Provn of 02 x JCOs and 05 x OR Single living Accn (Including Electric work and Furniture Supply) at Signal Centre Mil Stn Gaya

Amount

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth, for foundation etc and getting out in soft/loose soil.

Excavation in trenches, n exc 1.5m wide and exc 1.5m in depth but n. exc 3m, for foundation etc and getting out in soft/loose soil.

Surface exvcavation n exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil

M&L for sand filling under floors or in foundations including watering and consolidation.

M&L PCC 1:4:8 type-D2 (40mm graded aggregate) as in foundations, filling and mass concrete.sub base as in floors.

M&L Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius built in CM 1:6 .

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 in half brick thick wall.

M&L 40mm thick damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4, type B-0.

Returning Filling in,including spreading, levelling, watering and well ramming in layers, not exc 25 cm in soft/loose soil..

Removing excavated material n exc 50 m and depositing where directed at level n exc 1.5m above the starting point.

M&L for hard core of gauge n.exc 63 mm deposited, spread and levelled in layers n.exc 15 cm thick with broken bricks, watered and rammed to a true surface complete all as specified.

M&L reinforced cement concrete (M-25 Design mix) (using 20 mm graded stone aggregate) in foundation, footing, foundation beams, plinth beams, bases for columns, pedestal, under reamed piles, mass concrete, etc complete.

M&L reinforced cement concrete (M-25 Design mix) (using 20mm graded stone aggregate) as in columns, pillars, posts, struts etc complete.

M&L reinforced cement concrete (M-25 Design mix) (using 20mm graded stone aggregate) as in slabs supported on walls, beams and column in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete.

M&L reinforced cement concrete (M-25 Design mix) (using 20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintel over 1.5m span etc complete.

M&L reinforced cement concrete (M-25 Design mix) (using 20mm graded stone aggregate) as in chajjas etc complete.

M&L Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for flat rough finished surfaces of concrete.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete.

M&L form work to sides of pillars, posts, struts, piers, columns and stanchions for rough finished , square, rectangular or polygonal surfaces of concrete

Form work to edges of concrete flats, treads, breaks in floors window cills, concrete railing, openings in concrete walls, floor and roofs n exc 20 cm wide and side of RCC/PCC bands in walls, horizontal or sloping and similar work complete all as specified.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as spd and as directed.

S&F MS TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hoopinbg for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips all as specified

Ditto all as per item No above but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders

M&L 15 mm thick rendering in two layers (10mm & 5mm ) on fair faces of bk / concrete surfaces in cm (1:4) with WPC (WPC measured & paid separetely) finished even and smooth (Without using extra cement ) complete all as spd and as directed.

Supply only water proofing compound (liquid), ISI marked.

M&L 15 mm thick rendering on fair faces of bk /concrete surfaces in cm (1:6), finished even and smooth (Without using extra cement ) complete

M&L rendering 10mm thick in CM 1:3 on concrete surfacves/ chajja/ ceiling, etc finished even and smooth without using extra cement

Preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white wash.

M&L for Prepration of new plastered surfaces of ceiling and applying three coats of white wash.

M&L Prepration of new plastered surfaces of wall and applying three coats of white wash

M & L for preparation of newly plastered surfaces of wall & concrete and applying 3mm thick wall care putty including preparation complete.

M&L for applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including, rubbing with sand paper complete on newly plastered surface.

Preparing surfaces of new wood and wood based materials of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of pink primer.

M&L for prepration of new steel surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer

M&L for 75mm thick PCC 1:3:6 type C2 using 20mm graded stone aggregate as in floor/plinth protection laid in suitable panels finished even and fair all as spd . 6mm Joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 gde and three part of sand ( all by weight) complete.

M & L for 20 - 25 mm thick machine cut Kota stone slab as in flooring over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including incl Screed bed or bedding layer of Cement Mortar (1:6), 15 mm thick for laying floor finishes, necessary grinding, rubbing, rounding to exposed edges and polishing in granite finish complete all as specified and directed. Note: (size of the stone slab not less than 23"x23")

M&L Machine cut Kota stone slab flooring 20-25mm thick as in skirting, over cement mortar laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete incl 10mm thick plaster in CM 1:4

M&L 75mm thick Cement concrete Type C2, 1:3:6 , 75mm thick (40 mm graded aggregate) as in sub base floor finished evevn & fair all as spcified.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.18 sqm & not exceeding 0.38 sqm in floors etc set & jointed in neat cement slurry and pointed with white or coloured cement to match complete.

M&L for screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6 for laying of floor tiles as directed.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.18 sqm & not exceeding 0.38 sqm in floors etc set & jointed in neat cement slurry and pointed with white or coloured cement to match in verticle surfaces complete.

M&L for glazed ceramics coloured tiles of size 450x350x7mm thick in vertical surfaces such as skirting/dados/wall, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces.

M&L for 10 mm thick plaster in cement mortar 1 : 4 for fixing of wall tiles complete all as specified.

S & F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube supplying & fixing in opening as per specified & drawing.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed all as spd.

S&F 150 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified.

S&F aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 250mm long.

S&F 35mm thick 2nd class hardwood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces , size of rail and stile as per IS:1003 (Part-I), Klin seasoned and chemically pressure treated all as per SSR complete all as directed.

S&F in repair 2nd class hard wood 35 mm thick glazed and gauzed skelton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and shutters as specified in SSR Part I, Section 8, clause 8.24 (a)

S&F for band ,strap, supports or stays for rainwater harvesting hooks(stay), heavy for large gates ,hinges,hasps staple,clamps ,hold fasts, hooks,plain angle cleatstwo way or three way straps, plate washers and similar small article confoming to Fe -290 Gde-E-165

M&L PCC 1:2:4 type B1 ( using 20mm graded aggregate) as in lintels upto 1.5m clear span , cills steps , seismic and other similar bands , plinth courses, string courses parapet ,railing ,coping,bed plates, kerbsbed blocks for hold fasts including necessary from work, PCC benching, copings etc.

S&F Pressed steel frames (Factory made) made out of 1.25 mm thick black MS sheet for doors, with one or more rebates including necessary fixing lugs, Butt hinges, lock strike plate, etc complete, size of frame 105x60mm mm incl bottom of each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either side and back fill to chowkats with PCC 1:3:6 type C-O using 12.5 mm graded crushed stone aggregate complete all as specified.

S&F Pressed steel frames (Factory made) made out of 1.25 mm thick black MS sheet for doors, with one or more rebates including necessary fixing lugs, Butt hinges, lock strike plate, etc complete, size of frame 125x60mm mm incl bottom of each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either side and back fill to chowkats with PCC 1:3:6 type C-O using 12.5 mm graded crushed stone aggregate complete all as specified.

S&F steel windows with side hung shutter incl box type butt hinges with bow handle,steel peg stay, tower bolts ( each shutter having two tower bolts 100mm long ) complete with glazing bars dovetailed or welded completev all as spd and as directed

-Ditto- all as per above item but without glazing bars

S&F steel ventilators with top hung shutters including hinges, steel peg stay complete.

S&F Mild steel framed works such as grills,gratings,etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work for portions framed and hung as gates, including pintle hinges, stops, hand made sliding bolts, etc conforming to Fe 290 Gde -E-165.

S&F 3mm thick sheet glass, frosted quality glazing with oil putty in square n exc 0.50 sqm in each pane of 3mm thick.

S&F Galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks etc complete all as spd.

Supplyband laying of 20mm CPVC pipes SDR11& plain CPVC SDR 11 fittings on walls / ceilings or laying in floors including unions ,brass elbow, brass tee, MBTA, FBTA complete all as specified.

Supply and laying of 25mm CPVC pipes SDR11& plain CPVC SDR 11 fittings on walls / ceilings or laying in floors including unions ,brass elbow, brass tee, MBTA, FBTA complete all as specified.

S&F Rotational moulded polyethylene water storage tanks in white colour tripple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I of 500 Ltr capacity all as spd.

S&F Ball valves 20mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete.

S&F in repairs Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both ends for iron pipe complete.

S&F in repair vitreous china WHB size 550x400 mm white flat back including pvc waste pipe but excluding taps, waste, chain & plug & porcelain stopper but including brackets with two coats of synthetic enamel painting over a coat of red oxide primer etc complete.

S&F white vitreous china wash down water closet pan pedestal pattern (white) including trap connection to drain or outgoing pipe, anti- syphonage pipe, etc complete all as specified and as directed.

S&F vitreous china squating pan 'Orissa' pattern WC size 580x440 mm white with integral foot rest and trap and including trap ,connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor all as spd.

S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete.

S&F mild steel chromium plated health foucet for 15mm dia pipe with 1.25m long flexible tube and ABC wall hook inclu making connection and fixed in position for EWC including nut/washer complete.

S&F PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and as directed.

S&F bib tap 15 mm bore, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F 15 mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly-nuts screwed for iron pipe & fixed complete.

S&F CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete.

S&F angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe.

S&F CP two way angle valve/ tap with wall flanges 15 mm bore, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F of stainless steel soap dish, of standard size and shape complete.

S&F chromium plated overhead shower rose swivel type 125 mm with CP arms 300 mm long complete all as specified and directed

S&F plastic water closet seat cover, Cream / white colour, closed pattern with flat bottom and cover and mild steel chromium plated aluminium hinging device for pedestral pattern WC.

S&F PVC (SWR) 'P' trap for 110mm dia etc complete.

S&F in repair chromium plated toilet paper holder with flap complete.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete.

S&F clamp made out of 50x5 mm flat iron, 16mm dia round iron stays including bolts & nuts and securing ends of stays to wall or roof for 110mm PVC pipe complete.

S&F PVC (SWR) bends/tie any radius provided with access door of 110 mm dia

S&F PVC (SWR) vent cowl 110mm bore

S&F PVC (SWR) nahani/ floor trap, plain with grating with or without waste hole including jointing with solvent cement 75mm dia etc complete

M&L Water proofing treatment on "Non approachable / non accessible and approachable roof" surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment, properly cleaning & drying the concrete surfaces complete

(i) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm

(ii) Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm incl cleaning surfaces.

(iii) Laying unrolled over the bitumen coated surface, polymeric water proofing membrane Hyperplas standard wt not less than 3kg /Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instruction.

(iv) Applying two coats of bituminous aluminium paint including preparation complete

M&L for PCC type B-0, 1:2:4 (Using 12.50 mm graded stone aggregate) in roof kerbs slab etc complete all as spd and directed,

M&L 5 mm thick rendering on roof surfaces/concrete surface in CM 1:4 complete.

M&L for Providing precast cement concrete 1:2:4, type B1 (20 mm graded aggregate) set in CM 1:6, as in cover slabs (for manholes etc) with plain fair faces, all as spd.pd.

M&L for DWC HDPE pipes class SN-8 laid in trenches of 150mm internal dia of pipe and jointed completed as specified and directed .

M & L for Hardcore of gauge exc. 63 mm but not exc. 100 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken bricks complete all as specified and directed.

M&L 55 mm thick PCC 1:2:4 type B-1 (using 20 mm graded aggregate ) as in floor, finishing cement concrete surface complete all as spd and direced

Forming 150mm deep x12mm thick expansion joints filled with pre-formed bituminous filler and 30mm primed and sealed with sealing compound Grade B complete.

M&L for Machine Pressed precast glazed colour reflective PCC interlocking paver block 60mm thick mixed with grey cement and pigment, laid dry and bedded on sand cushion complete all as specified and as directed by Engr-in-Charge. Note: Payment of sand cushion shall be measured and paid separately.

M&L PCC 1:2:4, type B1 (20mm graded Aggregate) as in surface channel and drain all as specified

M & L for extra for forming fair finished drain or channel 30cm inner girth using extra cement incl forms moulds mitered /stopped ends etc.

M & L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLS multi stranded conductor cable in and including concealed PVC conduit of size 20/25mm ISI marked inclusive of tees, bend, elbows etc upto and including sunk in anodized pressed steel box for housing switch socket etc with white laminated 3 mm thick hylum sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLS cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps.

(c) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board.

Description all as per item No 1 here in before but using 2.5 Sq mm single core copper conductor cable of multistranded FRLS PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 Sq mm copper conductor FRLS PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S & F switch piano type single pole 5 amp, 230 Volts complete all as specified and directed.

S & F switch piano type single pole 15 amp, 230 Volts complete all as specified and directed.

S & F socket outlet 2-in-1, 5 pin, 5 amp, 230 Volts complete all as specified and directed.

S & F socket outlet 2-in-1, 5 pin, 5/15 amp, 230 Volts complete all as specified and directed.

S & F ceiling rose, surface bakelite with 3 terminals, ISI marked for batten fitting complete all as specified

S & F stepped type electronic fan regulator flush type complete all as specified and directed.

S & F lamp holder, PVC / Polycarbonate type with back plate suitable for batten/ slanting fittings complete.

S & F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F Highly efficient LED Bulbs, 10 W, used as a ready replacement for existing GLS/CFL direct fit lamp, in B-22 cap complete all as specified and directed

S & F wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

S & F LED 10 watts batten aluminium extruded with decorative end caps complete and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including provision of 1.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting and necessary 40mm dia GI pipe light grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed.

S&F of electric water heater 25 Ltr capacity, steel body with copper inner tank and heating element upto 2 KW capacity, 230 Volts, BEE 5 star rated with all accessories such as safety valve, thermostate, NRV, SS connection pipe etc, fixing on wall through proper nut, bolt, and fastner including electric and water connection complete all as specified and directed.

S & F for energy efficient exhaust fan steel body AC single phase 230 Volts of 300 mm sweep complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed.

M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note:- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

Supply & laying in trenches /laid in floor/duct/drawn through conduit XLPE insulated, armoured, heavy duty elecric cable with alluminium conductor, 1100 volt grade cross sectional area 10 Sqmm 4 core.

M & L for laying of HDPE double wall corrugated pipes in trench for UG cable protection conforming to IS-14930 Part-II with IP-67 having outer dia 50 mm and inner dia of 38 mm including necessary fittings such as couplers, bends etc complete all as specified and directed. Make: Rex/ Rudrax Polymers/Finolex

Supply and laying for brick of common burnt clay, sub class 'B' old size laid flat and dry on cables as in cable protection in trenches over cables perpendicular to direction of cales abutting each other complete all as specified and directed.

Supply and laying pipe galvanized steel water tubing, "medium grade", ISI marked including fittings such as bends, elbows, tees, short pieces, connectors, backnuts, diminishing pieces, caps, plugs and unions, etc fixing complete with clips, wall hooks, wooden plugs or laying in trenches, etc complete for following sizes complete all as specified and directed. Note: The rates also include cutting through walls, floors, etc. and their making good.

(a) 20 mm dia

(b) 25 mm dia

Supply & fixing gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed for following size of pipes compete all as specified and directed :-

(a) 20mm bore pipe

(b) 25mm bore pipe

Almirah Med Steel DRG NO FD-1032(a)Almirah shall be with 3 shelves making four compartments. Shelves will have double bent flanges on all the four sides (b) Plain black MS Sheet 1 mm thick shall be used throughout. (c) Front shutter leaves shall be three butt hinges of 75 mm fixed to each shutter and shall be side hung. Six lever brass Lock shall be of Harrison/Link/Godrej Make. (d) Almirah shall be provided with CP steel handle 120mm long with three way locking system. (e) All joints and welding and fixing shall be done in accordance with standard workman ship. The surfaces shall be cleaned & prepared prior to apply of powder coating. (f) All internal/external exposed steel surfaces shall be given two coats of synthetic enamel paint (Olive green/Smoke grey or as approved by GE) over a coat of red oxide primer (Spray painting). (g) The colour shade of outer steel body should be in dual shade. (Shades shall be approved by GE/Engr-in-Charge) (h) Rest all as specified and shown on drawing or as approved by GE.

BATH MAT PVC DRG NO FD/E6/MAP/07 The Bath Mat PVC shall be made up of 5mm thick PPCP material .The size of the bath mat shall be 400mm Lx300mm Wx250mmH.The bath mat shall have centre leg of dia 25mm.The four legs shall be in arc shape and of size 10mmx100mm.The top of the bath mat shall have 3mmx10mm thick stiffener moulded along with the seat in single piece underneath. The weight of the bath mat shall not be less than 1.3 kgs. Make-Neelkamal/AMKO/Cellow/supreme.

CHAIR EASY DRG NO FD-229 (a) All timber shall be well seasoned 1st class hard wood Teak free from all defects with moisture content as per IS-287-1993. (b) White plastic cane shall be 2mm wide half round best quality except for borders, which shall be 4mm wide. (c) Weaving shall be of godrej pattern. (d) Provide PVC ring as specified where hard rubber ring shown on drawing. (e) All wooden surfaces exposed shall be french polished with two coats for glossy finish and remaining wooden surfaces shall be treated with linseed oil. (f) Rest all as per drawing.

CHAIR WRITING DRG NO FD/E6/MAP/12(a) FRAME: Frame shall be made out of 25mm x 10mm section MS tubular frame cantilever type powder coated. (b) HAND RESTS : One piece arm rest made of black integral skin polyurethane with 75-85 shore ‘A’ hardness and reinforced with MS insert. It shall be scratch & weather resistant. Both hand-rest sections shall have slope towards front. (c) FOAM: Polyurethane foam shall be 50mm thick and shall be moulded with density 50-55 Kg per cubic metre and hardness 20 ± 2 Kg on hampden machine. Back foam shall be designed with contoured lumber support for extra comfort and 12mm hot pressed plywood upholstered with fabric and moulded polyurethane foam with PVS lipping all around. (d) FABRIC : Fabric shall be contained the following material in various colours Arcylic, Polyester, Poly Propylene and shall be as approved by GE. (e) STOPPER: Four numbers of rubber stoppers shall be provided at bottom of the chair. (f) REST : All other items / fittings shall be as shown on drawing and provided as per relevant IS and trade engineering norms / pattern.

BED HARD DRG NO FD/E6/MAP/08(R)Overall size shall be 2050mm long, 900mm wide and 400mm high. All Steel shall be MS Square pipe of 18 Gauge. The head board shall be 800mm high and Foot board shall be 500mm high. The frame of head board and foot board shall be of 38mmx38mm MS square pipe.18mmx18mm MS square pipe shall be provided in the inner of head board frame/foot board frame as shown in drg.18mm thick both side decorative prelaminated particle board of approved shade with PVC edging shall be screwed to MS strip arc welded to 18mm thick rectangular pipe with standard workmanship both in head board/foot board..25mmx65mm rectangular CR pipe shall be used to make the long rails and short rails of bed hard and heavy duty nuts/bolts arrangement shall be provided for fixing long rails to the legs .One stiffener of size 25mmx25mm shall be welded between the two legs of headboard over 150mm from the ground level. The top of bed hard shall be of 12mm thick BWR ply of approved make fixed over the four equidistant stiffener of size 25mmx25mm SQ MS pipe in line with bottom of 25x65mm long rail section. PVC shoes shall be provided to legs of bed.All metal /iron work shall be treated with synthetic enamel black paint after doing a coat of red oxide primer.Rest all as per drg.

TABLE DRESSING GENTS WITH MIRROR DRG NO FD-230 (a) All timber (Except ply wood ) including edging shall be well seasoned 1st class hard wood free from from all defects with moisture contents permisible as IS-287-1993. (b) Top, left, right sides and front of box shall be 12mm thick three layer flat recessed teak wood particle board teak faced with PVC beading, except back of box which shall be of 12 mm thick plywood commercial BWR grade. (c) Sides and back of drawers shall be 12 mm thick teak wood and front of drawer shall be of 12mm thick three layer flat recessed teak wood particle board teak faced with PVC edging. (d) Mirror shall be 5.5mm thick electroplated polished glass of best quality as approved by Engr-in-Charge/ GE. (e) All expose surface of wood and board sufaces shall be finished with two coat of french polish except the back portion which shall be treated with linseed oil (e) Rest all as per drawiing.

TABLE 90X60CM WITH DRAWER DRG NO FD-283 (a) TIMBER : All wood work shall be of first class hard wood (Teak). (b) TOP : Top of table shall be of 18mm thick MDF bord with PVC edging all around. (c) DRAWER : 6mm thick ply commercial face both side shall be provided at bottom of drawer and all as shown on drawings and directed by E-I-C. (d) POLISH : All wood work and teak veneered surfaces shall be french polished. (e) RING : Hard rubber rings shall be screwed to the legs. (f) REST : All as per drawings.

TEAPOY DRG NO FE-278 (a) TIMBER : All wood work shall be of first class hard wood (Teak). (b) TOP : Top of table shall be of 18mm thick MDF bord with PVC edging all around. (c) DRAWER : 6mm thick ply commercial face both side shall be provided at bottom of drawer and all as shown on drawings and directed by E-I-C. (d) POLISH : All wood work and teak veneered surfaces shall be french polished. (e) RING : Hard rubber rings shall be screwed to the legs. (f) REST : All as per drawings.

CHARPOY IP HARD DRG NO FD/MAP-III/01 Overall size shall be 1980mm long, 900mm wide and 440mm high. Two long rails and two short rails shall be of 25mmx65mmx16 gauge MS rectangular pipe .The legs shall be of size 32mmx32mmx16 gauge welded to long and short rails as shown on drg.Two stiffeners of size 25mmx25mmx16 gauge shall be provided in equidistant between two opposite long rails. Six number cleat of size 25mmx60mmx6mm shall be welded with frame to support ply. Two stiffeners joining legs of size 25mmx25mmx16 gauge shall be provided at 150mm from ground level .12mm thick commercial plywood shall be provided for top as shown on drg with proper nut and bolt .one nut and bolt shall also be provided at centre of each stiffeners for fixing the plywood irrespective of what is shown on drg..PVC hard rubber shoes shall be fixed at bottom of each leg. All steel surfaces shall be painted with synthetic enamel black in color before applying a coat of red oxide primer. Rest all as per drg

LOCKER BED SIDE STEEL DRG NO FD-1029 (a) Overall size shall be as shown on drawing. (b) Locker shall be made from 1.00 mm nominal thick MS plain black sheet leg shall be made 1.20 mm nomial thick plain black mild steel sheet. (c) All joints /welding/fixing shall be done in accordance with standard workmanship and to the entire satisfaction of Garrision Engineer. (d) Locker shall be provided with 02 CP Steel handle 100mm long and 01 hasp and staple 75mm long to the main door. Hanging rod shall be 19mm dia MS tube of 2mm thickness chromium plated with suitable brackets. (e) All internal/external exposed steel surfaces shall be given two coats of synthetic enamel paint (Olive green/Smoke grey or as approved by GE) over a coat of red oxide primer (Spray painting). (f) The colour shade of outer steel body should be in dual shade. (Shades shall be approved by GE/Engr-in-Charge) (g) Rest all as per drawing.

M/S CHAUHAN CONSTRUCTION (BID ID -3080169)

M/S AJAY KUMAR SINGH (BID ID -3081262)

M/S VIKAS CONSTRUCTION CO. (BID ID -3082192)