SPL REPAIR TO WATER PROOFING TREATMENT IN BLDG NO P-133 P-167 and P-181 ROOF TREATMENT IN BLDG NO P-222 AND PROVN OF ONE TOILET ADJUNCT TO BLDG NO. P-380 UNDER GE DRONACHAL BHOPAL

Amount

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out in Soft / disintegrated rock.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in Soft / disintegrated rock.

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. in Soft / disintegrated rock.

M&L for PCC 1:4:8 type D2 (40mm graded stone aggregate in foundation filling and mass concrete)

M&L for PCC 1:5:10 type E2 (40mm graded stone aggregate in foundation filling and mass concrete)

Formwork for Rough finished surfaces of concrete, to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter.

Formwork for Rough finished surfaces of concrete, to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelves including supports,overhangs,etc. also splays between floors and beams, etc.

Formwork for Rough finished surfaces of concrete, to sides of pillars,posts, struts, piers, columns and stanchions.

Formwork for Rough finished surfaces of concrete, to chullah hoods, chajjas,troughs and similar items including edges.

Formwork for Rough finished surfaces of concrete, to soffits and sides of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

All as per Item No12.00 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregates) in foundations, footing, plinth beams, bases for columns and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregates) in lintels over 1.5m clear span, beams and cantilevers complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregates) in slabs supported on walls, beams & columns complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregates) in columns, pillars, posts & struts complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregates) in chajjas complete all as specified and directed.

M&L for brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4

M&L for rendering 15mm thick in CM (1:6) mixed with water proofing coumpound @ 3% by the weight of cement on brick work or concrete surfaces finished even & fair complete all as specified & as directed.

M&L for rendering 15mm thick in CM (1:4) mixed with water proofing coumpound @ 3% by the weight of cement on brick work or concrete surfaces finished even & fair complete all as specified & as directed. Note:-Water proofing coumpound will be measured saperately.

M&L for rendering 10mm thick in CM (1:4) mixed with water proofing compound @ 3% by the weight of cement on concrete surfaces in ceiling finished even & fair complete all as specified & as directed. Note:- Water proofing compound will be measured separately.

Supply only Integral waterproofing compound.

M&L prepararing newly plastered surfaces of wall, pilasters, comices etc and applying two coat of water based exterior emulsion over and including a coat of primer over a coat of birla white putty as Approved by GE complete all as specified & as directed.

M&L for one coat of 1mm thick wall care putty on wali surface.

M&L for prepararing newly plastered surfaces and applying three coats of white wash on walls all as specified and directed

M&L for prepararing newly plastered surfaces and applying two coats of white wash on ceiling all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (Using 12.50mm graded stone aggregate) as in floor complete all as specified & as directed.

S&F ceramic (non skid) coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor, set & jointed in neat cement slurry & pointed in white or coloured cement to match over & including 15mm thick screed bed in CM (1 : 6) complete all as specified & as directed.

S&F glazed ceramic coloured tiles 350x 250x 7mm / 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in colour cement on vertical surfaces such as in dado/skirting etc over and including 15 mm thick rendering in cement mortar 1:4 complete all as specified and as directed

S&F vitreous china squatting pan “ORISSA” pattern size 580mm X 440mm, white with P or S trap front or back inlet with integral foot rest (excl flushing cistern & flush pipe) & including connection to trap & to flushing pipe anti syphonage pipe etc complete including making good to floor complete all as specified & as directed.

S & F 10 ltrs capacity PVC low level flushing cistern, ISI marked of make specified with inlet, float valve and handle including bracket with 32 mm dia PVC pipe 600 mm long complete all as specified and as directed.

S&F vitreous china counter top oval shape wash basin and waste pipe complete all as specified & as directed.

M&L for 18-20mm Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M&L for 10mm thick plastering in CM(1:4) on concrete roof surfaces using water proofing compound @ 3% by weight of cement and finishing the surface even and fair including taking down existing plaster and APP membrane all as specified and directed. Note :- WPC shall be measured and paid separately.

M&L for painting roof surfaces with one coat of bitumen primer T-10/polymerised grade conforming to IS-3384 @ 0.30kg /Sqm and one coat of bonding material using blown type bitumen confirming to IS-702 grade 85/25 @ 1.20 Kg/Sqm ,laying of 3mm thick APP membrane, weight not less than 3.50 Kg/Sqm with 10cm side overlap having centre core of 100 micron HMHDPE, outer film is 20 micron each and applying one coat of bonding material using blown type bitumen confirming to IS-702 of grade 85/25 @ 1.20 Kg/Sqm over APP membrane all as specified & directed.

M&L for precast machine pressed cement concrete tiles of size 250x250x20-22mm or 300x300x20-22mm with grey cemet and no pigment, set jointed and pointed in neat cement slurry in floors, and cut and polished laid over and including 15mm thick cement mortar screed in 1:4.

S&F 500 ltr capacity rotational moulded polythene water storage tanks (cylindrical vertical with closed top three layer) hoisted and fixed in position incl 20mm dia bore ball valve PTMT high pressure with polythene float and fly nut complete all as specified and directed.

S&F in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed all as specified and directed.

M&L for PCC 1:3:6 type C2, using 40mm graded stone aggrgates as in platform to PVC water tanks all as specified and directed.

Cutting chases not exceeding 10cm girth for concealed water tubing and making good in cement mortar 1:3 complete all as specified and as directed.

Supplying, fixing, jointing and testing galvanised iron tubing medium grade with all fitting such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete all as specified and as directed for the following sizes:-

15 mm dia bore

20 mm dia bore

S&F 15mm bore CP bib tap cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule complete all as specified & as directed.

S&F 15mm bore dia Chromium plated stop valve/angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed complete.

Supply only 15 mm bore chromium plated Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed as directed by Engineer-in-Charge.

S&F PVC connection 15mm dia of length not less than 450mm with both ends, brass fly nut complete all as specified & as directed.

S&F towel rail 600mm long of PTMT fixed with and incl CP brass screws and wooden/plastic cleats (min wt 190gms) complete all as specified.

S&F PVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified & as directed.

S&F 75mm dia PVC (SWR) pipe and single socketed in any length with rubberring joint laid in trenches or in floor.

S&F 75mm bore PVC (SWR) bend in any radius.

S&F 75mm bore PVC (SWR) junction (single ‘T’) equal or unequal.

S&F 110mm dia PVC (SWR) pipe and single socketed in any length with rubberring joint fixed to wall.

S&F 110mm dia PVC (SWR) pipe and single socketed in any length with rubberring joint , laid in trenches or in floors.

S&F 110mm bore PVC (SWR) junction (single ‘T’) equal or unequal.

S&F 110mm bore PVC (SWR) bend in any radius.

S&F 110mm bore PVC (SWR) vent cowl.

M&L for Hardcore of Broken stone or boulders of gauge n exc. 63 mm, deposit-ed, spread and lev-elled in layers n exc. 15 cm thick, watered and rammed to a true surface.

M&L for PCC 1:3:6 type C-2 as in plinth protection 75mm thick.

M&L PCC 1:2:4 type B1 using 20 mm graded stone aggregate in drains and surface channels and finishing complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in coping including slightly rounded or chamfered angles and including necessary form work.

M&L for Providing precast cement concrete Type B1 1:2:4 (20mm graded aggregate) as in landings, cover slabs (for man holes etc.)

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete.

S&F 3 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire sta-ples complete all as specified and as directed .

S&F Framed work such as grills,gratings, etc with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

M&L for preparing new steel surfaces and applying two coat synthetic enamel paint over including a coat of red oxide primer over 10 cm width or girth complete all as specified and as directed.

S & F Solid PVC door frame of size 50 mmx 47mm made out of 5 mm wood grain printed PVC sheet reiforced with MS square tube and fixing in opening as per manufacturer instruction complete all as specified, directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded wood grain printed PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR-2004 Part - II, specified and as directed by Engineer-in-Chartge

S&F 200mm long aluminium anodised, barrel tower bolts of extruded section.

S&F 300mm long Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed as directed by Engineer-in-Charge.

Supply and fixing 100mm size butt hinges extruted aluminium alloy with galvanized mild steel hing pin anodised and fixed type C-21.

S & F 150 mm size extruded aluminium alloy handles cast type anodised and fixed.

Demoliton of cement concrete of any description including existing roof treatment, in any position not otherwise specifically provided for,complete all as specified and as directed.

M&L for cement concrete 1:2:4 mix type B-0 (12.5 mm graded stone aggregate) in padding finishing surface of concrete topping even and fair (without using extra cement) all as specified of average thickness 40mm in slope as required over roof complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in roof kerbs on roof chamfered on edge including troweling slightly complete all as specified and as directed.

M&L for Sand stone slabs in cover stones, set and pointed in cement mortar 1:4. complete.

Taking down of cement plaster inculding wall finishes in any description on brick or stone wall etc., incl hacking out joints for key scrubbing down with water etc. all as specified and directed

M&L for preparing plastered or unplastered new wall surfaces and applying two coats of cement base paint over and including a coat of cement putty.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position after cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes rtc of following capcity.

Exc 250 but n exc 500 Ltrs

Exc 500 but n exc 1000 Ltrs

Taking up or down steel tubing and connection including cleaning for refixing or removal to store yard of bore 20 mm all as specified and directed..

Taking up or down steel tubing and connection including cleaning for refixing or removal to store yard of bore 25 mm all as specified and directed..

Refixing old steel tubing and connections in new or old position as in walls ceiling floors etc bore of pipe 20 mm all as specified and directed..

Refixing old steel tubing and connections in new or old position as in walls ceiling floors etc bore of pipe 25 mm all as specified and directed.

S&F 25 mm dia galvanized steel tubing, medium grade, with all fitting and fixed complete to walls celling or laid in floors all as specified and directed.

S&F in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed all as specified and directed.

Fixing only in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed all as specified and directed.

S&F in repair 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed all as specified and directed.

Fixing only in repair 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed all as specified and directed.

S&F 110mm bore PVC (SWR) bend in any radius.

S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof.

Taking down existing unserviceable treatment of any description including cement plaster, any thickness from roof surfaces, cleaning of roof surfaces and preparing it for further treatment and removing rubbish from the site up to 50 mtrs complete all as specified and directed

M&L for brushing neat cement slurry with 3.0 kg of cement per square metre complete all as specified and directed.

M&L for crack filling with approved crack filling compound including necessary opening of cracks cleaning watering etc including necessary scafolding etc complete up to height of 8mtr from ground level complete all as specified and directed. Make :M/S pidlite or equivalent as approved by the GE

M&L for two coats of aluminium paint including preparation of new surface complete all as specified and directed by Engineer-in-Charge.

M&L for 10 mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6

M&L for preparation on newly plastered / previously untreated surfaces on walls and applying two coats of cement base paint over a coat or alkali resistan primer all as specified and as directed.

Demolition of cement concrete(Unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level).

M&L for 75mm thick PCC 1;3;6 type C-2 (40mm graded stone aggt) in plinth protection laid to slope of 1 in 12 and finishing cement concrete suraface even and smooth without using extea cement with and including all necessary form work to divide the area in panel, finishing exposed edges fair or rounding or chamfered of exposed edges and providing 6mm thick joints therough the thickness of plinth protection duly filled mastic filling of one part of hot bitumen 85/25 grade and three part of fine sand complete all as specified and directed by EIC.

M&L for complete removal of existing treatement of Ceiling and applying three coat of white wash all as specified and as directed.

M&L for complete removal of existing treatement of wall and applying three coat of white wash all as specified and as directed.

Preparing of old painted surfaces of any description and in any position over 10 cm in width or girth (not otherwise specifically described) and applying one coat of synthetic enamel paint (on wooden surfaces). All as specified and as directed.

All as per item Ser No 103.00 above but on steel surface (other than roof).

M&L for complete removal of existing treatement on walls and applying two coats of cement base paint over a coat or alkali resistan primer all as specified and as directed.

Disconnecting ,dismantling Solar Hot Water System' (Flat Plate Collector) based on indirect transfer of heat of capacity 100 LPD kept aside the all parts carefully for reinstalling the same all as specified and directed.

Disconnecting/dismantling of Rotational moulded polyethylene water storage tanks of capacity 500 Ltrs (cylindrical vertical with closed top) hoisted and fixed in position kept in safe storage for refixing all as specified and directed.

Fixing only Solar water Heater of capacity 100 LPD with flat solar plate collector type with heat exchanger and electrical back up complete.

Fixing only Rotational moulded polyethylene water storage tanks of capacity 500 Ltrs (cylindrical vertical with closed top) hoisted and fixed in position including connecing the exising water input and out going connections.

Dismantling rod assembly of capacity 1000/1500 watt fitted in solar water storage tank including draining of stored water, repairing the water leakage with suitable size of washers/gaskets replacing the rusted nut bolts with new one refixing and testing the functionablity the same after repair all as specified and directed by Engr in charge.

M&L for painting of GI strutures of storage tank mounted and solar plate fitted by scratching out old bubbled paint, sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint including with two coat of lime wash on structure coping all as directed by Engr-in-charge.

S & F of 3 core x 2.5 Sqmm FRLS insulated, PVC sheathed copper conductor cable for service connections solar heater element assembly.

M&L for Cross-Arms, Bracings, Supports, Clamps and Back Plates fabricated from Structural Steel Sections including Nuts, Bolts, Washer, welding, bending cold or hot, drilling holes for Bolts, in any shape or size as indicated or directed and inclusive of One Coat of Aluminium over finished surfaces complete all as specified and as directed.

Supply and fixing in replacement of float valve brass, high pressure with polythene float and fly nut complete screwed for iron pipe of 25mm dia bore .

S&F, Hot water pipe duly insulated with glass wool and aluminium cladding 20 mm dia bore fixed complete to wall, ceiling or laid in floors complete all as specified and directed.

S&F water Tubes 25 mm medium grade galvanised with all fitting laid in trenches all as specified and directed.

M&L for Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with mild steel/pressed steel sunken boxes( with earth dolly) duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:-

One light point controlled by one switch.

One exhaust Fan point controlled by one switch.

One 3 pin socket outlet 5 Amps on independent board.

One 3 pin socket outlet on same board.

Supply and fix of modular switch single pole one way 6 Amps, ISI marked complete all as specified and directed by Engr-in-charge.

Supply and fix of modular Socket single pole one way 6 Amps, 2 module ISI marked complete all as specified and directed by Engr-in-charge.

Supply and fix MCB SP, 240 Volt, 6 to 32 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed.

S&F Exhaust Fan 300 mm sweep with louver complete metal body complete all as specified and directed by Engr-in-Charge.

Cutting holes suitable for fixing 300 mm sweep Exhaust fans through brickwalls built in cement mortar and making good around the holes in cement mortar 1:3 complete all as specified and directed.

S&F LED Building security light fitting 1x 35 W new generation energy saving and environmental friendly long life made up of pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening seprate driver compartment with IP65 protection and impact resistance of IK07 for mounting existing bracket complete including all accessories pre-wired with 3 X 1.5 sqmm single core mutistrand copper conductor cable up to celing rose/ terminal box, all as specified.

S & F sheet metal enclosure for MCB DB, SPN 230 Volts 200 amps rated busbar 8 way double door complete all as specified and directed by Engr-in-charge.

S&F 6 Sqmm 2 core copper cable complete as direcetd.

Supply and lay for tubes 'medium grade ' with all galvanised fittings laid in trenches/on ground complete of dia 20 mm.

Cutting existing steel tubing for alteration and addition upto 100 mm dia existing pipe including necessary fitting ie clamp, elbow, ferrul complete all as specified and directed by Engineer-in-Charge.

S & F 1 x 18 watt LED tube light fitting basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver, LED Decorative luminaire with suitable for lamps LED Light high efficiency LED driver,Optimized heat dissipation for ensuring high LED life span.

CREATIVE CONSTRUCTION

Jyoti enterprises

AJIT ENTERPRISES

Nakoda Constrcution Company

Vee kay construction

SATHI ENTERPRISES