Repair and maintenance of LT Panels, overhead conductors and connected accessories under GE Gurdaspur.

Amount

Excavation in trenches in soft/ loose soil including cutting road surfaces n.exc 1.5 mtr wide and n.exc. 1.5 mtr in depth for poles, stay, cable, pipe etc and getting out all as specified.

Returning, filling in, including spreading, leveling,watering and well ramming in layers each n.exc 25 cm thick in soft loose soil all as specified.

Removal of excavated soil to a distance not exceeding 50 mtrs and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Supply and lay brick common burnt sub class "B" old size (compressive strength not less than 75 kg per sqcm) for protection of cable laid in trenches for under ground cable all as specified.

M & L for sand cushioning trenches using fine sand to under ground cable, laid in two layers 15cm before laying the cable & 8cm after laying the cable complete all as specified and directed.

M&L for road cutting including excavation returning filling in spreading leveling , well ramming in layers, soiling with, broken boudders/ stones, WHB 7.5 cm thick coarse aggregate received from dismentling the existing road, premix, carpeting 25mm thick using mady mate material . rolled & compacted for road patch repair work, section/ cross section area of cuttng complete all as specified and directed.

M&L for cable protection GI tubing light grade fixed long the pole/along the wall of size 50mm bore with necessary clamps all as directed.

M&L for cross arms in replacement , bracing, supports, clamps and brick plates, fabricated from staructural steel section including nut bolts washers including welding, bending , cold or hot drilling holes for bolts in any shape or size as indicated in drawings or as directed, including two coats of aluminium paint over a coat of red oxide all specified.

M & L lightening arrestor in replacement expulsion type for out door use complete with all fitting transmission class discharge capacity 65 Kilo Amp suitable for 11000 volts including bracket, clamps, nuts, bolts washer and connection to each wire complete all as specified. Make-Rashtria/Oblum.

Surface dressing by cutting grass, thorn bushes and congress grass upto the root level surrounding the installation incl the same not less than 200 mtr away all as directed by Engineer- in -Charge.

Supply and laying in replacement XLPE insulated armoured (under ground) heavy duty electic cablewith stranded aluminum conductor 1100 volts grade of cross- sectional area 25 Sqmm 4 core laid in trenches/ducts/through pipes/in floor road/along the pole etc all as specified & directed by Engr-in-Charge. Note : Excavation earth work, brick protection and cushioning shall be measured & paid separately.

All as per srl item No. 12 here in before but 16 Sqmm 2 core

All as per srl item No. 12 here in before but 10 Sqmm 2 core

M&L for disconnecting the existing transformer dismantling rthe existing foundation of the transformer and temporary arrangement of the connecting the existing transformer to feed the user and making foundation of outdoor type transformers PCC block platform of size 3.0m x 3.0m x 1.5 mtr in cement mortar 1:6 over thick foundation bed in PCC 1:4:8 type D-2 (using 40mm graded stone aggregate of 50mm thick coping in PCC1:2:4 type B-1 (using 20mm graded stone aggregate) over platform and 15mm thick rendering in CM 1:6 to exposed surface of PCC and applying three coats of white wash including making electrical connections, earthings connection etc and testing the transformer for smooth functioning complete all as directed by Engineer-in-Charge.

M&L for mild steel corrugated sheet of 1.6 mm thickness for covering the cable trench covers including taking out the old trench covers ad making proper arrangement for the new cable trench covers complete all as specified and directed by Engineer-in-Charge.

Providing PCC 1:4:8 type D:2 using 40mm graded crushed stone aggreate as in foundation for pole/stay assembly foundation coping of poles etc.

Providing PCC 1:2:4 type B:2 using 20mm graded crushed stone aggreate as in foundation for pole/stay assembly foundation coping of poles etc.

S&F in replacementment of sign board made of 3mm thick high intensity retro reflective sheeting of approved shade and writing information logo etc fixed both side on 2mm thick aluminium sheet framing with stainless steel tube of 40mm dia (Grade -304) and mounting on 02 Nos stainless steel tube of 50mm dia (Grade -304) of 3 mtr hight (Note size of board approx 4'x4' ) including fixing of board on ground/ PCC platform with PCC of suitable ratio, writing details will be given by Engineer-in-Charge and before manufacturing the board the approval should be taken for content of the board as per specified and directed by Engineer-in-Charge.

S&F of decoative garden light fittings of 25 watt bollard type of CCT more than 5000K of product code PGR0201007 in polycab or equivalent in C&S/L&T/ Philips including light pole of dia as per bollard dia of height approx 4 mtrs including excavation making foundation of poles , electric connections etc complete al as specified and directed by Engineer-in-Charge.

S&F MCCB 250 Amp 25 KA 415 volt FP. Make :- Havells or equivalent in Legrand/ ABB/ L&T/ Indo Asian/ HPL.

S&F MCCB 100 Amp 16 KA 415 volt FP. Make :- Havells or equivalent in Legrand/ ABB/ L&T/ Indo Asian/ HPL.

M&L for LT cable straight through joint kit of size 240 sqmm 3.5 core complete all as specified and directed

M&L for LT cable straight through joint kit of size 185 sqmm 3.5 core complete all as specified and directed

M&L for LT cable straight through joint kit of size 150 Sqmm/ 120 Sqmm 3.5 core complete all as specified and directed

M&L for LT cable straight through joint kit of size 95 Sqmm 3.5 core complete all as specified and directed

M&L for reflective tape Red and Yellow colour 50mm Red. Note : 2 run of yellow colour and 1 run of red colour will be considered as one run all as specified and directed.

M&L for synthetic chequered insulated mat, ISI marked of size 2m x 1m x 19mm conforming to IS-15652/2006

M&L for repairing of LT pannel of any make type/ size an including Gas/ Arc welding, fill up rusted patches with 3mm MS sheet lugs, Lt aluminium conductor cable lead and bus bar of suitable capacity, front and rear door lock set replace, RYB and black colour wise insulation tape for bus bar, nut bolt, washers , hinges, grinding and scraping of old paint/ rust etc by wire bursh from body of LT pannel and apply base material for smooth surface and applying 2 coat of synthetic enameled spray paint over one coat of primer after denting etc complete all as specified and directed by Engineer-in-Charge.

M&L mild steel of Fe-410W Gde E-250 quality for framed work as in doors or gates of angle other sections with gussets, plates, rails, braces etc complete drilled for fixing of steel sheeting or othercovering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges of steel hanging door fittings (exclusive of steel sheeting or other covering running rails and guides and handing also fasteninbg and fixing complete used for making of brackets, nuts, bolts, washers round bars different sizes rails for chain link fencing ladders stone and etc all as directed by Engineer-in-Charge.

Excavating in post holes( or similar holes) each n exc 0.5 cu.m. getting out, returning,filling in and ramming earth of broken rubble mixed with earth around , in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface complete all as specified and directed.

S&F of 3.15mm dia galvanised steel wire chain link fencing of grade 100mm x 100mm fixed on MS steel angle iron, including binding wire/ wine wire etc complete all as specified and directed.

M&L cradles hexagonal/ rectangular, fabricated with galvanised steel wire 3.15 or 4mm dia for road crossing, building crossing and any area all as specified and directed and specified by Engineer-in-Charge.

S&F in replacement switch air break gang operated switch tripple pole machanically operating mounted on insulator and steel frame with operting machanism worked from ground level for current rating up to 200 amps and working pressure of 11000 volts grade consisting of 4 insulator per pole with 20mm dia GI medium grade operating handle and locking arrangements fixed with down rod operating brackets all as specified and directed by Engineer-in-Charge.

M&L for spacer with 3 ways of insulated material for overhead ACSR or any type of conductors at places directed by Engineer-in-Charge.

M&L for spacer with 4 ways of insulated material for overhead ACSR or any type of conductors at places directed by Engineer-in-Charge.

M&L Earthing complete with galvanized steel earth plate electrode 600cmx600cmx6mm thick burried directly in ground ( earth pit not less than 2.25 mtr deep below the ground level) with edge of the plate not less then 1.5 mtr below the ground level, connection to GI galvanised iron strip 25mm x 4mm as earthing lead by means of bolts/ nut & washers of GI or steel all shown in electrical plate No 5 of SSr Part-I connection to feeder piller all as specified including watewring GI Pipe 40mm bore medium grade PCC chamber using PCC 1:3:6 type C2 C1 cover funnel & wire mesh complete all as specified and directed by Engineer-in-Charge.

M & L of preparation of old painted surfaces of electric pole covered by dust and other deposited materials by cleaning form steel tubular pole of length upto 9 metres cross arms, bracing , clamps etc and painting with one coat of aluminum paint retaining and repainting marking on pole and replacement of reflective band of RED- YELLOW- RED altermate coloured 3 numbers complete all as specified and directed

M&L for preparation of old cement based paintged surfaces of RCC poles 9 to 11 mtr height cleaning the dust and other deposited materials and painting with one coat of exterior weather coat paint of approved make and colour retaining and repainting marking on pole and replacement of reflective and of RED- YELLOW- RED altermate coloured 3 numbers complete all as specified and directed

Sharma Electrical and Engineering Works

JAI DURGA CONSTRUCTION CO