SPL REPAIR TO BLDG NO T-4,T-5 AND T-6 (SINGLE LIVING JCOS ACCN ) AND SPL REPAIR TO REPLACEMENT OF RUSTED CI/GI PIPE WITH DI/PPR PIPE AND ALLIED WORKS AT VARIOUS LOCATIONS AT BENGDUBI MIL STN UNDER GE BENGDUBI

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering/ cladding to wall fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S & installation and testing of Electric water heater , storage vertical type BEE 4/5 star rated, 25ltr capacity 240 volts 50 Hz comprising of high wattage heating element for instant heating , extre Mild steel with glass lined coated inner tank , rust & shock proof ABS outer body, non-ferrous pressure plate with & including provn of 4 Nos grouting bolts suitably flushed to wall or any other surface including electric connection with 3 core PVC insulated , sheathed, stranded copper conductor cable/flexible chord and one no 15 amps 3 pin plug top etc complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and as directed.

S&F mild steel rolled sections [Fe 410-W (Gde E-250) quality - B] as in roof trusses (framed), trussed, main and cross beams, hip and jack rafters, purlins, Gusset plate and base plates, where connected to common rafters and running rails, distance pieces, cleats, guides for sliding doors; fixed with angle cleats or other connecting plates, framing for cladding, staging for water tanks, nuts, bolts, washers etc,includng welding or riveting etc, complete all as specified and as directed.

M&L for the Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed.

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLSH cable of size 4.0 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLSH cable of size 4.0sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 25 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces including taking down of existing old submain wiring, complete all as specified and as directed. Note:- For payment purposes, 2 runs of main cable (each of 1RM) 1 run of earth continuity cable (1RM) and one run of conduit (1RM) all together shall be considered as "1RM".

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in vertical Surface etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 10mm thick screed bed in CM (1:4), complete all as specified and as directed.

S & F 4mm thick Non-asbestos fibre cement decorative/designer building boards to steel frame work with screws in ceiling (flat and/or slopping) and including jointless finish with & also including joining compound and tape as per manufacturer instructions, including dismantling of wall and ceiling boards complete all as specified and as directed. Notes :- (i) The board shall be confirming to IS-14862 and shall be manufactured from the homogeneous mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process.(ii) Aluminium frame work shall be measured and paid for separately.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortar backing coat in CM (1:4), complete all as specified and and as directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and as directed.

M&L for granite (of any type) 20mm thick (Table rubbled and mirror polished ) in steps, jambs, pillars, window-cills, cooking platform etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 20mm thick screed bed in CM (1:4), complete all as specified and directed.

S&F factory made 1.25 mm thick pressed steel frame of size 165 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after prepation of the surfaces, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, disposing off the retrieved debris outsde the premises, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, disposing off the debris outsde the premises, complete all as specified and as directed.

S & F powder coated aluminium frame for doors window, ventilator with one or more rebates including joining cleat for fixing etc .

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed.

S&F 2 module starter switch 25Amps, 240 volts including Modular Metal Flush box and cover plate, complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & show on drawing for SI NO 8101 on Sr. Page No181 of SSR Part -II and as directed.

S&F Factory made 30mm thick flush shutter solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and as directed.

M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 35 mm thick glazed and skeleton shutters, open rebated and prepared to rceieve glass, gauze, etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F 100mm size butt hinges, heavy weight, cold rolled, mild steel, complete all as specified and as directed.

S&F 150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt, 200 mm long of extruded section, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt, 150 mm long of extruded section, complete all as specified and as directed.

Taking down cement plaster on brick or concrete surfaces etc, including raking out joints, hacking for key, scrubbing down with water etc, and also including removal of rubbish off the premises, complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar (1:3), on concrete surfaces of ceiling , finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:6), on brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surfaces finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

Supply only integral water proofing compound, complete all as specified and as directed.

Taking down steel tubing & connections including cleaning for refing serviceable pipe or removal balance pipe of 15 mm dia bore complete all specified .

Taking down steel tubing & connections including cleaning for refing serviceable pipe or removal balance pipe of 20 mm dia bore complete all specified .

S&F laying of CPVC pipes SDR 11& plain CPVC SDR 11 20mm outer dia laid in trenches/wall complete all as specifed

S&F laying of CPVC pipes SDR 11& plain CPVC SDR 11 25mm outer dia laid in trenches/wall complete all as specifed

M & L for making good wall top for roof sheet or under cills or over arches, lintels and bressummers including all pinning when necessary with CM (1:6) Complete all as specified and diercted

S&F Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe of 20mm bore (Minimum weight 210 grms), complete all as specified and as directed.

S&F hard drawn steel wire fabric (weight not exc.4kg/Sqm) fixed in tank caging, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia, complete all as specified and directed.

Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

S & F aluminium powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators, partitions with extruded built up standerd tubular sectiond/appropriate Z sections and other sectionsapproved make conformunf to IS:1285 fixing with dash fastners of required dia and size includig necessary filling up the gaps at junctions i.e at top, bottom and sides requried EPDM rubber/neoprene filling up the gaps at junction with one or more rebates including joining cleat for fixing etc. aluminium sections shell be smooth, rust free ,straight, mitred and jointed mechanically wherver required including beading gor glazing/paneling complete all as specified complete all as specifie

S&F in repair vitreous china wash basin, 1st quality, white, flat back, approx size 550x400mm excluding taps but including 32 mm bore brass chromium plated waste fittings, 32mm bore PVC waste pipe, MS brackets, complete all as specified and as directed.

S&F in repair sink with drainage board made of 0.80 mm thick sheet of stainless steel (Bronze range super steel 204 : Matt) for kitchen or laboratory with and including plugs, washers, 32mm bore brass chromium plated waste fittings, 32mm bore PVC waste pipe, also including bedding in cement mortar (1:3) on dwarf wall or including providing mild steel cantilever brackets and connecting union to pipe, overall size 915mm x 460mm with bowl size 410mmx 330mm x 160mm complete all as specified and as directed.

S&F anodised aluminium snap grid of size 605x605mm frame work for false ceiling hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out GI flat iron 40x3mm size 60mm long and fixed expansion hold fasteneners 12.5mm dia and 40mm long, complete all as specified and as directed.

S&F in repairs tubular towel rail, 20mm dia, D type, brass chrormium plated, 600mm long between flanges, complete all as specified and as directed.

S&F 4mm thick sheet plain glass pin head type and glazing with oil putty in squares nexc 0.5 Sqm in each pane etc, complete all as specified and as directed.

S&F in repairs bib tap, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed.

All as above item no 55 but tap 2 in 1 of 15mm bore complete all as specified and as directed.

M&L for Brickwork with fly ash Bricks(old size), straight or curved on plan to any radius in half brick walls built in Cement mortar (1:4), complete all as specified and directed

S&F in repairs Pillar taps with Aerator, fancy type, cast copper alloy, with long swan neck , chromium plated, screwed down high pressure,

with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, complete all as specified and as directed.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 600 mm, complete all as specified and directed.

S & F in repair 32 mm bore low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm laid in floors/ trenches etc, complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm X 600 mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, PCC (1:3:6) type C-1 with 50 mm thick Pre-cast RCC (1:2:4) type B-1 cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (Medium grade), wire mesh, aluminium lugs, complete in all respect, GI earth strip protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 m and necessary testing on completion, including dismantling old unsv ones complete all as specified . Note: GI earth wire 4sqmm dia and 15mm bore protection pipe upto 7.5m from earth plate is deemed to be included in the rate quoted be contrator.

S & F in repair 75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed.

S & F in repair PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F in repair PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints,fixed in wall complete all as specified and as directed.

S&F 75mm bore PVC (SWR) bends (any radius) with and including rubber ring with access door, complete all as specified and directed.

S & F PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints,fixed in wall complete all as specified and as directed.

S&F 110mm bore PVC (SWR) bends (any radius) with and including rubber ring joints, complete all as specified and directed.

Demolition of cement concrete (un-reinforced ) in ground floors and pavings n exc 15 cm thickness (below or above ground level) including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate), as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of (3:1), complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in coping, bed block for filling hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones bed plates,water troughs and the like including weathering, slightly rounded or chamfered angles & throating as including form work as requried complete all as specified and as directed.

M&L for Brickwork with fly as Bricks(old size), straight or curved on plan exc 6m mean radius built in Cement mortar (1:6), complete all as specified and directed

S & F in repair jet spray with flxible pipe 15mm bore stainless steel complete all as specified and as directed.

S&F in repair mild steel helical door spring 300mm long, ordinary rat tail rod pattern springs including roller and roller plate fixed with screw to wooden frame or with welding to steel frame, complete all as specified and as directed.

M&L for complete removal of existing treatment from the internal surfaces of wall etc, applying two coats of wall care Putty (minimum thickness of two layers shall be 2mm) and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coat of white washing, complete all as specified and directed .

M&L for preparation of newly plastered wall surfaces and applying two coats of cement based paint over a coat of primer, complete all as specified and directed.

M&L for preparation of old decorated wall surfaces and applying two coats of cement based paint including brooming down or steel wire brushing down smoke spot,moulds, moss and efforescent and trading oil and greasy spots etc, complete all as specified and directed.

S&F in repair angle/stop cock, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed for iron pipe or for unions of 15 mm bore, complete all as specified and as directed.

M&L for preparing new Plastered surfaces of walls duly applied 2mm wall care Putty and there after applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L for preparing new wooden surfaces of any description not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed .

S & F in repairs stainless steel curtain rod of 25mm dia including six nos curtain ring per running meter complete all as specified and as directed.

S & F finial fancy type for curtain rod in pair etc complete all as specified and as directed.

M&L for 75mm thick plain cement concrete (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in sub-base of flooring, etc, finished concrete surfaces even and rough to receive cement screed, complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick ompacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

Taking down CI pipes 100 mm dia from trenches/walls/floor etc complete including joints all as specified and directed.

Taking down carefully existing aluminium point wiring (light / fan / socket or power point) complete, with all fittings such as switch socket combination, switches, sockets, regulator, ceiling rose, utility light fittings and lamp holders etc and making good the disturbed surfaces of walls, roof and floor etc to match with the existing specification, complete all as specified and as directed.

S&F in repair rotational moulded polyethylene water storage tank 500ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position complete all as specified and as directed.

S & F floor mounted one piece water closet ceramic western toilet/commode/European commode square with soft close seat cover white including connection to drain (or outgoing pipe) and to flushing pipe , anti syphonage pipe etc.

Taking down old/unservicable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/Main switch including old unservicable MCCBs/MCBs,isolators,etc and making good the disturbed surfaces complete all as specified and as directed.

All as per item No 87 here-in-before but for one 3pin 5 Amp switch socket outlet, independent board , complete all as specified and as directed.

M&L for point wiring for one light point/ one fan point/ one exhaust fan controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made anodized pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes suitable size and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM 1:3 to for One light /Fan point controlled by one, one way switch match with the adjoining surfaces , complete all as specified and as directed.

S&F Modular switch 1 way 6A, 1 module, complete all as specified and directed.

S&F Modular switch 1 way 16A, 1 module, complete all as specified and directed.

S&F Modular socket 6A , 2/3 pin combined, 2 module, complete all as specified and directed.

S&F Modular socket 6A/16A , 2/3 pin combined, 2 module, complete all as specified and directed.

S & F Modular Regulator step type 120 watt, 2 module complete all as specified and directed.

S&F Modular Bell push, 6A, 1 module, complete all as specified and directed.

S&F Modular blank plate, 1 module, complete all as specified and directed.

S&F Modular type white cover plate with 2 module, complete all as specified and directed.

S&F Modular type white cover plate with 3 module, complete all as specified and directed.

S&F Modular type white cover plate with 6 module, complete all as specified and directed.

S&F Modular metal flush box, 1/2 module, complete all as specified and directed.

S&F Modular metal flush box, 3 module, complete all as specified and directed.

S&F Modular metal flush box, 6module, complete all as specified and directed.

S&F MCB, SPN, DB, 8 ways, double door, Metal door, IP-43 IK 09 in 100A protection, isolated neutral bar, insulated busbar assembly complete including provision of blanking plates as required & fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S & F MCB single pole and neutral rated capacity 6 to 32 amp rating 240V, breaking capacity 10KA 'C' curve and curren

t indication for individual pole and designed based on advanced current limiting hammer trip mechanism ,complete all as specified and directed.

All as per item No 87 here-in-before but for one fan point/exhaust fan point contrilled by one switch on the same board complete all as specified and as directed.

S & F bracket for curtain rod in pair etc complete all as specified and as directed.

M&L for preparation of old painted surfaces of steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

S & F MCB single pole rated capacity 6 to 32 amp rating 240V, breaking capacity 10KA 'C' curve and current indication for individual pole and designed based on advanced current limiting hammer trip mechanism ,complete all as specified and directed.

Each Pair

Supply and fixing LED tube light batten type made of CRCA sheet with decorative end caps suitable with ultra bright glass LED tube light 1x18/20 watt T8 type single side connection complete with both end bi-pin holder and all accessories internally prewired and fixed to wall/celling incl fittings accessories and connecting up with twin core fexible copper conductor cable suitable size all as specified.

S & F energy saving new generation enviromental friendly long life versatile presure die cast aluminium IP 66 for securty ligh fitting luninaire with high power LEDs as ligh source (100 Im/watt) with LDR sensor for automatic ON/OFF operation and electronic driver of capacity 25 watts with pre-wared and necessary mounting arrangements and provison of 1.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade braket 1.5 mtr long bend to requred shape with clamps, nut botls including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer , complete all as directed by Engineer-in-charge.

S&F call bell ding dong, 230V single pole, complete all as specified and directed.

S & F Bed Spotlight made up of polycarbonate complete with LED 5 watt light including connection with all necessary accessories complete all as specified and directed.

Taking down ceiling fan/exhaust fan any sweep and depositing the same to MES store yard complete all as specified and directed

S & F for wall mounted LED tube light fitting 10 watts batten for surface mounted, anodized extruded aluminium housing , high transmissitivity diffuser , high lumen output box type fitting , 230 volts and intregated electronic driver connector block etc , complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193from ceiling rose to fitting complete all as specified and as directed.

Taking down geyser of any capacity, keeping with custody and refing the same complete all as specified and as directed.

S&F energy saving BLDC ceiling fan; 5 star rating, Type of motor - Brush Less DC Motor (BLDC) and Input Power - 32 to 35 Watts with full speed and reduced power consumption with reduced speed technology, Voltage- 90-300V AC, 50Hz, single phase, RPM - 340 to 375 rpm, Blades- Decorated, Sweep - 1200 mm, Air delivery - Not less than 210 CFM with service value 6.00 BEE and Colour - Glow white/ Toast Brown/ Gloss Black or others as approved by GE, complete all as specified and as directed.

S&F 2 module socket with shutter 25Amps, 240 volts including Modular Metal Flush box and cover plate, complete all as specified and directed.

Excavation in trenches not exceeding 1.50 m wide and 1.5 mtr depth for foundation etc, not exc 10 sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning filling in including spreading, leveling watering well ramming in layers not exc 25cm thick complete all as specified and directed.

Removing excavated materials (soils) not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and directed.

Taking down GI pipes 15 mm dia from trenches/walls/floor etc complete all as specified and directed.

Taking down GI pipes 20 mm dia from trenches/walls/floor etc complete all as specified and directed.

Taking down GI pipes 25 mm dia from trenches/walls/floor etc complete all as specified and directed.

Taking down GI pipes 40 mm dia from trenches/walls/floor etc complete all as specified and directed.

Taking down GI pipes 50 mm dia from trenches/walls/floor etc complete all as specified and directed.

S & F for energy Exhaust fan of 300 mm sweep made of metal body Ventil Air-DS type complete with louver with botls nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaut fan for connection and making suitable size of hole to existing brick wall for fan base complete all as specified and directed. (Note: Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted). complete all as directed and specified.

Taking down CI pipes 80 mm dia from trenches/walls/floor etc complete including all joints all as specified and directed.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing and as directed. Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life .

All as per ite

S & F Decorative wall light fixture, brushed nickel finish, suitable for 9 W LED lamp (B22) including 9/10 W LED Bulb etc, complete with all accessories internally pre-wired and including connecting up with twin core twisted fiexible copper conductor cable suitable size, complete all as specified and directed.

All as per item No 87 here-in-before but for one 5/15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLSH) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, complete all as specified and as directed.

m No 87 here-in-before but for one 3pin 5 Amp switch socket outlet,same board complete all as specified and as directed.

S&F PPR (Poly Propylene random co-polymer) pipe size 110 mm OD, PN-10 (SDR-11) IS-15801, 3-layer (outer green coloured UV stablized, middle black coloured UV stablizer and innermost layer white coloured with anti-microbial property) having thermal stability for hot & cold water supply with and including all necessary including all fitting such as elbow, tee, socket, bends, union joint etc complete all as specified and directed.

S&F PPR (Poly Propylene random co-polymer) pipe size 90 mm OD, PN-10 (SDR-11) IS-15801, 3-layer (outer green coloured UV stablized, middle black coloured UV stablizer and innermost layer white coloured with anti-microbial property) having thermal stability for hot & cold water supply with and including all necessary including all fitting such as elbow, tee, socket, bends, union joint etc complete all as specified and directed.

S&F PPR (Poly Propylene random co-polymer) pipe size 50 mm OD, PN-10 (SDR-11) IS-15801, 3-layer (outer green coloured UV stablized, middle black coloured UV stablizer and innermost layer white coloured with anti-microbial property) having thermal stability for hot & cold water supply with and including all necessary including all fitting such as elbow, tee, socket, bends, union joint etc complete all as specified and directed.

S&F PPR (Poly Propylene random co-polymer) pipe size 40 mm OD, PN-10 (SDR-11) IS-15801, 3-layer (outer green coloured UV stablized, middle black coloured UV stablizer and innermost layer white coloured with anti-microbial property) having thermal stability for hot & cold water supply with and including all necessary including all fitting such as elbow, tee, socket, bends, union joint etc complete all as specified and directed.

S&F PPR (Poly Propylene random co-polymer) pipe size 25mm OD, PN-10 (SDR-11) IS-15801, 3-layer (outer green coloured UV stablized, middle black coloured UV stablizer and innermost layer white coloured with anti-microbial property) having thermal stability for hot & cold water supply with and including all necessary including all fitting such as elbow, tee, socket, bends, union joint etc complete all as specified and directed.

All as per item no 133 above but 20 mm Bore.

Taking down PVC rain water pipes (any size or pattern ) including all fittings head shoes etc complete all as specified and as directed.

All as per item no 133 above but 50 mm Bore.

Taking down unserviceable CI sluice valve 80 mm to 150mm dia complete all as directed.

M&L for steel water tubing medium grade galvanised with new fitting laid in trenches 15mm bore :-

All as per item no 133 above but 40 mm Bore.

All as per item no 133 above but 25 mm Bore.

Supply, Jointing and laying in trenches in standard length , centrifugally cast ( spun ) ductile iron ( DI ) pressure pipes,with inside cement mortar lining and black bitumen external coating, nominal daimeter, class K-7 classification, confirming to IS-8329 ISI marked , including pushon and rubber gasket joints and jointing necessary DI specials etc including testing, complete for 100mm bore all as specified and as diercted.

Taking down CI pipes including all fittings of 100 mm bore including checking and segregation of servicable pipe and keep the sservicable pipes and lead in safe custody for cleaning and refixing complete all as specified and directed.

All as per item no 144 above but 150mm bore

All as per item no 147 above but 100 mm bore

M&L for construction of brick masonry valve pit of size 1200x1200x900mm (internal dimension) one brick thick wall in CM 1:4 on 100mm thick PCC 1:4:8 type D-2 (40mm graded aggregate) as in foundation, and 15mm thick rendering in cement mortor (1:4) internally, externally up to 15cm below GL, providing valve pit cover made of 3 mm thick MS sheet/plate, welded with 40 X 40 X 5mm angle iron frame fixed on top of valve pit by means of hold fast 150mm long, embeded in PCC 1:2:4 type B-1 (20mm graded aggregate) block of size 230 x 200 x 100mm and provision of hinges, handle and locking arrangement including two coats of anti-corrosive paint over a coat of red oxide zinc chrome primer and necessary excavation and earth work in soft/loose soil including dismantling of existing valve pit complete all as specified & directed.

M&L for construction of brick masonry valve pit of size 900x900x900mm (internal dimension) one brick thick wall in CM 1:4 on 100mm thick PCC 1:4:8 type D-2 (40mm graded aggregate) as in foundation, and 15mm thick rendering in cement mortor (1:4) internally, externally up to 15cm below GL, providing valve pit cover made of 3 mm thick MS sheet/plate, welded with 40 X 40 X 5mm angle iron frame fixed on top of valve pit by means of hold fast 150mm long, embeded in PCC 1:2:4 type B-1 (20mm graded aggregate) block of size 230 x 200 x 100mm and provision of hinges, handle and locking arrangement including two coats of anti-corrosive paint over a coat of red oxide zinc chrome primer and necessary excavation and earth work in soft/loose soil including dismantling of existing valve pit complete all as specified & directed.

S&F in repair Cast Iron Air release valves conforming to IS 14845-2000 with tamper proof arrangement of size 80 mm bore incl taking down of old unsv one complete all as specified and directed.

S&F CI/DI bends (any type, radius and angel) tapers any type (straingh, bend, increasing, decreasing or double socket etc) tee pieces single brancehs 'Y' junction double branch, cross (all socket or socket and spigot) collars, caps and plugs up to 150mm dia fcomplete all as specified & directed.

Cutting out existing CI/DI pipe line upto 150/200mm dia, inserting tee reducer including necessary lead joint Complete all as specfied and directed.