Construction of the Administrative Building Complex up to the 1st Floor with the foundation provision of G3 at Tea Park, Chaygaon Dist Kamrup R, Assam

Amount

Machine driven RCC pile: Providing cast in-situ machine driven reinforced cement concrete piles of any length of required bore-diameter and with reinforcements as per specifications and drawings. Reinforcement to be measured and paid seperately as per item no. 21.4.1 A) M20 grade concrete iii) Pile Dia 450 mm

Extra for using admixture (Masterplast PI-1 or equivalent) and accelerating plasticiser (conforming to IS-9103-1999 , Masterplast APCL or equivalent) for RCC concrete as specified and directed. a) RCC grade M20 iii)Pile Dia 400 mm

Empty boring for specified diameter piles from ground level to cut-off level. iii) 400 mm dia

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to propoe shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. A) For TMT bar (TATA TISCON/SAIL)

Routine test for test loading to 1.5 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Initial test for test loading to 2 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load) (Minimum three(3) nos of initial load test to be done)

Earthwork

Surface dressing of ground including removing vegetation and/ or undulation of ground not exceeding 150mm deep and disposal of rubbish outside the periphery and lift up to 1800mm in all kinds of soil.

Jungle clearance including uprooting of vegetation, grass, brush-wood, sapling and trees not exceeding 300mm girth and disposal of the same outside the periphery and lift upto 1500mm

Earthwork in excavation for foundation trenches of walls, retaining walls, footing of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. Up to a depth of 2.00m below the existing ground level (a) In ordinary soil

Earth/sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

ANTI-TERMITE TREATMENT

Pre construction anti-termite treatment with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or equivalent) and water. This provides emulsion containing 1% chloropirophose solution (by weight)- at the bottom of foundation pits and walls on either side up to a height of 300mm from bottom of the excavation made for column, plinth beam, wall, trenches etc. by applying the emulsion @ 5 liters per square meter of the surface area before starting construction work (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. b) with aqueous emulision having concentration 1:499 with Premise 350 SC (imidachloprid 30.5% SC) and water i.e.0.07% solution

Pre construction anti-termite treatment by applying the emulsion @ 5 (five) litres per square meter of the surface to be spread with light rodding so as to ensure proper absorption by the filled up earth (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete.b) with aqueous emulision having concentration 1:499 with Premise 350 SC (imidachloprid 30.5% SC) and water i.e.0.07% solution

PLAIN CEMENT CONCRETE WORKS

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).(a). In prop. 1:3: 6 (1 cement:3 coarse sand : 6 coarse agg. by volume (using mixture machine)

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 100mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacture including curing etc. complete as directed.

PLINTH PROTECTION AND DRAIN:

Providing plinth protection 50mm thick to cement concrete 1:3:6 with coarse agg.of 20mm nominal size including finishing the surface with 10mm thick cement plaster in proportion 1:3 with a floating coat of neat cement finished.

Providing drain with cement concrete (1:3:6) 100mm thick sides 100mm thick bed over brick flat soling including 15mm thick cement plastering in proportion 1:3 finished coat of cement slurry as directed with necessary shuttering for sides and earthwork in excavation of foundation trenches and refilling the sides after completion of work etc as directed. 300mm wide and average 150mm deep with bed slope 1 in 150 with initial depth of 100mm.

REINFORCED CEMENT CONCRETE WORKS

Providing and laying plain/reinforced cement concrete works in prop 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone chips, 20mm down) including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (i)In substructure up to plinth level. Foundation, footing, column with base, tie and plinth beam, grade beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick.

Providing and laying plain/reinforced cement concrete works in prop 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone chips, 20mm down) including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (i)In super structure above plinth. (ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase, ramp including preparing of top surface and furnishing and nosing.(up to first floor)

FORM WORK

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: (a) Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: . Using 25mm thick plank(b) Sides of tie beams, plinth beams, grade beams etc. at or below plinth level.

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: . Using 25mm thick plank(b) Sides of tie beams, plinth beams, grade beams etc. at or below plinth level.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. Floors etc. upto 200mm in thickness.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in Flat Surfaces such as Staircase with sloping or stepped soffits including risers and stringers but excluding landing. (Using 38mm thick plank)

REINFORCEMENT

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (up to 1st floor level). Super Ductile TMT bar TATA\SAIL

Brickwork

Providing brick soling in foundation and under floor with stone/best quality picked jhama brick, sand packed and laid to level and panel after preparing the sub-grade as directed including all labour and materials and if necessary dewatering, complete. Brick on flat soling.

Brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary, and curing complete as directed in sub-structure up to plinth level (d). In proportion 1:4.

112 mm thick 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (i) In super structure up to 1st floor level. a) In cement mortor in proporation 1:4

112 mm thick 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) a) In cement mortor in proporation 1:4 In super structure above 1st floor level

(a).Extra for brick walling for each subsequent floor or part thereof above the 1st floor level (i).112mm thick brick/ R.B wall

Railing

Providing and fixing Stainless Steel railing made of Hollow tubes, channelas, plates etc., including welding, grinding,buffing,polishing and making curvature and fitting the same with necessary stainless steel nuts and bolts complete, i.e. fixing the raling with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in charge. (c). Fixed to Brickwork/P.C.C/R.C.C.

Plastering

15mm thick Cement plaster in single coat on rough side of brick/concrete walls for interior plastering up to 1st floor level including arises, internal round angles, chamfers and/ or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. (i)In Superstructure upto 1st floor Level. In Cement mortar 1:4

Extra over for exterior plastering over wall up to a height of 1st floor level above ground level including curing complete as directed. a) On Single coat plaster

15 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. (i)In Superstructure upto 1st floor Level. (b). In cement mortar 1:4

15mm thick Cement plaster in single coat on ceilings for interior plastering including arises, internal round angles, chamfers and/ or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. (ii)upto 1st floor level. In Cement mortar 1:3

Extra over items for interior plastering above 1st floor level for every addl floor or part thereof including curing complete as directed.a) On single coat plaster

FLOORING, SKIRTING/ DADO AND TILES

Plain cement concrete floor base in prop.1:3:6 laid in alternate bays as specified with coarse aggregate of size 13 mm to 32 mm including dewatering if necessary and curing etc. complete (i) 50 mm thick.

Wall Tiles

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls).ii) (size 300mmx450mm). c) Delux range Somany / Orient / Nitco / Varmora make

Floor Tiles

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) c) Delux range (Sizes 1000 mm x 1000mm iii) Nitco vitrified made

Providing ANTISKID tiles of approved quality size,shape not less than 8 mm on floor,skirting over a cement mortar bed 15 mm thick of 1:3 (1 cemen:3coarse sand) of approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement complete at all level as specified and directed. CERAMIC TILES B)b) Delux range (sizes 1000mmx1000mm and above)

Providing polished tiles of approved quality, size, shape of specified thickness on pavers over a base of 100mm compacted sand gravel including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (a) Silicon (Pavers) 60 mm thick. (A) SUN ROCK HIGH CTS Tiles (Pavers)

PAINTING

Providing two coats of J.K Wall Putty ( White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth.(a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Applying priming coat over new wood based surfaces over 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. (b). With ready mixed paint , wood primer (white).

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surfaces of all dirt,dust and other foreign matter sand papering and slopping. i) Surfaces over 100mm in width or girth. a)General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Applying primary coat over new steel and other metalsurface upto 100m in width or grith after preparing the surface by throughly cleaning oil, grease, dirt and other foreign matter and scoured with wirw brushes, fine steels, wood scrapers and sand paper. a) With ready mixed :red-lead/ red-oxide: primer.

Painting two coats on new steel and other metal surface with enamel paint of approved brand and manufacture (Asian / Berger paint / JCI paint / J& N paint / Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. ii ) Surfaces up to 100 mm in width or girth. b) High gloss

DOORS/ WINDOWS & FITTING

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevant I.S code including oxidized iron butt hinges (100mm× 75mm×3.5mm) 6 nos. with necessary wood screws.(ii) 35mm thick. a) Decorative type face panel and block board core.

Providing, fitting and fixing anodised aluminium framed double leaf doors of approved brand (HINDALCO/ NALCO/ BALCO/ JINDAL/ Other equivalent primary producer) with styles size 45mm x48mm x 3.2mm, top rails 50mm x 45mm x2.5mm, lock rails 48mm x 45mm x 2.5mm, bottom rails 100mm x 45mm x 2.5mm fitted with tapper clips of size 20mm x 15mm x 1.2mm complete with automatic floor mounted door closure,m butterfly type handles, special cylindrical lock, concealed type aluminium tower bolt, neoprene, dryset rubber gasket, door felt gusket, etc. complete as directed by the Department at all levels. (iV)6mm coloured glass

a) Providing , fitting & fixing anodised aluminium fixed windows and ventilators of standared sections of approved brand .i) With 6mm thk glass panes. a) in coloured anodised aluminium

Providing, fittin g and fixing poder coated pressed steel door frame made of 125mm/1.6 mm thick sheet of various sizes with necessary hings jamb, lock jamb, head and steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed together by mechanical means with base ties of pressed mild steel angle of sixe 20x20x1.25 mm thick, Frame to be filled up with 1:4:8 P.C.C. after fitting the frame with brick/ concrete works etc. complete as directed by the department for all levels. (a) 1.25 mm thick sheet. iv) Size 165mmx60mm (double rebate)

Providing fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ opening with M.S flats at required spacing in frame all round, squre or round M.S bars with round headed bolts and nuts or screws. I) Plain grill a) Fixed to Brickwork/ P.C.C./R.C.C.

Supplying, fitting and fixing anodized aluminium fittings of approved make, reasonably smooth, free from sharps edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete. (anodized to bright natural matt &stain finished)

Supplying, fitting and fixing anodized aluminium fittings of approved make, reasonably smooth, free from sharps edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete. (anodized to bright natural matt &stain finished)(a) Sliding door bolts. (ii) 250mm×16mm

Supplying, fitting and fixing anodized aluminium fittings of approved make, reasonably smooth, free from sharps edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete. (anodized to bright natural matt &stain finished).(ii) 250mm×12mm. (b) Tower bolts

Supplying, fitting and fixing anodized aluminium fittings of approved make, reasonably smooth, free from sharps edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete. (anodized to bright natural matt &stain finished).(ii) 150mm×10mm. (b) Tower bolts

Supplying, fitting and fixing anodized aluminium fittings of approved make, reasonably smooth, free from sharps edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete. (anodized to bright natural matt &stain finished).(c) Door handles ii) 100mm

Supplying, fitting and fixing anodized aluminium fittings of approved make, reasonably smooth, free from sharps edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete. (anodized to bright natural matt &stain finished). Door Handles (iii) 150mm

Supplying, fitting and fixing anodized aluminium fittings of approved make, reasonably smooth, free from sharps edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete. (anodized to bright natural matt &stain finished). (r) Curtain rod. ii) 25mm x 2mm thick

Water Supply works

Providing and fixing S.F.M.C. Brand 3 layer (Outer green coloured UV Stabilised, middle black coloured UV Stabilised and inermost layer white coloured with antimicrobial property) Fusion welded PP-R (Poly propylene- random copolymer) Pipes, SDR 7.4 having thermal stability for hot and cold water supply including all plain PP-R fittings and brass threaded PP-R fitting and clamping, cutting and making good to the damages. Concealed pipe with cutting chases & making good the wallsa) PN-16 Pipe,16mm OD,SDR-7.4

Providing and fixing S.F.M.C. Brand 3 layer (Outer green coloured UV Stabilised, middle black coloured UV Stabilised and inermost layer white coloured with antimicrobial property) Fusion welded PP-R (Poly propylene- random copolymer) Pipes, SDR 7.4 having thermal stability for hot and cold water supply including all plain PP-R fittings and brass threaded PP-R fitting and clamping, cutting and making good to the damages. Concealed pipe with cutting chases & making good the wallsb) PN-16 Pipe,20 mm OD,SDR-7.4

Providing and fixing S.F.M.C. Brand 3 layer (Outer green coloured UV Stabilised, middle black coloured UV Stabilised and inermost layer white coloured with antimicrobial property) Fusion welded PP-R (Poly propylene- random copolymer) Pipes, SDR 7.4 having thermal stability for hot and cold water supply including all plain PP-R fittings and brass threaded PP-R fitting and clamping, cutting and making good to the damages. Concealed pipe with cutting chases & making good the walls c) PN-16 Pipe,25 mm OD,SDR-7.4

Providing and fixing S.F.M.C. Brand 3 layer (Outer green coloured UV Stabilised, middle black coloured UV Stabilised and inermost layer white coloured with antimicrobial property) Fusion welded PP-R (Poly propylene- random copolymer) Pipes, SDR 7.4 having thermal stability for hot and cold water supply including all plain PP-R fittings and brass threaded PP-R fitting and clamping, cutting and making good to the damages. Concealed pipe with cutting chases & making good the walls f) PN-16 Pipe,50 mm OD,SDR-7.4

Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and packing of pea gravel free from dirt, dust and other foreign materials in the annular space between the borehole and assembly pipes complete as directed by the Department. G.I. Pipe. (a) TATA/ SAIL (medium) (sockets should be welded to the pipes). (vi) 150mm diameter

Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and packing of pea gravel free from dirt, dust and other foreign materials in the annular space between the borehole and assembly pipes complete as directed by the Department. G.I. Pipe. (a) TATA/ SAIL (medium) (sockets should be welded to the pipes). (iv)100mm diameter

Supplying, fitting and fixing of PVC Pipe. (a) Supreme Brand. (vi) 140mm diameter

Supplying, fitting and fixing of STOP COCK. I) Brass stop cock of sant make (a) 20mm dia

Supplying, fitting and fixing of STOP COCK. I) Brass stop cock of sant make (b) 25mm dia

BIB COCK: Supplying fitting and fixing C.P. bib cock 15 mm dia of approved brand directed and specified. (G.I. & C.P. pipes will be measured separately ) Essco/ Agmeco make, Jaquare make. (a)Continental /Clarion (i)Standard

PILLAR COCK: Supplying fitting and fixing C.P. pillar cock 15 mm dia of approved brand directed and specified. (G.I. & C.P. pipes will be measured separately ) Essco/ Agmeco make , Jaguar make (a) Continental, Pillar cock (ISI) / Pillar cock

SINK COCK: Supplying fitting and fixing C.P. sink cock 15 mm dia of approved brand directed and specified. (G.I. & C.P. pipes will be measured separately ) Essco/ Agmeco make , Jaquar brand a) Continental / Clarion i) Sink cock with swinging casted spout

SHOWER: Supplying fitting and fixing overhead adjustable C.P. spray shower 15 mm dia of approved brand directed and specified. ( pipes will be measured and paid separately ). (a) Supreme shower with arm

VALVE: Supplying fitting and fixing gun metal country pit valve ( full way valve) ISI make as directed and specified. i) 40mm

BASIN MIXER: Supplying, fitting and fixing Chrome Plated (C.P.) basin mixer complete as directed. Crabtree Frattini make (For VIP use. Prior approval of Chief Engineer PWD (Bldg) must be taken before use). a) Florence i)Central hole basin mixer without pop-up Cat No.21051 for wash basin

Supplying and placing Fibre Glass Reinforced Plastic (FRP) water tank of National Associates make (rectangular/ cylindrical/ spherical/ panel) over the staging with manhole cover with locking and cleaning arrangement including providing pads of size as required. a) 2000 litre capacity

C. SANITARY WORKS

Supply fitting and fixing Supreme/ prince brand of 6kgf/cm2 or other similar ISI approved P.V.C. high pressure pipes of following sizes including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. ii) 110mm dia.

Supply fitting and fixing Supreme/ prince brand of 6kgf/cm2 or other similar ISI approved P.V.C. high pressure pipes of following sizes including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. iv) 75mm dia.

Supply fitting and fixing 87.5 degree PVC bend of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. ii) 110mm dia.

Supply fitting and fixing 87.5 degree PVC bend of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. iv) 75mm dia.

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia.

Supply fitting and fixing PVC plain single tee of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. ii) 110mm dia.

Supply fitting and fixing PVC plain single tee of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. iv) 75mm dia.

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia.

Supply fitting and fixing PVC single 'Y' of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. ii) 110mm dia.

Supply fitting and fixing PVC single 'Y' of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. iv) 75mm dia.

Supplying fiting and fixing PVC single ‘Y’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm dia.

Supplying fiting and fixing PVC single ‘Y’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 75 mm dia.

Supply fitting and fixing PVC coupler of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. i) 110mm dia.

Supply fitting and fixing PVC coupler of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. ii) 75mm dia.

Supply fitting and fixing PVC reducer of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. iv) 110mm x 75mm

Supply fitting and fixing PVC reducer of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. (viii) 75 mm x 63 mm

Supply fitting and fixing PVC socket plug of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified.a) 110mm dia.

Supply fitting and fixing PVC socket plug of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified.b) 75mm dia.

Providing fitting and fixing 110mm dia PVC cowel of ISI make complete as direction and specified.

Providing fitting and fixing C.P. Grating to the floors complete as direction and specified.b) 110mm dia

Providing fitting and fixing white vitreous china pedestal type watercloset (European type W.C pan 400mm high) of Parryware/ Hindware make with seat and lead ,CP brass hinges and rubber buffers, 10 litre low level white china vitreous flushing cistern with fittings, CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, cutting and making good the walls and floors whereever required.(a) white

Providing fitting and fixing white vitreous china flat back type lipped front urinal basin of (455x360x267)mm of Parryware/Cera make with automatic flushing cistern of similar colour and standard flush pipe and CP brass spreader with brass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. a) White(i) new magnum

Providing vitreous China wash basin of size 630mm x450mm of Parryware make with CI/MS brackets, 32mm CP brass waste coupling of standard pattern,C.P stop cock,C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. ii) Coloured vitreous china wash basin of size 550mm x440mm

Providing fitting and fixing decorative mirror of Agmeco make colour CP frame complete as directed and specified.

Providing, fitting and fixing recessed soap tray of Hindware make complete as specified and directed.(A) White

Providing, fitting and fixing chrome plated (CP) towel rail of Jaquar make complete as specified and directed.(a) ii)Continental Accessories (600mm long)

Providing, fitting and fixing chrome plated (CP) towel ring of Jaquar make complete as specified and directed.(a) i) Continental Accessories

Providing fitting and fixing chrome plated (CP) toilet paper holder of Jaquar make complete as directed and specified.(a)(i) Continential Accessories

SEPTIC TANK: Providing fitting & installational at site BIO= Septic Tanks for 100 users as per specification provided by the department

Providing fitting and fixing 450mm dia. 90mm thick C.I. Man hole cover and frame of 58 Kg. weight complete as directed and specified

Construction of filter bed in soak pit including earth work in excavation of soil and then filling up of the trench with brick bats/Charcoal covered with earth over a layer of A.C. plain sheet above brick bat filling complete as directed. (sizes of soak pit may vary depending on the sizes and capacities of the septic tank as well as the number of users as mentioned in the table.

Providing fiting & fixing chrome plated waste coupling (half thread HT and full thread FT) complete as directed and specified. (a) jaquar(i) 32mm (HT/ FT)

Proving fitting and fixing C.P. bottle trap Indian type with outlet pipe and wall flange of following size Ark Sona make for basin etc. complete as directed and specified.(a) 32mm dia

Renewing stainless steel kitchen sink of Parryware make with PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately). (A) Parryware Make(i) Single Bowl with Veg Bowl & Drain Board (400 x 200) Flat Edge- Glossy (Cat.No.C8545)

D. ELECTRICAL WORKS

Wiring for light/ fan/ call bell point with 3x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 2 mm thick 20mm dia rigid low halogen SFT PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including ceiling rose etc. complete. Short point up to 3.00 metre. Length.

Wiring for light/ fan/ call bell point with 3x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 2 mm thick 20mm dia rigid low halogen SFT PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including ceiling rose etc. complete. Medium point up to 6.00 metre. Length.

Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) cable in surface/ recessed PVC 2 mm thick rigid low halogen SFT PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system With 3 x 1.5 sq. mm. cable in 20 mm dia. rigid low halogen SFT PVC IS: 9537 Part - III conduit

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible (a) with 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. rigid low halogen SFT PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible (a) with 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. in 20 mm. dia. rigid low halogen SFT PVC IS: 9537 Part - III conduit

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible c) with 2 x 6 sq. mm. + earth continuity with 1x 4 sq. mm. in 25 mm. dia. rigid low halogen SFT PVC IS: 9537 Part - III conduit

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system. With 4 x 10 sq. mm. + earth continuity with 2x6 sq. mm. cable in 40 mm. dia. rigid low halogen SFT PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system with 2x6 sq. mm. cable in 40 mm. dia. rigid low halogen SFT PVC IS: 9537 Part - III conduit. With 4 x 16 sq. mm. + earth continuity with 2x10 sq. mm. cable in 40 mm. dia. rigid low halogen SFT PVC IS: 9537 Part - III conduit.

Supplying including and fixing of following PVC surface boxes for MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE in surface/ recessed system complete as per direction of department.1-2 module type

Supplying including and fixing of following PVC surface boxes for MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE in surface/ recessed system complete as per direction of department.3 module type

Supplying including and fixing of following PVC surface boxes for MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE in surface/ recessed system complete as per direction of department.4-5 module type

Supplying including and fixing of following PVC surface boxes for MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE in surface/ recessed system complete as per direction of department.6-8 module type

Supplying including and fixing of following PVC surface boxes for MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE in surface/ recessed system complete as per direction of department.12-16 module type

Supplying including fitting fixing of following front plate of suitable colour MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE as per direction of department.. 1 module

Supplying including fitting fixing of following front plate of suitable colour MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE as per direction of department. 2 module

Supplying including fitting fixing of following front plate of suitable colour MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE as per direction of department. 3 module

Supplying including fitting fixing of following front plate of suitable colour MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE as per direction of department. 4 module

Supplying including fitting fixing of following front plate of suitable colour MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE as per direction of department. 6 module

Supplying including fitting fixing of following front plate of suitable colour MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE as per direction of department. 8 module

Supplying including fitting fixing of following front plate of suitable colour MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE as per direction of department. 16 module

Supplying including fitting and fixing of TV co-axial outlet MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying with fitting and fixing of RJ-11 Telephone jack MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying including installation of socket outlet 6/16 Amps 3/5 pin combine shuttered complete , MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Supplying including installation of socket outlet 6 Amps 3 pin combine shuttered complete , MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Supplying with fitting fixing of 16 amp one way modular clip in switch, MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Supplying with fitting fixing of 6 amp one way modular clip in switch, MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Supplying with fitting and fixing of 25A Modular Motor Starter 2M , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting and fixing of electronic modular fan speed controller 2 - module type MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department. 100 watt electronic modular 4 step speed control 2 - module type

MCB IN-comer TPN (Horizontal DB): Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 double door surface mounting TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt.

MCB IN-comer TPN (Horizontal DB): Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 double door surface mounting TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 4 way TPN (4+12) double door. ABB, Schneider MG, legrand, Hager make)

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 8 way SPN double door

Supplying with fitting and fixing MCCB income and MCB outgoing sheet steel, phosphatised, powder painted double door IP-43 surface mounting vertical TPN MCB DB incorporated with bas-bar up to 250A, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 8way TPN (4+18) double door. ABB, Schneider MG, legrand, Hager make)

Supplying with fitting and fixing MCCB income and MCB outgoing sheet steel, phosphatised, powder painted double door IP-43 surface mounting vertical TPN MCB DB incorporated with bas-bar up to 250A, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 12 way TPN (4+36) double door . ABB, Schneider MG, legrand, Hager make)

Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 6 to 32A. C Series (Schneider MG, legrand, Hager make)

Supplying with fitting and fixing DP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 6 to 32A. B Series (ABB, Schneider MG, legrand, Hager make)

Supplying with fitting and fixing TP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.6 to 32A

Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 6 to 32A. C Series (ABB, Schneider MG, legrand, Hager make)

Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (ABB, Schneider MG, legrand, Hager make). 40A

Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (ABB, Schneider MG, legrand, Hager make)63A

Supplying with fitting and fixing Surge protector of max operating voltage 350V at 400V network for maximum discharge current 40KA, with operator indicator and draw out cartridge of Schneider or equivalent make), of the following ways complete with making necessary connection as approved, specified and directed by the deptt. Surge protection Max operating voltage 350Vintegrated type. 1P

Supplying with fitting and fixing Surge protector of max operating voltage 350V at 400V network for maximum discharge current 40KA, with operator indicator and draw out cartridge of Schneider or equivalent make), of the following ways complete with making necessary connection as approved, specified and directed by the deptt. Surge protection Max operating voltage 350Vintegrated type. 3P + N

Supplying with fitting and fixing panel mounting open execution 415V 50Hz 4P MCCB with Microprocessor Release (Ics=Icu, adjustable Over Load and Short Circuit setting, Without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 36KA (ABB, Schneider, legrand, L&T, Siemens, C&S make). 63A

Supplying with fitting and fixing panel mounting open execution 415V 50Hz 4P MCCB with Microprocessor Release (Ics=Icu, adjustable Over Load and Short Circuit setting, Without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 36KA (ABB, Schneider, legrand, L&T, Siemens, C&S make) . 100A

Supplying with fitting and fixing panel mounting open execution 415V 50Hz 4P MCCB with Microprocessor Release (Ics=Icu, adjustable Over Load and Short Circuit setting, Without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 36KA (ABB, Schneider, legrand, L&T, Siemens, C&S make) . 250A

Supplying with fitting and fixing panel mounting open execution 415V 50Hz 4P MCCB with Microprocessor Release (Ics=Icu, adjustable Over Load and Short Circuit setting, Without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 36KA (ABB, Schneider, legrand, L&T, Siemens, C&S make) . 630A

T5 LAMP WITH BOTH END connection cable, as approved by the Deptt.TOR WITH BALLAST 28 W

T5 LAMP WITH BOTH END connection cable, as approved by the Deptt.TOR WITH BALLAST 14W

Supplying including fitting fixing of following star rated A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection cable, as approved by the Deptt.s etc. as required complete and as directed by the Department [Without regulator]. (ORIENT PSPO make / Usha make/ CROMPTON make/ Havells/ ATC/ V GAURD make). Energy efficient 5-star 1200 mm sweep. ORIENT PSPO / Usha / CROMPTON / Havells/ ATC or equivalent make

Supplying with fitting and fixing panel mounting open execution 25 KA 415V 50Hz 3P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure of the following capacity complete with making necessary connection as approved by the Deptt. as specified and directed by the deptt. 25 KA 415V 50 Hz 3P MCCB .100A

Supplying ,installation, testing & commissioning of 2 pair Unarmoured Telephone Cable through existing conduit in surface/ recess system.

Supplying ,installation, testing & commissioning of 20 pair Unarmoured Telephone Cable through existing conduit in surface/ recess system.

Supply, installation testing and commissioning of following LAN networks equipments. Solid Copper Cable Cat 6, 4 pair, UTP - 305m SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..(305 mtr)

Supply, installation testing and commissioning of following LAN networks equipments.Cat 6 Keystone UTP Jack with Dust Cover-White SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supply and fixing of 25 mm dia 1.50mm to 2.00mm average wall thickness heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) on surface system including painting etc as required:

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . 300.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Sri Mrigen Sutradhar

M/s Habibar Rahman