For fixing of rate contract for repairs to different types of damaged pumps and motors installed at various WSSs of District Ganderbal, Budgam and Srinagar

Amount

Repairs to 7.5HP Oil-Type open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop in a private load carrier arranged by the firm, repairing, shifting back to site, re-fitting and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop.The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Mechanical seal complete assembly.

Fresh Oil as per standard.

Providing and fitting of new bearings suitable for above rated motor

Repairs to 10HP Oil-Type open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop in a private load carrier arranged by the firm, repairing, shifting back to site, re-fitting and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop.The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Mechanical seal complete assembly.

Fresh Oil as per standard.

Providing and fitting of new bearings suitable for above rated motor

Repairs to 12.5HP Oil-Type open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop in a private load carrier arranged by the firm, repairing, shifting back to site, re-fitting and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop.The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Mechanical seal complete assembly.

Fresh Oil as per standard.

Providing and fitting of new bearings suitable for above rated motor

Repairs to 15HP Oil-Type open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop in a private load carrier arranged by the firm, repairing, shifting back to site, re-fitting and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop.The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Mechanical seal complete assembly.

Fresh Oil as per standard.

Providing and fitting of new bearings suitable for above rated motor

Repairs to 17.5HP Oil-Type open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop in a private load carrier arranged by the firm, repairing, shifting back to site, re-fitting and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop.The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Mechanical seal complete assembly.

Fresh Oil as per standard.

Providing and fitting of new bearings suitable for above rated motor

Repairs to 20HP Oil-Type open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop in a private load carrier arranged by the firm, repairing, shifting back to site, re-fitting and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop.The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Mechanical seal complete assembly.

Fresh Oil as per standard.

Providing and fitting of new bearings suitable for above rated motor

Repairs to 25HP Oil-Type open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop in a private load carrier arranged by the firm, repairing, shifting back to site, re-fitting and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop.The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Mechanical seal complete assembly.

Fresh Oil as per standard.

Providing and fitting of new bearings suitable for above rated motor

Repairs to 30HP Oil-Type open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop in a private load carrier arranged by the firm, repairing, shifting back to site, re-fitting and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop.The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Mechanical seal complete assembly.

Fresh Oil as per standard.

Providing and fitting of new bearings suitable for above rated motor

Repairs to 35HP Oil-Type open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop in a private load carrier arranged by the firm, repairing, shifting back to site, re-fitting and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop.The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Mechanical seal complete assembly.

Fresh Oil as per standard.

Providing and fitting of new bearings suitable for above rated motor

Repairs to 40HP Oil-Type open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop in a private load carrier arranged by the firm, repairing, shifting back to site, re-fitting and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop.The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Mechanical seal complete assembly.

Fresh Oil as per standard.

Providing and fitting of new bearings suitable for above rated motor

Repairs to 45HP Oil-Type open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop in a private load carrier arranged by the firm, repairing, shifting back to site, re-fitting and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop.The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Mechanical seal complete assembly.

Fresh Oil as per standard.

Providing and fitting of new bearings suitable for above rated motor

Repairs to 50HP Oil-Type open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop in a private load carrier arranged by the firm, repairing, shifting back to site, re-fitting and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop.The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Mechanical seal complete assembly.

Fresh Oil as per standard.

Providing and fitting of new bearings suitable for above rated motor

Repairs to 7.5HP water Cooled open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site, re-fitting, lowering of pumping unit in the well/sump and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap@ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per pumping unit after extracting the old damaged ones by suitable tools and tackles, skilled technical manpower etc. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, skilled technical manpower, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap.

Repairs to 10HP water Cooled open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site, re-fitting, lowering of pumping unit in the well/sump and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap@ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per pumping unit after extracting the old damaged ones by suitable tools and tackles, skilled technical manpower etc. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, skilled technical manpower, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap.

Repairs to 12.5HP water Cooled open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site, re-fitting, lowering of pumping unit in the well/sump and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap@ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per pumping unit after extracting the old damaged ones by suitable tools and tackles, skilled technical manpower etc. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, skilled technical manpower, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap.

Repairs to 15HP water Cooled open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site, re-fitting, lowering of pumping unit in the well/sump and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap@ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per pumping unit after extracting the old damaged ones by suitable tools and tackles, skilled technical manpower etc. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, skilled technical manpower, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap.

Repairs to 17.5HP water Cooled open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site, re-fitting, lowering of pumping unit in the well/sump and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap@ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per pumping unit after extracting the old damaged ones by suitable tools and tackles, skilled technical manpower etc. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, skilled technical manpower, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap.

Repairs to 20HP water Cooled open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site, re-fitting, lowering of pumping unit in the well/sump and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap@ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per pumping unit after extracting the old damaged ones by suitable tools and tackles, skilled technical manpower etc. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, skilled technical manpower, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap.

Repairs to 25HP water Cooled open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site, re-fitting, lowering of pumping unit in the well/sump and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap@ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per pumping unit after extracting the old damaged ones by suitable tools and tackles, skilled technical manpower etc. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, skilled technical manpower, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap.

Repairs to 30HP water Cooled open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site, re-fitting, lowering of pumping unit in the well/sump and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap@ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per pumping unit after extracting the old damaged ones by suitable tools and tackles, skilled technical manpower etc. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, skilled technical manpower, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap.

Repairs to 40HP water Cooled open well submersible Motor Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site, re-fitting, lowering of pumping unit in the well/sump and successful testing on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap@ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per pumping unit after extracting the old damaged ones by suitable tools and tackles, skilled technical manpower etc. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, skilled technical manpower, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scraps shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap.

Repairs to 3-Phase 5HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 7.5HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 10HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 12.5HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 15HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 17.5HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 20HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 25HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 30HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 35HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 40HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 45HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 50HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 60HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 75HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 85HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3-Phase 100HP Submersible Motor. Dismantling of the submersible motor at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the material from site to workshop and back after repairs. At site the motor shall be recoupled with the pump all power connections shall be reconnected with the motor and pump motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new Rubber Washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Rewinding by using PVC Insulated Cu-wire (Reputed make) of proper gauge and specification in the stator slots of the motor as per actual pitch and turns after extraction /removal of the damaged/burnt out windings from all stator slots by special tools & tackles, skilled manpower and cleaning of slots thereof. The job includes insulation of the windings by proper insulating material, tape, Skilled labour, sleeves, insulated PVC paper, crimpled paper, bamboo sticks, thread etc. Then assembling back of rotor, stator, cover plates, all nuts and bolts of the motor and testing on no load at the workshop. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap @ 80% of total weight.

Replacement of motor shaft (Machined/Finished) which includes rebate on account of damaged shaft.

Repairs to damaged or broken Rotor shaft by way tapping/internal threading, welding/remetalling, Stud bolts, machining etc.

Providing and fitting of new Ratchet racer assembly complete of standard/reputed make as per requirement of pumping unit after extracting the old damaged one by suitable tools and tackles. The job shall include rebate on account of old damaged item.

Fabrication, providing, inserting & fitting of new bronze/gun metal bushes and rubber bushes (02 No’s each) in the lower and upper manifolds of the Submersible motor in place of damaged bushes by way of first extracting the old damaged bushes from the manifolds by means of tools and tackles, making the inner surfaces of the manifolds good by machining on lathe. The job shall include casting, fabrication, machining & finishing of the new bushes, before being fixed into the manifolds. The Old scrap shall be retained by the firm. The rates quoted should be after the deduction of cost of old scrap

Replacement of Water seal as per requirement.

Replacement of Sand guard as per requirement.

Repairs to 3'' Submersible Pump Dismantling of the submersible pump at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the pump from site to workshop and back after repairs. At site the pump shall be recoupled with the motor all power connections shall be reconnected with the pump and motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new rubber washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Replacement of impeller

Bronze

Cast Steel / Stainless Steel.

Noryl

Replacement of Diffuser

Bronze

Cast Steel / Stainless Steel.

Noryl

Replacement of Pump Bowl

Fabrication, providing and fitting of Pump Shaft

Replacement of cast iron non return valve

Replacement of Stainless-steel strainers

Replacement of cast iron threaded discharge outlet

Replacement of bowl stage bushes for fitment of impellers

GM/Bronze

Cast Steel / Stainless Steel.

Nitryl rubber

Fabrication, providing, fitting of MS nipples threaded on one side and flanged on other side with length 600mm as per site requirement (with thickness of pipe and flange as per sample

50 mm Dia

65 mm Dia

80 mm Dia

100 mm Dia

Fabrication, providing and fitting of locking arrangement

Replacement of GM Wear ring (Machined/Finished) as per sample

Replacement of GM Neck ring (Machined/Finished) as per sample

Muff coupling (Machined/finished) out of SS-400 material as per sample

Fabrication and fitting of Coupling key/Cotter (Machined/Finished) as per sample

Repairs to 4'' Submersible Pump Dismantling of the submersible pump at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the pump from site to workshop and back after repairs. At site the pump shall be recoupled with the motor all power connections shall be reconnected with the pump and motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new rubber washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Replacement of impeller

Bronze

Cast Steel / Stainless Steel.

Noryl

Replacement of Diffuser

Bronze

Cast Steel / Stainless Steel.

Noryl

Replacement of Pump Bowl

Fabrication, providing and fitting of Pump Shaft

Replacement of cast iron non return valve

Replacement of Stainless-steel strainers

Replacement of cast iron threaded discharge outlet

Replacement of bowl stage bushes for fitment of impellers

GM/Bronze

Cast Steel / Stainless Steel.

Nitryl rubber

Fabrication, providing, fitting of MS nipples threaded on one side and flanged on other side with length 600mm as per site requirement (with thickness of pipe and flange as per sample

50 mm Dia

65 mm Dia

80 mm Dia

100 mm Dia

Fabrication, providing and fitting of locking arrangement

Replacement of GM Wear ring (Machined/Finished) as per sample

Replacement of GM Neck ring (Machined/Finished) as per sample

Muff coupling (Machined/finished) out of SS-400 material as per sample

Fabrication and fitting of Coupling key/Cotter (Machined/Finished) as per sample

Repairs to 5'' Submersible Pump Dismantling of the submersible pump at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the pump from site to workshop and back after repairs. At site the pump shall be recoupled with the motor all power connections shall be reconnected with the pump and motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new rubber washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Replacement of impeller

Bronze

Cast Steel / Stainless Steel.

Noryl

Replacement of Diffuser

Bronze

Cast Steel / Stainless Steel.

Noryl

Replacement of Pump Bowl

Fabrication, providing and fitting of Pump Shaft

Replacement of cast iron non return valve

Replacement of Stainless-steel strainers

Replacement of cast iron threaded discharge outlet

Replacement of bowl stage bushes for fitment of impellers

GM/Bronze

Cast Steel / Stainless Steel.

Nitryl rubber

Fabrication, providing, fitting of MS nipples threaded on one side and flanged on other side with length 600mm as per site requirement (with thickness of pipe and flange as per sample

50 mm Dia

65 mm Dia

80 mm Dia

100 mm Dia

Fabrication, providing and fitting of locking arrangement

Replacement of GM Wear ring (Machined/Finished) as per sample

Replacement of GM Neck ring (Machined/Finished) as per sample

Muff coupling (Machined/finished) out of SS-400 material as per sample

Fabrication and fitting of Coupling key/Cotter (Machined/Finished) as per sample

Repairs to 6'' Submersible Pump Dismantling of the submersible pump at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the pump from site to workshop and back after repairs. At site the pump shall be recoupled with the motor all power connections shall be reconnected with the pump and motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new rubber washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Replacement of impeller

Bronze

Cast Steel / Stainless Steel.

Noryl

Replacement of Diffuser

Bronze

Cast Steel / Stainless Steel.

Noryl

Replacement of Pump Bowl

Fabrication, providing and fitting of Pump Shaft

Replacement of cast iron non return valve

Replacement of Stainless-steel strainers

Replacement of cast iron threaded discharge outlet

Replacement of bowl stage bushes for fitment of impellers

GM/Bronze

Cast Steel / Stainless Steel.

Nitryl rubber

Fabrication, providing, fitting of MS nipples threaded on one side and flanged on other side with length 600mm as per site requirement (with thickness of pipe and flange as per sample

50 mm Dia

65 mm Dia

80 mm Dia

100 mm Dia

Fabrication, providing and fitting of locking arrangement

Replacement of GM Wear ring (Machined/Finished) as per sample

Replacement of GM Neck ring (Machined/Finished) as per sample

Muff coupling (Machined/finished) out of SS-400 material as per sample

Fabrication and fitting of Coupling key/Cotter (Machined/Finished) as per sample

Muff coupling (Machined/finished) out of SS-400 material as per sample

Fabrication and fitting of Coupling key/Cotter (Machined/Finished) as per sample

Repairs to 7'' Submersible Pump Dismantling of the submersible pump at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the pump from site to workshop and back after repairs. At site the pump shall be recoupled with the motor all power connections shall be reconnected with the pump and motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new rubber washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Replacement of impeller

Bronze

Cast Steel / Stainless Steel.

Noryl

Replacement of Diffuser

Bronze

Cast Steel / Stainless Steel.

Noryl

Replacement of Pump Bowl

Fabrication, providing and fitting of Pump Shaft

Replacement of cast iron non return valve

Replacement of Stainless-steel strainers

Replacement of cast iron threaded discharge outlet

Replacement of bowl stage bushes for fitment of impellers

GM/Bronze

Cast Steel / Stainless Steel.

Nitryl rubber

Fabrication, providing, fitting of MS nipples threaded on one side and flanged on other side with length 600mm as per site requirement (with thickness of pipe and flange as per sample

50 mm Dia

65 mm Dia

80 mm Dia

100 mm Dia

Fabrication, providing and fitting of locking arrangement

Replacement of GM Wear ring (Machined/Finished) as per sample

Replacement of GM Neck ring (Machined/Finished) as per sample

Muff coupling (Machined/finished) out of SS-400 material as per sample

Fabrication and fitting of Coupling key/Cotter (Machined/Finished) as per sample

Muff coupling (Machined/finished) out of SS-400 material as per sample

Fabrication and fitting of Coupling key/Cotter (Machined/Finished) as per sample

Repairs to 8'' Submersible Pump Dismantling of the submersible pump at site, shifting to the workshop, repairing, shifting back to site. All the technical manpower, tools and tackles involved in the execution of the job for disassembling and assembling after repairs shall be arranged by the firm. The job is inclusive of transportation charges for shifting the pump from site to workshop and back after repairs. At site the pump shall be recoupled with the motor all power connections shall be reconnected with the pump and motor assembly shall be lowered back into the sump/Well by refitting each of the column pipes one by one, tightening all the nuts and bolts & inserting the new rubber washers/RI cloth in between the flanges where ever required. After complete lowering of the unit by the firm, the unit shall be tested on full load. Job includes repairing / fabrication and providing / replacement of following items.

Replacement of impeller

Bronze

Cast Steel / Stainless Steel.

Noryl

Replacement of Diffuser

Bronze

Cast Steel / Stainless Steel.

Noryl

Replacement of Pump Bowl

Fabrication, providing and fitting of Pump Shaft

Replacement of cast iron non return valve

Replacement of Stainless-steel strainers

Replacement of cast iron threaded discharge outlet

Replacement of bowl stage bushes for fitment of impellers

GM/Bronze

Cast Steel / Stainless Steel.

Nitryl rubber

Fabrication, providing, fitting of MS nipples threaded on one side and flanged on other side with length 600mm as per site requirement (with thickness of pipe and flange as per sample

50 mm Dia

65 mm Dia

80 mm Dia

100 mm Dia

Fabrication, providing and fitting of locking arrangement

Replacement of GM Wear ring (Machined/Finished) as per sample

Replacement of GM Neck ring (Machined/Finished) as per sample

Muff coupling (Machined/finished) out of SS-400 material as per sample

Fabrication and fitting of Coupling key/Cotter (Machined/Finished) as per sample

Muff coupling (Machined/finished) out of SS-400 material as per sample

Fabrication and fitting of Coupling key/Cotter (Machined/Finished) as per sample

M/S ADIL ENGINEERING WORKS

SHAWL ENGINEERING WORKS

M/S NEW BUHROO ELECTRICAL AND MECH ENGG WORKS

M/s SAJID ENGINEERING WORKS

M/S NAASIR ENGINEERING WORKS