PAINTING ON MAIN RUNWAY, PTT, MTT AND CERTAIN OTHER AIR CRAFT MOVEMENT AREAS AT AF STN KALAIKUNDA

M&L for Preparation (The surface shall be scrapped with steel wire brushes or steel scrapers. The surface shall then be broomed to remove all dust and dirt and shall be washed with clean water) of surfaces to receive painting and providing one coat water based road marking paint (boldly and solidly) as in Painting lines,dashes,arrows letters etc ., on roads, pavement and the like not exceeding 10 Cm width , white, black or Golden yellow and orange colour complete all as specified and as directed.

M&L for one coat of synthetic enamel paint on brick , concrete or plaster surface including preparation of old painted surfaces complete all as specified and as directed.

M&L for Preparation of old painted surfaces (The surface shall be scrapped with steel wire brushes or steel scrapers. The surface shall then be broomed to remove all dust and dirt and shall be washed with clean water) to receive painting and applying one coat of water based road marking paint (boldly and solidly without showing signs of brush marks) as in Painting lines,dashes,arrows letters etc ., on roads , pavement and the like surfaces, exceeding 10 Cm width ,with white, black , Golden yellow and orange colour as reqired at site complete all as specified and as directed. (a) Runway Centre line : 1150 Sqm x 6 times (once in one and half month) = 6900 Sq.m (Approx) (b) Runway Threshold and designation: 1300 Sqm x 3 times ( once in 3 month) =3900 Sq.m (Approx) (c) Runway Touch down zone: 1500 Sqm x 2 times ( once in 4 month) = 3000 Sq.m (Approx) (d) Runway Aiming point 1550 Sqm x 1 times ( Once in 6 month) = 1550 Sq.m (Approx) (e) Runway Side strip marking: 5000 Sqm x 1 times (Once in 6 month) = 5000 Sq.m (Approx) (f) PTT center line marking: 850 Sqm x 2 times (Once in 4 month) = 1700 Sq.m (Approx) (g) Bay markings (X,Y,VIP, ATC & PG ) : 2600Sqm x 4 times (Once in 2 month) = 32450 Sq.m (Approx) Total Painting Qty = 32450.00 Sqm (Approx)

M&L for preparation of old painted surfaces (The surface shall be scrapped with steel wire brushes or steel scrapers. The surface shall then be broomed to remove all dust and dirt and shall be washed with clean water) of surface to receiving paint for two coat of Acrylic emulsion paint over concrete/flexible suraces including preparation of old decorated surfaces. (General Note applicable for schedule of works item No 1 to 4 :- (i) Contractor must ensure a stock of 25% of total quantity as catererd in CA or 25% of balance quantity of the item as catered in CA (during currency of contract) at the MES provided store. If the contractor not provided said above recovery shall be made as per terms and condition of the contract as specified in particular specifications. However no 'Advance on account' against this provision as material laying at site shall be admissible (ii) The frequency of work will be done as per user/site requirement,or as directed by Engr-In-Charge. (iii) Work will be carried out on flying/ non flying days as per user requirement and contractor have to provide barricading on working site as per direction of Engineer-in-Charge. No flying will be entertained due to any loss of working hours (iv) Being operational nature of work, it is imperative for the contractor to address the work as directed by Engineer-in-Charge within 24 hours after placing order by the Engineer-in-Charge on site order book or through any other/ digital mode as and when required basis. No claim like shortage of materials and shortage of labours whatsoever will be admissible and a recovery of Rs. 2000/- per day per site not addressed will be affected from the payment due to the contractor after 24 hours of the instructions passed by Engineer-in-Charge in site order book or any other digital modes.

M&L for sure Bond Tape 100mm width and 2 mm thick for crack surfaces of Runway( Flexible and Rigid portion),PTT,MTT & Dispersals by preparation of surfaces by electric brushes, air blower to clean the crack(joint )and paste the sure bond tape on crack surfaces and rolling with hand held wooden/Rubber roller with force all as specified and as directed by Engr-in-charge.

M&L for sure Bond Tape 75mm width and 2 mm thick for crack surfaces of Runway( Flexible and Rigid portion),PTT,MTT & Dispersals by preparation of surfaces by electric brushes, air blower to clean the crack(joint )and paste the sure bond tape on crack surfaces and rolling with hand held wooden/Rubber roller with force all as specified and as directed by Engr-in-charge.