REPAIR OF PLUMBING, SANITARY, JOINERY, EXTERNAL PLASTERING, CHAJJA, PARAPET WALL, RWP, ROOF TREATMENT AND MISC REPAIRS AT DHAR ROAD UNDER GE (ARMY) DHAR ROAD

Amount

Demolition of cement concrete (un-reinforced) in ground floor and in paving not exceeding 15 cm thickness ( below or above ground level) complete

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (Reinforcement cut as required to facilitate demolition)

M&L for 50 mm thick in Plain cement concrete type C1 ( 1:3:6)( using 20 mm graded aggregate ) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each) finished even and smooth at top without using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight all as directed at site.

M&L 40mm thick PCC (1:2:4) type B1 using 20mm graded aggregate as in floor finished even and smooth using extra cement complete all as specified as directed.

M&L for providing cement concrete Type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) as nominal mix in lintels upto 1.5m clear span, cills, steps, parapets, copings, bed plates, and the like including weathering, slightly rounded or chamfered angles and throating, as directed including use of form work etc

Description all as per serial item No 06 above but chajjas/beems complete all as specified and as directed.

Formwork to flat soffits of suspended slabs such as roof slabs, floors slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surfaces complete all as specified and directed .

Formwork to flat chullah hoods, chajjas, beams, troughs and similar item incl edges etc

Dimolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified.

M&L for Brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM(1:4)

M&L for Brickwork with subclass `B' bricks, straight or curved on plan to any radius in half thick brick built in CM(1:4)

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 sqm each complete all as specified

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each complete.

Taking down shutters of any description not exceeding 1.5 Square metre each complete.

Taking down shutters of any description exceeding 1 Square metre and not exceeding 2 Square metre each complete.

Taking down shutters of any description n exc 1 Sqm each and re fixing in same opening

Taking down shutters of any description exc 1 Sqm but n exc 2 Sqm each and re fixing in same opening

Factory made, 2nd class hard wood,35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass / gauge etc. (without sash bars) edges or framing plain, chamfered or rounded fitted with cut or mitered beads and with mullinas for securing glass etc. size of members of shutters as specified in SSR Part - I section 8.20 (a), all as specified and directed by Engr-in-Charge.

Factory made, 35 mm thick 2nd class hard wood, Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side sflush shutters 35 mm thick complete, all as specified and directed by Engr-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick ( style ) consisting of frame made out of mild steel tubes for top and bottom rails . Mild steel frame shall be covered with heat moulded plain cover PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail and bottom rail on either side and gap insert for top rail and bottom rail ; Paneling of plain colour PVC sheet to be fitted in the mild steel frame welded /sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement supplying and fixing in the frame at site as per specification clause No 8B.1 to 8B.10 and drawing on page No 146 of MES SSR-2010 Part-II.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification and drawing on and as directed by the Engr- in-Charge.

S&F Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate incl filling hollow of frame with plain cement concrete type B0 (1:3:6 )(using 12.5mm graded aggregate ,etc complete all as specified as directed.

S&F Pressed steel frames of size 105x60mm, made of 1.25mm thick sheet, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, incl filling hollow of frame with plain cement concrete type B0 (1:3:6 )(using 12.5mm graded aggregate etc complete all as specified as directed

S&F MS Framed work Fe-410W Gde E-250 quality A as in doors or gates of angles or other sections with gusset plates rails, brases etc complete drill for steel sheeting or other covering complete all as specified and directed.

S&F Steel windows made up of box steel section of 16 gauge ms sheet ub outer frame, shutter farame and centre frame with outer side glazed shutter and inner side wire mesh shutter fixed as shwon in drg consisting with two nos pintol hinges 100 mm long, two nos stove enemaled tower bolts 150 mm long and one no steel handle, deovitailed are welded each panelan complete with necessary cleats and stopers all as specified as directed.

Steel ventilator made up of box steel section of 16 gauge MS Sheet frame, partly fixed and partly openable with outer glazed shutter and inner side wire gauge shutter consisting with 2 Nos pintos hinges 100mm long 2 Nos stove enamelled tower bolt 150mm long and 1 Nos steel handle dovetailed or welded with each shutter complete with necessary cleat and stopper complete all as specified and directed (MS Gaurd bar/grill work will be measured and separately.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins or spring clips and providing and fixing new clips or pins, all as specified.

S&F sheet glass ordinary quality and glazing with oil putty in square n. exc 0.50 Sqm in each pane 3mm thick all as specified

All as per item No 29 above but pin headed

S&F Galvanised mild steel wire cloth 0.56mm nominal dia of wire and avg width of aparture 1.18mm complete all as specified and directed

All as per item No 31 above but fixed in repairs.

S&F aluminium anodised barrel tower bolts of extruded section with 150 mm long bolt, all as specified .

S&F aluminium anodised barrel tower bolts of extruded section with 100 mm long bolt, all as specified .

S&F in repair MS sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, 250 mm long.

S&F Alu alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, 250 mm long.

S&F MS butt hinges 100mm long medium weight cold rolled mild steel etc

S&F 300mm long ordinary rat tail rod pattern spring incl roller and plate complete all as specified

S&F aluminium handles cast type, anodised, 150 mm size complete

S&F aluminium handles cast type, anodised, 100 mm size complete

S&F 100mm long Hasp and staple aluminium anodised including bolt to hinge plate and fixed with screws.

S&F in repair Tubular Towel rail 20mm dia, D type, 60cm long between flanges of brass chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleats all as specified.

S&F for Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work for water tanks and similar work conforming to Fe 290 Gde-E-165 all as specified .

S&F bands, straps, supports or stays for rain water, ventilating pipes, incl bolts if required clampsof suitable dia for the any type of pipe made out of 40x3 mm MS flat with all necessary fitting fitted to wall with 2 nos hold fastners all as specified and as directed.

Mild steel TMT bars 10mm dia and over (and flat iron where quered),cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mmdia or securing with clips or welded to flat iron complete all as specified.

M&L TMT bar 6 mm to 8mm dia and over cut to length,bent to shape required incl cranking bending and binding with and including mild steel wire(annealed) not less then 0.9mm dia

M&L 18-20 mm thick for Granite work (table rubbed and polished) in steps, jambs,pillars, window-cills, cooking plat-forms and like in cement mortar (1:4) incl pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite incl screed bed or bedding layer of mortar 20mm thick in cement mortar 1: 4 for laying floor finishes complete all as specified

M&L for Glazed cermic coloured tiles 300x450x 7mm thick on vertical surfaces of wall set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick rendering in CM (1:4) backing of wall tiles such as dado/skirting in vertical surface including dismantling of existing old wall tiles complete all as specified and as specified.Make:-Somany/NITCO

M&L for Non skid ceramic coloured ceramic tiles 7 to 8mm thick (squqare/ rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM (1:4) including dismantling of existing old floor tilescomplete all as specified.Make:-Somany/NITCO

M&L Non skid ceramic tiles 7-8mm thick in floors area exc.0.11sqm and not exc.0.18sqm set and jointed in neat cement slurry and pointed in coloured cement to match colored tiles incl over 15mm thick screed bed or bedding layer of CM (1: 4) for laying floor finishes including dismantling of existing old floor tiles all as specified and directed. Make:-Somany/NITCO

M&L Non skid ceramic tiles 7-8mm thick in floors area exc.0.11sqm and not exc.0.18 sqm on vertical surfaces such as skirting/dados etc, set and jointed in neat cement slurry and pointed in coloured cement to match colored tiles incl over 10mm thick in CM (1:4) on brick or concrete surfaces of finished rough to receive the tiles including dismantling of existing old wall tiles all as specified. Make:-Somany/NITCO

M&L for machine cut kota stone slab 18-20 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete incl screed bed or bedding layer of mortar 20mm thick in cement mortar 1: 4 for laying floor finishes complete all as specified..

M&L for machine cut kota stone slab 15-16 mm thick in riser of steps, skirting,dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete incl 10mm thick rendering in CM (1:4) backing of wall tiles such as dado/skirting invertical surface complete all as specified and as specified.

M&L 25mm thick Plain cement concrete type B0, 1:2:4 using 12.5mm graded aggregate as in flooring, roof padding etc complete all as specified and directed.

Water proofing treatment to floor & vertical surfaces of sunken portion complete comprising the following: - (a) After demolition of floor & lime concrete etc. remove all loose particles along with existing water proofing treatment (any no. of layers) with wire brushes and cleaning the surfaces with water. (b) Brushing cement slurry with 1.2 kg of cement per square metre duly blended with & including water proofing compound. (c) 15 mm thick (Average thickness) plaster in cement mortar (1:3) mixed with WP compound on sunken surface including walls. The corner of sunken portion shall be rounded in concave shape and adequate slope shall be made during plastering to accommodate sump pipe and curing the sunken portion with water minimum for 48 Hrs by ponding. (d) Applying self adhesive type APP based polymeric membrane minimum weighing not less than 3.6 kg/ Sq. m and minimum 3 mm thick reinforced with polyester non-woven fabric (weight not less than 150 gm/Sq. m),(e) M&L for PCC 1:7 :12 for fillin of sunken portion after conceling all menbrane and sealing all joints to the entire with broken bats and light weight all as satisfaction of Engineer-in-Charge. MAKE: LAFARGE, TEXA, STP, BENGAL AQUAFLUX. lAFARGE, TEXA, STP, BENGAL AQUAFLUX.

M&L for 15 mm thick cement plaster in cement mortar 1:6 on brick or concrete surface etc. on wall finished even and smooth without using extra cement, all as specified .

Supply only liquid water proofing compound (Makes :Pidilite Industries / Impermo /Snowcem India Ltd / Sika )

M&L for 10mm thick cement plaster on brick or concrete surfaces, as in ceiling / facia / chajja etc. in cement mortar 1:3 finished even and smooth without using extra cement, all as specified .

M&L for extra over rendering or plastering for work in isolated widths or in widths not forming part of general palastering such as in bends, sunk panels, cornices, skriting, drip moulds and similar work n.exc 15 cm in width or girth including cutting edges, all mitres and stopped ends etc. (Note: Water Proofing compound shall be measured and paid for separately)

M&L for 15 mm thick rendering on fair faces of brick work or cement concrete surfaces in cement mortar 1:4, finished fair and even without using extra cement incl mixing of water proofing compound complete all as specified. (Note: Water Proofing compound shall be measured and paid for separately)

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc.

M&L Three coats of white wash on newly plastered surfaces of ceilings including preparation complete all as specified.

M&L Two coats of oil bound distemper on newly plastered wall surfaces over a coat of alkali resistant primer including preparation complete all as specified and as directed.

M&L Two coats of cement base paint on newly plastered wall surfaces over a coat of alkali resistant primer including preparation complete all as specified and as directed.

Complete removal of existing tretment and prepaition of surface of any sescription compllete all as specified

Preparing new plastered surfaces of walls and applying two coats of exterior emulsion paint (Weather Coat) over a coat of priming paint on roof boarder, drops, fins, chajja / roof facia,column,wall etc, complete all as specified

M&L Two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer including preparation of new steel surfaces of any description, over 10 cms in width or girth not otherwise described

M&L Two coats of synthetic enamel paint over a coat of pink primer including preparation of new wooden surfaces of any description, over 10 cms in width or girth not otherwise described

Taking up or down steel tubing with connections for cleaning for refixing or removing to store yard complete of bore 15mm, all as specified .

Taking up or down steel tubing with connections for cleaning for refixing or removing to store yard complete of bore 20mm, all as specified .

S&F 15mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings all as specified.

All as per item No 71 above but fixing only

S&F 20 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings

All as per item No 73 but fixing only

S&F in repair Bib taps,long body, fancy type,chromium plated with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm, all as specified.

S&F in repair Angle valves fancy type, chromium plated, cast copper alloy, with long shank and cup screwed for iron pipe or for unions of bore dia 15mm and fixed, all as specified

S&F in repair Stop valves fancy type, chromium plated for iron pipe or for unions of bore dia 15mm and fixed, all as specified

S&F in repair Shelf of Corner glass shelf fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum wight 300 grms)complete all as specified.(CAT NO:-BEA-46, Make: Prayag)

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm long

S&F Gun metal globe or gate valves, with iron wheel head screwed both ends for iron pipe of 20 mm dia, all as specified and directed

S&F in repair Gun metal globe or gate valves, with iron wheel head screwed both ends for iron pipe of 20 mm dia, all as specified and directed

S&F Gun metal globe or gate valves, with iron wheel head screwed both ends for iron pipe of 15 mm dia, all as specified and directed

S&F in repair Gun metal globe or gate valves, with iron wheel head screwed both ends for iron pipe of 15 mm dia, all as specified and directed

S&F in repair Brass chromium plated shower rose with arm 225 mm size with or without swivel joints, any size incl fixing to steel pipe or union complete all as specified.

S&F in repair Vitreous china squatting pan of pattern Orissa Pattern size 580x 440 mm white with ‘P’ or ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe fixed in repair including placing in position in floor and embedded in cushion of PCC 1:7:12 type E-1 and finishing the top surfaces to match with the existing flooring

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm boul size 405mm x 354m x 203mm.

S&F in repair stainless steel Soap dish fixed to plugs chromium plated brass screws, all as specified.

S&F in repair PVC (Plastic polymer Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete including taking down by dismantling the existing unserviceable cistern of any description.

S&F in repair Waste coupling, 32mm dia, of PTMT (half or full threaded) .complete all as specified.

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement, 75mm diameter of outlet, all as specified.

Dismantling of cast iron, CI/AC / PVC pipes including all fittings and accessories, of 100/75 mm dia and in any position all as specified.

S&F PVC(SWR) pipes, 75 mm external dia double socketed in any length with rubber joints, fixed to walls/under floor with PVC brackets/clips including under floor will be coverd in PCC 1: 3:6 as complete all as specified(with epoxy joint)

S&F PVC(SWR) pipes, 110 mm external dia double socketed in any length with rubber joints, fixed to walls/ under floor with PVC brackets/clips including under floor will be coverd in PCC 1: 3:6 as complete all as specified.(with epoxy joint)

S&F PVC(SWR) bends suitable for 110 mm external dia (with epoxy joint) complete all as specified.

S&F PVC (SWR) bends suitable for 75 mm external dia complete all as specified.

S&F PVC (SWR) junction single, (single T) equal or unequal of 75mm dia.(with epoxy joint)

S&F PVC (SWR) junction single, (single T) equal or unequal of 110mm dia.(with epoxy joint)

S&F PVC (SWR) junction single, (double T) equal or unequal of 75mm dia.(with epoxy joint)

Add to item No 94 & 95 if provided with over access door

Add to item No 96,97& 98 if provided with over access door

S&F in repair of vitreous china Wash basin white type of size 550x400 mm including CP waste fitting&waste pipe etc with sutiable fixing arrangement to wall including taking down old complete all as specified and directed.

Dismantling water tanks RCC or PVC 500 Ltrs capacity

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of Capacity 500 litres all as specified .(Make:- vectus/Syntex)

S&F Ball valve, high pressure with PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or fixed of size 20 mm bore, fixed in repairs.(Min Wt 20mm- 210 gms)

S&F in repairs Ball valve, high pressure with PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or fixed of size 20 mm bore, fixed in repairs.(Min Wt 20mm- 210 gms).

S&F in Repair PVC waste pipe 800mm long suitable for 32mm dia waste coupling complete all as specified.(CAT NO:-3272, Make: Prayag)

S&F PVC powder decorative mild steel curtain rod of 25 mm dia with brackets both side of globe in repairs all as specified and directed by Engr-in-charge.

S&F in repair stainless steel peg set of six sutable size of length complete etc.

Diasmantling wrought iron or mild steel work of any description not otherwise provided for.

Taking down existing roof treatment of any description and any type all as specified and directed by Engr-in-Charge

Roof tratetment for non -accessible Roof:- 15 mm thick cement plaster in cement mortar 1:4 on roof surfaces finished even and smooth without using extra cement, including water proofing compound over Priming the roof surface with bituminous primer conforming to IS-3384 @ 0.30 ltrs/Sqm and applying a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.20 Kg/Sqm and thereafter provide polymeric water proofing membrane (five layered) of weight not less than 3 Kg/Sqm with centre layer core of 90 micron high molecular density polyethylene film followed by another coat of semi hot blown 85/25 grade bitumen @ 1.20 Kg/Sqm blinded with fine sand in dry condition @ 0.50 Kg/Sqm Top surfaces of roof after carrying out treatment as specifed hear-in -above shall be provided with 2 coats of aluminium paint over a coat of primer as per manufacturing,s indstruction complete all as specified and directed.

Taking down old PCC tiles from roof and removing bedding at any position all as specified and directed

Roof tratetment for accessible Roof:- 15 mm thick cement plaster in cement mortar 1:4 on roof surfaces finished even and smooth without using extra cement, including water proofing compound over Priming the roof surface with bituminous primer conforming to IS-3384 @ 0.30 ltrs/Sqm and applying a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.20 Kg/Sqm and thereafter provide polymeric water proofing membrane (five layered) of weight not less than 3 Kg/Sqm with centre layer core of 90 micron high molecular density polyethylene film followed by another coat of semi hot blown 85/25 grade bitumen @ 1.20 Kg/Sqm blinded with fine sand in dry condition @ 0.50 Kg/Sqm all as specified and directed.

M&L Cement concret tiles with cement and no pigment 30 cmX30 cm x20mm thick machine pressed set jointed and including 15mm screed bedding in CM 1:4 as pointed in neat cement slurry in flooring as cut and poslished all as specified.

Making benching with PCC (1:2:4) type B0 (12.5 mm agg) using WPC along side wall adjoining to roof in concave shape complete all as specified.

S&Fin repair stainless steel plate racks of size 750mm x 900 x 250mm and thickness of SS strip of Not less than 0.50mm Thick fixed on wall etc complete all as specified.

Providing Kitchen cabinet /Cupboard shutter in required size at site made out of 18mm thick MDF made out of 18mm thick one side decorative lamination PVC sheet complete all required etc. The panels shall be fabricated using adhesive and secure as required. All edges shall be covered with 2mm thick edge bonding taps or 90⁰ edge bent finish as per manufacturers instructions.

S & F Continuous (piano) hinges,mild steel, bright finish or electrogalvanised

S&F in repair 40/50mm dia sink coupling PTMT (half or full threaded) complete all as specified and directed

M&L for 100mm bore galvanized steel water pipe medium grade 0.90m length including demolition of brickwork any description and making good with sub class 'B' bricks built in CM (1:4) and 15mm thick rendring on both side of brick work in CM 1:4 finished fair and even without using extra cement including mixing of water proofing compound complete all as specified.

S&F pillar taps, cast copper alloy, with capstan heads, chromium plated screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed.

PARAS RAM ASGOTRA AND SONS

NARESH KUMAR KHAJURIA

DAVINDER SINGH

M/S PEE BEE SALES CORORATION