REPAIR TO JOINERY SHEET, FLOORING, PLUMBING IN POWER HOUSE/PUMP HOUSE BLDGS AND INSTALLATION AREA UNDER AGE B/R-II UNDER GE PANAGARH

Amount

Taking down cement plaster of any description on concrete surfaces such as soffit of RCC slab, chajjas and brick walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar (1:6),complete all as specified and directed.

M&L for preparation of new plastered or un -plastered from walls, and applying two coats of oil bound distemper on walls, over and including a coat of white wall care putty complete all as specified and as directed.

M&L for preparation of new plaster surface & apply two coats of cement based paint over a coat alkali primer resistance complete all as specified and directed.

Taking down wooden shutter not exc 1.00 each and removing to store complete all as specified and directed.

Taking down wooden shutter exc 1.00 Sqm but not exc 2.00 each and removing to store complete all as specified and directed.

Taking down chowkats or frames with shutter w/o taking off shutter from the frame n exc 1.5 sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) complete all as specified and directed.

Taking down chowkats or frames with shutter w/o taking off shutter from the frame exc 1.5 sqm & n. exe 4 sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) complete all as specified and directed.

S&F 2nd class hard wood plain solid straight chowkhat and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joint complete all as specified and directed.

S & F glazed and gauged Skelton shutter (Factory made) 30mm thick of second class hard wood open rebated & prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut & mitred beads for securing glass etc including priming coat. Size of members of shutters as specified in SSR Part -I Section 8, clause 8.20 ,and shop coat of pink primer complete all as specified and directed.

S&F35 mm thick 2nd class hard wood pannel framed shutter of (any number of panels) with panels of timber flat on both sides (feather edged ) or of veneered particale board medium density, wood particale board with commercial face veneers complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads. complete all as specified and directed.

Supply and fix 4mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty (or beading ) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

S & F solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC foam sheet meter cut to two corner and jointed with 2 nos of 1500mm long bracket of 15x15 squre tube .the two vertical door profile are to be reinforced with 19x19mm squre tube of 19 gauge EPDM rubber gascut weather seal to be provided through out the frame frame shall be fixed to wall using 65x100mm long ms screw through the frame by using PVC fasterner (inc hold fast)and minium of 4 nos of screw to be provided for each vertical member & 2 nos for horzintal complete all as specified and directed

Supply and Fix, factory made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.

S & F in repair Galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F aluminium, anodized barrel tower bolts of extruded section and fixed, 100 mm long, dia of bolt not less than 10 mm, ISI marked, complete all as specified.

S&F aluminium, anodized barrel tower bolts of extruded section and fixed, 150 mm long, dia of bolt not less than 10 mm, ISI marked, complete all as specified.

S&F aluminium handles, cast type anodized of size 100 mm, ISI marked complete all as specified and directed.

S&F stainless steel butt hinges, medium weight, and fixed with screws or with welding to existing MS frames, 100 mm size, ISI marked, complete all as specified and directed.

S&F stainless steel butt hinges, medium weight, and fixed with screws or with welding to existing MS frames, 75 mm size, ISI marked, complete all as specified.

Supply and fix in repair aluminium (extruded section body) door closer hydraulically regulated designation No-3 universal type, suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

Supply and Fix, in repair aluminium Alloy, anodised, sliding door bolt, length of bolt 300 mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

M&L as in repair 150mm length of Double leg aluminium anodised door stopper with rubber foot, ISI marked and fixed with standard aluminium screws complete all as specified and directed.

Cutting holes in brick walls built in cement mortar or cement lime or inserting hold fast and making good dismantled portion in cm 1:3 or cement concrete 1:2:4 type B1 as required exc half brick but n.exc one brick complete all as specified and directed.

Supply and fixing mild steel flat iron of size 30 X 5 mm work as in hold fast and similar small articles including required cutting , bending and fixing complete, mild steel conforming (Fe-410-0 or Fe-310-0) complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm girth or width and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface not exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

M&L for preparation of old painted wooden surfaces over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old surface of steel surface scraping/rubbing and applying two coat of synthtic enamal paint of any description over 10cm in width or grith, over one coat of red oxide, complete all as specified and directed.

M&L for coloured non skid ceramic tiles 7 to 8 mm thick (Square/Rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry over 15 mm thick screed bed or bedding layer in cement mortar (1:6) and dismantilling of floor tiles including cement mortor beding complete all all as specified. Note: Design, shade and pattern of fixing of tiles shall be as directed and approved by GE

M&L for glazed cermic tiles 300x200x6 to 7 mm thick in vertical surfaces such as skirting and dados, set and jointed in neat cement slurry and pointed in coloured cement to match and including 10 mm thick rendering in cement mortar (1:4) incl dismantilling of floor tiles including cement mortor beding complete all as specified and directed.Note: Design, shade and pattern of fixing of tiles shall be as directed and approved by GE

S&F in repairs 15 mm bib tap, cast copper alloy fancy type short body chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair 10 litre capacity PVC valveless, syphonic action type low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe and brackets complete all as specified and directed

S&F in repair Pillar taps, cast copper alloy, with capstan heads,chromium plated,screwed down highpressure, with or without lettered 'Hot' or 'Cold' withlong screwed shanks and fly-nuts,screwed for iron pipe and fixed,fancy type suitable for 15 mm bore pipe, complete all as specified and as directed.

S&F in repair PVC connection 15mm size PTMT nuts of length 450mm.complete all as specified and directed.

S&F in repair Stainless steel Soap dish fancy type complete all as specified and directed.

S&F in repair Stainless steel towel rail 20mm dia D type solid 60cm long between flanges of approved make and pattern, fixed to walls with screws complete all as specified and directed

S & F in repairs wash basins, vitreous china, white, flat back, size 550 mm X 400 mm with and including cast iron brackets (embedded in wall upto 110 mm depth with and including cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate or fixing on wall with and including rawl plug and screws), 32 mm nominal size, copper alloy, nickel chromium plated finish waste fittings, including painting of fittings and brackets, sealing gap between wall and basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste pipes, waste fittings etc. with silicone sealant complete all as specified and as directed.

S & F in repair vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440mm, white, with integral foot rests and with ‘P’ or ‘S” trap, (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including provision of lime concrete bedding,including making good to existing (floor / Tiles). complete all as specified and directed.

Supply and Fix in repair stop valves, cast copper alloy , fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle,long shank and cup (concealed type), screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.

Material and labour for 15mm dia GI tubing medium grade with all fittings to walls, ceiling or laid under floors including taking up or down steel tubing and connections 15 mm bore complete all as specified and directed.

Dismantling of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed.

M&L for fly ash brick straight or curved on plan exc 6 mtr mean redious built in cement mortar (1:4) etc complete all as specified and directed.

M&L for brick work using old size bricks (EXCEPT BRICKS) straight or curved on plan exceeding 6.00 metre mean radius, built in cement mortar (1:4 ) etc all complete all as specified and directed.

M&L for 15mm thick plaster in brick work in cement & sand mortar 1:4 in fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) complete all as specified and directed.

M & L for preparation of new plastered surface of wall and applying three coats of white wash complete all as specified and directed.

M&L preparation of old decorated surfaces of walls including brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss and efflorescent salts and trading oil, greasy spots and apply one coat of white wash on walls complete all as specified and directed.

M & L for preperation of old plastered surfaces of wall and applying one coat of cement based paint including filling of small holes on decoarated wall surfaces etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving n. exc 15 cm thickness below or above GL complete all as specified and directed.

Materials and Labour for 100 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded aggregate as in sub base in floor/paving/hardstanding ,complete all as specified and directed.

Materials and Labour for pcc 25mm thick type B-I 1:24 ,(20mm graded stone aggregate) as in floor finish complete all as specified and as directed

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded aggregates as in plinth protection/floor including finishing surface even and smooth without using extra cement complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 20-25 mm thick, laid over & including 20 mm thick (average thickness) cement mortar (1:6) screed and jointed with grey cement slurry mixed with matching shade pigment including rubbing and polishing (Granite finish) complete all as specified and directed.

M & L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L for hardcore broken stone of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Material and labour for 20cm x 20cm x25mm thick chequered cement concrete tiles of approved size, set, jointed and pointed using with grey cement and pigment in floors, paving etc. including the setting and jointing in neat cement paste or slurry 0.3kg/Sqm over 15 mm thick screed bed or bedding layer in cement mortar (1:6) complete as per manufacturer instructions and direction.

M & L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thick M-35 grade with grey cement and pigment complete all as specified and directed.Note: Design, shade and pattern of fixing of paver block shall be as directed and approved by GE

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws including dismantling of plain or corrugated steel sheeting, any gauge, thickness, flat or curved incl ridges hips valleys as in roof coverings, complete all as specified and directed.

M&L for 6 mm thick asbestos cement corrugated or semi-corrugated sheets in roofs, walls, etc fixed with L-type or J-type or cranked hook bolts, including dismantling of asbestos cement (corrugated, semi corrugated etc) of any thickness, including ridges, hips, valleys as in roof coverings complete all as specified and directed.

S&F galvanized corrugated mild steel sheeting 0.63 mm thick with two corrugation side lap fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 fixed with L-type or J-type or cranked hook bolts in roofs including dismantling of plain or corugated steel sheet.complete all as specified and directed.

Removal of complete existing treatment of any description on roof surfaces of any description and roughening surfaces of old concrete floor by picking sweeeping clean and washing down with water to remove dust, forign items complete all as specified and directed.

M&L for cement concrete type B0 1:2:4 (12.5mm graded stone aggregate) in padding for levelling course of roof, rounded or chamfer edge sloping, the roof slab etc concrete mixed with water proofing compound complete all as specified and directed. Note:-WPC measured and paid separately

Material and Labour for rendering 10mm thick on fair faces on roof surfaces of concrete surfaces in cement mortar (1:4) mixed with water proofing compound complete all as specified and directed. Note:-WPC measured and paid separately complete all as specified and directed.

Material & Labour for preparation ne surfaces of roof and applying two cpats of Ployurethene (PU) acrylic based water proofing liquid compound over & including one coat of self priming primer @ one litre per ten sqm with reinforcing fabric sheet as per manufactures instruction to stop leakage/seepage from roof/wall complete all as specified and directed by the Engineer-in-Charge. Notes:- (i) As per description of theis item minimum two coats of Ployurethene (PU) acrylic based water proofing liquid compound over one coat of primer shall be carried out by as per manufacturer instruction. Please note no price adjustment shall be made, if as per manufacturer instructions more coats of Polyurethene(PU) acrylic based water proofing liquid compound & primer are required for roof treatment. (ii) Quoted rate shall be deemed to be included for work in building/Structure of any height.

Supply only integral water proofing compound, complete all as specified.

Dismantling structural steel work or & including door, gates any description complete all as specified and directed.

S&F rolled mild steel angle iorn or tee section Fe 410W (grade250) framed work as in roof covering ,trusses ,purlin ,rails and fasterning and heave bracket frame in (beam,tee,angle, channel of flat section including distence pieces, cleats etc incl cutting to dead length where reqired ,notching, drilling, fitting,riviting and or wellding or connecting with bolts and nuts (including rivits or bolts and nuts)and fixing complete all as specified and directed.

UNIQUE ENTERPRISE

S. D. Construction Co.