PDG. ELECTRIC SUBSTATION AT SUB DIVISIONAL CIVIL HOSPITAL ELLENABAD IN DISTT. SIRSA.

Amount

MCCB ,DISTRIBUTION BOARDS, MCB's, RCCB's, CHANGE OVER etc. (HSR 23.22) Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. (HSR 23.22.1) TRIPLE POLE MCCB 16 to 100 Amp, 25 KA (HSR 23.22.1.3)

TRIPLE POLE MCCB 125 to 160 Amp, 25 KA (HSR 23.22.1.4)

4 pole MCCB 300 to 400 amp (HSR 23.22.1.12)

SITC Four pole ON LOAD Manual change over switch in SS enclosure of following Ratings (HSR 23.22.8) 400 amp 415 volts (HSR 23.22.8.5)

SAFETY ITEMS (HSR 23.26) Supply and erection of Medium Voltage caution notice plate of size 200*150 mm in three languages.(HSR 23.26.1)

Supply and erection of High Tension Voltage caution notice plate of size 250*200 mm in three languages. (HSR 23.26.2)

Supply and erection of shock restoration chart in glass frame. (HSR 23.26.3)

Supply & Erection of mild steel bucket stand suitable for 6 Nos. fire buckets,(but without bucket) including the cost of welding and painting of complete stand will one coat of red oxide and 2 coats of approved paint of red colour with all labour and material required to complete the job in all respect up to the entire Satisfaction engineer in charge of the work (size 6'x4' made of GI pipe 32mm dia). (HSR 23.26.4)

Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current. The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1 :2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineerin-charge of the work:-(HSR 23.27) M.S. pedestal of size 600 mm wide , 750 mm high ,300 mm deep and bottom totally open , duly embeded in 1 :2:4 cement concrete block of size 750 mm x 450 mm x 200 mm above ground level , having a base of size 900 mm x 600 mm x 250 mm below ground level. (HSR 23.27.1)

EARTHING AND LIGHTENING ARRESTOR (HSR 24.1) Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. (HSR 24.1.1)

Extra for using salt and char coal/coke for pipe earth electrode as required. (HSR 24.1.2)

Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. (HSR 24.1.3)

Earthing with tinned copper earth plate 6D0mmx600mmx3mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) etc. complete as required. (HSR 24.1.4)

Extra for charcoal or coke and salt for G. I. plate or copper plate earth electrode. (HSR 24.1.5)

Supplying and laying 25mm x 3 mm G.I. strip in 40 mm dia,GI pipe as/from earth electrode including soldering etc. as required. (HSR 24.1.7)

Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material. (HSR 24.1.8)

Providing and fixing 25 mm x5 mm copper strip in 40 mm dia G.I. pipe from earth electrode as required. (HSR 24.1.9)

Providing and fixing 25 mm x 5mm copper strip on surface or in recess for connections etc. as required with all labour and material. (HSR 24.1.10)

Supply and erection of 20mm x 3 mm thick GI, tape fixed with suitable G.I. staples of same size. (HSR 24.1.14)

LT CABLE (HSr 24.2) Supply and erection of suitable compression type brass cable glands for underground Cable (HSR 24.2.7) 70 sqmm to 95 sqmm Cable 3 to 3½ Core (HSR 24.2.7.4)

120 sqmm to 185 sqmm Cable 3 to 3½ Core (HSR 24.2.7.5)

Supply and erection of cable route marker made of 50 cm long 10 mm dia M.S. Rod welded/riveted at the top with 10 cm dia 3 mm thick MS plate inscribed with 'cable' word on it, having a cross arm 30 cm long of the same dia welded at the bottom, in exiting trench 45 cm below ground level. (HSR 24.2.10)

HT CABLE (HSR 24.3) Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required (HSR 24.3.3) 70 to 120 sqmm (HSr 24.3.3.1)

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required. (HSR 24.3.4) 70 to 120 sqmm (HSR 24.3.4.1)

MISCELLANEOUS ITEMS (HSR 24.5) S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Mtr below ground level including diging and refilling of earth including cost of suitable size socket/cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work.(HSR 24.5.2) DWC/HDPE pipe 90/75 mm outer dia/inner dia (HSR 24.5.2.4)

Transformer:- Supply, and erection, testing and commissioning of outdoor transformer of 250 KVA 11/0.433 KV 3 Phase 50 cycle copper wound Outdoor type up to the entire satisfaction of the engineer of the work as per detail specification given as under with required plate form & fancing etc. As per Latest BIS-1180-Level-2. Make. Voltamp/ Kirloskar/ ABB/ Siemens/ Alstom/ NGEF. NO load voltage ratio 11/0.433 KV No. of Phases = 3 Type = Double wound core type copper wound, Cooling = ONAN Duty = Outdoor Vector Group/ISS-DYN-11/IS: 1180- Level -2. Tapping on HV compensation + 5% to - 10% in steps of 2.5%. Tape changer - Off circuit Temperature rise (oil/res. 0c to 40/45 C) Altitude up to 1000M above M.S.L. Frequency Cycle 50 Hz. Fitting / accessories provides = Off circuit tape changer Externally hand operated Oil conservator with filling hole & cap. Plain oil level gauge with minimum level marking. Thermometer pocket. 4 Nos. plain roller Uni-directional Silica-Gel-Breather Ist filling of oil Drain-cum-filter valve Rating & Diagram plate Two earthing terminals Lifting arrangement Exploson vent Air release plug Oil temperature indicator with alarm & trip indicator. Winding Temperature indicator with alarm & trip contact. TERMINATIONS : HV=3 pole single glands cable box suitable for reception of 1 No. 3 core up to to 120sqmm XPLE cable copper lugs/thimble. L.V. = 4 pole 3 glands cable boxes suitable for 3 Nos. 400 sqmm. 3.5 core PVC cable having extended copper bars of requisite capacity duly tinned from L.T. bushing for making connection with cable including cost of copper lugs and thimbles. L.V. Neutral suitable box for earthing provided

POWER FACTOR PANEL 80 KVAR: Supply erection, testing & commissioning of cubical type panel dust & vermin proof. L.T. automatic power factor control panel 80 KVAR capacity suitable for automatic operation & control of power factor within the set limits free standing floor mounting made out of 14 guage mild steel with channel iron base frame painted with stove synthetic light grey enamelled paint suitable for operation on 3 phase 4 wire 50 cycle per second 400/440 volts A.C. supply equipped with the following as per diagram attached: 1 No. automatic power factor control relay of EE Co./ L&T make. Power factor meter size 96 x 96mm of AE make. Space for incomer 200 amp. triple pole moulded case circuit breaker. A set of pilot lamps (3 Nos.) phase indicating lamp of L&T make. Iron clad bus bar chamber suitable for 200 amp. 440 volts having 4 No. copper bars of cross section 25 mm x 5mm duly tinned and insulated with PVC sleeves. Connection from incomer moulded case circuit breaker to bus bar by means of solid copper strip of requisite capacity duly tinned & insulated with PVC sleeving. 2 Nos. 3 phase 20KVAR dry capacitor of MPP type iemens / L &T make (total 20 KVAR) 1 Nos. 3 phase 10 KVAR dry capacitor of MPP type Siemens/ L&T make (totaled 20 KVAR) 2 Nos. 3 phase 32 amp. contactor for 10 KVAR capacitor of L&T /Siemen make 3 Nos. 3 phase 63 amp. contactor for 20 KVAR capacitor of L&T /Siemen make 3 Nos. 32 amp. HRC fuse with holder of L&T /GE make. 3 Nos. indication Lamps 220 volts for ON indicator of respective capacitor of L&T make. 3 Nos. push button ON/OFF manual operation of L&T make Earthing copper bus bar of cross section 20 mm x 3 mm duly tinned and insulated throughout the lenght of panel. The panel will be complete with all internal wiring with PVC copper wire, inter connection etc. with all labour and material require to complete the job in all respect without cost of MCCB upto the entire satisfaction of the Engineer-in-charge of the work

Supply Erection testing & Commissioning of 11 KV HT metering panel complete with C.Ts P. Ts. Cubical and electronic meter with accuracy class as per requirement/approved by DHBVN at the time of installation, consisting of the following. (As per Approved by DHBVPNL). Cubical panel free standing floor mounting type made out of sheet steel 14 SWG CRCA sheet with channel iron base frame spray painted with strong synthetic light grey enamel paint as per size and design approved by the DHBVNL 3 Nos. 11 KV CTS of rating as approved by DHBVNL for indoor installation of appd. Make of 1 Nos. 11 KV PTs 11000/110 Volts Oil filled suitable for indoor installation of approved make DHBVNL. Space for Digital Electronic Meter 3 phase 4 wires recording in KWH and rating and accuracy as by DHBVNL with push button display operating system of different kind of readings. The cubical panel will be completed in all respect including intter connection, internal wiring with PVC copper cable, its testing and approval of all item by DHBVNL including cost of all testing/ approval charges of all items of DHBVNL with a guarantee of one year from the date of commissioning including cost of all labour and material required to complete the job but excluding the cost electronic meter in all respect up to the entire satisfaction of the engineer in charge of the work.

S/E of fire bucket 9 Ltrs Capacity of G.I. sheet of 24 gauge write with " FIRE" as per fire specification.

Supply and erection of stay wire suitable for 9/11 M. long RCC pole make out of 7/8 SWG GI wire with U type MS rod 5/8" dia duly threaded by means of angle iron of size 50 mm x 6 mm x 30 cm and 6 ft. long MS rod 5/8" dia 5' buried in the ground after fixing with cross channel size 75 mm x 40 mm x 60 cm. The stay wire will be binded on the top of the pole with help of suitable size of double U type MS clamps and stay fixed with nuts& bolts. The stay wire shall be insulated in the middle point with the help of egg. Insulator and complete with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work.

Supply and erection of 11 KV pin insulator with pin make with all labour and material required to complete the job including fixing the same on existing channels up to the entire satisfaction of Engineer-in- Charge of the work.

Supply and erection of 11 KV gang operated switch make conforming to IS with latest amendment including suitable size of copper blade erection of same on the existing 'H' pole with the help of 3 No. channels of size 75 mm x 40 mm x 6 mm, 1.8 M long fixed with suitable size of MS clamp, nuts and bolts including cost of 6 No. 11 KV insulator with GI pin R.D. fuses and painting with 2 coat of approved paint and one cost of red oxide and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of work.

Supply and erection of lightening arrester module suitable for 11 KV G.O. switch with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-Charge of the work.

Supply and erection of fencing of transfer for safety precaution made out with the help to 50 cm x 50 cm x 6 mm angle iron, M.S. plate 50 mm x 6 mm, M.S. Jaal the perportionate quantities required in 1 sqm duly painted with red enameled paint including one coat of red oxide. The fencing angle shall be embedded in ground with C.C. mixture at least 60 cm in ground level including all labour and material required to complete the job up to the entire satisfaction of Engineer-in-charge of the work.

S/E angle iron, channel & clump with nut & bolts of various sizes required for made the platform & G.O. switch etc.

Supply and erection of underground LT Power Ard. Cables of Aluminium Conductor complete with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work.95 Sq. mm 3.5 Core Ard. Cable. (For APFC Panel)

120 Sq. mm 3.5 Core Ard. Cable. (For Light Load)

185 Sq. mm 3.5 Core Ard. Cable . (For Main Load Bank)

Supply and erection of prestressed cement concrete pole as per IS : 1678-1960. 11 meters long 105 mm x 115 mm at top and 105 mm x 315 mm at bottom with working load of 200 Kg. buried 1.80 m in ground.

Supply and erection of Aluminium HT Cables, Stranded Compactedt Circular Aluminium Conductor, Conductor Screen with Extruded Semi Conducting Compound, XLPE Insulated, Insulation Screening with Extruded Semi Conducting Compound in Combination with Copper Tape, Cores Laid Up, Innersheath of PVC, Galvanised Steel Flat Strip Armoured, & Overall PVC Sheathed Cable Conforming to IS 7098 (Part-2) 2011 with upto Date Amendments complete in all respect upto the entire statisfaction of the Engineer- in charge of the work. i) 95 sqmm 3 core HT XLPE cable

Non Schedule Items Supply and erection of Rubber Mat 1mx2mx 12mm thick suitable for 11/33 KVA as per IS No. 15652C/M/L 3017739 as per approved by Chief Electrical inspector, Govt. of Haryana

Providing RCC foundation of M20 grade of the 250 KVA Transformer set complete in all respects and as per directions of Engineer-in-charge of the work.

Wrought iron and mild steel (using angles, flates, square bars, tee and chanels) ladders, grills, gratting frames, window guards, iorn doors, openable or fixed stair case or perrapet or any other type of railing, gates and tree guards etc. including cost of screws and welding rods or bolts and nuts complete fixed in position. Chanel size (40 x 40 x 6) = 10 M X 3.5 kg Per M = 245 Kg or 2.45 QTL.Wiremess Jalli = 100 kG = 1 QTL, Net & Bolts = 10 KG = 0.10 QTL, Total = 2.45 + 1 + 0.10 = 3.55 QTL

The Darba Kalan Shila Coop L/C Society Ltd.