Carrying out Additional Works in Approved Swimming Pools within Owala Majiwada Constituency under T.M.C limits

Amount

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.)

Excavation for foundation in Hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3.0m.

Excavation for foundation in Hard murum and boulders including removing the excavated material upto a distance of 50 metres, beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 m to 3.0 m.) By Mechanical Means

Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth/murum, ramming ,watering including shoring and strutting etc. complete. (Lift from 1.5m To 3.0 m.) By Mechanical Means

Providing earth work in embankment with approved materials obtained from departmental land or other sources upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing to the required lines, curves, grades and section, watering and compaction with Power roller to achieve not less than 97 % of standard proctor density etc. complete

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 3.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary)

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for steps including steel centering, plywood/steel formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.),with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, plywood/steel formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand Bd.E.4 Page No. 289 and B-7, Page No.38

Providing and laying Cast in situ/Ready Mix cement concrete M25 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete M25 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including centering, formwork, cover blocks compacting and roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Filling in plinth and floors with approved excavated material in 6M. layers including watering and compacting etc. complete.

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete.

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete.

Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Transportation of excavated earth including loading and unloading per truck trip of 6.00 cubic meter capacity per trip.

Providing and laying Cast in situ/Ready Mix cement concrete M25 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, compaction, finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mixcement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete M25 of trap / granite / quartzite / gneiss metal for R.C.C. canopy as per detailed designs and drawings including centering, formwork, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing etc. complete (excluding reinforcement). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and fixing in position after hoisting, precast 1:2 cement mortar reinforced jali 80 mm thick with 3 mm diameter mild steel bar reinforcement, of approved design on both sides, fixing in cement mortar 1:3 and curing etc .complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap / granite /gneiss / quartzite metal for R.C.C. fins of required thickness in position as shown on the drawings or as directed by Engineer-in-charge including steel centering, plywood / steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement, including cover block) Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing uncoursed rubble masonry of trap / granite / quartzite/ gneiss stone in cement mortar 1:3 in basement with patent water proofing compound added to it at rate of 1 kg per bag of cement including bailing out water manually, scaffolding racking out joints when plastering is to be done and watering etc. complete.

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of 2 bars of 6 mm diameter / 2 hoop iron strips 25 mm X 1.6 mm placed at every third course, properly bent and bonded at ends scaffolding, racking out joints and watering etc. complete.

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete.

WATER PROOFING OF SWIMMING POOL -- Providing and applying impermeable, monolithic application, UV resistant, Self curing, non toxic, high compressive strength, non shrink, polymer based Cementitious waterproofing mortar named as Poly Ironite Ceramic Cementitious (PICC) which consists of Nicomix Series + 53 Grade Cement + Water of Dimple Chemicals & Services Pvt. Ltd. for resurfacing the concrete surfaces of swimming pool to a thickness upto 10 mm or as per surface condition and also treatment of lift joints and honey combing areas, potholes etc. by removing loose material, dust particles, grout slurry by breaking it with manual / mechanical means. Removing of existing embedded M.S. bar if any, Cleaning the lift joints, honey combing areas and entire surface with special chemical named as Steripure 10 of Dimple Chemicals & Services Pvt. Ltd. for removal of algae - fungi followed with high pressure water jet. Apply bond coat named as Kelox R 101 + Kelox H 404 which is water miscible epoxy of Dimple Chemicals & Services Pvt. Ltd. before PICC application for suitable bond between old surface to new PICC mortar and then do the PICC application providing with Top coat of NicCoat PC + Kelmer A 60 of Dimple Chemicals & Services Pvt. Ltd.

Providing waterproof plaster in W.C. and bath 20 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 kg. per bag of cement of approved make and manufacturer and curing (and filling joints of Nahani trap and any outlet by properly) etc. complete.

Providing internal cement plaster 6 mm thick in a single coat in cement mortar 1:3 without neeru finish to concrete surface in all positions including scaffolding and curing etc. complete.

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:3 without neeru finish to concrete or brick surfaces, in all position including scaffolding and curing etc. complete.

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Providing and applying gypsum plaster ( with Gypsum material of Gypsum India / Mega Sign or equivalent make ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete.

Providing and laying Vitrified MATT finish having decorative type of size 1000 millimeter x 1000 millimeter of 8 to 10 millimeter thickness (on a existing flooring) with bonding chemical and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for flooring in required position laid on a bed of bonding chemical filling joints curing and cleaning etc .complete.

Providing and laying ceramic tiles having size 30 cm. x 45 cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.

Providing and laying 18 mm thick ADONI BROWN LEATHER FINISH stone for flooring, machine cut in required size, approved shade, color and texture laid using white cement slurry over 20 mm (average) thick base of cement mortar 1:4 followed by laying, fixing and jointed with white cement slurry mixed with matching pigment, including rubbing and curing moulding and polishing to edge to give high gloss finish etc complete. The application rate for tile adhesives shall be as per manufacturer's recommendations. as per detail drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels and as directed by Engineer in charge. Complete. a) Flooring

Providing and fixing Indian teak wood framed collar beam / king post / queen post truss, with all Iron work including scaffolding, if necessary, and one coat of primer etc. complete.

Providing and fixing Country cut teak wood double or single leaf panelled shutters, 35 mm thick style top and freze rail 95 x 35 thick with lock and bottam rail 195 x 25 mm thick and panels without ventilator as per detailed drawing excluding the door frame, stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats complete

Supply andDoor Closure: (For 2 Hr fire Rated EN-3 Door Closure) Supplying, fitting & fixing Surface mounted overhead Door Closer for 2 hour fire rated doors of different size (e.g size - EN-3 for leaf width upto 900mm) CE certified, marked & conforming to EN - 1154 of approved quality (Internationally reputed brand like Dorma, Geze, Hafele, Assabloy & Magnum etc.) fitted and fixed Complete as per direction & satisfaction of Engineer -in Charge including all taxes & incidental charges.

Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight 0.547 kg/Rmt. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 kg/Rmt. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. and top section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising without box

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete.

Providing and fixing mild steel grill work for windows, ventilators etc. 20 kg/sqm as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

Providing and applying two coats of synthetic enamel paint of approved colour to new /old structural steel work and wood work in buildings, including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.

Providing structural steel work of rectangular hollow steel section for steel trusses, other similar trussed items like purlin and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted/bolted/ welded connections and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade complete. Spec. No. : As directed by Engineer-in-charge. (TATA Steel)

Providing and fixing chicken mesh of 22 gauge, with about 30 cm. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /B.B.masonry and or tying by binding wire etc. complete.

Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres

Providing and fixing during laying in RCC Slab rectangular 2 mm thick M.S. sheet fan hook box of size 180x100 mm with required depth with holes or notches as required, bottom and top sides of 1.6 mm M.S. sheet fixed with 3.5 mm dia. round headed screws together with 12 mm dia. M.S. bar bent to shape with hooked ends for fan hook and painting to exposed surface

Providing and laying weep holes of 100 mm diameter PVC pipes as per drawing for abutment returns, return walls etc. Complete.

Prividing and fixing pressure relief pipes of 110 mm diametre of PVC as per drawing for R.C.C Raft, galaries returns, abutments, wing wall etc complete.

Hydraulic Excavator ( Tata Hitachi EX 350 )

Providing and casting in situ or precast tapering R.C.C. M- 20 Barrier type Kerb without gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In- charge. Using Concrete Batching and Mixing Plant

Providing and erecting Y type barbed wire fencing with seven rows of wire with 2.45 mm dia G.I. pipe ( Rezan/ concentiDeleted ire 0.75 mm dia ) with hot dip and G.I. coated hooks as per drawing supported on M.S. angle 50 x 50 x 6 mm at 2.5 mtr. c/c including fixing and fastening with wire, painting M.S. angles with one coat of red lead primer and two coat of oil paint etc. complete. As directed by Engineer in charge.

Providing and erecting chain link fencing 1.6 M. height with G.I. chain link of size 50 x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x 25 x 5 mm size and vertical M.S. flat 35 x 5 mm and 25 x 5 mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete. As directed by Engineer in charge.

RWH - Recharge Pit Providing and constructing recharge pit of 2.0m deep and 1.0m dia of pre-cast RCC rings with 6.5" dia x 25m deep borewell at the floor of recharge pit including installation of combination of solid/perforated PVC casing pipe wrapped around with netlon mesh including 300mm thick sidefilling around outside of RCC rings (annular space) with 40mm size boulders including filling of recharge pit up to 0.5m depth with 25-75mm clean washed gravels from bottom up followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m of washed river fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) including netlon mesh between each gravel/fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) media layer including covering with RCC slab, manhole frame & cover, PVC rungs, PVC end-caps, fittings etc. including arrangement for inlet & outlet pipe excavation & backfilling as shown in the drawing.The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge.

Construction of 100 mm dia. Bore well with drilling in all types of soil & rock upto 60 m incl. all materials,accessories,machineries .Fixing 7.5 HP capacity or as directed submersible pump ,including lowering PVC pipe,fixing electric switch etc.complete

Providing and fixing 1st class white glazed earthenware Orissa Type W.C. Pan 580 mm dia including P or S trap cast iron soil and vent pipe upto the outside face of the wall (1:5:1 0) cement concrete bedding 15 mm thick, 10 liter P.V.C. flushing cistern with all necessary pipe connection etc. complete. Spec. No.:As directed by Engineer-In-Charge.

Providing and fixing white european type wall-hung pan, of size 350mm x 355mm x 570 mm concealed flush tank with floor-mounting frame installing kit and drain pipe connection set for wall hung WC, with approved make square control plates including soil pipe, vent pipe upto the outside face of wall, 100mm dia C.I. plug bend inlet pipe all fittings,cutting & making good walls, floors etc. complete. Spec. No.:As directed by Engineer-In-Charge.

Providing and fixing white glazed urinal of size 710x460x300mm with sensotronic concealed type flushing valve for urinal with complete kit having fittings, inlet pipe with stop tap, brackets for fixing the cistern, 32mm diameter P.V.C. flush pipe with fitting and flushing arrangement including lead soil pipe, lead trap & soil pipe connection upto the outside face of wall etc complete.

Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140 kg with frame etc complete.

Providing and laying for ----mm dia. salt glazed S.W. Pipe including fitting such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete. Bd.V.39, Page No. 573 a) 150 mm.

Providing and fixing on walls/ ceiling/ floor mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. 25mm- up to Plinth

20mm- Plinth to First

15mm- Plinth to First

Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. 150mm- Up to Plinth

Providing and fixing P.V.C. Rain water pipes of 160mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. (The contractor shall give 3 yrs guarantee bond for payment)

Providing and fixing screw down 15 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete

Providing and fixing Oval Type Under Counter Wash Hand Basin of 420 x 590 x 195mm size with pillar cock, C.P.Angular stop cock, long thread of approved make continental including SS bottle trap of necessary pipe connection up to the outside face of the wall, having Telephonic Black / Colour Granite of 180 mm thick fixed on Black Kadappa Framework, etc. Complete as directed by Engineer in charge.

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete.

Providing and fixing divertor with overhead shower,shower arm,spout,hand shower with wall bracket having flow rate up to 12 liters/minutes of Jaquar/Cera/Hindware /Perryware or equivalent make including all necessary pipes,fittings etc.complete as directed by Engineer In Charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)

Providing and fixing wall mixer with overhead shower,shower arm,hand shower with wall bracket having flow rate up to 12 liters/minutes of Jaquar/Cera/Hindware /Perryware or equivalent make including all necessary pipes,fittings etc.complete as directed by Engineer In Charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)

Providing and fixing C.P. a 2-Way BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.

Providing and fixing reinforced cement concrete cover of size 90 cm x 45 cm with frame over inspection chamber etc. complete. Heavy duty (225 Kilogram)

Providing and applying Royale Luxury Emulsion of approved make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. wall primer with brush by adding mineral turpentine oil by 8 to 10 % or water by 15 to 20% allowing to dry for 6 to 8 hoursAfter applying acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45% or 65 to 70% by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45% or 65 to 70 % by roller. (With prior approval of S.E.)

Providing and applying plastic emulsion paint of approved quality, colour and shade to new surface in three coats including scaffolding, preparing the surface. (excluding primer coat) etc. complete.

Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases(NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram/15 l). plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist.

Providing and applying textured matt finish paint Dholpuri texture with biscuit cut or approved equivalent make to external surfaces in three coats paint additional coats if required shall be at the cost of the contractor) as per manufacturers specification and technical manual including required cleaning of the surfaces, curing, required scaffolding / staging / temporary hoisting etc. complete

Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top, 40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete

Supply & Fixing of Rock / Stone Finished outdoor vitrified flooring Tiles

Providing and laying Gangsaw granite flame /rough stone of 18 to 20 mm thick for Deck Swimming pool side flooring etc. On C.M. 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing, etc. complete.

Adhesive Grouting For Tiles As directed by Engineer In charge

Providing and laying machine cut mirror polished approved coloured ITALIAN MARBLE SLAB approved size,20 mm +/- 2 mm thick of approved quality with approved qality,italian marble inlays for flooring in required pattern on a bed of 1:4 cement mortar 2

ITALIAN MARBLE CLADDING Providing and laying machine cut mirror polished approved coloured ITALIAN MARBLE SLAB with inalays of approved size,20 mm +/- 2 mm thick of approved quality with approved qality,italian marble inlays for flooring in required pattern on a bed of 1:4 cement mortar 25 mm average thickness including neat cement float joints with neat colored cement slurry, curring polished and cleaning complete. (Basic rate of ITALIAN Marbel 6450/-per Sq. M)

Bissaza Tiles For swimming pool As directed by Engineer In charge

Providing and fixing Facility Building Outdoor Signages LED Made Of MS Febrication Hording & bracket &Supplying & Fixing of 4 mm X 0.50 foil Aluminum Composite Panel With 38mm X 25mm Aluminum Tube Framing, 12mm X 1.5mm Spacer Tape, Dow Corning Silicon Sealant . As per your Instruction.

Providing,aupplying,fabricating and fixing panel of aluminium composite panel cladding in approved shape made out of 4 mm thick ACP sheet material consisting of 3mm thick FR grade mineral core following NBC part IV Fire and life safety (having 2 hours fire resistance in accordance to ASTM E119-12 and BS476 part 6 and 7 class O) sandwitched between two aluminium sheets (each 0.5 mm thick of AA 5005/AA3105 grade) The aluminium composite panel cladding sheet shall be coil coated with kynar 500 based PVDF/Lumiflon based fluropolymer resin (having 70:30 ratio of PVDF and acrylic) coating of approved colour and sg=hade on top face and polymer (service) coating of bottom face as specified using stainless steel screws,nuts,bolts,washers,cleats,weather silicon sealent,backer rods etc .overall weight of the ACP shall not be less than 7.5 Kilogram/ One Square Metre)

Providing and Fixing Steel or Acrylic Letters with LED Made Of MS Febrication Hording & bracket

Providing and Fixing Acrylic TMC Logo

Tensile fabric roofing - PVC COATED FABRIC Fabric patterning, Supply, Fabrication & Installation of MEHGIESVALMEX MEHATOP F1 TIO2 FR-900/ Preconstraint TX30 of approved Colour 900 GSM Fabric for covering MS structure (Include : Material : of MEHGIES VALMEX MEHATOP F1 TIO2 FR-900 Type II fabric, with 15 years warranty from manufacturer back to back, Membrane Plate, Wireropes, Nut Bolts, Ites Require Accessories, Aluminium Section, Sds Screw, SS. 316 GradeTerminal, Service: Supply, Transport, Total Station Servey and Structural Steel etc) Rate includes Purchasing of fabric (including Cost, Insurance and Freight etc), shop drawings. Fabrication (including Cutting and High frequency welding to obtain the form), Transport to the site, assembling, Installation etc. complete as per direction of In charge

Providing and Laying Ultra Thin White Topping (UTWT)concrete overlay incorporating Graded Fibrillated 100% virgin polypropylene fibres,Micro-silica, fly ash and plastisizer,of approved makes as per specification including milling the existing bitumen surface of 55mm two pass ,formwork,placing,compacting and curing the concrete for 14 days etc complate. As directed by Engineer-In-Charge.

Providing and fixing at all height false ceiling of 12.5 mm thick tapered edge gypsum board conforming to IS: 2095 including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanized in accordance with zinc coating 600 as per IS: 277 and consisting of angle cleats of size 25 mm wide X 15 mm thick with flanges of 22 mm and 37 mm at 1200 mm centre to centre one flange fixed to the ceiling with dash fastner 12.5 mm dia X 40 mm long with 6 mm dia. Bolts to the angle hangers of 25 X 25 X 5 mm of required length, and other end of angle hanger being fixed with nuts and bolts to 6.1 channels 45 mm X 15 mm X 0.9 mm running at the rate of 1200 mm centre to centre to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450 mm centre to centre shall be fixed in a direction perpendicular to 6.1 channel with connecting clips made out of 2.64 mm dia. X 230 mm long 6.1 mm wire at every junction including fixing the gypsum board with ceiling section and perimeter channels

Providing and fixing mild steel grill railing 20 Kilogram/sq.m with teak wood hand rail of size 75mm x 60 mm.and sill of 75mm.x 25 mm.and newel posts for staircases, including fabricating, fix-tures, erecting, painting the grill work with one coat of anti-corrosive paint and two coats of oil painting with approved colour and polishing the sill,

P/F G.R.C sheet panels to columnade.GRC to be fabricated using cement and fine aggregate (sand) reinforced with alkaline resistancefibreglass strand.The panels are to be formed in GRC to achieve the design intent as indicated in the Architect’sdrawings and/or the approved proposed design as submitted by the contractor.Panels shall be resistant to water penetration and no dampness shall be visible on the inner face ofthe panel.The dry density of the GRCshould not be less than 1700 kg/m³

Designing, Conceptualization & painting of 3D artistic on any surface at all height and location as directed. The paint should be used for the artistic painting is high quality acrylic paint. painting should be coated with weather proof warnish.

Providing and Fixing Processed Stone Cladding on wall surface/ plywood surface. RCC pardi/ Wall and all type of Interior, Exterior Compound wall and Gate etc. of cladding processed stone with material of Processed clay, Wooden chips, Silica sand, Cement, GFRC admixtures, Colour pigments, Fiber up to thick of 230 mm/ 25 mm including scaffolding, fixing of screw, etc. (As directed by Engineer in Charge)

Dry wall cladding with clay tile; Designing, supplying and fixing of Clay tile of Wienerberger (Red Series or Grey Series) or Equivalent with suitable size and thickness not less than 20 mm as per manufacturer with approved colour and pattern with composition of finest powdered clay and colour mixtures. The clay tile shall be fixed on the suitable farming system by using continuous aluminium profiled section as per manufacturer with suitable size and spacing to withstand the structural design criteria specifled in the technical specification by using necessary HDG brackets, SS316 grade anchor bolts etc as per manufacturer specification. Cladding joints should be with open groove system. with prior approval of concerned Superitending Engineer.

Machine polishing to cement/marble mosaic tiled flooring or any other type of flooring including cleaning, washing, etc. complete.

Provding and Laying Wooden Flooring Brazillian IPE deck / equivalent make thickness 12mm in room flooring.IS 15622:2006/ ISO 13006:2012 Group B1a. As directed by Engineer-In- Charge.On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.

Providing and applying 100 % solid , flexible , elastomeric , UV stable, 2-component , water proof , fast setting (within 45 seconds) , specific grade Polyurea Coating at 1.2 mm nominal thickness on concrete surface on inner side of reservoir forming a seamless & monolithic membrane over compatible epoxy primer . The coating should have been tested and conform to various standards as mentioned in Data Sheet of the manufacturer. The coating shall be carried out in a single application with multiple passes using high pressure plural component reactor strictly as per manufacturers specifications including all necessary tools , tackles , high pressure spray machine , primer application , surface cleaning by sweep blasting/ grinding and filling up opened up bug holes etc using epoxy primer mixed with fine silica sand ( FQ 75). Application to be carried out by trained applicator certified by the principal. Necessary safety gadgets for worker using high pressure equipment & spray painting such as Boiler suit, helmet , safety shoes, nose mask, goggles, hand gloves to be provided by the painting contractor . Testing of the coating for DFT, Adhesion , Hardness and finally by filling water in the tank ( water filling not in the scope of painting applicator ) and checking against any leakage. The coating to carry a warranty for 10 year against material and application fault. Surface to be coated with Poloyurea to be handed over to Painting Contractor by Civil Contractor should be bone dry ( with surface moisture preferably below 5% and maximum limit at localized area up to 8% ) and repaired of construction surface blemishes if any with suitable repairing compound ( polymeric mortar / epoxy mortar) etc. complete as directed.

GARDEN SOIL :- Supplying on site garden soil well sieved 90% to pass through I.S. sieve of 10mm size Free from stones rubbish like dried grass roots and other such materials. The soil should be fresh be measured by measuring box (Farma) Item includes royalty charges, octroi, corporation Tax Transporting, loading – unloading etc

Farm yard manure :- Supplying on site well decayed, well dried, well powedered, withought clods and free from stones, dried grass and other rubbish material,. The colour of the manure generally be black. the manure will be measuring by measure box. (farma) item includes Transporting, loading -unloading etc (lead charges per 40km. are considered.

Preparing Instant Lawn : Excavating the ground to a required depth of 20cms removing & conveying unwanted stuff to a required distance as directed. filling fresh garden soil / silt & manure in excavated area in 3:1 proportion to a height of 20cms. Mixing garden soil and manure thoroughly will levelling, watering on previous night. Planting required variety of lawn grass as directed and maintaining till well established by watering weeding clopping rolling etc. complete

Preparing Shrubbery :- Excavating the round to required depth of 30cms, removing and conveying unwanted stuff to a required excavated area in 3:1 proportion to a height of 30cms. Mixing garden soil & manure toughly well, leveling , watering on previous

Supplyings & planting of plants required for landscaping:- Euphorbia, hemelia, Malphejia, Ticoma, song of India, Golden bamboo, Bhudhhaj bamboo, golden ficus, Phonicu palm, x mass trees ficus panda, etc. (height of plant 5-6 ft )

Palm Variety- (red palm, fox tail palm, bottle palm, rhaphis, table palm, crystal palm…etc

Planting large flowering / shady trees :- Digging pit with size 0.9m x 0.9m x 0.9m removing and conveying unwanted stuff to a required distance as directed. Filling the pit with approved excavated material upto a height of 0.30m and remaining height of 0.60m with fresh garden soil & manure in 3:1 proportion Mixing soil & manure thoroughly well. leveling as directed, watering previous night, planting on to two year old healthy trees sapling as per specifications. Maintaining till well established by watering weeding, stirring of soil replacing of casualties etc. complete.

Providing forest trees putranjiva, jaccaranda, bakula, kecia, Neem, shoka Gulmohar 8 feet to 10 feet.

Providing detailed geological reports of proposed site by maintaining geotechnical investigation of structure stratification collecting soil, rock and ground water samples for laboratory tests to arrive the foundation design parameters . Rock properties such as type of rock, jointing fractures, etc. complete with suggestion about the site foundation and remedies.

Soil Test - Complete Soil test with 2 Bore logs, etc. complete as directed by Engineer in charge.

Concrete Tests - Compressive Strength OF C.C. Cube (Set of 3 cubes).

Steel Tests - Upto 16 mm (Set of 3 Bars)

Brick Tests - Water Absorption (Set of 5 Bricks), Compressive Strength( Set of 5 Bricks), Efflorescence (Set of 5 Bricks).

Tile Tests - Water Absorption, Modulus of Rupture (Set of 6 Tiles)

Providing & Arrangemnt of High Back, Synchronized Mechanism with Multiple Locking, 2d Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Leatherite Upholstery (Chair)

Providing & supplying high counter stool or bar chair with 36 to 38 inches high

supply and installation of WOODEN chair- 1'-8"X1'8"X3'-0" using sisham wood with carving works and seat of super high density foam in good quality rexine/fiber upholstery, all complete as per drawings, specification

Supplying and installing L - Shape main Reception table, supply and installation with - 4'7" x 2'0" x 2'7" and 7'0" x 2'0" x 2'7" ,using solid wood with melamine polish and 10mm edge polished glass top with 4" spacer. All the drawers must be fitted with heavy duty metal runner at both side. The locks and handle must be high quality all complete as per drawings, specification and instruction of Engineer.

supply and installation of Officer table - 3'10"x 1'6"x2'5" with structure made using solid wood with melamine polish and finished with intricately carved vintage art . All the drawers must be fitted with heavy duty metal runner at both side. The locks and handle must be high quality all complete as per drawings, specification and instruction of Engineer.

supply and installation of Coffee table, walnut veneer, 180x59 cm Top: Fibreboard, Walnut veneer, Clear acrylic lacquer, Paper foil, StainLeg:Solid walnut, Clear acrylic lacquerPanel:Unbleached paper, Clear acrylic lacquerUnder frame/ Panel/ Underframe: Steel, Epoxy/polyester powder coating all complete as per drawings, specification and instruction of Engineer.

Restaurant Tables Restaurant Tables Size: 2'8” x 2'8” x 2’11” Providing and supplying Restaurant Table with Laminated top. Table frame made from 3” Round x 1.6mm thick M.S. CRCA Pipe with 50mm x 25mm x 1.6mm thick rectangular M.S. CRCA ERW tube. Frame finish with desire colour of powder coating. Table top made from 25mm thick MDF board laminated with 1mm thick laminate on top and 0.8mm thick liner as back. All four edge should be closed with 2mm thick Rehau or equ. Make edge bend.

supply and installation of L- Shape snack counter table with 14'2" x 2'6"x 3'0" and 5'6" x 2'6" x 3'0" structure made using solid wood with melamine polish and finished with intricately carved vintage art . All the drawers must be fitted with heavy duty metal runner at both side. The locks and handle must be high quality all complete as per drawings, specification and instruction of Engineer.

supply and installation of PANTRY table with 5'7" x 2'0" x 3'0" structure made using solid wood with melamine polish and finished with intricately carved vintage art . All the drawers must be fitted with heavy duty metal runner at both side. The locks and handle must be high quality all complete as per drawings, specification and instruction of Engineer.

Providing Single Seater Sofa(Type-i) for commonroom of size 2’- 7”(L)x2’-0”(W) x 2’-7” (ht) with basic framework made in first class Hollock/Mirandi wood (kiln seasoned and chemically treated,), the base for sofa cushions to be made a layer of steelSprings uniformly distributed across the length and breadth of sofa framework supported on frame of hillock wood and base of ply and jute layer , gaps to be filled with coir of foam fillers and top layer to be made of a class jute sheet encompassing min. 50mm foam (Sleepwell/Kurlon make).This layer in turn shall be finished with A- class Molfino fabric (Ddecor or equivalent make)(color and texture as approved by NIB) with sewn seams to be multi top stitched. The seat shall have 150mm thk.(minimum) removable cushions placed on the finished seta, which shall be duly upholstered with A-class molfino fabric (Ddecor or equivalent make) (color and texture as approved by NIB), fixed with a zipper on lower side (for ease in maintaince cleaning)..

Sofa Three Seater: Providing Three Seater Sofa (Type-i) of minimum size (6'-8"(L) x 2'-4"(Depth) x 1'-9" ( seat height.)x2'7"(fixed back rest) with removable cushions (back rest) with basic framework made in first class Hollock/Mirandi wood (kiln seasoned and chemically treated,), the base for sofa cushions to be made a layer of steel Springs uniformly distributed across the length and breadth of sofa framework supported on frame of hillock wood and base of ply and jute layer, gaps to be filled with coir of foam fillers and top layer to be made of a class jute sheet encompassing min. 50mm foam (Sleepwell/Kurlon make).This layer in turn shall be finished with A- class Molfino fabric (Ddecor or equivalent make)(color and texture as approved by NIB) with sewn seams to be multi top stitched. The seat shall have 150mm thk.(minimum) removable cushions placed on the finished seta, which shall be duly upholstered with A-class molfino fabric (Ddecor or equivalent make)(color and texture as approved by NIB), fixed with a zipper on lower side (for ease in maintaince cleaning)..

Providing and supplying CARROM BOARD WITH TABLE , 2'8" x 2'8 x 2'11" structure made using solid wood with melamine polish and finished

Providing and supplying pool table and equipments, structure made using solid wood with melamine polish and finished

Providing and supplying table tennis and equipments

Supplying and fixing of 15mm Toughened glass patition with profile channel of top & bottom patch fitting as per instruction.

Providing and fixing glass doors with all necessary handle , fixing ,patches, including locks at bottom side etc.

Automatic sliding door system having maximum opening 2000/2x2.100 mm, maximum weight of the door is 70-80 Kg, DC 24V 60W herical gear motor, 55-60 DB noise level, built-in motor lock and ( DORMA/OZONE) with all necessary handle, fixing ,patches, including locks at bottom side etc.

Providing and fixing mirror including necessary engraving & necessary fixture etc complete.

Glass top for tables Providing and laying 5 mm glass for table top cut to size as per the table with smooth machine edge polishing. Necessary cutting shall be made for the fixing 75 mm/100 mm cable managers in the table.The item will mesured in the finished surface area and no wastage will be paid.

Electronic Safe Locker For Shower Room With Pin Code & Key Access,34.70 Kg (440 W x 405 D x 650 H) mm as per drawing as specification, with all fitting , locks, handles , finishing etc (GROUND FLOOR)

Providing and fixing seating bench in shower room, 0.9 x 0.35 x 0.45 m, structure made using solid wood with melamine polish and finished with intricately carved vintage art , must be high quality all complete as per drawings, specification and instruction of Engineer.

providing and supplying outdoor and indoor bin for 180 litre in public places

providing and supplying parasol Made From High Quality Polyester- tafta Fabric This Is All Season Umbrella Suitable For 4 Person Ideal For ...

providing and supplying Pool side lounger (bed) with High Quality,

providing and supplying , lifeguard chair for an unblocked view of the water and swimmers from an elevated position and typically made of wood or resin

providing and supplying , Starting block

providing and supplying , Lifebuoy rings with J hook

providing and supplying , Lifejacket

providing and supplying , rope lane

Providing and supplying Automatic or Motorized treadmills In gymnasium , the device provides a moving platform with a wide conveyor belt driven by an electric motor or a flywheel Spec- As Derected Engineer-In- Charge.

Providing and supplying Adjustable training bench in gym Spec- As Derected Engineer-In- Charge.

Providing and supplying dumbbell Bodyfit 30Kg Gym 4-In-1 Multi Leg Curl Bench Home Gym Dumbbell Set 30Kg Weight Plates: 2.5 Kg x 4 = 10 Kg + 5 Kg x 4 = 20Kg 4In1 Bench, 1X5Ft Rod, 1X3Ft Curl Rod, 2X14Inch D.Rods or equivalant Spec- As Derected Engineer-In- Charge.

Providing and supplying kettle bell set Spec- As Derected Engineer-In- Charge.

Providing and supplying pull up frame and bar Spec- As Derected Engineer-In- Charge.

Providing and supplying Stationary bicycle Spec- As Derected Engineer-In- Charge.

Providing and supplying elliptical machine Spec- As Derected Engineer-In- Charge.

Providing & Supplying Leg Curl / Leg Extension Spec- As Derected Engineer-In- Charge.

Providing & Supplying Seated calf Spec- As Derected Engineer-In- Charge.

Providing & Supplying Adjustable decline benchSpec- As Derected Engineer-In-Charge.

Providing & Supplying Squat rack Spec- As Derected Engineer-In- Charge.

Providing & Supplying Power cage Spec- As Derected Engineer-In- Charge.

Providing & Supplying Leg press Spec- As Derected Engineer-In- Charge.

Providing & Supplying Doumble rack. Spec- As Derected Engineer-In- Charge.

Supplying and installation of gym rubber flooring with a thickness between 10 to 50 mm top 5 mm layer of the surface rubber tile pigmented with 0.8 to 2 mm crumb rubber granules and polyurethane polymerically bonded ASTM and DIN standard approved. hardness A60 (ASTM D2240), Tensile strength 1.29 (DIN 53304 Force 55.4 N), elongation break 47% (ASTM D573). Tear strength 40.1% strain @break,specific gravity 0.88, compression set 7.23 Mpa, operating temperatures 140-150 degree celsius . UV Exposure (150*C) by chemical analysis ISO 4 SBR Blend rubber no effect. ASTM 0.45 noise reduction coefficient (NRC), ASTM D2859 Pill flamability excellent pass. ASTM E30393 Skid resistance excellent pass. Spec- As Derected Engineer-In- Charge.

FIRE HYDRANT SYSTEM Providing, laying and jointing in position G.I. heavy duty C class pipes confirming to I.S. 1239 with welded joints for pipes and flanged joints for valves and accessories including all fittings including cutting the pipes to correct length, providing and welding M.S. flanges for connection to valves and accessories, providing epoxy coating to welded surface, testing to 1.5 times working pressure, including painting the pipes with bituminous paint and wrapping the pipes with IWL (Pypkote) wrapping of 4mm thk as per manufacturers instruction all complete including with haliday test upto satisfaction of Engineering Incharge, all excavations in any type of soil, refilling the trenches after testing disposing of surplus material, dewatering etc. complete all as per directions for the following diameters. 150 mm dia.

100 mm dia.

80 mm dia.

65mm dia.

50 mm dia.

40 mm dia.

32 mm dia.

25 mm dia.

Galvanised iron "C" class pipes(IS1239 Part - 1 including cutting, screwing, welding etc. complete with fittings viz. tees, elbows, bends, flanges, reducers etc including excavations (upto 1.5 m deep) p:c:c 1:2:4 thrust blocks, back - filling with excavated earth, removal of surplus soil and providing anti-corrosive treatment (coating and wrapping) as per IS: 10221 complete as required for all external hydrant system piping 200 mm dia.

150 mm dia.

100 mm dia.

80 mm dia.

15 mm dia. quartzoid bulb type G. M pendent sprinkler head set to operate at 68 Deg C (rate in rise) and as per IS 9972

Providing and fixing in position 100 x 80 mm size tee junction on the wet riser, flanged or welded for fixing to the Double outlet hydrant valve including hydraulic testing, painting etc. complete

Providing and fixing approved drum type wall mounted hose reels, swivelling 180 degrees consisting of 20mm dia x 30 m long best approved , armoured rubber hose pipe with 6.3 mm dia bronze shut off type jet nozzle, making connection to the vertical riser by cutting welding, including providing 20mm dia shut off valve, all necessary piping, fittings, fixing the hose reel with necessary anchor fastners by drilling holes in walls /RCC, making good the same all complete as per direction of the Engineer-in- charge

Providing and installing in position 2 lengths of 15m long and 63mm dia non-perclating RRL Fire Hose (as per IS 636) along with couplings, short size gun metal branch pipe with 16mm gun metal nozzle, housed in a metal box with lockable glass doors and painted post office red,

Supply and installation of M.S Cabinet with glass and locking arrangement , suitable for 2 lengths of RRL hose and 1 no of Branch pipe, 2 coats of primer paint as per seven tank process and powder coated finally in post office red etc. complete Size 1000mm x 750 mm

Providing and fixing courtyard fire hydrants as per IS 5290, consisting of 63mm dia, single outlet flanged oblique type hydrant valve with instantaneous female plunger type coupling, chained blank cap including making flanged joints by providing necessary nuts, bolts, gaskets (6 mm thick neoprene) all complete as suitable for 80mm dia stand post.

Providing and fixning fire Brigade inlet Siamese connection fabricated from 100 mm G.I. pipe with 4 nos 63mm dia G.M. male hydrant connection including providing and fixing 100 mm dia Butterfly valve, non return valve etc. for the wet riser, etc complete

Providing and fixing bronze orifice disc for fire hydrant system and courtyard hydrants to control the pressure within 5.5 kgs/cm2 including rubber gasket packing, bolts, nuts, washers, all complete as per direction of the Engineer - in – charge

Providing and fixing C.I. air release valve of 40 dia and G.I. drain pipe of 0.5mt length including necessary support and painting with two coats of enamel paint over a coat of primer etc. complete, for wet riser termination.

Providing and fixing .Ball valve of 40 mm dia. and GI drain pipe of 0.5 length including necessary support and painting of two coats of enamel paint of approved colour over a priming coat etc complete on the lower end of the

Providing and fixing in position cast iron butterfly valve standard pattern (Horizontal / Vertical) of pressure rating PN 16 including necessary flanged joints by providing necessary nuts, bolts, gaskets, etc. all complete of the of the following diameters 100 mm dia

Providing and fixing heavy approved quality cast iron dual plate type non return valves (PN-16) Flap to be of CI while Flap seat ring to be of GM. including making joints etc all complete for the following diameters . 100 mm dia

Providing horizontal monoblock centrifugal booster pump having cast iron casing bronze impeller, EN 8 shaft driven by 7.5 HP including Concrete Foundation for Booster Pump.

Providing and fixing pressure gauge, glycerine filled with isolation valve

providing and fixing of starter of Booster pump

Booster pump Cabling 2.5sq x 6 core armoured cable

SITC of Core Cutting 6"

Electric motor driven fire hydrant system pumping set suitable or automatic operation consisting of the following:

Electric motor driven automatic pressurisation (Jockey pumps) consisting of folloing:

Cubical type floor mounted main fire pump control panel fabricated from 16 G M.S. sheets duly painted with stove enameled finish off approved shade suitable for the fire / jockey pumps and complete with incoming and outgoing switchgear, bus bars, starters, indicating lamps, volt meter, ammeter and all inter connecting power and pressure switch control cabling extra from plate and as directed.

Electric motor driven fire hydrant system pumping set suitable or automatic operation consisting of the following: A) Horizontal, centrifugal, end suction fire pumps having cast iron body, bronze impeller, stainless steel shaft & capable of delivering 2400LPM against a total head of 76 M complete with necessary pressure guage & pressure switch on the delivery side including bypass arrangement as required for periodical testing of the working of the pumping sets also with nrv,ystrainer & valves complete in all B) Squirrel cage induction motor totally enclosed fan cooled type suitable for 400 / 440 volts (+5%) 3 phase, 50 HZ, A.C. supply of suitable capacity for the above mentioned pumps with synchronous speed of 3000 RPM confirming to IS:325 and duly coupled with above pumps with flexible coupling including earthing as per relevant Indian Standard

ISI marked (IS:13849) portable fire extinguishers, ABC dry powder type of capacity 5 Kg with pressure gauge, discharge hose and nozzle and complete in all respects including initial fill.

4 Nos fire buckets 9 lts capacity each made out of 24g GI sheet with round bottom, painted with white synthetic enamel from inside and fire red from utside and lettered 'FIRE' in black complete with bucket stand etc. complete including initial fill of sand.

Bitcon India Infrastructure Developers Pvt Ltd