ADDITION / ALTERATION AND SPECIAL REPAIRS TO BUILDING NO P-11 AT TRV UNDER GE HADDO

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons, risers of steps, skirting, dado etc., laid bedded and pointed in any mortar complete all as specified and as directed.

Demolition of cement concrete (un reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for vitrified tiles light shade 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white/ coloured cement, laid over and including cement screed bed 15mm thick in cement mortar 1:4, complete all as specified.

All as per item No 04 above but as in skirting / dados etc. including backing coat 10mm thick in cement mortar 1:3, complete all as specified.

M & L for providing 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in floors finishing the surface of concrete topping even and fair without using extra cement, complete all as specified and as directed

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors etc, laid over and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for glazed ceramic designed coloured tiles in vertical surfaces using size of tiles 300x450x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with colour of tile with and including 10mm thick backing coat in CM (1:3), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for 16 to 18mm thick granite slab (of approved shade), machine cut, as in floors, vertical surfaces, steps (treads/risers) and the like laid over cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, polishing and rounding (chamfering) the edges complete all as specified and directed.

S & F 4mm thick PVC tiles/ sheets, laminated plain coloured, marbled mosaic or mottled finish, laid with approved rubber based adhesive in floors including all necessary arrengament coplete all as specified by Engineer in Charge.

Dismantling ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets and grid complete all as specified.

M&L for seamless gypsum board false ceiling 12 mm thick including for any sunk or raised moulding with 25mm long self drilling/tapping screws having Philips head with joining compound and 48 mm wide fibre tape to provide seam less finish and including GI frame work of seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flange of 20mm and 30 mm, web of 27 mm, fixed to surrounding wall using nylon sleeves and screws at 450 mm c/c / intermediate channel 0.9 mm thick having two equal flanges of 15 mm suspended from soffit at approx 900 mm c/c with GI cleats and steel expansion fasteners with and including ceiling section (not exceeding 1.2 m length) of 0.55 mm thick having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting across the intermediate channel at 457 mm c/c including hangers 6 mm dia GI adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3 mm size, 60 mm long & expansion hold fasteners 12.5 mm dia, 40 mm long and finally applying two coats of oil bound distemper with roller finish over a coat of primer complete all as specified and as directed.

S&F PVC insulation panels (thickness of insulation pannel 10mm) with EPS stuck to 1mm plain PVC sheet suitable placed in false ceiling grid made of Anodised aluminium snap grid frame work for false ceiling and including 6mm thick GI hangers adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flats 40x3 mm size long and expansion hold fasteners 12.5mm dia 40mm long all as per specification and drawing and as directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters without taking off shutters from frame exe 1.5 Sqm and n.exc 4 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters without taking off shutters from frame n.exc 1.5 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 1.0 sqm but n.exc 2.0 sqm each complete all as specified and directed.

Taking down Aluminium Windows chowkhats or frames with shutters without taking off shutters from frame exe 1.5 Sqm and n.exc 4 Sqm each complete all as specified and directed.

Taking down Aluminium Windows and Ventilator chowkhats or frames with shutters without taking off shutters from frame n. exc 1.5 Sqm each complete all as specified and directed.

S&F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F flush shutters 35mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides including 6mm thick wooden lipping around the edges of shutter complete all as specified and as directed.

S&F 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), fixed to chowkats complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube as per specification & drawing, fixed in opening complete all as specified and as directed.

S & F for Factory made solid PVC molded with particle board core door shutter 28 to 30 mm thick panel design with 2mm thick molded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing all as specified

S & F Mild steel casement stays, size 300mm, with hinged joint and two plates, with studs complete all as specified and directed.

S&F Brass barrel tower bolt, with cast or sheet barrel and rolled or cast bolts 150mm long and fixed complete all as specified and as directed.

S&F Brass barrel tower bolt, with cast or sheet barrel and rolled or cast bolts 100mm long and fixed complete all as specified and as directed.

S&F Brass sliding door bolt 300mm long with sand or die cast brass hasp staples (bolt type) and fixing bolt with rolled or drawn brass bolts (dia of bolt not less than 16 mm) and fixed complete all as specified and directed.

S&F 100 mm butt hinges extruded brass, with mild steel hinge pin, bright polished, type B-1 complete all as specified and directed.

S&F 150 mm size brass handles, fabricated type polished complete all as specified and directed.

S&F 100 mm size brass handles, fabricated type polished complete all as specified and directed.

S & F floor door stopper of brass body and tongue with hard drawn steel spring overall length of cover plate150mm complete all as specified and directed.

M&L for HDF boards (fire & water proof) of 19mm thick as in CB, cabinet, shelves etc & the like with an including 02 coats of synthetic enamel spray painting glossy finish over a coat of primer incl preparation of surface complete all as specified and as directed.

M&L 18 mm thick rubco huat rubwood in built up interiors as in cupboards, shelves wall lining, box structure and including all fitting items complete all as specified and directed. After completing the carpentry works all the visible woods area will be sanding by No.60 & 80 Wood Sanding Paper, after that will be applying Sheenlac make Filler with mixing of NCD Thinner (Sheenlac make), then pasting Chock Putty in the shabby/nailing area which will be sanding with No.120 Sanding Paper, after that will applying Sealer of Sheenlac make and walnut colour stainer, then cutting with No. 320 Sand Paper, after completing the above process will spray Melamine Polish of Berger/Sheenlac make then cutting with No.400 Sanding Paper. Finally will applying Silicon make: Waxpol with soft Banyan Cloth for better shining/finishing. Make of rubber wood members: RUBCO or equivalent

M&L for polishing on old wooden (rubber wood) surfacees of any description width or girth including cleaning and sanding with sand paper complete all as specified and as directed

S&F auto hinges stainless steel grade AISI-316 (type Austenitic anticorrosive in nature) suitable for kitchen cabinets,CB , Shelves etc

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of pink primer complete all as specified and as directed.

M&L for powder coated anodised aluminium, window and door/ventilator with frame and shutters fully or partly glazed, sliding/openable/fixed fully glazed and panels fixed with panels inserts 12 mm thick pre-laminated particle board/sheet glass including necessary jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodized aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts etc. The size of aluminium section shall be all as specified in relevant IS Code and SSR Part-I complete all as specified and as directed. NOTES: (i) Supply only floor spring, glass, Imax hinges, SS friction hinges, particle board, aluminium fly proof mesh will be measured and paid separately under relevant items of this BOQ. (ii) Weight of aluminium section only shall be accounted for the purpose of payment. However unit rate quoted shall be deemed to include for cost of rubber beading, neoprene packing, fittings such as handles, butt hinges, tower bolts, rollers for sliding windows, locking arrangement and fixing only of panel inserts of glass/ particle board/aluminium fly proof mesh etc. (iii) Weight of aluminium handle, butt hinges, tower bolts shall not be accounted for payment purpose.

Supply only plain sheet glass 4.0 mm thick ordinary quality and glazing with aluminum glazing clip in aluminum window shutter not exc 0.5 Sqm in each pane complete all as specified and directed.

Supply only figured glass, pin head type sheet glass 4.0 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window shutter not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F floor door stopper of aluminium alloy body & tongue, anodised with hard drawn spring of 140mm size fixed in floor complete all as specified and directed

Supply only Aluminium alloy wire mesh 0.45 mm nominal dia of wire average width of aperture 1.40 mm and fixed with aluminum wire staples all as specified and directed.

Supply and fix aluminium alloy wire mesh 0.45 mm nominal dia of wire average width of aperture 1.40 mm and fixed with aluminum wire staples all as specified and directed.

M&L for anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan- necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

S&F for 110mm dia PVC (SWR) single socketed pipes in any length complete with rubber ring joints fixed to wall etc using synthetic rubber adhesive cement solvent complete all as specified.

S&F for 110mm dia PVC (SWR) bends any radius complete all as specified.

S&F for 110mm dia PVC (SWR) bends with acess door any radius complete all as specified.

S&F for 110mm dia PVC (SWR) branch piece single (Single T ) equal or unequal complete all as specified.

S&F for 110mm dia PVC (SWR) vent cowl complete all as specified.

S&F for 75mm dia PVC (SWR) single socketed pipes in any length complete with rubber ring joints fixed to wall etc using synthetic rubber adhesive cement solvent complete all as specified.

S&F for 75 mm dia PVC (SWR) bends of any radius complete all as specified and directed.

S&F for 75 mm dia PVC (SWR) bends with acess door of any radius complete all as specified and directed.

S&F PVC (SWR) branch piece, single (SingleT ) of radius equal or unequal, 75mm dia complete all as specified and directed.

S&F PVC (SWR) branch piece, single (Single Y) of radius equal or unequal, 75mm dia complete all as specified and directed.

S&F PVC (SWR) vent cowl, 75mm dia complete all as specified and directed.

M&L PVC (SWR) multi floor trap 75mm with grating including jointing with solvent cement complete all as specified and directed.

Supply and fixed in repairs vitreous china WHB white Table top basin of size 420 x 420 x 135mm of square shape approved brand excluding taps waste chain complete all as specified. (Make- Jaquar Cat No. ARS-WHT-39901) or equivalent complete all as specified and directed.

Supply and fixed in repairs vitreous china wash down single piece WC of size 410x720x800mm with softclose seat cover with 'S' or 'P' trap and other connecting items approved brand including fix with white cement complete. (Make-Jaquar Cat Pt No. VGS-WHT-81751P and VGS-WHT-81201) or equivalent complete all as specified.

S&F in repairs pillar tap, Cast Copper alloy, 15mm dia, chromium plated, fancy type, screwed down, high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, fixed complete all as specified and as directed. MAKE: PRAYAG Cat part No. PIS-50H or equivalent in PARRYWARE/ZOLOTO/JOHNSON

S&F bib tap, long body with flange cast copper alloy, 15mm dia, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, fixed in repairs complete all as specified and as directed. MAKE: PRAYAG Cat part No. PIS-08H or equivalent in PARRYWARE/ZOLOTO/JOHNSON

S&F two way bib cock, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed both ends for iron pipe or for unions, fixed in repairs complete all as specified and as directed. MAKE: PRAYAG Cat part No. PIS-12H or equivalent in PARRYWARE/ZOLOTO/JOHNSON

S&F angular stop cock, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, with long shank and cup screwed down, screwed both ends for iron pipe or for unions, fixed in repairs complete all as specified and as directed. MAKE: PRAYAG Cat part No. PIS-10H or equivalent in PARRYWARE/ZOLOTO/JOHNSON

S&F in repairs towel rack, brass, chromium plated with lower hanger stainless steel with hook complete all as specified and as directed. MAKE: PRAYAG Cat part No. BA-12 or equivalent in PARRYWARE/ ZOLOTO/ JOHNSON

S&F towel ring, brass, chromium plated with round flange, fixed in repairs complete all as specified and as directed. MAKE: PRAYAG Cat part No. BA-11 or equivalent in PARRYWARE/ ZOLOTO/ JOHNSON

S&F toilet paper holder, brass, chromium plated, fixed in repairs complete all as specified and as directed. MAKE: PRAYAG Cat part No. BA-38 or equivalent in PARRYWARE/ ZOLOTO/ JOHNSON

S&F soap dish holder, brass, chromium plated, fixed in repairs complete all as specified and as directed. MAKE: PRAYAG Cat part No. BA-45 or equivalent in PARRYWARE/ZOLOTO/JOHNSON

S&F health faucet, brass, chromium plated with 8mm dia, 1.0 m long flexible tube, screwed for iron pipe or for brass ferrule 15mm dia or bore fixed in repairs complete all as specified and as directed. MAKE: PRAYAG Cat part No. BEA-41 or equivalent in PARRYWARE/ ZOLOTO/ JOHNSON

S&F wall mixer 3-in-1 system with provision of both hand shower and over head shower composite with 115mm long bend pipe connecting legs & wall flanges with and including hand shower with 8mm dia shower tube, 450mm long shower arm and over head shower, fixed in repairs complete all as specified and as directed. MAKE: PRAYAG Cat part No. PIS-80H for wall mixer PRAYAG Cat part No. BHS-87 for hand shower including 1.5mtr flexible tube with hook PRAYAG Cat part No. BOS-90 for shower arm & over head shower

Supply and fix in repairs PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and as directed.

S&F in repairs door closer hydraulically regulated, designation No.3 universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed aluminium (Die cast ) body. complete all as specified and as directed.

S&F in repairs 20 to 25mm dia Harrison rails (curtain rails), powder coated, anodised aluminium alloy with fancy type fixing curtain brackets, stops, rollers etc., complete all as specified and as directed.

S&F corner glass shelf with CP bracket guard fixed in repairs complete all as specified and as directed. MAKE: PRAYAG Cat part No. BEA-44 or equivalent in JAQUAR/PARRYWARE

Taking up or down 20mm dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 25mm dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

S&F 20mm bore unplasticised PVC pipes of pressure rating 10 Kgf/cm² including fittings, fixed complete to walls, ceilings or in floors etc., complete all as specified and as directed.

S&F 25mm bore unplasticised PVC pipes of pressure rating 10 Kgf/cm² including fittings, fixed complete to walls, ceilings or in floors etc., complete all as specified and as directed.

S&F in repairs 25mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron or CPVC pipe, fixed in repairs complete all as specified and as directed.

M&L for Cutting chases in PCC block walls, for concealed water tubing etc., and making good, cutting not exc 10cm girth complete all as specified and directed.

S&F 50mm bore low density polyethylene pipes (LDPE) of pressure rating 6 Kgf/cm2 fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness including similar pattern roof coverings complete all as specified and directed.

S&F for pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering fixed with self tapping screws complete all as specified and directed.

S&F for pre painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering, ridge, eves gutters etc fixed with self tapping screws complete all as specified and directed.

Dismantling of wrought iron or mild steel work and structural steel work of any description or otherwise provided for complete all specified and directed.

M&L for rolled section as in main and cross beam, hip and jack rafter,purline where connected to common rafters and running rails and guides for sliding doors fixed witg angle cleats or other connecting plates of grade Fe-410 (grde E-165) complete all as specified and as directed.

S&F in repairs for aluminium wind tie of any size fixed with self tapping screws of size 50/75mm with integral EPDM washer in roof covering and including dismantling of old wind tile complete all as specified and as directed.

M&L for preparation of new steel and iron surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for preparation of old steel surfaces over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint over one coat of red oxide primer all as directed.

Demolition of cement concrete of any description and in sunken floor /roof padding etc not otherwise specifically provided for.

Material and labour for providing PCC 1:2:4, type B0, using 12.5 mm graded stone aggregate as in sunken floor/ roof padding and similar work including water proofing compound all as specified and directed. Note :- WPC shall be measured and paid separately as supplied only.

M&L 10 mm thick Plaster on RCC roof slab with CM ( 1:4 ) including water proofing compound @ 3% by weight of cement shall be carried out as specified. (Note : WPC shall be measured and paid separately)

M&L for preparing plastered surfaces and applying primer @ 0.30/Kg per sqm and applying tack coat of bitumen 85/25 @ 1.2 kg/Sqm laying 3.0mm thick polyster reinforced APP modified water proofing membrane weighing not less than 3.5kg/sqm one coat of bitumen based paint @1.20 ltr/sqm over APP membrane including removal of existing water proofing treamant on roof, sunken slabs, edges and vertical surfaces complete all as specified

M&L for applying a coat of reflective bitumenous aluminium paint @ 0.15 Kg / sqm over Bitumen surface complete all as specified and as directed.

Supply only integral water proofing compound.

Demolition of Precast cement concrete block walling built in CM or Cement lime Mortar complete all as specified and as directed.

M&L precast cement concrete block masonry exc. 10 cm width with solid block C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:6) all as specified.

Providing precast cement concrete solid building blocks or slabs Type C1 1:3:6 (20 mm graded aggregate) 10cm thick (with plain or interlocking joints as directed) setting in mortar(1:4) complete, in walls complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in cooping complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc., and removal of debris to outside MD land complete all as specified and as directed.

M&L for rendering in two layer i.e.5mm thick in CM 1:4 including with or without mixing water proofing compound over 10mm thick in CM (1:6) on concrete/block masonry surfaces and finished even and smooth without using extra cement on all as specified.(Note WPC shall be measured and paid separately)

M&L for 10mm thick plaster in CM (1:6) on fair faces of concrete/PCC block surfaces of walls finished even and smooth (without using extra cement) all as specified.

M&L for preparation of newly plastered wall surfaces with 3mm average thick wall care putty and applying two coat of oil bound distemper over one coat of primer including leveling the surface which undulation found with cement putty etc complete all as specified and directed.

M&L for preparation on newly plastered external wall surface and applying two coats of weather proof (exterior grade) acrylic emulsion paint with anti fungal property over a coat of primer of the same manufacturer as that of paint complete all as specified and as directed. (Make: Dulux Weather Shield Max or Apex Ultima from Asian Paints or Berger weather coat All guard).

M&L for complete removal of existing treatment on wall by scrapping, washing, cleaning etc with 3mm average thick wall care putty and applying two coats of acrylic emulsion distemper over one coat primer including filling of cracks, holes and including leveling the surface which undulation found with wall care putty etc. all as specified.

M&L for complete removal of existing treatment of old decorated external wall surface by scrapping, washing, cleaning etc and applying two coat of weather proof (exterior grade) acrylic emulsion paint with anti fungal property over a coat of primer of the same manufacturer as that of paint incl filling cracks, holes using wall care putty complete all as specified and as directed. (Make: Dulux Weather Shield Max or Apex Ultima from Asian Paints or Berger weather coat All guard).

M&L for preparing old plastered surfaces of ceilings and complete removal of existing treatment by scrapping, washing, cleaning etc and applying two coats of oil bound distemper over one coat primer including filling of cracks, holes etc. with cement putty complete all as specified.

M&L for rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates etc Fe 410-W Grade E-250 Quality A complete all as specified and directed.

M&L for 6mm thick X 150mm wide non-asbestos decorative planks (shera planks) fixed to steel members with suitable screws/fasteners/nuts and bolts & washers and applying two coats syenthetic enamel paints complete all as specified and directed. Make:- Shera Planks or Equivalent

S & F stainless steel tubing of any diameter of circular, square or rectangular in shape of grade AISI-316 (type Austenitic anticorrosive in nature) as in railings / grills / designer work including post top cap, bottom plate, cutting, bending, seamless welding and fixing in any type of location incl taking down old railing of any description complete all as specified and as directed.

M&L PCC (1:4:8) type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified & directed by Engineer-in-Charge.

S&F for glossy finished heavy duty chequered cement concrete tiles 30cmx30cmx25mm thick set jointed with grey cement and pigment and pointed in neat cement slurry including 20 mm thick screed bed of CM(1:6) in floors complete all as specified and directed.

M&L for two coats synthetic enamel automotive paint applying with spray gun machine including prepration of existing surfaces of doors, windows etc., complete all as specified and directed.

Taking down copper/aluminium point wiring(light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Taking down fuse Unit/DBs with MCB/MCCB 415 Volt/230 Volt complete all as specified and directed.

Taking down light fittings of any type complete all as directed

Taking down old sub main wiring of any size complete all as specified and directed.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC casing and capping of suitable size (not less than 25mm) and accessories fixed on walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for ONE 6A light / fan / SOCKET OUTLET/Bell point controlled by one, one way 6 Amps modular switch.

ONE LIGHT/FAN point controlled by one, one way 6 Amps switch.

TWO LIGHT points controlled by one, one way 6 Amps switch.

ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps switch on independent board.

ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps switch on same board with other switches.

ONE BELL point controlled by one, one way 6 Amps switch.

M&L for Point wiring complete with 4 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC casing and capping of suitable size (not less than 25mm) and accessories fixed on walls/ceilings etc., including provision of PVC insulated 4 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for ONE 16A SOCKET OUTLET point controlled by one, one way 16 Amps modular switch on independent board.

S&F modular switch, one way, one module, single pole, 6 Amps complete all as specified and as directed. Make : Roma(Anchor) / Legrand / Seimens / Havells

S&F modular switch, one way, one module, single pole, 16 Amps complete all as specified and as directed. Make : Roma(Anchor) / Legrand / Seimens / Havells

S&F modular socket outlet, multipurpose, 2/3 pin, 6/16 Amps combined, 2 module, single pole, complete all as specified and as directed. Make : Roma(Anchor) / Legrand / Seimens / Havells

S&F modular socket outlet, multipurpose, 2/3 pin combined, 2 module, single pole, 6 Amps complete all as specified and as directed. Make : Roma(Anchor) / Legrand / Seimens / Havells

S&F modular bell push, one way, one module, single pole, 6 Amps, 240 Volts AC complete all as specified and as directed. Make : Roma(Anchor) / Legrand / Seimens / Havells

S&F AC starter switch of capacity 25 Amps working on 240 Volts, AC supply suitable for split type airconditioner complete all as specified and as directed. MAKE: CRAB TREE Cat part No. ACTO252504 or equivalent in ANCHOR/HAVELLS/L&T

S&F communication modules for Tele Socket RJ 11 2 Gang Tele Socket sap code No. ACAKRTW112. Make : Havells (Crabtree)/ Anchor / Bajaj

S&F communication modules for TV Socket sap code No. ACAKTOW000. Make : Havells (Crabtree)/ Anchor / Bajaj

M&L for ceiling rose, three terminal, 65x20mm size, PVC/Polycarbonate, insulated body, 6A, 240 volts complete all as specified and as directed.

S&F electric bell, single pole working , AC, 230 volts complete all as specified and as directed. Make : Roma (Anchor)/ Legrand/ Siemens/ Havells

Taking down carefully old unserviceable ceiling fan of 1200mm sweep deposit to MES Store yard under AGE E/M Haddo and S&F new ceiling fan of 1200mm sweep, 220V, 50Hz AC supply, metallic body 5 star rated including providing of twin core copper wire 23/0.0076 from ceiling fan to ceiling rose complete all as specified and as directed. Make : CG (Model No : Energion HS-5 Star or equivalent make of Havells/ Orient/ Usha

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified.Make:Roma (Anchor)/Legrand/Simens/Havells

Taking down carefully old unserviceable exhaust fan of 300mm sweep deposit to MES Store yard under AGE E/M Haddo and S&F new ceiling fan of 300mm sweep, metallic body with louvers including all fixing arrangement complete all as specified and as directed. Make : CG (Model No : Drift Air 12" / Orient/ Usha

S&F Exhaust fan 250 mm sweep, white in colour, 220Volts, AC Supply including all fixing arrangement complete all as specified and directed. Make: CG Model : Ventilus 10"/Havells /Orient/Usha

S&F of LED tube light fittings with 20 watts (Warm White/ White Colour as per requirement of site complete) light source in integral module with polycarbonate / Acrylic diffuser more than 85% efficiency of light with LED lamp efficacy as 110 Lum/W THD < 15% with operating voltage range 150-300V, 50Hz with driver efficiency > 85%, surge voltage withstand 2.5KV, Power factor > 0.9, energy efficient fitting surface mounted including connecting up with two/three core cable complete all as specified and directed. Make : Luker/ Havells/ Philips/ Crompton Note : Quoted rate is inclusive of any other misc materials required for fixing new fittings.

S&F LED light fitting of capacity 10 watts (Warm White/ White colour as per requirement of site complete) with aluminium extruded channel finished in anodised, Class I power factor >0.9 pre wired with electronic driver high translucent frosted PMMA diffuser for glare free smooth lighting distribution surface mounted complete all as specified and directed. Make : Luker/ Philips Cat Part No : Astra Line 2 Ft or equivalent make of Havells

Taking down carefully old unserviceable water heater of capacity 25 Ltrs and refixing the same with painting of two coat of synthetic enamel paint and any minor complaint rectified all as specified and directed by Engineer-in-Charge.

S&F Water Energy Efficient BEE 5 Star rated storage type of 25 Ltrs capacity, vertical electric complete including flexible pipe for hot an cold water, dead weight pressure release valve, Anchor fastner - 04 Nos of suitable size all as directed by Engineer-in-Charge. Make : Havells (Model No : GHWAMGSIB025) or equivalent make of CH/ Usha

S&F recessed mounted 15 watts, LED ceiling light fitting, yellow/White colour, round / square shape (Warm white/ warm colour as per requirment of site complete) made from die-cast aluminium and CRCA covering, powder coated in white colour suitable for armstrong/ grid ceiling complete with separate electronic driver complete all as specified and directed. MAKE: PHILIPS (Model No. Astra Max Metal Panel) / CROMPTON GREAVES (Cat Part CDR-205-15-57-SL-NWH) or equivalent make of HAVELLS/Luker Note : The rate quoted deemed to include for any alterations required to existing false ceiling as per site condition for fixing light fitting.

S&F decorative ultra slim linear LED light fixture of 18 Watts capacity, recess mounted, 230 Volts, 50 Hz AC supply, extruded aluminium heat sink, environmental friendly energy efficient light fitting, surface mounted round/Square in shape (Warm white/ white colour as per requirement of site complete) complete all as specified and as directed. MAKE: Crompton Cat part No. LSCRM-18W-CDL or equivalent in PHILIPS/ HAVELLS

S&F LED bed side lamp of capacity 3 watts with LED bulb (White/ Yellow colour of light as required at site) complete all as specified and directed. Make : Philips (Model No : 48042)/ C&S/ Havells/CG

Taking down old unserviceable street light mounting bracket od any size and S&F new bracket made up of 25mm dia galvanised steel tubing, medium grade, 1.20 metres long, bent to shape with inner angle not less than 120°, with and including necessary fixing clamps fabricated out of angle iron/flat iron of suitable size, bolts, nuts and washers as required and applying two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed.

S&F 25 watts LED Security light fittings IR 65 luminaire. Pressure die cast aluminium housing powder coated graphite grey and toughened glass of IP 65 including necessary fixing arrangements as per site requirements complete all as specified and directed. Make : C & S Model No. LTESSE25WLED/ Philips Model No. BRP020LEDHP/CW240V25/ CG Cat No - LSTS-25-CDL-M/ Havells/ Luker Cat Part No : LOHY210 WH

Taking down reflexing light fitting all as specified and direcetd

Suplly and laying of rigid non metallic PVC conduit of 25mm dia exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reduses, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles pipe hooks etc all as directed

M&L for Sub main wiring complete with two runs (1P+1N) of 6.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral) and one run of 6.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor as earth wire green in colour including lugs, drawn through and including 32mm wide rigid non-metallic PVC casing and capping and its accessories (OR) 25mm dia PVC conduit and conduit accessories fixed on surface of wall/ceiling/roof/ floor complete all as specified and as directed. NOTE: Two runs of 6.0 Sqm copper conductor, One run of 6.0 Sqmm copper conductor as earth wire and and one run of PVC casing and capping / PVC conduit shall be measured as one unit length.

M&L for Sub main wiring complete with two runs (1P+1N) of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral) and one run of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor as earth wire green in colour including lugs, drawn through and including 32mm wide rigid non-metallic PVC casing and capping and its accessories (OR) 25mm dia PVC conduit and conduit accessories fixed on surface of wall/ceiling/roof/ floor complete all as specified and as directed. NOTE: Two runs of 4.0 Sqm copper conductor, One run of 4.0 Sqmm copper conductor as earth wire and one run of PVC casing and capping / PVC conduit shall be measured as one unit length.

S&F MCCB DB sheet steel enclosure, VTPN, 4-way, double door, 415 Volts with 200 Amps rated bus bar, IP-43 protection suitable for incoming MCCB 160/200 Amps and outgoing MCB TP, cement spill protector concealed in wall and making good disturbed surfaces to match with surrounding surface complete all as specified and as directed. MAKE: L&T/ LEGRAND/ INDO ASIAN/ HAVELLS

S&F MCCB, 4 pole, 100 Amps, 50Hz, 25KA rupturing capacity, 415 Volts adjustable type with thermal and magnetic release complete all as specified and as directed. MAKE: L&T/ LEGRAND/ INDO ASIAN/ HAVELLS

S&F MCB DB, SPN, 8-way, vertical type, double door, 240 Volts with 200 Amps rated bus bar, IP-43 protection, shrouded neutral bus bar, cement spill protector, concealed in wall and making good disturbed surfaces to match with surrounding surface complete all as specified and as directed. MAKE: INDO ASIAN /L&T/ HAVELLS

S&F MCB, SPN, "C" series, 230 volts, 40 Amps, 10 KA rupturing capacity complete all as specified and as directed. MAKE: INDO ASIAN /L&T/ HAVELLS

S&F MCB, SP, "C" series, 240 volts, 6 to 32 Amps, 10 KA rupturing capacity complete all as specified and as directed. MAKE: INDO ASIAN /L&T/ HAVELLS

CHANDER SEKER ENTERPRISE

SKV Engineering

V KARTHICK

M/s Ramesh Lal

Sree Tirumala Enterprises

M/s K Moorthi

SHUBHAM SHANKAR GAIKWAD

LOOK UP ENTERPRISES