EXTERNAL PERIODICAL SERVICE TO MD ACCN AT KHETRAPAL ENCLAVE, MAP-I AND KLP AREA UNITS UNDER AGE B/R-II AT SURATGARH MIL STN

Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

M&L for 15mm thick rendering in two layer on fair faces of brick masonry or concrete surfaces of walls consisting of 1st layer of 10mm thick plaster in CM 1:6 and 2nd layer (setting coat or top layer) of 5 mm thick plaster in CM 1:4 mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished fair & even, complete, all as specified. Note:- (i) Rates of water proofing compound deemed to be included in quoted rates.

M&L for 10mm thick rendering in cement mortar (1:6) on fair faced surface of brick masonary or concrete surface of walls, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for 5mm thick rendering in cement mortar (1:3) on brick or concrete surface of ceiling, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for rough cast finish plaster with a mixture consisting of crushed stone or fine gravel aggregate mixed with coarse sand and cement in the ratio of 1:1:1 over & including 12mm thick rendering in cement mortar 1:3 on fair faces of brick masonry or concrete surfaces of walls complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surface of walls & applying two coats of cement base paint of approved shade/tint over a coat of cement base primer and filling cement based putty in cracks complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, filling cracks with wall care putty etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying two coat of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of new plastered and unplastered surfaces of wall and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company depot tinted) with silicon additives @ 1.43 litre / 10 sqm over and including one coat of primer applied @ 0.9 litre / 10sqm as per manufacturer instruction complete all as specified & directed by Engineer-in-Charge . Note: (i) Application of paint shall be strictly done as per manufacturers instructions including sealing of cracks with acrylic wall putty/any material specified by manufacturer and applying of exterior primer of approved make. (ii) Application should be carried out through manufacturer authorised applicator and with air less paint sprayer machine of approved make as mentioned in Appx 'A'.

M&L for complete removal of existing treatment from old plastered surfaces of wall, using mechanical means/grinding machine and washing of old surface with water of wall, preparation of surfaces including filling of cracks and two coats of 100% premium Acrylic emulsion paint by using roller having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company depot tinted) with silicon additives @ 1.43 litre / 10 sqm over and including one coat of primer applied @ 0.9 litre / 10 sqm as per manufacturer instruction complete all as specified & directed by Engineer-in-Charge. Note: (i) Application of paint shall be strictly done as per manufacturers instructions including sealing of cracks with acrylic wall putty/any material specified by manufacturer and applying a coat of exterior primer of approved make. (ii) Application should be carried out through manufacturer authorised applicator and with air less paint sprayer machine of approved make as mentioned in Appx 'A'.

M&L for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing,scrapping down smoke soot mulds, moss and efflorescent, salts, filling of cracks etc and applying a coat of cement based paint complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing,scrapping down smoke soot mulds, moss and efflorescent, salts etc and applying two coat of cement based paint complete all as specified & directed by Engineer-in-Charge.

M&L for rewriting/repainting of existing writing letters or figures not exc 30 cm height in block roman, italian or indian letters including stops, comma, arrows, brackets, dashes etc on sign board (Black or yellow base) including two coat of oil paint over a coat white base synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and directed by Engineer-in-charge.

S&F in replacement 110mm bore PVC (SWR) pipes single socketed in any length ring jointed with adhesive fixed to walls with neccesary PVC Clamp complete all as specified and as directed by Engineer-in-charge.

S&F 110 mm bore PVC (SWR) bends any radius jointed with adhesive complete all as specified and as directed by Engineer-in-charge.

S&F in repair stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm pvc pipe complete all as specified and directed by Engineer-in-Charge --------------------------------------------------------------------------- Note :- Old unserviceable material retrieved from above mentioned all items shall be deposited in store yard of subdivision by the contractor at his own arrangement. Noting extra shall be paid on this account.