including all accessories complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 64 :- Providing and fixing 10 centimeter Cast Iron Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 65 :-Providing and fixing C.P. Angular stop clock with wall flange of approved make continental including necessary sockets/union nut etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 66 :- Providing and fixing C.P. 2 Way BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 67 :- Providing and fixing C.P. pillar cock long neck with aerator of approed make including necessary sockets/union nut etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 68 :- Providing and fixing Aqual ISI marked Hands Spray including necessary sockets/union nut etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 69 :- Providing and fixing Soap dish of ess-ess make S.S. 304 quality or equivalent make as approved by the Architect or the Engineer in Charge, Including all necessary fittings etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 70 :- Providing and fixing oval type under counter wash hand basin of 16 inch x 22 inch size and of special colour shade having telephonic black / coloured granite of 180 mm thick stone black kadappa framework including chromium plated coupling bottle - Trap using CERA company or equivalent oval typa wash basin model no 3448 as per detailed drawing or as directed by engg incharge etc complete. (Counter size 1.20 m x 0.60 m )

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 71 :- Providing and fixing 450 millimeter x 550 millimeter size superior type Belgium mirror with 16 millimeter diameter nickel plated towel rod etc. complete.

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 72 :- Providing and applying interior wall finish luster of approved make on internal wall surface as detailed below Scrapping the surface with emery paper and wipe clean wall primer with brush with mineral turpentine with brush 8 to 10% and oil 15 to 20% with roller and allowing to dry for a period 6 to 8 hours. wall putty with appropriate proportion of water allowing to dry for period 4 to 6 hours. Scrapping with Emery paper 180 and wipe clean. Applyingwall primer with brush with mineral turpentine 8 to 10% and oil 15 to 20% with roller Scrapping Emery paper 320 and wipe clean, interior wall finish luster 1st coat with brush/rubber/spray with mineral turpentine 7 to 9% and Oil with roller 19 to 21% After 8 hours of activity Applying 2nd coat or wall finish Lustre with mineral turpentine 7 to 9 % with brush and Oil with roller 19 to 21% after allowing dry for the period of 6 to 8 hours activity. (With prior approval of S.E.)

A) For Basement

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 73 :- Providing and Fixing Door Shutter 35 mm thk. with glass & lock finished using 19mm plywood 303 bwr full red core with test report for shutter frame work covered with 9mm plywood 303 bwr with test report including 40 milimeter x 15 milimeter Teak Wood moulding. External side to be finished with 4 milimeter thick Venner with 6 milimeter horizontal groove with brass hinges, lock, fittings etc. complete. (without door frame)

A) For Basement

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 74 :- Providing and fixing factory made door/Window frames of required colour made with wood Polymer composite (WPC) extuded internal ribbed sections conforming to American Society for testing and materials (ASTM) in regard with density, tensile strength, flexural strength, Izod impact, water absorption and screw withdrawal strength with wall thickness of 5mm (+/1mm) and with frames having mitred joints at each corner, joined together by two nos. of 10 x 8 mm & 40 mm long PVC dovetail keys including hard wood piece support along the full vertical and horizontal length in rebate portion hole for fixing hinges and fixtures and the frames fixed to Walls/columns with 15 mm long dash fasteners/holdfasts (dash fasteners/holdfasts to be paid separately) etc. complete as per the direction of Engineer in charge,with prior approval of concerned Superitending Engineer. For Profile size of 120 x 50 mm with 32 x 12 mm double rebate (Window Section)

A) For Basement

B) For Ground Floor

C) For First Floor

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

Item No. 75 :- Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness or Tape Grooves 35 to 45 mm thickness or as required, in all position including preparing the surface, scaffolding etc. complete.

A) For Basement

B) For Ground Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

K) For Terrace Floor

Item No. 76 :- Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete.

A) For Basement

B) For Ground Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

J) For Eighth Floor

K) For Terrace Floor

Item No. 77 :-Providing and fixing mild steel grill gate with angle iron frame 65 millimeter x 65 millimeter x 10 millimeter with iron bars at 150 millimeter C/C and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coats of approved shade Weight of gate 35 Kilogram/Smt. For Ground Floor

Item No. 78 :- Finishing upto 225 mm thick cement concrete laid to proper level and slope including compacting finishing with tremix treatment for paving slab with compaction by screed vibrator , removing excess water from the cement concrete by tremix vaccum dewatering system , finishing the surface with floater and trowel including all etc. complete as directed

A) For Basement

B) For Ground Floor

Item No. 79 :- Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 450 millimeter diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete. For Ground Floor

Item No. 80 :- Providing and constructing Brick Masonry Inspection Chamber 90 centimeter x 45 centimeter x 90 centimeter including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and C.I. lid cover of 75 kg with lid and frame fixed in cement concrete. For Ground Floor

Item No. 81 :- Providing and fixing GRC Vertical plank size 4000mm X 600mm X 100mm type design having spacing in between planks 600mm c/c as per elevation design shown in drawing and as per instruction given by engineer in charge etc. complete.

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

I) For Seventh Floor

Item No. 82 :- Providing,aupplying,fabricating and fixing panel of aluminium composite panel cladding in approved shape made out of 4 mm thick ACP sheet material consisting of 3mm thick FR grade mineral core following NBC part IV Fire and life safety (having 2 hours fire resistance in accordance to ASTM E119-12 and BS476 part 6 and 7 class O) sandwitched between two aluminium sheets (each 0.5 mm thick of AA 5005/AA3105 grade) The aluminium composite panel cladding sheet shall be coil coated with kynar 500 based PVDF/Lumiflon based fluropolymer resin (having 70:30 ratio of PVDF and acrylic) coating of approved colour and sg=hade on top face and polymer (service) coating of bottom face as specified using stainless steel screws,nuts,bolts,washers,cleats,weather silicon sealent,backer rods etc .overall weight of the ACP shall not be less than 7.5 Kilogram/ One Square Metre)

D) For Second Floor

E) For Third Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

I) For Seventh Floor

Item No. 83 :- Providing structural steel work of rectangular hollow steel section for steel trusses, other similar trussed items like purlin and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted/bolted/ welded connections and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade complete.

B) For Ground Floor

C) For First Floor

F) For Fourth Floor

G) For Fifth Floor

H) For Sixth Floor

Item No. 84 :- Providing soak pit of size 120 centimeter x 120 centimeter x 120 centimeter including excavating and filling with brick-bats. For Ground Floor

Item No. 85 :- Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 Square Metre /Kilogram with two coat using approved chemicals for masonry and concrete surface by brush covering 7 years guarantee on Stamp Papers etc. complete. For Basement

Item No. 86 :- Providing and fixing 20 to 25 mm thick rough shahabad box type waterproofing treatment to vertical outside faces of Reinforced Cement concrete walls of basement or underground floor including filling the gap of 25 mm between rough shahabad and R.C.C. walls with cement grout mixed with water proofing liquid Algae proof or other alike with one tile lift method, brushing the joints horizontally with cement slurry mixed with water proofing liquid for width 30 to 35 mm and sloping coping over topmost tile with cement mortar 1:3, butting the bottom most with Cement concrete 1:2:4 mixed with water proofing liquid, curing, with 7 years guarantee on court fee stamp of Rs.100/- with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete) For Basement

Item No. 87 :- Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 0.00 to 1.50 metre) By Manual Means

Item No. 88 :- Providing and laying Cast in situ/Ready Mixcement concrete in M-20 of trap metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No.89 :- Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No. 90 :- Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork,cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No. 91 :- Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No. 92 :- Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Item No. 93 :- Providing and constructing laterite stone masonry in cement mortar 1:6 in superstructure including raking out joints when plastering is to be done/striking joints when no plastering is to be done, watering and scaffolding with all leads and lifts etc. complete.

Item No. 94 :- Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 millimeter thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 millimeter thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Item No. 95 :- Providing and fixing mild steel grill railing weighing 20 Kilogram/ One Square Metre. with PVC handrail cover and newel post for staircases, including fabricating, fixtures, drilling holes in concrete / other surface, erecting the grill work, necessary welding, fixing by nuts and bolts, fixing PVC handrail cover, with one coat of anticorrosive paint and two coats of oil painting with approved colour and shade, remaking the damaged surface, cleaning, etc. complete.

Item No. 96 :- Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete.

Item No. 97 :-Providing and fixing mild steel grill gate with angle iron frame 65 millimeter x 65 millimeter x 10 millimeter with iron bars at 150 millimeter C/C and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coats of approved shade Weight of gate 35 Kilogram/Smt.

Item No. 98 :- Supplying 60 milimeter laterite stone metal at the road side including conveying and stacking etc. with all leads and lifts etc. complete.

Item No. 99 :- Supplying 60 milimeter laterite stone metal at the road side including conveying and stacking etc. with all leads and lifts etc. complete.

Item No.100 :- Supplying hard murum/ kankar at the road site, including conveying and stacking complete.

Item No. 101 :- Spreading hard murum/ soft murrum/ gravel or kankar for side width complete.

Item No.102 :- Compacting for 80 millimeter laterite metal with power roller including necessary labour materials and artifical watering etc. complete.

Item No.103 :- Compacting for 60 millimeter laterite metal with power roller including necessary labour materials and artifical watering etc. complete.

Item No. 104 :- Compacting the hard murum side widths including laying in layers on each side with power roller including artificial watering etc. complete.

Item No.105 :- Providing and constructing 50 millimeter thick Modified Penetration Macadam (MPM) road surface including all materials, preparing the existing road surface, spreading 40mm. stone layers metal 30% crusher broken metal + 70% Hand broken metal (By breaking Rubble obtained by blasting) , heating and spraying the bitumen of specified grade @ 1.75 kg / sqm, spreading 12mm.size chips compacting with Static roller having weight 8 to 10 MT. to achive the desired degree of compaction as per Technical Specification Clause 506 etc.complete, including applying tack coat of bitumen 0f specified grade at the rate of 0.30 Kg Sqm.(on existing bitumen surface.)

Item No.106 :- Providing 20 millimeter thick premix bituminous carpet including supplying all materials, preparing and cleaning the base, heating bitumen applying tack coat at specified rate, Mixing hot bitumen and chips, laying the carpet layer and competing etc. complete. By Bulk Asphalt. (including Tack coat.) with VG-60/70 grade of bitumen.

Item No.107 :- Providing bituminous Type A liquid seal coat on bituminous surface including supplying all materials and bitumen of VG-30 grade preparing existing road surface, heating and applying bitumen @ 0.98 Kilograme per square metre by mechanical means, spreading chips and rolling, by static roller having weight 8 to 10 Metric Tonne etc. complete.

Item No. 108 :- Providing, fabricating and erecting at site of work the tubular steel structure (shed) as per standard design and specifications having various spans in between trusses and in multiples of standard length of bays as specified as per standard specifications, inclusive of cost of steel tubular trusses, tubular columns purlins, tie runners, foundation bolts, base plates, nuts and bolts, welding wherever required etc. as per detailed drawing inclusive of one coat of anticorrosive paint and two coats of oil painting of approved quality and shade etc. complete.

Item No. 109 :- Providing and fixing colour coated Zincalume ( R ) AZ150 ( min 150 gms/sq.mt. total on each side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness ( BMT ) (0.5 mm TCT ), Hi-strength steel with min.550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium 43.4% zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyester paint coat ( with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050 mm effective cover width and nominal 25-30 mm deep ribs with subtle square fluting in the five pan at nominal 180-250 mm center- to-center. The end rib shall be designed for anti-capillary groove. and return leg. The feed material should have coil manufacturers product details marked a regular interval. Including fasteners with min. fastened with min. 25 um Zinc-Tin alloy coated, Hex head, self-drilling screw etc. complete. (weight of profile 4.52 Kilogram/ One Square Metre)

Item No.110 :- Providing and Laying hot applied thermoplastic road marking strip on Bituminous Surface of specified shade/ colour of 2.5 mm thick including 1.5 Refractive index reflectorizing glass beads @ 250gm/sqm .Thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC 35:2015. Initial Dry reflectivity RL shall be > 250 mcd/sqm/lux measured in the initial 7 days and sustained reflectivity RL of 100 mcd/sqm/ lux and Qd of 100 mcd/sqm/ lux measured at the end of 2 years by means of a Standard Reflectometer of Zehntner, Easylux, Delta make capable of measuring RL & QD both according to IRC 35:2015 clause 15.5. The finished surface to be level, uniform, and free from streaks and holes complete as per direction of Engineer-in-charge and in accordance with applicable specifications.(Refer MORTH Clause 803 for technical Specification and Performance for IRC 35:2015).

Item No. 111 :- Providing and casting in situ or precast tapering R.C.C. M-20 Mountable type Kerb without gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant

Item No. 112 :- Providing & fixing 75milimetre thick Partition with Laminate & Glass finished using 18milimetre thick IS:710 grade plywood confirming to ISI 710 for frame work fixed to wall, floor & slab with vertical & horizontal supports & covered with 12 mm thk. IS:710 grade plywood confirming to ISI 710 finished with 1 mm thk. laminate confirming to IS 2046 from both side including 12 mm thk. clear glass where necessary as per design and finished. etc. (All Floors )

Item No. 113 :- Providing & fixing 75 millimeter thick Partition with Veneer & Glass finished using 18 millimeter thick IS:710 grade plywood confirming to IS 710 for frame work fixed to wall, floor & slab with vertical & horizontal supports & covered with 12 millimeter thick IS:710 grade plywood confirming to IS 710 from both sides and finished with 4 millimeter thick Veneer from both side and 12 millimeter thick glass as per design and finished.etc .(All Floors )

Item No. 114 :- Providing and Fixing Door panelling with frame, glass & round lock finished using 18 milimeter thick ply IS:710 grade plywood confirming to IS 710 for vertical supports and frame work covered with 6 milimeter thick ply IS:710 grade plywood confirming to IS 710 including 32 milimeter thick flush door with 8 milimeter thick clear glass fixed with 40 milimeter x 6 milimeter Teak Wood moulding. External side to be finished with 1 milimeter thick laminate with 6 milimiter horizontal groove with brass hinges, round lock, door closer, fittings etc. complete. (All Floors )

Item No. 115 :- Providing and Fixing Door panelling with using 18 milimeter thick IS:710 grade plywood confirnming to IS 710 for vertical supports and covered with 12 milimeter thick IS:710 grade plywood confirnming to IS 710 for frame also including 8 milimeter thick clear glass fixed 40 milimeter x15 milimeter Teak Wood moulding. External side to be finished with 4 milimeter thick veneer with 4 milimiter thick vinerwith brass hinges, round lock, door closer, fittings etc. complete. (All Floors )

Item No. 116 :- Providing & fixing large height file storage cupboard by 18 millimeter thick ply IS:710 for top, verticals, horizontals supports, shutters and 12 millimeter thick ply IS:710 for back side & 25 x 15 mm Teak wood leaping for grooves for hinges and external plywood finished with 1 millimeter thick laminate and internal with french polish, melamine polish respectively finished with brass hinges, screwes, handles, locks as per detail dwg. etc. complete. (All Floors )

Item No. 117 :- Providing & fixing large height file storage cupboard with glass shutters by 18 millimeter thick ply IS:710 of approved make for top, verticals, horizontals supports, shutters and 12 millimeter thick ply IS:710 for back side & 25 x 12 mm Teak wood leaping for grooves for hinges and external plywood finished with 4 millimeter thick venner, 8 mm thick clear glass for shutter fixed and internal with french polish & external with melamine polish finished with brass hinges, screwes, handles, locks as per detail dwg. etc. complete. (All Floors )

Item No. 118 :- Providing & fixing side storage unit using 18 milimeter thick and 12 milimeter thick ply IS:710 grade plywood confirming to IS 710 at top,bottom,side,drawers & shutters also & T.W. lipping on edges. exposed faces to bo finished with 1 mm thk. Laminate cofirming to IS:2046 and internal surfaces with Melamine polish. Including all neccessary hardwares such as ss hinges,telescopic channels, handles, locks, etc. complete (All Floors )

Item No. 119 :- Providing & fixing side storage unit using 18 milimeter thick ply IS:710 grade plywood confirming to IS 710 at top, bottom, side, drawers & shutters also & T.W. lipping on edges. exposed faces to bo finished with 4 milimeter thick Venner and internal surfaces with Melamine polishing. Including all neccessary hardwares such as ss hinges, telescopic channels, handles, locks, etc. complete. (All Floors )

Item No. 120 :- Providing and fixing Executive Table of approved size made of 18 milimeter thick ply IS:710 grade plywood confirming to IS 710 for vertical supports & top & 12 milimiter thick ply IS:710 grade plywood confirming to IS 710 extra for design with teak wood moulding at edges and front. Providing 1 milimeter thick texture laminate on all exposed surfaces & 12 milimeter thick clear glass top with fittings. Melamine polish to teak wood molding & Internal surfaces finished etc complete. (All Floors )

Item No. 121 :- Providing and fixing Executive Table of approved size made of 18 milimeter thick ply IS:710 grade plywood confirming to IS 710 for vertical supports & top & 12 milimiter thick ply IS:710 grade plywood confirming to IS 710 extra for design with teak wood moulding at edges and front. Providing 4 milimeter thick venner on all exposed surfaces & glass top with fittings. Melamine polish to teak wood molding & Internal surfaces finished etc. complete. (All Floors )

Item No. 122 :- Providing & fixing Computer table using 18 milimeter thick ply IS:710 grade plywood confirming to IS 710 for top, vertical supports and top, keyboard drawer is made by using 12 milimeter thick ply IS:710 grade plywood confirming to IS 710 and telescopic channels on side, external surface is to be finished with 1 mm thk laminate with 6 mm horizontal groove including 25 x12 mm leaping 50x 50mm teak wood mouldingand necessary fittings etc. completed. (All Floors)

Item No. 123 :- Providing and fixing Center table & Side Table using 18 milimeter thick plywood IS:710 grade plywood confirming to IS 710 for vertical supports and frame and using 12 milimeter thick glass fixed on S.S. glass stud for tops. External side to be finished with 4mm thk Venner etc. completed. (All Floors )

Item No. 124 :- Providing and fixing Wall panelling with Laminate using 18 milimeter thick ply IS:710 grade .plywood confirming to IS 710 for vertical supports of size 50 milimetre x 50 milimetre and covered with 12 milimeter thick ply IS:710 grade .plywood confirming to IS 710 & external side to be finished with 1 milimeter thick Laminate with T.W. beading groove and completed as per detail drawing. (All Floors )

Item No. 125 :- Providing and fixing Wall panelling with Venner using 18 milimeter thick ply IS:710 grade .plywood confirming to IS 710 for vertical supports of size 50 milimetre x 50 milimetre and covered with 12 milimeter thick ply IS:710 grade .plywood confirming to IS 710 & external side to be finished with 4 milimeter thick Venner with T.W. beading groove and completed as per detail drawing. (All Floors )

Item No. 126 :- Providing and fixing Wall panelling with Acrylic Solid Surfaces (L.G./Euro/Solido) make using 18 milimeter thick ply IS:710 grade .plywood confirming to IS 710 for vertical supports of size 50 milimetre x 50 milimetre and covered with 12 milimeter thick ply IS:710 grade .plywood confirming to IS 710 & external side to be finished with 6mm thick Acrylic Solid Surfaces using arcylic adhesives for pasting on it with approved color and design which can be cut, shape, mould and thermoformed into required shape & size and completed as per detail drawing. (All Floors )

Item No. 127 :- Providing and fixing Wall panelling using 18 milimeter thick ply IS:710 grade .plywood confirming to IS 710 for vertical supports of size 75 milimetre x 45milimetre and covered with 12 milimeter thick ply IS:710 grade plywood confirming to IS 710 & external side to be finished with 6mm thk. Mirror with 25mm x 15mm teak wood molding etc completed as per detail drawing. (All Floors )

Item No. 128 :- Kitchen Trolley Providing and Fixing stainless steel kitchen trolley of overall 26" height and 22"depth, supported on aluminium pipes, trolley basket made out of 5mm stainless steel rod fitted on telescopic channel of size 1.5"x20"x22" on both sides of trolley of 12" or above size, panel having 40Kilogram load bearing capacity of trolley made out of 20mm PUC coated plywood and colour combination as directed by E-I-C.Inner side of panel covered by white mica,100 mms.s. decorative handle .(The width and height of individual compartments shall be kept as directed by Engineer-in-charge)

Item No. 129 :- Providing and fixing Executive Chairs of full height push back and revolving seat with hydraulic adjestment and wheels made of cottton fabric finished & fiberour foam handle & finished complete.

Item No. 130 :- Providing and fixing Officer's chair of low height push back and revolving seat with hydraulic adjestment and wheels made of cotton fabric finished and fiberour foam handle and finished etc. complete.

Item No. 131 :- Providing and fixing Computer Operater's chair ofof low height push back and revolving seat with hydraulic adjestment and wheels made of cotton fabric finished and fiberour foam handle and finished etc. complete.

Item No. 132 :- Providing and supplying Visitor Chair of fix back and seat made of composite leather coushoning and fibour foam handles fixed on stainless steel frame of 45 mm x 45 mm pipe and finished etc. complete.

Item No. 133 :- Providing and fixing Zebra Blinds for windows finished and complete as per design. (All Floors )

Item No. 134 :- Providing and fixing Plated Roller Blinds for windows finished and complete as per design. (All Floors )

Item No. 135 :- Providing and supplying Sofa set with wooden frame Work and 75mm nylon spring patti with 50 density super soft 'U' foam covered with shunnile cloth of décor company make as per design & shade etc.complete (All Floors ) (WAITING)

Item No. 136 :- Providing and supplying Sofa set with wooden frame Work and 75mm nylon spring patti with 50 density super soft 'U' foam covered with shunnile cloth of décor company make as per design & shade etc.complete (All Floors ) (VIP SOFA)

Item No. 137 :- Providing and fixing Meeting Table of approved size made of 18 milimeter thick ply IS:710 grade plywood confirming to IS 710 for vertical supports & top & 12 milimeter thick ply IS:710 grade plywood confirming to IS 710 for front with teak wood moulding at edges and front. Providing 6 milimeter thick Acrylic Solid Surfaces on all exposed surfaces, Melamine polish to teak wood moulding to internal surfaces as per Design etc complete. (All Floors )

Item No. 138 :- Public Seating Chair. - 3 Seater Providing and Fixing 3 seater Public seating chair made of complete metal with Legsin Crome finish and seates in silver powder coating finish.

Item No. 139 :- Providing & Fixing name board of unbreakable acrylic sheet 4mm thk. maximum sixe 450 x 230 including computerrized vinly letters (only designation in marathi) as per drawing etc., complete

Item No. 140 :- Providing & Fixing notice board of maximum size of 1800 X 1200mm made out of 6 mm thk foam with compuret etc., complete

Item No. 141 :- Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 0.00 to 1.50 metre) By Manual Means

Item No. 142 :- Excavation for foundation in laterite rock (soft or hard) including trimming and levelling the bed for the foundation, removing the excavated material up to a distance of 50 metres beyond the building area, stacking as directed, dewatering and back filling with available murum, watering, ramming etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Item No. 143 :- Providing and constructing laterite stone masonry in cement mortar 1:6 in Foundation and plainth including raking out joints whhen plastering is to be done/Striking joints when no plastering is to done, wateringand scaffolding with all leads and lifts etc. complete.

Item No. 144 :- Garden Soil- Supplying on site garden soil well sieved 90% to pass through I.S. sieve of 10mm size from stones rubbish like dried grass roots and other such materials. The soil should be fresh from quarry, The colour of the soil generally be red. The soil will be measured by measuring box (Farma) (Item includes Royalty charges corpration tax transporting loading unloading etc.)

Item No. 145 :- Filling fresh garden, soil/silt and manure in excavated area including lead upto distance of 50 mtrs, (1/10 of unskilled labour)

Item No. 146 :- Supplying & laying ready to fix lawn turf in slab or rolls etc complete.

Item No. 147 :- Supplying & laying ready to fix Plant, etc complete.

Tree (Bid)

A) Bahawa tree

B) Largerstromia

C) Pistal Palm

D) Ficus Benjamina

E) Ficus Panda

F) Kanchan Tree

G) Sita Ashoka

H) Chafa (Gophted)

I) Saptparni

Tree (Medium)

A) Tekoma Stans

B) Tekoma Capensis

C) Allamanda Silver

Tree (Medium)

A) Himalaya Pentas

B) Bamboo Grass

C) Golden Duranta

D) Duranta Verigated

E) Kanher

F) Kardal

G) Spider Lily

H) Ixora

I) Song of India

J) Ribbon Grass

Item No. 148 :- Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 0.00 to 1.50 metre) By Manual Means

Item No. 149 :- Providing soling using 80 millimeter size trap metal in 15 centimeter. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete.

Item No. 150 :- Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Item No. 151 :- Providing and fixing 100 millimeter diameter stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete

Item No. 152 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-15 of trap metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No. 153 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No. 154 :- Providing and laying cement concrete flooring 40 mm thick with M15 cement concrete laid to proper level and slope in alternate bays including compaction, filling joints, marking lines to give the appearance of tiles of 30 cm x 30 cm or other size laid diagonally /square etc finishing smooth (with extra cement) in any colour as directed and curing etc. complete.with Crushed sand VSI Grade

Item No.155 :- Supplying and erecting 20mm dia. corrugated flexible polypropylene conduit

Item No.156 :- Supplying and erecting 25 mm dia. corrugated flexible polypropylene conduit

Item No.157 :- Supplying and erecting HMS PVC conduit FRLS grade 20 mm dia. with PVC accessories on wall / ceiling as per specification No: WG-MA/CON.

Item No.158 :- Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. with PVC accessories on wall /ceiling as per specification No: WG-MA/CON.

Item No.159 :- Supplying and erecting HMS PVC conduit FRLS grade 32 mm dia. with PVC accessories on wall / ceiling as per specification No: WG-MA/CON.

Item No.160 :- Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25 mm with accessories on wall/ceiling as per specification No: WG-MA/CON

Item No.161 :- Supplying and erecting PVC trunking (PVC casing-n-capping) of size 32 mm with accessories on wall/ceiling as per specification No: WG-MA/CON

Item No.162 :- Supplying and erecting PVC trunking (PVC casing-n-capping) of size 40 mm with accessories on wall/ceiling as per specification No: WG-MA/CON

Item No.163 :- Supplying and erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Item No.164 :- Supplying and erecting mains with 1x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Item No.165 :- Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.166 :- Supplying and erecting mains with 1x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.167 :- Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.168 :- Supplying and erecting mains with 1x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.169 :- Supplying & erecting mains with 1x6sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Item No.170 :- Supplying and erecting mains with 2x6 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Item No.171 :- Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete

Item No.172 :- Supplying and erecting ISI mark modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Item No.173 :- Supplying and erecting ISI mark modular type 3 pin 6A multi sockets with safety shutter, duly erected on provided plate and box with wiring connections complete.

Item No.174 :- Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Item No.175 :- Supplying and erecting modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete.

Item No.176 :- Supplying and erecting modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

Item No.177 :- Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Item No.178 :- Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background

Item No.179 :- Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Item No.180 :- Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Item No.181 :- Point wiring for light/bell hybrid type (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/HW

Item No.182 :- Point wiring for ceiling fan (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/HW

Item No.183 :- Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Item No.184 :- Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Item No.185 :- Wiring for plug on board with Switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification No: WG-PW/CW

Item No.186 :- Supplying & erecting 2 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, Nylon Rip Cord & grey colour sheathed with FR PVC, conforming to ITD specification S/WS 113C laid in provided PVC casing capping/conduit as per specification No. WG-TW

Item No.187 :- Supplying & erecting 20 pair, 0.5mm dia, jelly filled unarmoured telephone copper cable with poly-al laminate moisture barrier, laid in provided PVC casing capping/conduit as per specification No. WG-TW

Item No.188 :- Supplying, erecting & commissioning 20 pairs FR junction box with moulded plastic enclosure as per specification no. WG-TW

Item No.189 :- Supplying, installing, testing & commissioning digital (hybrid) type EPABX of 6 x 16 extension complete.

Item No.190 :- Supplying, installing, testing & commissioning push button telephone instrument desk top/wall mount with caller ID & Speaker unit as per specification complete.

Item No.191 :- Supplying and installing cat-6 cable suitable for networking as per specification no. WG-COC/NC

Item No.192 :- Supplying and fixing 1 m UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Item No.193 :- Supplying and fixing 3 m UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Item No.194 :- Supplying, fixing, and configuring 24 ports with 4 (SFP+) port, ethernet managed switch with web view/CLI, 6KV surge protection on ethernet port and console port for management in provided rack as per specification no. WG-NWC/GBS

Item No.195 :- Supplying, fixing, and configuring broadband ADSL router with all accessories, on provided rack as per specification No. WG-NWC/ADSL

Item No.196 :- Supplying, installing and testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC.

Item No.197 :- Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO

Item No.198 :- Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP

Item No.199 :- Supplying and fixing 6U wall mount rack (Dimension-DxWxH – 500x600x367 mm) as per specification No. WG-NAS/RAK

Item No.200 :- Supplying and erecting LED square / circular Max. 14 W down lighter/Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1500 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Item No.201 :- Supplying and erecting LED square / circular Max. 18 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Item No.202 :- Supplying and erecting bulk head LED fitting max. 10W with high transitivity diffuser with system lumens output of min. 1100 lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., THD<10%, p.f. >0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, IP66, IK09 rated on provided PVC Block / wooden board with 3 years warranty.

Item No.203 :- Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Item No.204 :- Supplying and erecting Ding Dong / electronic musical type call bell with heavy duty coil suitable to operate on 230V A.C. supply erected on polished double wooden /sunmica block of suitable size

Item No.205 :- Supplying and erecting integrated LED flood light fitting Max. 120W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min.14500 Lumens, min. efficacy of 120 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver with U shaped bracket with 3 Years warranty as per specification No FG-ODF/FLS2.

Item No.206 :- Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and ‘E’ class insulation.

Item No.207 :- Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm, max. energy consumption of 28W having service ratio (CMM/W) of Min. 8 , PF>0.9, THD<10% with IR remote control/compatible speed regulator, Temperature Rise of Max. 40 deg. C, having external mounted control PCB completely erected in position as per specification no. FG-FN/CF

Item No.208 :- Supplying and erecting fan hook of 10 mm. M.S. round bar grouted in RCC slab with making the site as original.

Item No.209 :- Supplying and erecting ‘B’ grade G.I. pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire.

Item No.210 :- Supplying, erecting, testing and commissioning self contained water cooler 230/250V 50Hz nominal cooling capacity of 150 litres per hour and storage capacity 150 litres with partially stainless steel body as per specification no. AP-WCR/WC

Item No.211 :- Supplying and erecting ultra violet storage type water purifier (RO+UV+UF) with softener for safe drinking water consisting of UV germicidal tube of 8W capacity choke made of copper wire and two indicator lamps with output of purified water minimum 0.33 litre/min with activated carbon filter and softener operating on 230V, single phase A.C. supply with UV fail & filter change indication system .(for TDS more than 200)

Item No.212 :- Supplying, installing, testing and commissioning of single phase, 230V, 50 Hz, 1400 to 1600 VA digital pure sine wave inverter with backup time of 04 hrs. based on Insulated Gate Bipolar Transistor (IGBT) technology complete as per specification no. AP-INV

Item No.213 :- Supplying and erecting 12V/150Ah tubular battery with battery terminal wire, duly charged with 36 months warranty complete.

Item No.214 :- Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 12 mm for solar water heater/AC system.

Item No.215 :- Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for over coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 16 mm for solar water heater system.

Item No.216 :- Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification No. SW-SWR/MCB

Item No.217 :- Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification No. SW-SWR/MCB

Item No.218 :- Supplying, erecting & marking DPMCB 40A to 63A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Item No.219 :- Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Item No.220 :- Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 4 ways/phase (12 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Item No.221 :- Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/ flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Item No.222 :- Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Item No.223 :- Supplying, erecting & commissioning 2 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Item No.224 :- Supplying, erecting & commissioning 4 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Item No.225 :- Supplying and erecting marine (Waterproof) plywood 18/19 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners, supports, nut bolts etc. complete with compliance to IS 720:2010

Item No.226 :- Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Item No.227 :- Supplying and erecting bus bar chamber triple pole with neutral with four copper bars, 500V 200A having 20mm (Width) X 2 mm (Thickness), with 99.9 % Copper purity as per E91E Grade & Current Density 1.6 A per sq. mm. compliance to IS 5082 and Enclosure fabricated with 16 SWG CRCA sheet and epoxy paint, with suitable number of ways and with SMC/DMC Insulators and accessories of suitable rating complete as per specification no. CP-BB

Item No.228 :- Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.229 :- Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 2 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Item No.230 :- Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Item No.231 :- Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU(DB 170+ AC 100)

Item No.232 :- Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Item No.233 :- Supplying & erecting G.I. pipe ‘A’ class 40 mm dia. erected for enclosing XLPE armoured cable on wall/pole as per specification no. CB-CE

Item No.234 :- Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 100 mm height comprising all required standard accessories.

Item No.235 :- Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 200 mm width & 100 mm height comprising all required standard accessories.

Item No.236 :- Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 100 mm height comprising all required standard accessories.

Item No.237 :- Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 500 mm width & 100 mm height comprising all required standard accessories.

Item No.238 :- Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP( Lift- 6, LA-6)

Item No.239 :- Supplying, installation and testing of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the results Specification no. EA-MOBI( For Panel 5x2)

Item No.240 :- Supplying and erecting copper strip of high purity required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint with joints required. As per specification no. EA-EP.(220 Mtrx0.670)

Item No.241 :- Supplying & erecting conventional spike type air termination suitable to carry lightning stroke made up of heavy gauge 40 mm dia copper pipe of standard length with 5 Nos. copper spikes fixed on copper ball as air terminals duly threaded in copper pipe erected on provided foundation complete.

Item No.242 :- Supplying and fixing PVC synthetic elastomer electrically insulating mat with class A insulation conforming to IS: 15652 – 2006 having 2 mm thickness up to 3.3 kV

Item No.243 :- Supply,Installation,Testing and Commissioning of 100mm X40 mm GI underfloor raceway with cover box thichnesss of 1.6mm. comprising all required standard accessories. Non Csr Rate approved by Suprintending Enginneer Electrical Mumbai vide Letter No 85 dated 11.01.2023

Item No.244 :- Providing & fixing floor junction box having size of 255x255mm & height of 60mm complete made up of G.l sheet of l.2mm thick with SS 304 grade cover of size 260x260mm and 3mm thick power coated finish for having arrangement of incoming and outgoing of PVC/GI pipes/truncking.. Non Csr Rate approved by Suprintending Enginneer Electrical Mumbai vide Letter No 85 dated 11.01.2023

Item No.245 :- Supplying, erecting, testing & commissioning of Cubical control panel of cubical construction, floor mounted type, fabricated from minimum 2 mm thick CRCA sheet, compartmentalised with hinged lockable doors, with enclosure protection class IP54, duly powder coated or painted with accessories duly painted with two coats of synthetic enamel paint of enamal colour over a coat of primer (ISC code 536 as per IS 2932 of 2003), cable alley, interconnection with suitable size solid copper busbar strip of adequate size for all power connections having switchgears and accessories, mountings and internal wiring with adequate size copper conductor cable, earth terminals, numbering etc. complete in all respect, suitable for satisfactory operation with necessary accessories, wiring & cabling along with allied accessories with following incoming and outgoings, suitable for automatic & manual operation on 415V, 3 phase, 50Hz ac supply as per specifications following features & switchgears: 1. Main incomer FP 400A MCCB having rotary handle 2. Outgoing FP 250A MCCB having rotary handle 3. Outgoing FP 100A MCCB having rotary handle 3. Outgoing FP MCB 63 A 4. Outgoing FP MCB 40 A 5.Outgoing DP MCB 40 A

Item No.246 :- Main Fire Pump (13.1.5) Supplying, installation, testing and commissioning of main fire pump (MFP / EP) suitable for water discharge of 2280 to 2850 LPM at 90 to 70 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 55kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal type, single stage, centrifugal/split casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation on with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/EP

Item No.247 :- Diesel fire Pump (13.4.2) Supplying, installation, testing and commissioning of main fire pump (MFP/DP) suitable for water discharge of 2280 to 2850 LPM at 90 to 60 m head driven by 76 HP or suitable HP capacity diesel engine at required working speed suitable for manual/automatic operation and consisting of following : (a) Horizontal type, single stage, centrifugal casing pump of cast iron body & bronze impeller with stainless steel shaft(SS410 grade), mechanical seal conforming to IS 1520. (b) Water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12/24 volts DC electric starting equipment with battery of required AH capacity with necessary charger suitable to work on 230v, 50Hz AC supply, diesel tank of minimum 150ltr capacity with first filling of diesel up to 100% level with necessary piping with valves up to engine , exhaust pipe extended up to 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications etc. as required. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with engine assembly and accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/DP

Item No.248 :- Supplying, installation, testing and commissioning of jockey fire pump (JP) suitable for water discharge of 180 to 240 LPM at 90 to 70 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 9.3 kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal/vertical type, multi stage, centrifugal casing pump of cast iron body & bronze impeller with stainless steel shaft(SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003)complete, as per specification no. FF-MFP/JP

Item No.249 :- Fire Pump Control Panel (13.5.1) Supplying, erecting, testing & commissioning of fire pump control panel (FCP) of cubical construction, floor mounted type, fabricated from minimum 2 mm thick CRCA sheet, compartmentalised with hinged lockable doors, with enclosure protection class IP54, duly powder coated or painted with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003), cable alley, interconnection with suitable size solid copper busbar strip of adequate size for all power connections having switchgears and accessories, mountings and internal wiring with adequate size copper conductor cable, earth terminals, numbering etc. complete in all respect, suitable for satisfactory operation of main fire pump and jockey (pressurisation) pumps (1working+1standby) with necessary accessories, wiring & cabling along with allied accessories with following incoming and outgoings, suitable for automatic & manual operation on 415V, 3 phase, 50Hz ac supply as per specifications the capacity of electric motor driven pump are as follows a. Main fire pump(MFP) having capacity of 22kW 1no (1 working) b. Jockey pump(JP) capacity of suitable capacity 2 nos(1 working +1 standby, alternate run per start in auto mode) comprises of the following features & switchgears: 1. Main incomer FP SFU having rotary handle with HRC fuses of suitable rating. 2. Electrolytic grade copper strips for busbar of suitable sizes for main incomer and branches to motor SFU's, starters & outgoing terminals with necessary accessories like stainless steel nut bolts with spring washers for connections, mounted on required no of epoxy or porcelain support insulators of suitable ratings etc. 3. Individual pump TPN SFU having rotary handle with HRC fuses of suitable rating. 4. Digital voltmeter & ammeter & RYB indicating lamps & push buttons & SPP, O/L & phase reversal protection with emergency stop switch.5. TPN SPD 100kA Type 1 +2 tested.

Item No.250 :- Supplying and erecting G.I. pipe ‘C’ class ERW 200 mm dia with necessary fittings complete as per specification no. FF-PP

Item No.251 :- G.I. Pipe ERW 100 mm (13.6.6) Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP

Item No.252 :- Supplying and erecting 200 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Item No.253 :- Supplying and erecting 200 mm dia cast iron double flange ball type NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Item No.254 :- Butterfly Valve 100 mm (13.7.20) Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Item No.255 :- NRV 100 mm dia (13.7.24) Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Item No.256 :- Supplying and erecting 200 mm dia cast iron foot valve ball type/flap type with strainer for negative suction complete as per specification no. FF-VL/FV

Item No.257 :- Supplying and erecting 200 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating, as per specification no. FF-VL/SV

Item No.258 :- Supplying and erecting 300 mm dia 1.5m in height air vessel / tank fabricated from min 5mm thick M.S. sheet complete as per specification no. FF-FFA/ACT

Item No.259 :- Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG

Item No.260 :- Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PS

Item No.261 :- Cable Tray 150 mm (7.11.1) Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 100 mm height comprising all required standard accessories.

Item No.262 :- Arm. cable 3½ core 95 sq. mm. (7.1.19) Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/A

Item No.263 :- Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 50 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid

Item No.264 :- Mains 2x2.5 sq.mm (1.3.2) Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.265 :- Mains 2x1.5 sq.mm (1.3.1) Supplying and erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Item No.266 :- Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 6 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.267 :- Supplying and installing one piece moulded HDPE / fibre water tank for negative suction only, having capacity 1000 litres fitted with necessary accessories complete as per specification no. FF-FFA/PT

Item No.268 :- G.I. Pipe ERW 25 mm (13.6.2) Supplying and erecting G.I. pipe ‘C’ class ERW 25 mm dia with necessary fittings complete as per specification no. FF-PP

Item No.269 :- Gate Valve (13.7.32) Supplying and erecting 25 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV

Item No.270 :- Supplying and erecting 200 mm dia Cast Iron end line strainer of Y-type flanged end pattern, PN16 pressure rating, screen of SS end connection with Flanged / Screwed / Socket Weld / Butt Weld End etc with standard OAR (open area Ratio) for positive suction complete as per specification no. FF-VL/ELS

Item No.271 :- Iron Work (6.1.19) Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Item No.272 :- G.I. Pipe ERW 150 mm (13.6.7) Supplying and erecting G.I. pipe ‘C’ class ERW 150 mm dia with necessary fittings complete as per specification no. FF-PP

Item No.273 :- G.I. Pipe ERW 75/80 mm (13.6.5) Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings complete as per specification no. FF-PP

Item No.274 :- Providing coating of bitumen paint & 4mm thick wrapping for underground 150 mm ring main of fire fighting system.

Item No.275 :- Supplying and erecting stainless steel single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV

Item No.276 :- Supplying and erecting M.S./CRCA cabinet for housing Fire Brigade / SIEMESE connections (size 1250 x 400 x 300 mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8" x 6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)

Item No.277 :- Supplying and erecting 63mm dia, reinforced rubber lined (R.R.L.) hose pipe, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL

Item No.278 :- Supplying and erecting stainless steel branch pipe 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specifications no. FF-FFA/NZ

Item No.279 :- Supplying and erecting 150 mm dia fire brigade header suitable for supplying water in fire tank complete as per specification no. FF-FA/FBC

Item No.280 :- Butterfly Valve 150 mm (13.7.21) Supplying and erecting 150 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Item No.281 :- Supplying & erecting ABC fire extinguisher of 6 kg. capacity

Item No.282 :- Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

Item No.283 :- G.I. Pipe ERW 150 mm (13.6.7) Supplying and erecting G.I. pipe ‘C’ class ERW 150 mm dia with necessary fittings complete as per specification no. FF-PP

Item No.284 :- G.I. Pipe ERW 100 mm (13.6.6) Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP

Item No.285 :- Supplying and erecting stainless steel single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV

Item No.286 :- Supplying and erecting M.S./CRCA cabinet for housing Fire Brigade / SIEMESE connections (size 1250 x 400 x 300 mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8" x 6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)

Item No.287 :- Supplying and erecting 63mm dia, reinforced rubber lined (R.R.L.) hose pipe, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL

Item No.288 :- Supplying and erecting stainless steel branch pipe 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specifications no. FF-FFA/NZ

Item No.289 :- Supplying and erecting 150 mm dia fire brigade header suitable for supplying water in fire tank complete as per specification no. FF-FA/FBC

Item No.290 :- Supplying and installing wall mounting swinging hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) along with necessary accessories complete as per specification no. FF-FFA/HV

Item No.291 :- Butterfly Valve 150 mm (13.7.21) Supplying and erecting 150 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Item No.292 :- Butterfly Valve (13.7.20) Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Item No.293 :- NRV 100 mm dia (13.7.24) Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Item No.294 :- Supplying and erecting 100 mm dia Cast Iron end line strainer of Y-type flanged end pattern, PN16 pressure rating, SS screen, end connection with Flanged / Screwed / Socket Weld / Butt Weld End etc with standard OAR (open area Ratio) for positive suction complete as per specification no. FF-VL/ELS

Item No.295 :- Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG

Item No.296 :- Supplying and erecting 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV

Item No.297 :- Supplying, installation, testing and commissioning of booster fire pump [BP] suitable for water discharge of 450 LPM at 35 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 5.5 kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal/vertical type, single/multi stage, centrifugal casing pump of cast iron body & bronze/CI impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/BP

Item No.298 :- D.O.L Starter (12.4.2) Supplying & erecting D.O.L Starter suitable for 415 V, 3 phase 50 cycles with no volt coil and overload element with necessary materials and connected to supply up to 7.5 H.P.

Item No.299 :- Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 6 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.300 :- MCCB 03 Pole (5.5.1) Providing & erecting 3 Pole MCCB, 415 V, 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Item No.301 :- Quartzoid Bulb Sprinkler (13.12.1) Supplying, erecting, testing and commissioning of quartzoid bulb sprinkler, 15 mm (½") dia. NBCM Body chrome finished, 68º C fixed temperature rating with deflector disc of conventional construction complete as per specification no. FF-SPR.

Item No.302 :- G.I. Pipe ERW 150 mm (13.6.7) Supplying and erecting G.I. pipe ‘C’ class ERW 150 mm dia with necessary fittings complete as per specification no. FF-PP

Item No.303 :- G.I. Pipe ERW 100 mm (13.6.6) Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP

Item No.304 :- G.I. Pipe ERW 50 mm (13.6.3) Supplying and erecting G.I. pipe ‘C’ class ERW 50 mm dia with necessary fittings complete as per specification no. FF-PP

Item No.305 :- G.I. Pipe ERW 25 mm (13.6.2) Supplying and erecting G.I. pipe ‘C’ class ERW 25 mm dia with necessary fittings complete as per specification no. FF-PP

Item No.306 :- Butterfly Valve 150 mm (13.7.21) Supplying and erecting 150 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Item No.307 :- Butterfly Valve 100 mm (13.7.20) Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Item No.308 :- Butterfly Valve 50 mm (13.7.17) Supplying and erecting 50 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Item No.309 :- Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the 4 loop capacity and capable of supporting upto 250 devices and detectors per loop, with on-board LCD display with min 16 lines of text, operating at 230 V 50 HZ - AC with inbuilt Battery Backup of a minimum 24 hours in normal condition and 30 min in alarm condition, suitable provision for network connectivity, interfacing with third party equipment via a MODBUS/ OPC/ L-ON interface etc. conforming to IS 15908:2021, ,IS 2189: 2008, EN 54 & VDS / FM/ UL 864 (10th edition) with 3 years replacement warranty FF-AFAS/CP.

Item No.310 :- Supplying, installing, testing and commissioning of repeater panel with suitable battery backup of a minimum of 24 hours in normal condition and 30 min in alarm condition, 80 backlit alphanumeric LCD display with inbuilt buzzer to indicate fault/fire alarm, manual control keys for silence/mute and to reset the FACP from the repeater station. Panel size shall not more than 175 x 275 x 65 mm conforming to EN 54 or UL approved with 3 years equipment replacement warranty FF-AFAS/RP

Item No.311 :- Supplying, installing, testing and commissioning of addressable horn cum strobe sound/ hooter, output frequency 500 to 1000 Hz with dB as per Chart given in IS 15908:2021, with flashing at 1 Hz over the strobe’s entire operating voltage range EN 54, conforming to IS 2189: 2008, IS 15908:2021 standards with 3 years equipment replacement warranty FF-AFAS/SSH.

Item No.312 :- Supplying, installing, testing and commissioning of addressable horn cum strobe sound/ hooter, output frequency 500 to 1000 Hz with dB as per Chart given in IS 15908:2021, with flashing at 1 Hz over the strobe’s entire operating voltage range EN 54, conforming to IS 2189: 2008, IS 15908:2021 standards with 3 years equipment replacement warranty FF-AFAS/SSH.

Item No.313 :- Supplying, installing, testing and commissioning of addressable optical smoke detector, single/twin LED’s with 360 degree view, suitable for low voltage 15 to 32 V DC two wires supply, in-built locking mechanism to check the removal and pilferage of the detector, in built isolation mode, start up current 300µA and alarm condition current shall be maximum 6.5 mA, operating temperature 0°C to 50°C, humidity 0-95% RH, IP 41, conforming to IS 2189: 2008, 11360_1985_Reff2020 EN 54 or UL Approved with 3 years equipment replacement warranty FF-AFAS/SD .

Item No.314 :- Supplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU

Item No.315 :- Supplying, installing, testing and commissioning of addressable fire control/relay module complete as required, with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 reed relays, EN 54 or UL Listed FF-AFAS/CRM

Item No.316 :- Supplying, installing, testing and commissioning of addressable fire isolator module complete as required. EN 54 /FM or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/ISM

Item No.317 :- SMF Battery (3.8.7) Supplying and erecting 12V/7Ah -7.5Ah SMF battery with battery terminal wire, duly charged with 12 months warranty complete

Item No.318 :- POWER SUPPLY SMPS

Item No.319 :- Amplifier (13.11.1) Supplying, erecting, testing and commissioning 120 W amplifier suitable to operate on 230 Volts A.C. / 12 Volts D.C. supply complete as per specification no. FF-PA/AFR

Item No.320 :- Sound Column (13.11.2) Supplying, erecting, testing and commissioning 15 to 30 Watts sound column or ceiling mounted complete as per specification no. FF-PA/SOC

Item No.321 :- Microphone (13.11.3) Supplying, erecting, testing and commissioning stand mounted/handheld type wired microphone having 2 mV/Pa sensitivity, impedance level limit 300 ohms and 50 - 16000 Hz suitable to operate in -10 deg C to +55 deg C with min. 7 metre shielded cable and 3 Pin Professional XLR Connector, stereo jack complete as per specification no. FF-PA/MIC

Item No.322 :- Microphone Stand (13.11.4) Supplying, erecting, testing and commissioning rust free microphone floor stand of chrome plating/powder coating or S.S. material , 500 mm to 1500 mm height and sturdy mechanism ensuring trouble free movement complete.

Item No.323 :- 2 Core Shielded Cable (13.11.6) Supplying, erecting, testing and commissioning of 2 core shielded cable complete as per specification no. FF-PA/MCC

Item No.324 :- C.C. Foundation (16.3.5) Making cement concrete foundation in 1:2:4 cement concrete with foundation bolts and nuts complete. (cost of wooden box is included) (for pumps).

Item No.325 :- Providing Round bottom fire bucket of 9 Litres capacity as per IS : 2546 made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and red outside with FIRE Mark, on provided stand/ wall hook complete.

Item No.326 :- Providing Floor mounting stand for keeping 4 Nos. of FIRE buckets 1500mm in length, 900mm in height frame made out of 30x30x4 mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two coats of silver paint complete.

Item No.327 :- Core Cutting (3.11.77) Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original.

Item No.328 :- Galvanized Iron Earth Plate (9.1.3) Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover complete with all materials, testing & recording the results as per specification no. EA-EP

Item No.329 :- Supplying & Installation auto glow fire singnages, fire extinguisher, fire exist, hose box & other

Item No.330 :- SITC of Electric Traction Passenger Lift with Rated capacity :13 Passenger/884Kg Floors :- Basement + G+7 floor (9 Stops/9 Landings) ·Travel :- 4 mtrs·Location of Lift Machine:- /MRL·Rated speed :- 1.0mps VS·Car/Landing door clear opening of 900 mm wide x 2000 mm high ·Clear Car size of 1600mm wide x 1350mm deep x 2250mm high· Lift shaft available having clear size of 2500mm wide x 2100mm deep, 1500mm Pit depth, 5000mm Overhead.

Doors type :- COPO/TOPO Doors with frame made from SS 304 grade solid(non-cladded) sheet of 1.5mm thick in hairline finish for car and all landing doors with SS door architraves/frames The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory).

Lift car enclosure made from SS 304 grade solid (non-cladded) sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. The lift car interior design shall be done as per the directions of engineer in charge.

COP with SS face plate having metallic push buttons with Braille code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with / without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor.

LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings.

Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port. The controller shall have necessary protections such as overcurrent, overvoltage, over speed, overheat for all devices including lift motor and travel direction protection, protection for phase loss at input or output etc. various operation modes such as maintenance, change direction by attendant, full load bypass, VIP call operation, self levelling operation, call cancel facility, auto return to home landing, fireman evacuation operation, earthquake operation, door open/close operation from COP etc. The system can record information for minimum 30 latest faults, with real-time clock management and handheld keypad with LCD screen for view and setting of parameters, The control panel duly wired with proper size & strength, copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class. ARD complete with necessary SMF VRLA batteries. Fireman controller having fireman switch at fire Landing.

CCTV surveillance system comprises of 2 nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for min. 90 days with min. 18” FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge.

Lift Machine of Gearless PMSM of suitable kW with duty cycle of minimum 120 starts/hr (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory), with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength.

Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work.

Minor civil work such as alteration work if any necessary for erection of landing door frames and it's accessories e.g. sill, header, hole pass etc complete with plaster finish, civil work for erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails, providing and fixing steel girders/RCC work having adequate strength for mounting and hoisting lift machine etc. complete as per specification no. LFT.

General: - Job includes entire procedure of obtaining all necessary erection permissions & "License to Work the Lift" from Electrical Inspector(Lifts) with submission to the Engineer In Charge. · The above rate includes Fully Comprehensive AMC for one year from the date of commissioning.

B) For Lift having 900mm wide x 2000mm high clear entrance in 1.5mm thick SS 304 grade solid(non-cladded) landing door [Two panel], this includes all necessary accessories like LOP's with UP/DN buttons-arrows-indicators, extension of guide rails, shaft wiring with trunking, travelling cables, main hoisting ropes/belts, & OSG rope landing doors with all accessories etc. necessary for the normal safe functioning of lift installation complete

C) SITC of Duplex Lift control system for two nos. microprocessor IOT/PLC based simplex lift controllers along with necessary software with programming and hardware e.g. logic board, necessary communication/control/data cabling laying in rigid PVC conduits/trunking etc. complete

D) For additional 2MP Camera along with necessary accessories at Home Landing,

Item No.331 :- Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. with PVC accessories on wall /ceiling as per specification No: WG-MA/CON.

Item No.332 :- Supplying and erecting PVC trunking (PVC casing- n-capping) of size 25 mm with accessories on wall/ceiling as per specification No: WG-MA/CON.

Item No.333 :- Supplying and erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG- MA/BW

Item No.334 :- Supplying and erecting mains with 1x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG- MA/BW

Item No.335 :- Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.336 :- Supplying and erecting modular type switch 6A /10A duly erected on provided plate and box with wiring connections complete.

Item No.337 :- Supplying and erecting modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Item No.338 :- Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Item No.339 :- Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Item No.340 :- Wiring for plug on board with Switch socket surface /concealed type, copper wiring and earthing and with modular accessories as per specification No: WG-PW/CW

Item No.341 :- Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Item No.342 :- Point wiring for ceiling fan in PVC trunking (casing- capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG- PW/SW

Item No.343 :- Supplying and erecting bulk head LED fitting max. 10W with high transitivity diffuser with system lumens output of min. 1100 lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., THD0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, IP66, IK09 rated on provided PVC Block / wooden board with 3 years warranty.

Item No.344 :- Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 module duly erected.6, IK09 rated on provided PVC Block / wooden board with 3 years warranty.

Item No.345 :- Supplying and erecting CRCA powder coated corridor/passage light LED fitting (4 feet) Max. 17W with high transitivity diffuser with system lumens output of Min. 2000 lumens , min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Item No.346 :- Supplying and erecting fan hook of 10 mm. M.S. round bar grouted in RCC slab with making the site as original.

Item No.347 :- Supplying and erecting modular type blanking plate two module, duly erected on provided plate & box.

Item No.348 :- Supplying and erecting energy saving ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Item No.349 :- Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and ‘E’ class insulation.

Item No.350 :- Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Item No.351 :- Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 6 ways (6 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Item No.352 :- Supplying, erecting & commissioning 2 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Item No.353 :- Providing, erecting & commissioning 4 pole RCCB 63A, with added immunity to avoid DC pulse tripping with 30/100/300 mA sensitivity complete as per specification no. SW-RCCB/RCCB

Item No.354 :- Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Item No.355 :- Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 2 core 2.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Item No.356 :- Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip)cable 1100 V, 4 core 10 sq.mm.copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no.CB-LT/CU

Item No.357 :- Supplying & erecting G.I. pipe ‘A’ class 40 mm dia. erected for enclosing XLPE armoured cable on wall/pole as per specification no. CB-CE

Item No.358 :- Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA- EP only

Item No.359 :- Supplying and erecting copper strip of high purity required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint with joints required. As per specification no. EA-EP.

Item No.360 :- Supplying and erecting 20mm dia. corrugated flexible polypropylene conduit

Item No.361 :- Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25 mm with accessories on wall/ceiling as per specification No: WG-MA/CON.

Item No.362 :- Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.363 :- Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.364 :- Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Item No.365 :- Supplying and erecting modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Item No.366 :- Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Item No.367 :- Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete

Item No.368 :- Supplying and erecting PVC Surface modular switch box with double mounting plate for 3 module duly erected.

Item No.369 :- Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 module duly erected.

Item No.370 :- Supplying and erecting 25m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete.

Item No.371 :- Supplying and installing cat-6 cable suitable for networking as per specification no. WG-COC/NC

Item No.372 :- Supplying and installing armoured single mode optical fibre cable with 6 fiber, core dia 50/125μm (OS1/OS2) 10/40 GBPS speed in provided underground HDPE pipe complete.

Item No.373 :- Supplying, fixing, and configuring 8-ports managed gigabit, Layer-2 switch, 10/100/1000 base-T, POE smart switch plus 2 SFP erected in provided rack complete.

Item No.374 :- Supplying, fixing, and configuring 24 ports, POE switch in provided rack as per specification No. WG-NWC/ENS

Item No.375 :- Supplying, installing and testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC

Item No.376 :- Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 500x600x500 mm) as per specification No. WG-NAS/RAK

Item No.377 :- Supplying and fixing 24 ports light guide unloaded interconnect unit, rack mounted type, with adapter panel for termination of optical fibre cables in provided U rack complete as per specification no. WG-NAS/ LIU

Item No.378 :- Supplying and fixing SC/LC type multimode duplex adapter to couple two connectors between OFC & Fibre switch/Fibre module as per specification no. WG-NAS/MMA

Item No.379 :- Supplying and fixing SC/SC type multimode pigtails (OM3) for LIU to terminate OFC in LIU as per specification No. WG-NAS/LIU2

Item No.380 :- Supplying and fixing 17U floor mount rack (Dimension-DxWxH – 800x600x954 mm) as per specification No. WG-NAS/RAK

Item No.381 :- Supplying, fixing and configuring 1000 BASE-T to 1000 BASE-SX (SC) single media converter for transmission distance upto 10 km with LED indication complete as per specification no. WG-NAS/SMMC

Item No.382 :- Supplying & erecting 55" professional LED display with 1920 *1080 ( Full HD) Display, suitable for 32/64 channel NVR and following features Brightness: minimum 500 Cd/m2 Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg. Response time: maximum 8 ms Inputs: HDMI, VGA, BNC,USB, Audio In, Built-in speakers maximum 10 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-MON

Item No.383 :- Supplying & erecting of High definition 4/5 Megapixel IP IR PTZ Camera with following features Image Sensor : minimum 1/2.8" Progressive Scan CMOS Video Resolution: minimum 2880 x 1620 Video Compression : H.264, H.265 or higher, at least Three individually configurable stream, Frame Rate : minimum 30 fps at all resolutions, WDR : minimum 120 dB Wide Dynamic Range, ONVIF profile conformant. Auto Tracking, Pre-set Tour Settings, Pan : 360° endless, Tilt : From -15° to 90° (auto-flip 180°), minimum Pan Speed - from 0.1°/s to 160°/s, minimum Preset Speed: 240°/s, minimum Tilt Speed - from 0.1°/s to 120°/s, minimum Preset Speed : 200°/s, Min Presets- 250, Min IR distance :150m, Lens Type : minimum 4.3 - 12.5mm Lens min 16 x digital zoom, min 30 x optical Zoom. Focus Mode : Auto/Zooming/One Push Manual, Lux sensitivity- minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White, 0.0 Lux (IR) Night Vision Distance Min IR- 150m, Power Supply : support 12/24 VDC, 24 VAC & PoE, IP67/IP66, IK10, built in micro SD/SDHC/SDXC card slot minimum 256 GB, built in microphone. minimum Input/Output : Audio in × 1, Audio Out × 1, Alarm in× 1, Alarm Out × 1. Image Settings : Rotate mode, saturation, brightness, contrast, sharpness, gain, white balance. Image Enhancements : Day/Night-Auto (ICR)/Color/Black & White, 3D Digital Noise Reduction, Automatic White Balance, Automatic Gain Control, Backlight Compensation, Highlight Compensation.

Item No.384 :- Supplying & erecting of High definition 4/5 Megapixel IP IR Bullet Camera with following features Image Sensor : minimum 1/2.8" Progressive Scan CMOS, Video Resolution : minimum 2592 x 1520 Video Compression : H.264, H.265 or higher, at least Three individually configurable stream, Frame rate : minimum 25 fps at all resolutions, WDR : minimum 120 dB Wide Dynamic Range, ONVIF profile conformant, minimum IR distance : 50m, Lens Type : 2.8/4/6 mm Lens, fixed focal, Field of View : 2.8 mm, horizontal FOV 107°, vertical FOV 57°, diagonal FOV 129° 4 mm, horizontal FOV 86°, vertical FOV 47°, diagonal FOV 102° 6 mm, horizontal FOV 55°, vertical FOV 29°, diagonal FOV 65° Lux sensitivity - minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White, 0.0 Lux (IR) Night Vision Distance minimum IR - 50m. Camera minimum Adjustment Angles - Pan : 350°, Tilt : 72°, Rotate : 350°. Power Supply : Support 12VDC & PoE, IP67, IK10 - Vandal Resistant. Built in micro SD/SDHC/SDXC card slot of minimum 128 GB, Built in microphone. minimum Input/Output - Audio in × 1, Audio Out × 1, Alarm in × 1, Alarm Out × 1. Image Settings : Rotate mode, saturation, brightness, contrast, sharpness, gain, white balance. Image Enhancements : Day/Night-Auto (ICR)/Color/Black & White, 3D Digital Noise Reduction, Automatic White Balance, Automatic Gain Control, Backlight Compensation, Highlight Compensation.

Item No.385 :- Supplying & erecting of High definition 4/5 Megapixel IP IR Dome Camera with following features Image Sensor : minimum 1/2.8" Progressive Scan CMOS, Video Resolution : minimum 2592 x 1520 Video Compression : H.264, H.265 or higher, at least Three individually configurable stream, Frame rate : minimum 25 fps at all resolutions, WDR : minimum 120 dB Wide Dynamic Range, ONVIF profile conformant, minimum IR distance : 50m, Lens Type : 2.8/4/6 mm Lens, fixed focal, Field of View : 2.8 mm, horizontal FOV 107°, vertical FOV 57°, diagonal FOV 129° 4 mm, horizontal FOV 86°, vertical FOV 47°, diagonal FOV 102° 6 mm, horizontal FOV 55°, vertical FOV 29°, diagonal FOV 65° Lux sensitivity - minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White, 0.0 Lux (IR) Night Vision Distance minimum IR - 50m. Camera minimum Adjustment Angles - Pan : 350°, Tilt : 72°, Rotate : 350°. Power Supply : Support 12VDC & PoE, IP67, IK10 - Vandal Resistant. Built in micro SD/SDHC/SDXC card slot of minimum 128 GB, Built in microphone. minimum Input/Output - Audio in × 1, Audio Out × 1, Alarm in × 1, Alarm Out × 1. Image Settings : Rotate mode, saturation, brightness, contrast, sharpness, gain, white balance. Image Enhancements : Day/Night-Auto (ICR)/Color/Black & White, 3D Digital Noise Reduction, Automatic White Balance, Automatic Gain Control, Backlight Compensation, Highlight Compensation.

Item No.386 :- Supplying, installing, testing & commissioning of 32/40 Ch Network Video Recorder (NVR), suitable connect Min. 32 IP Cameras, up to 5 Megapixel Resolution, with HDMI1/VGA1 outputs, provided Atleast one HDMI output of 4K resolution, atleast one VGA output with output up to 1920x1080, Support H.265 or higher, H.264, MJPEG, Supports Redundant Dual Power, Incoming Bandwidth 320 Mbps with minimum 8 SATA ports, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD up to 8TB, minimum 02 USB port, Alarm I/O 16/4, RJ-45 10/100/ 1000 Mbps self-adaptive Ethernet interface, support multibrand network Cameras, ONVIF conformance, Multiple network monitoring: Web viewer . support protocol TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS. RoHS, UL, CE, FCC certified. duly erected in provided U Rack with wiring connections, tagging and programming etc. complete as per specifications no. CCTV-NVR

Item No.387 :- Supplying & erecting 8 TB internal Surveillance HDD suitable for SATA Port of NVR, interface transfer rate 6 GB/S, maximum sustained transfer rate 210 MB/Sec to 213 MB/S. Drive bay supported 08+, Cameras supported up to 64, Cache (MB) 256, Load/Unload Cycle -3000000, Work Load Rating per Year 180TB, MTBF 1000000 Hrs. HTTPS. RoHS, UL, CE certified, duly erected in position in provided NVR as per specification no. CCTV-HDD

Item No.388 :- Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Item No.389 :- Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Item No.390 :- Supplying, erecting, testing and commissioning of single phase input & 1 phase output 1 kVA capacity online pure sine wave UPS, with backup time of ....... hrs. PWM & IGBT based, with 0.8 to unity output pf complete with all protections as per specification no. AP-UPS

Item No.391 :- Supplying and erecting 12 V/65Ah SMF battery with battery terminal wire, duly charged complete with 24 months warranty complete

Item No.392 :- Caution Board (6.1.16) Supplying and erecting GI sheet 1.6mm (16 SWG) caution board of size 250 x 200 mm duly painted with red oxide and enamel paint in Marathi, Hindi and English erected at position for HV/EHV (11000 Volts) installation with compliance to IS 2551-1982

Item No.393 :- Iron Work (6.1.19) Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Item No.394 :- D.T.C. meter (6.3.5) Supplying and erecting LT CT multifunction DLMS compliance energy meter of accuracy of class 0.5 , 3x240V,50 Hz with optical & RS 232 port, backlit LCD, measure & display trivector energy, load survey, TOD, tamper detection & logging, power ON /OFF events, instantaneous parameters of rating 1/5 A with display in absence of power complete with zero adjustment & test certificate from manufacturer erected on provided M.S. box and connected to CTs.

Item No.395 :- L.T. (6.5.2) Supplying and erecting LT current transformer with bar primary 50/5 to 1000/5 ratio with 15 VA burden erected in provided CRCA box duly secured with insulating materials connected to the meter with test certificates.

Item No.396 :- Un Arm. Copper cable 1x120 sq.mm (7.2.6) Supplying, erecting & terminating XLPE insulated unarmoured cable 1100 V. 1 core 120 sq. mm. copper conductor complete erected with provided lugs, laid in provided control panel /distribution boards / pipe as per specification no. CB-LT/CU

Item No.397 :- V Cross Arm (8.3.12) Supplying and erecting V cross arm with ISM channel of 75x40x6mm for 11kV HT OH line with arrangement to fix insulator at 45mm from the end & horizontal distance between insulators 1220mm bent at angle of 60 degree keeping base 305mm and the total vertical height of V cross arm as 460mm, and fixed on pole with MS clamp of 80x10 mm, nut bolts, washers complete as per specification no. OH-PL/VCA

Item No.398 :- Top Clamp (8.3.14) Supplying and erecting 75x40 x6mm with 4.4mm thick web and 7.3mm thick flange channel (top pin) with clamp of suitable length so as to maintain vertical clearance of 1065mm for 11kV, 1320mm for 22kV between insulators for erection of top pin insulators complete as per specification no. OH-PL/VCA

Item No.399 :- Guarding Bracket (8.3.15) Supplying and erecting bracket for guarding of HT OH Line, made from channel iron 1600mm in length and 75x40x6mm. erected on pole complete as per specification no. OH-PL/VCA

Item No.400 :- Single Pole cut Point (8.3.17) Supplying & erecting single pole cut point channel set of for 11kV HT OH line two channel of size 100x50x6mm 1.6m long having stud angle of size 50x50x6mm 1.5m long with necessary clamps, nut bolts etc. complete as per drawing.

Item No.401 :- ACSR Conductor (8.4.7) Supplying and erecting ACSR conductor of size 6/1-2.59 mm complete. (Weasel) (127.7 kg/km) as per specification No. OH-CON/ACSR

Item No.402 :- Disc Insulator (8.5.6) Supplying and erecting porcelain disc type insulator 45KN with necessary hardware suitable for 11kV line, complete as per specification no. OH-INS/DI (Tapping pole 3 nos ,DP structure 6 nos)

Item No.403 :- Pin Insulator (8.5.9) Supplying and erecting porcelain pin type insulator with GI pin suitable for 11kV line, complete as per specification no. OH-INS/PN ( DP structure 3 Nos)

Item No.404 :- G.I. Stay (8.6.2) Supplying and erecting G.I. stay set for poles, including loop insulators at inaccessible height with anchor plate 300x300x6 mm., straining screws, G.l. stay wire 7/8 SWG, G.l. stay rod 20mmx1.8m length and pole clamps duly erected in provided cement concrete foundation complete.

Item No.405 :- Guarding Lace (8.6.18) Supplying and erecting guarding lace for HT OH line with 8SWG G.l. wire to protect the HT OH line with binding wire of 20SWG G.l. wire for 75mm section on either side.

Item No.406 :- Galvanized Iron Earth Plate (9.1.1) Providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Item No.407 :- G.I.Strep (9.2.3) Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP.

Item No.408 :- G.I. Earth Wire (9.2.5) Supplying and erecting GI wire of high purity of required sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws complete.

Item No.409 :- C.C. Foundation (16.3.4) Making cement concrete foundation including excavation (60 x 60) cm x deep 1/6 of pole length in 1:3:6 cement concrete 20 x 25 mm stone metal, 45 cm x 45 cm x 45 cm /45 cm dia. x 45 cm. height plinth duly plastered, with necessary curing and finishing complete. (for above 9 m poles)

Item No.410 :- C.C. Foundation (16.3.6) Making cement concrete foundation including excavation (60 x 60 x 150) cm deep in 1:3:6 cement concrete, (20 to 25) mm stone metal with necessary curing and finishing complete.(for stay).

Item No.411 :- Transformer 500 KVA (10.1.9 ) Supplying, Installing, Testing & Commissioning 03 Phase, 11/0.433 KV, 50 Hz, 200 KVA, Aimeral oil immersed and naturally cooled outdoor type, alluminium wound Non-sealed transformer delta/star connected with additional neutral brought out on load side, Temperature rise should not exceed 45 C by thermometer in oil and 50 C by the resistance method in winding at full load rating, using type A winding insulation (kraft paper) with HV tapping (with off load tap changer) off load +2.5 to -5 in steps of 2.5%, having 4 number of tap positions, with losses below 780 watts at 50% load, 2300 watts at 100 load asper IS: 1180 (part 1) : 2014, with necessary premissions of Electrical inspector, as per specification no SS-TR-NSI.

Item No.412 :- AB Switch (10.6.2) Supplying and erecting 11 kV outdoor type gang operated air break, triple pole switch 400 A capacity with 3 post pin type insulator per phase, mounted in horizontal or vertical position with necessary channels on provided cross arm with adequate length of "C" class G.l. pipe for operating handle erected on extended square shaft. The operating handle provided with lock and key at suitable height from ground level with necessary clamp.

Item No.413 :- drop out fuse (10.6.5) Supplying and erecting, 11 kV outdoor type drop out fuse with insulator complete with fuse holders, fuse barrel with metal fitting, fuse element mounted on M.S. channel with working current of 15A capacity complete erected on provided cross arm.

Item No.414 :- drop out fuse (10.6.8) Supplying and erecting 11 kV fuse barrel with metal fittings complete.

Item No.415 :- (10.6.11) Supplying and erecting extra thick alkathene pipe 10 mm dia. erected to enclose bare conductor wires complete.. (use shall be restricted to H.T.)

Item No.416 :- (8.1.13 ) Supplying and erecting rolled steel joist (girder) pole 100 x 116 mm (23 kg/m) with base plate in provided foundation as per specification no. OH-PL/RSJ (DP structure =2 x 11 mtr + 2 pole x 09 mtr =40 mtr)

Item No.417 :- (8.6.16 ) Supplying and fixing MS round base plate 25cm dia and 10mm thick fixed to pole welded and fixed at position.

Item No.418 :- (8.5.15 ) Supplying and erecting distribution class, 11 kV thyrite type lightening arrester with nut bolts, on provided MS channel as per specification no. OH-INS/LA

Item No.419 :- (8.3.11 ) Supplying & erecting 100 x 50 x 6 mm with 4.7 mm thick web and 7.5 mm thick flange channel iron cross arm of suitable length for 2.4 m wide DP structure and erecting on DP with 50x6mm clamp complete as per specification no. OH-PL/BKT

Item No.420 :- (7.3.2 ) Supplying , erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) cable 11 kV(E), 3 x 95 sq. mm. aluminium conductor laid in provided trench / pipe as per specification no. CB-HT (Double run 80 mtr x 2 run =160 mtr)

Item No.421 :- (7.1.25 ) Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½core 400 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (Double run 70 mtr x 2 run =140 mtr)

Item No.422 :- (7.5.5 )Providing and erecting Heat shrinkable out door termination kit for 11 kV ( E ) XLPE HT cable 3 x up to 95 sq. mm. with necessary material as per specification No. CB-JT/HT

Item No.423 :- (16.5.9 )Supplying and erecting ISI mark GI pipe 100 mm dia. ‘B’ class at position with accessories complete. Specification no. CW-PLB/GP.(for cable inclosing on pole)

Item No.424 :- (10.6.21 )Supplying & erecting barbed wire two ply with 12 SWG ply and 12 SWG barb with a gap between two bars of 75 mm. firmly fixed on provided angle supports with necessary materials complete. (6.044 meters/kg.).

Item No.425 :- (16.3.1 ) Making transformer plinth (1.5 x 1.5 x 1.5) m in size with necessary excavation in ground with 150 mm. thick M- 10 PCC at the bottom and top and 250 mm. thick, burnt brick wall constructed at periphery and remaining hollow portion shall be filled with 40mm hard broken aggregate. External surface duly plastered by 12 mm thick including watering etc complete.

Item No.426 :- (7.6.5 ) Supplying & laying (including excavation) reinforced cement concrete pipe of IS 458:2003 NP-2 class of 150 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.(120 mtr for HT cable and 10 mtr for LT cable road crossing)

Item No.427 :- ( 16.1.4) Making trench in hard murum/Tar road having 0.9 m depth and minimum 0.3mtr width for laying provided cables of voltage range 3.3 kV to 11 kV complete as per specification No. CW-EXN-CTR

Item No.428 :- (6.1.6 ) Supplying and erecting GI sheet 1.6 mm (16 SWG) having zinc coating of 350 microns with galvanization process compliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint. ( for Distribution Box)

Item No.429 :- (5.5.5 ) Providing & erecting 4 Pole MCCB 415V, 630A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Item No.430 :- (6.2.9 ) Supplying & erecting of required size electrolyte copper flexible braided bus patti or bar in bus bar chamber/in panel or any other purpose, suitable for 500 volt with required capacity having thermal conductivity of 400W per meter with composition Pure copper 99.9% & Trillium 0.001 % & Current density 1.8 with fixing arrangement (like lug or bottle type lug) to both the end with high grade polyolefin insulation sleeve complete as per specification no. BCP-BB ( size 50x6mm flat.wt/kg=2.60 kg,total length 4 mtr x2.68=10.72=11 kg)

Item No.431 :- (5.10.28) Supplying & erecting porcelain/epoxy bus bar support complete erected in provided M.S. box for 400A

Item No.432 :- (16.2.3) Supplying and spreading stone metal 25 mm size for 100 mm depth above the ground level complete.

Item No.433 :- Cable 03 Core Flexible .25 sq.mm. (1.3.15) Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Item No.434 :- LED Street Light fitting 60 w. (2.4.5) Supplying and erecting integrated LED street light fitting 60W IP65 & IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Min. 6600 Lumens, min. efficacy of 110 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, including driver complete with 3 Years warranty as per specification No FG-ODF/FLS2.

Item No.435 :- LED Flood Light 120 Watt. (2.4.16) Supplying and erecting integrated LED flood light fitting Max. 120W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min.14500 Lumens, min. efficacy of 120 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver with U shaped bracket with 3 Years warranty as per specification No FG-ODF/FLS2.

Item No.436 :- LED Post Top (2.4.21) Supplying and erecting integrated LED Post Top 45W IP65 & IK10 class having die cast aluminium housing with UV protected polycarbonate diffuser, having system lumens output of Min.4500 Lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-240V, inbuilt surge protection of 2 kV, Life class of 30,000 Hrs. at L50B50 , including driver complete with 2 Year warranty as per specification No FG-ODF/FLS2.

Item No.437 :- Street Light Bracket (2.7.4) Supplying and erecting street light Wall bracket made from 40 mm. dia ‘ G.I. pipe 1.2 m. in total length complete as per specification no. FG-BKT/WB

Item No.439 :- SPMCB 0.5A to 5A, (5.3.1) Supplying, erecting & marking SPMCB 0.5A to 5A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

D.P. Isolator (5.3.14) Supplying, erecting and marking double pole isolator only switch version of miniature circuit breaker of 40A with required wiring connections and lugs etc. in provided distribution board.

D.P. MCB (5.4.13) Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Item No.440 :- CRCA Sheet (6.1.1) Supplying and erecting metal work in CRCA sheet including Iron work for supports with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete.

Item No.441 :- Iron Work (6.1.19) Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Item No.442 :- FR XLPE 4x6 sq.mm. (7.1.27) Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.443 :- D.W.C. Pipe 50 mm (7.6.9) Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Item No.444 :- FRP Box (7.8.8) Supplying & erecting FRP box of size 150mm x 125mm x 100 mm, 2.7 mm thick complete on pole/wall as per specification No. CB-SB

Item No.445 :- Octagonal Pole 6 mtr. (8.2.12) Providing & erecting 6 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Item No.446 :- Sword Type Bracket (8.2.21) Providing and erecting galvanised 1000mm single arm sword type bracket with FRP dome and ball as per specification no. OH-PL/PBKT

Item No.447 :- Sword Type Double Bracket (8.2.22) Providing and erecting galvanised 1000mm double arm sword type bracket with FRP dome and ball as per specification no. OH-PL/PBKT

Item No.448 :- Plate Earthing (9.1.1) Providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Item No.449 :- Pipe Type Earthing (9.1.4) Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP

Item No.450 :- C.C. Foundation for Pole (16.3.9) Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole).

Item No.451 :- G.I. Pipe 40 mm (16.5.5) Supplying and erecting ISI mark GI pipe 40 mm. dia. ‘B’ class at position with accessories complete as per specification no. CW-PLB/GP.

Item No.452 :- Flexible Conduit 25 mm (1.2.2) Supplying and erecting 25 mm dia. corrugated flexible polypropylene conduit

Item No.453 :- Mains 2x6 sq.mm (1.3.4) Supplying and erecting mains with 2x6 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.454 :- TPMCB 6 A to 32 A (5.3.10) Supplying, erecting & marking TPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Item No.455 :- FPMCB 40 A to 63 A (5.3.13) Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Item No.456 :-Change Over Switch (5.3.26) Supplying, fixing and commissioning MCB type change over switch 4 pole, 63A with 3 positions (I-O-II) with centre off position as per specification no. SW-SWR / MCBCOS

Item No.457 :- TPNDB (5.4.4) Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 4 ways /12 Poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Item No.458 :- MCB Enclosures (5.4.13) Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Item No.459 :- MCCB 03 Pole (5.5.1) Providing & erecting 3 Pole MCCB, 415 V, 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Item No.460 :- CRCA Sheet (6.1.1) Supplying and erecting metal work in CRCA sheet including Iron work for supports with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete.

Item No.461 :- Iron Work (6.1.19) Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Item No.462 :- FRXLPE 4x16 Cable (7.1.29) Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.463 :- FR XLPE Cable (7.2.32) Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Item No.464 :- G.I. Pipe 40 mm (7.6.2) Supplying & erecting G.I. pipe ‘A’ class 40 mm dia. erected for enclosing XLPE armoured cable on wall/pole as per specification no. CB-CE

Item No.465 :- D.W.C. Pipe 50 mm (7.6.9) Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Item No.466 :- Pipe Type Earthing (9.1.4) Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP

Item No.467 :- Submersible Pump Set (12.2.10) Supplying and erecting minimum Three & above star rated submersible pump set of 5.625 KW/7.5 HP with 415 V, 50 c/s AC supply suitable for 150 mm dia. borewell suitable for 110 to 510 LPM discharge at 107 to 30 m head & discharge & delivery pipe of Size-50 mm diameter with a necessary H type clamps as per specification No. WP-SMP

Item No.468 :- Open Well Submersible Pump Set (12.3.2) Supplying and erecting minimum Three & above star rated submersible pump set suitable for erection on open well of 3.75 KW/5 HP with 415 V 50 c/s. A.C. supply, having delivery head from 43 to 11m and discharge from 120 to 840 litres. per minute & pipe of Suction 65mm / Delivery 50 mm diameter erected with necessary H type clamps as per specification No. WP-OSP

Item No.469 :- Flat Flexible 3x4 sq.mm. Cable (12.4.9) Supplying & erecting flat flexible 3 core 4 sq.mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

Item No.470 :- Automatic Control Panel (12.4.17) Supplying & erecting automatic control panel for 3 Phase , 415 volt, A.C, Submersible/centrifugal pump set up to 7.5 HP consisting of DOL starter having relay range 9-14 AMP,S.P.P., Combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc .

Item No.471 :- C.C. Foundation (16.3.7) Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) mm. stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose).

Item No.472 :- G.I. Pipe 50 mm (16.5.6) Supplying and erecting ISI mark GI pipe 50 mm dia.‘B’ class at position with accessories complete as per specification no. CW-PLB/GP.

Item No.473 :- Non Return Valve 50 mm Dia (16.6.21) Supplying and erecting non return valve 50 mm dia in position made of gun metal complete.

Item No.474 :- Split Type A.C. (3.2.11) Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor. room air conditioning unit 1.7TR to 2.0TR capacity having ISEER minimum 5.0 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position in provided recess with wooden frame complete specification no. AP-AC/WAC

Item No.475 :- Copper Pipe (3.2.26) Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 12mm complete.

Item No.476 :- Copper Pipe (3.2.27) Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 16mm complete.

Item No.477 :- Elastomeric (4.2.9) Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 12 mm for solar water heater/AC system.

Item No.478 :- Elastomeric (4.2.10) Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 16 mm for solar water heater/AC system

Item No.479 :- Iron Work (6.1.19) Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Item No.480 :- MCCB 04 Pole (5.5.2) Providing & erecting 4 Pole MCCB, 415V, 200A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Item No.481 :- S.S. Enclosure (5.11.18) Supplying and erecting SS enclosure for MCCB suitable for 125A to 200A MCCB.

Item No.482 :- Arm. cable 3½ core 95 sq. mm. (7.1.19) Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.483 :- Copper earth Plate (9.1.2) Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Item No.484 :- Copper Strip (9.2.2) Supplying and erecting copper strip of high purity required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint with joints required. As per specification no. EA-EP.

Item No.485 :- 82.5 KVA D.G. Set (11.1.11) Supplying, erecting, testing and commissioning of diesel generating set with alternator of 82.5 kVA output continuous rating, 3 Phase, 415 V, 50c/s 0.8 p. f. A.C supply, a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %, with performance class G2 and maximum fuel consumption 14.0 Ltr/hr @75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite Acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level up to 75 dB at 1.0 m, provided with first filling of oil, diesel not less than 145 Ltr etc. on provided M20 Grade CC Foundation as per specification no. GEN-DG

Item No.486 :- AMF Panel (11.2.9) Supplying, erecting, testing and commissioning of microprocessor based AMF panel suitable for diesel generating set of above 62.5 kVA up to 82.5 kVA capacity Three phase, 415 Volts, 50Hz A.C. with all standard features, safeties etc as per specification no. GEN-AMF.

Item No.487 :- Excavation (16.1.7) Excavating soft murum / soft soil road by chiselling for preparing pit for poles stay or earth plates or for laying cables, pipes & clearing the site by removing debris & making the site good complete.

Item No.488 :- C.C. Foundation (16.3.7) Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) mm. stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose).

S.S.Civil Projects Private Limited