Reconstruction of breached embankment at Ch. 2.51km, 2.55km, 2.60km, 6.28km, and 6.55km including improvement of R/B embankment of Rupahi Package 2

Amount

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses ans 1204 A) With Crushed Stone II) P.C.C. grade M 20(i) Nominal mix (1:2:4)

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 A) With Crushed Stone (IV) RCC Grade M 25(i) for height upto 5m.

Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/Jindal steel/Shyam steel/RINL)in substructrue complete as per drawings and technical specification Clauses 1002 1005 1010 & 1202.

Providing and laying flooring laid over cement concrete bedding completes as per drawing and technical specification Clause 1303 III) Brick on edge laid in cement mortar (1:3)

Providing form work in ordinary timber plabnking so as to give a rough finish including centering, shuttering, strutting & propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.00M and removal of the same for in-situ reinforced concrete and plain concrete work in, foundation, footings, bases of column, pile cap, raft and mass concrete works etc.

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including settingout, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. V) Marshy soil

Providing and laying of boulder apron laid in wire crates with 4 mm dia GI wire conforming to IS:280 and IS:4826 in 100 mm x 100 mm mesh (woven diagonally) including 10 per cent extra for laps and joints laid with stone boulders weighing not less than 25 kg each as per drawing and technical specifications Clause 1301

Bored cast-in-situ M35 grade R.C.C. pile excluding reinforcement complete as per drawing and technical specifications and removal of excavated earth with all lifts and lead upto 1000 m. including providing plasticiser (Masterplast PL-1/SPL-2 or equivalent), air entraining and water reducing plasticiser ( asterplast PAE or equivalent) and accelerating plasticiser (Masterplast ACPL or equivalent) conforming to IS-9103-1999 (Pile diameter-750 mm)

Sluice gate(Mechanical part) M.S.plate, 6 mm for.shutter skin

M.S.channel,150 x 75mm for stiffener

J’ type rubber seal, 125mm size

‘J’ type rubber seal corner, 125mm

M.S.Flat(50x6)mm for fixing Rubber seal

M.S.plate, 10mm for.shaft & counter wt. bracket,base support

Nuts & bolts (assorted size)

M.S. washer (assorted size)

M.S.electrode,8 SWG

Filled Acitylene. gas

Filled Oxygen gas

Red Oxide primer

Antisol red oxide paint

Turpentine oil

Painting brush,3” size

Wire brush

C.I.rollers with centre hole 20mm including suitable collar as directed including fine finishing of size,100 x 150 mm

F shapped roller bracket made of 10mm thick plate of size 75 x 200mm with hole as directed to accommodate the above rollars

Roller pin of length 150mm 7dia 16mm

M.S.channel,200 x 75mm for Guide & bottom

M.S. angle,(50x50)mm for anchoring

Guide channel separator stud

H.S. Diesel

M.S. Shaft ( Best Quality ) 50 mm dia

M.S. plate for Plateform

M.S. Angle 75 x75 x 6 mm

Refilled Oxygene gas

Refilled Acetylene gas

Thread cutting 2 TPI including fine finishing and making hole in one end as per direction. 63 mm size

C.I. Boss with internal thread cutting 2 TPI making groove for bearing slot for lock plate & 1.5" drill for providing handle as per direction for size : 125 mm x 150 mm

G.I. pipe for Boss handle & distant tube size 25mm

M.S. base Plate 300 x 300 x 10 mm

M.S. lock Plate 300 x 300 x 8 mm

H.D. Thrust ball bearing 50 mm

Clamp for lock plate

Hire charge of crane with capacity 8 tonne with operator excluding fuel & lubricant.

Casual labours for helping works of lifting and carrying sluice gate materials, other allied works etc. @ 8 nos for 10 days

Arc welding cable 600 amps

Jati bamboo

Coir rope

Mobile for generators and machineries

Grease

Waste cotton

Gas cutting hose pipe , 12 mm dia ( Red & Black )

Leather hand gloves

Arc welding mask

Gas cutting nozzle

Hacksaw blade 1.5" x 12 " ( double ended)

Nylon rope

SURAJIT ROY PRASANTA DEY JV

OE-ANPL (JV)