Repair/Replacement of Pumping System, Switchgear, Pipe Line and Control Valves at Distribution Area Under GE (Utilities) Udhmapur

Amount

Decoupling, disconnecting suction line and discharge line taking down from foundation, dismounting from base channels strip opening all parts, derusting, cleaning, overhualing comprising of repairs/replacement of unserviceable parts of pump sets and taking to workshop (if reqd) for repairs. Reassembling of pump set mounting and fixing on base channel, recoupling of suction & discharge line realignment commissioning and testing in respect of centrifugal/multistage pump of capacity 50 to 60 HP, complete all as specified and directed by Engineer-in-charge. Note :(i) Loading/unloading & transportation charges shall be deemed included in the quoted rates. (ii) S&F of parts shall be measured and paid separately under respective item of sch A.

All as per ser item No 01.00 here-in-before but capacity 30 to 40 HP, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 01.00 here-in-before but capacity 15 to 20 HP, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 01.00 here-in-before but capacity 7.5 to 10 HP, complete all as specified and directed by Engineer-in-charge.

S&F New parts for single/multistage pumps of capacity 50 to 60 HP as per manufacturer's composition of existing make of pump as below, complete all as specified and directed by Engineer-in-charge.

Pump impeller made of CI Make : Kirloskar/Wilo Mather Platt or equivalent make as approved be GE.

Pump shaft stainless steel shaft complete with check nut and keys

Tyre coupling/star coupling

Star /Tyre coupler made of steel

Gland cup

Shaft sleeves

Bearing housing

Casing housing

S&F New parts for single/multistage pump of capacity 30 to 40 HP as per manufacturer's composition of existing make of pump as below, complete all as specified and directed by Engineer-in-charge :-

Pump impeller made of CI. Make : Kirloskar/Wilo Mather Platt or equivalent make as approved be GE.

Pump shaft stainless steel shaft complete with check nut and keys

Tyre coupling/star coupling

Star coupler made of steel

Gland cup

Shaft sleeves

Bearing housing

Casing housing

S&F New parts for single/multistage pump of capacity 15 to 20 HP as per manufacturer's composition of existing make of pump as below, complete all as specified and directed by Engineer-in-charge :-

Pump impeller made of CI. Make : Kirloskar/Wilo Mather Platt or equivalent make as approved be GE.

Pump shaft stainless steel shaft complete with check nut and keys

Tyre coupling/star coupling

Star /Tyre coupler made of steel

Gland cup

Shaft sleeves

Bearing housing

Casing housing

S&F New parts for single/multistage pump of capacity 7.5 to 10 HP as per manufacturer's composition of existing make of pump as below, complete all as specified and directed by Engineer-in-charge :-

Pump impeller made of CI. Make : Kirloskar/Wilo Mather Platt or equivalent make as approved be GE.

Pump shaft stainless steel shaft complete with check nut and keys

Tyre coupling/star coupling

Star /Tyre coupler made of steel

Gland cup

Shaft sleeves

Bearing housing

Casing housing

Pump seal

Lath/Mchining works of any type at workshop required for balancing of impller/for fixing of new parts to existing shfts required for proper setting and smooth functioning to achieve desired discharge of the pump for 50 to 60 HP pump, complete all as specified and as directed by Engr-in-charge.

All as per srl item No. 9.00 here-in-before but capacity of 30 to 40 HP motor, complete all as specified and directed by Engineer-in-charge.

All as per srl item No.9.00 here-in-before but capacity of 15 to 20 HP motor, complete all as specified and directed by Engineer-in-charge.

All as per srl item No.9.00 here-in-before but capacity of 7.5 to 10 HP motor, complete all as specified and directed by Engineer-in-charge.

Disconnecting electric connection of 50 to 60 HP motor, removing the UNSV motor from existing place by unscrewing the foundation bolts and nuts decoupling from the pump, setting aside and transporting to workshop for repairs including dismantling the motor,cutting/taking out burnt winding of stator, rotor, cleaning the slots, transporting back after repair/winding & re-assembling the same, complete all as specified and directed by Engineer-in-charge. Note: (a) Rewinding of motor will be measured and paid separately under relevent item. (b) The rates quoted shall be deemed to include the cost of loading/unloading, transportation, grease, nuts, bolts and washers of any size and shape as required at site and refixing of serviceable motor duly functional and testing complete at its existing location/position, complete all as specified and directed by Engineer-in-charge.

All as per srl item No. 13.00 here-in-before but capacity 30 to 40 HP motor, complete all as specified and directed by Engineer-in-charge.

All as per srl item No. 13.00 here-in-before but capacity of 15 to 20 HP motor, complete all as specified and directed by Engineer-in-charge.

All as per srl item No. 13.00 here-in-before but capacity of of 7.5 to 10 HP motor, complete all as specified and directed by Engineer-in-charge.

Removing the burnt out winding from the rotor and stator, cleaning the slots, providing high quality of class'B' paper insulation inside the slots, rewinding the motor of capacity 60/50/40/30/20/15/12/10/7.5 HP with super enamel copper wire of same size and guage as per existing rapping up with high quality cotton tape and varnising with super quality oil including drying upto desired temperature and desired time, complete all as specified and directed by Engineer-in-charge. Note:- Cost of labour for winding deemed to be included in the rate quoted. Make : Atlas/Devi Dayal or equivalent make.

Supply and fixing in repair of 2 to 3 HP pumpset (including motor) by taking out from foundation, dismounting from base channels, strip opening all parts, derusting, cleaning, overhualing, etc for complete repair/ replacement of spare parts such as impeller, shaft, winding, bearings, coupling, body, etc and after repair/ replacement, reassembling of pumpset mounting and fixing on base channel, recoupling of suction & discharge line, realignment, commissioning and testing, complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair of 0.5 to 1 HP pumpset (including motor) by taking out from foundation, dismounting from base channels, strip opening all parts, derusting, cleaning, overhualing, etc for complete repair/ replacement of spare parts such as impeller, shaft, winding, bearings, coupling, body, etc and after repair/ replacement, reassembling of pumpset mounting and fixing on base channel, recoupling of suction & discharge line, realignment, commissioning and testing, complete all as specified and directed by Engr-in-Charge.

M&L for repair of booster pressure pump set of cap 0.25 HP to 1 HP by taking out from foundation, dismounting from base channels, strip opening all parts, derusting, cleaning, overhualing, etc for complete repair, reassembling of pumpset mounting and fixing on base channel, recoupling of suction & discharge line, realignment, commissioning and testing, complete all as specified and directed by Engr-in-Charge.

Supply and fixing of relay switch for booster pressure pump of capacity 0.25 HP to 1 HP pumpset, complete all as specified and directed by Engr-in-Charge.

M&L for dismantling following spare parts of submersible pump and motor of cap 1 to 5 HP and separating the unserviceable parts cleaning the serviceable parts, re-metalling machinery polishing and re-assembling including replacement of old parts and necessary painting, complete all as specified and directed by Engineer-in-charge. Note:- Old unserviceable parts replaced will be measured and paid separately.

M&L for Impeller for submersible pump set and motor, complete all as specified and directed by Engineer-in-charge.

M&L for Bush for impeller for submersible pump set and motor, complete all as specified and directed by Engineer-In-Charge.

S&F of Pump bearing No. 6307 C3, complete all as specified and directed by Engineer-in-charge. Make:-SKF/NBC/NRB or equivalent make

S&F of Pump bearing No. 6308 2RS1/C3, complete all as specified and directed by Engineer-in-charge. Make:-SKF/NBC/NRB or equivalent make

S&F of Motor bearing No. 6311, complete all as specified and directed by Engineer-in-charge. Make:-SKF/NBC/NRB or equivalent make

S&F of Motor bearing No. NU411M/7311, complete all as specified and directed by Engineer-in-charge. Make:-SKF/NBC/NRB or equivalent make

S&F in replacement of ON load change over switch 320 Amps, 415 volts 4 pole inculding taking down the old existing change over switch, complete all as specified and directed by Engineer-in-charge. Make : Havells/L&T/ABB

All as per ser item No 29.00 here-in-before but of size 200 Amps, complete all as specified and directed by Engineer-in-charge. Make : Havells/L&T/ABB

All as per ser item No 29.00 here-in-before but of size 100 Amps, complete all as specified and directed by Engineer-in-charge. Make : Havells/L&T/ABB

S&F in replacement of OFF load change over switch 320 Amps, 415 volts 4 pole with stainless steel enclosure inculding taking down the old existing change over switch, complete all as specified and directed by Engineer-in-charge. Make : Havells/L&T/ABB

All as per ser item No 32.00 here-in-before but of size 200 Amps/160 Amps, complete all as specified and directed by Engineer-in-charge. Make : Havells/L&T/ABB

All as per ser item No 32.00 here-in-before but of size 100 Amps, complete all as specified and directed by Engineer-in-charge. Make : Havells/L&T/ABB

All as per ser item No 32.00 here-in-before but of size 63 Amps, complete all as specified and directed by Engineer-in-charge. Make : Havells/L&T/ABB

S&F in replacement of load line MCCB 320/350 Amps 4 pole 415 volts with adjustable thermal and fixed magnetic setting of breaking capacity 35/36 KA,Ics=100% Icu confirming to IEC-60947-2 including taking down the old existing MCCB, complete all as specified and directed by Engineer-in-charge. Make : L&T/LEGRAND/ABB/SIEMENS

All as per ser item No 36.00 here-in-before but of size 200 Amps, complete all as specified and directed by Engineer-in-charge. Make : L&T/LEGRAND/ABB/SIEMENS

All as per ser item No 36.00 here-in-before but of size 160 Amps, complete all as specified and directed by Engineer-in-charge. Make : L&T/LEGRAND/ABB/SIEMENS

All as per ser item No 36.00 here-in-before but of size 125 Amps, complete all as specified and directed by Engineer-in-charge. Make : L&T/LEGRAND/ABB/SIEMENS

All as per ser item No 36.00 here-in-before but of size 100 Amps, complete all as specified and directed by Engineer-in-charge. Make : L&T/LEGRAND/ABB/SIEMENS

All as per ser item No 36.00 here-in-before but of size 63 Amps, complete all as specified and directed by Engineer-in-charge. Make : L&T/LEGRAND/ABB/SIEMENS

S&F in replacement of power contactor 3 pole with AC coil AC-3 duty rating at 415 Volts 50 Hz, frame size1 suitable for 60 HP centrifugal pump set as per Havells cat part No. IHPHA100400*, complete all as specified and directed by Engineer-in-charge.

M&L in replacement of PVC insulated heavy duty industrial cables single core copper conductor(flexible) PVC insulated cable 1100 volt nominal area of conductor 50 sqmm inculding taking down existing old unserviceable cable of complete all as specified and directed by Engineer-in-charge.

All as per ser item No. 43.00 here-in-before but of size 25 sqmm, complete all as specified and directed by Engineer-in-charge.

All as per ser item No. 43.00 here-in-before but of size 16 sqmm, complete all as specified and directed by Engineer-in-charge.

M&L for copper thimble suitable for 50 Sqmm single core copper cable including taking down the existing unserviceable one, complete all as specified and directed by Engineer-in-charge.

All as per item No. 46.00 here-in-before but of size 25 sqmm, complete all as specified and directed by Engineer-in-charge.

All as per item No. 46.00 here-in-before but of size 16 sqmm, complete all as specified and directed by Engineer-in-charge.

M&L for aluminium thimble of 150 sqmm size for cables, complete all as specified and directed by Engineer-in-charge.

M&L for aluminium thimble of 95 sqmm size for cables, complete all as specified and directed by Engineer-in-charge.

S&F capacitor upto 40 mfd for motor, complete all as specified and directed by Engineer-in-charge.

S&F in replacement of DOL starter in sheet steel enclosure single phase 220 volts, 50 Hz for motor of capacity 5 HP as per Havells cat part No. IHHDOLLA*E, complete all as specified and directed by Engineer-in-charge. Make:-Havells/Legrand/L&T

Supply and laying DWC (Double wall corruguated) pipe 40/32 mm conforming to IS-14930/ IS-16205 for protection of earth strip/cable including necessary snap fit coupler reqd for fixing, complete all as specified and directed by Engineer-in-charge.

Supply and laying DWC (Double wall corruguated) pipe 50/41 mm conforming to IS-14930/ IS-16205 for protection of earth strip/cable including necessary snap fit coupler reqd for fixing, complete all as specified and directed by Engineer-in-charge.

Supply and laying DWC (Double wall corruguated) pipe 75/63 mm conforming to IS-14930/ IS-16205 for protection of earth strip/cable including necessary snap fit coupler reqd for fixing, complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement of terminal boxes suitable for 60/50 HP motor as per existing specification including taking down the old existing terminal box, complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement of terminal boxes suitable for 40/30/20 HP motor as per existing specification including taking down the old existing terminal box, complete all as specified and directed by Engineer-in-charge.

M & L for painting of header/pump and motor, frame, pipe line including surface preparation by scrapping with emery paper and painting two coats of synthetic enamel paint over one coat of red oxide primer of existing colour of approved make to the satisfaction of Engr in Charge, complete all as specified and directed by Engineer-in-charge.

M&L for writing with brush about the machinery installed in different instalations such as Cap, discharge,MES No,Year of installation and head of the machinery on the wall in front of the pump motor with black paint including removing the existing paint with help of grinder, complete all as specified and directed by Engineer-in-charge.

S&F in replacement of gland packing type 3 of size 8 mm made of asbestos grip with silicon, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 60.00 here-in- before but of size 10 mm, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 60.00 here-in- before but of size 16 mm, complete all as specified and directed by Engineer-in-charge.

Supply and laying in replacement of synthetic rubber insulated mats 10 mm thick for insulation purpose suitable for electrical shock safety of sizes 2 m x 1.2 m, complete all as specified and directed by Engineer-in-charge.

S&F in replacement of MS stud bolts of existing size suitable for pumps and motors of various capacity installed at installations, complete all as specified and directed by Engineer-in-charge.

S&F in replacement of grouting nuts and bolts of existing size suitable for pumps and motors foundation of various capacity installed at installations, complete all as specified and directed by Engineer-in-charge.

M&L for cement concrete type B-2, 1:2:4 (40mm graded aggregate) as in sub base filling and mass concrete, complete all as specified and directed by Engineer-in-charge.

M&L for cement concrete in foundations, type E-2, 1:5:10 (40mm graded aggregate) as in filling and mass concrete, complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repacement of Cast iron Foot valve Flanged with strainer of 150 mm dia including all types of fittings conforming to IS specification, complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repacement of Cast iron Foot valve Flanged with strainer of 100 mm dia including all types of fittings conforming to IS specification, complete all as specified and directed by Engineer-in-charge.

Supply only lithium base grease AP3 in 20 Kg pack suitable for application to ball bearing with operating temperature 30 to 120 degree celsius drop point 174 degree celsius, colour light fawn, complete all as specified and directed by Engineer-in-charge.

Supply only cotton waste coloured Grade "A' for cleaning rags in 25 Kgs bag, complete all as specified and directed by Engineer-in-charge.

M&L for writing of "SAVE WATER" in Tri-colour on Overhead Tank / Sump with blue colour on white backround as per existing, complete all as specified and directed by Engineer-in-charge.

Supply only Chlorine testing kit to check the chlorine at installations, complete all as specified and directed by Engineer-in-charge.

Supply and laying, jointing and testing of XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 95 sqmm 3.5 core laid in trenches,ducts, pipes, complete all as specified and directed by Engineer-in-charge.

Supply, installation, commisioning and testing of LT Panel board indoor type mounted on rigid angle iron frame 60 CM long legs made out of 50x50x6mm angle, dust and vermin proof, factory made, fabricated out of 2 mm thick CRCA sheet suitable for 3 phase 415 V, 50 Hz AC supply busbar chamber with copper busbar for 3 phase and neutral for wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators 01 set, common earth busbar of GI strip 32 x6 at bottom with panel board at 2 earth terminals, cable glands with independent plates at bottom for each outgoing and incoming cables and complete panel board painted with powder coating in siemens Grey colour and fabricated with double door system locking arrangement embedded in PCC M15, type B1 complete. The panel must be designed and verified IS/IEC 61439-01 and 02 with complete test certificate for confirmation all as approved and comprising as under, complete all as specified and directed by Engineer-in-charge:-

Earthing of machinery/equipment Installed at power house/substation with galvanised steel earth plate electrode 600 mm × 600 mm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised iron strip 32× 6mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion, complete all as specified and directed by Engineer-in-charge.

Opening, maintenance and general servicing of Servo voltage stablizers of different makes of 100 KVA including removal of sludge from disserstate coils, buck boost transformers, tightening of all nut bolts, cleaning of stablizers coils, checking and servicing of servo mechanism, gear synchronising system, automatic voltage regulator circuits and other allied electrical components, complete all as specified and directed by Engr-in-charge. Note : Rate quoted by contractor is inclusive of following items:- (a) Servo motor with RC network having torque upto 10 kg/cm (b) Electronic cntrol card for automatic voltage regulation (c)Transformer oil -35 ltrs (d) Voltmeter 0-500 volt capacity (e) Ammeter CT Operated (f) Items like carbon bush, push buttons auto/manual/micro press switch, indicator lamps, etc

Preparation of plinth of size 5 x 3 x 0.9 mtr for captive power plant installed at MT pump house including necessary excavation, returning, removal of soil, PCC 1:4:8, RCC M25, reinforcement, complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth,foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. and taking out/laying of pipe lines of soft/loose soil. Complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers, each layer not exceeding 25cm thick after pipes have been laid and tested, complete all as specified and directed by Engineer-in-charge.

Removing excavated material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as specified and directed by Engineer-in-charge.

Taking up or down old unseviceable GI pipe of size 150 mm dia including all fittings, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 82.00 here-in-before but of 100 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 82.00 here-in-before but of 80 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 82.00 here-in-before but of 50 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 82.00 here-in-before but of 40 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 82.00 here-in-before but of 25 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 82.00 here-in-before but of 20 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 82.00 here-in-before but of 15 mm dia, complete all as specified and directed by Engineer-in-charge.

Supply & fixing GI pipes of size 150 mm dia, medium grade, galvanized with all fitting such as bends, tees, nipples, union and sockets, clamps etc laid in trenches, under floor/walls etc, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 90.00 here-in-before but of 100 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 90.00 here-in-before but of 80 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 90.00 here-in-before but of 50 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 90.00 here-in-before but of 40 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 90.00 here-in-before but of 25 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 90.00 here-in-before but of 20 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 90.00 here-in-before but of 15 mm dia, complete all as specified and directed by Engineer-in-charge.

Refixing GI/CI pipe obtained from Item No. 82.00 above and connections in new or old position (walls, trenches, ceiling and floors etc) of size 150 mm dia complete including main branch connections, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 98.00 here-in-before but of 100 mm dia obtained from item No. 83.00, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 98.00 here-in-before but of 80 mm dia obtained from item No. 84.00, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 98.00 here-in-before but of 50 mm dia obtained from item No. 85.00, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 98.00 here-in-before but of 40 mm dia obtained from item No. 86.00, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 98.00 here-in-before but of 25 mm dia obtained from item No. 87.00, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 98.00 here-in-before but of 20 mm dia obtained from item No. 88.00, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 98.00 here-in-before but of 15 mm dia obtained from item No. 89.00, complete all as specified and directed by Engineer-in-charge.

Supply and fix in replacement cast iron sluice valve suitable of size 300 mm (PN 1.6) ISI Marked with iron wheel head both end flanged, non rising type and jointing with the rubber or fibre board gasket complete with and including required nos size of nuts, bolts and washers including taking down the old existing, complete all as specified and directed by Engr-in-Charge.

All as per ser item No 106.00 here-in-before but of size 200 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 106.00 here-in-before but of size 150 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 106.00 here-in-before but of size 100 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 106.00 here-in-before but of size 80 mm dia, complete all as specified and directed by Engineer-in-charge.

Supply and fix in replacement of cast iron non return valve suitable for 150 mm bore pipe heavy duty both end flanged of pressure rating PN 1.6 and jointing with the rubber or fibre board gasket complete with and including required nos size of nuts, bolts and washers including taking down the old existing, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 111.00 here-in-before but of size 100 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 111.00 here-in-before but of size 80 mm dia, complete all as specified and directed by Engineer-in-charge.

Supply and fix Foot Valve of size 50 mm dia, complete all as specified and directed by Engineer-in-charge.

Supply and fix Foot Valve of size 40 mm dia, complete all as specified and directed by Engineer-in-charge.

Supply and fix in replacement of cast iron air release valve with two air outlets of size 100 mm dia including all jointing materials like high pressure rubber gasket nuts, bolts, washers with arrangement for fixing, including taking down complete,complete all as specified and directed by Engr-in-Charge.

All as per ser item 116.00 here-in-before but of size 80 mm dia, complete all as specified and directed by Engineer-in-charge.

Repair to old sluice valve of size 300 mm dia for check nut, spindle, refacing, regrinding & refixing at its original location including cleaning, repacking stuffing box of sluice valve & spindle including fixing & testing, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 118.00 here-in-before but of 200 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 118.00 here-in-before but of 150 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 118.00 here-in-before but of 100 mm dia, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 118.00 here-in-before but of 80 mm dia, complete all as specified and directed by Engineer-in-charge.

M&L for repair to leaking run lead joints in CI/DI spigot and socket end pipe line of 100 to 150mm bore by providing new lead ,using good quality spun yarn, including necessary excavation, returning filling in trenches in any type of soil,bailing out water, and at any depth, complete all as specified and directed by Engr-in-Charge. Note:- (i) Contractor fully responsible for necessory excavation for jointing work required T&P equipment, mechanical excavation work and man power at site requirement with making good disturbed surfaces of road/wall/floor etc and matching with existing surface included quoted rate. (ii) Required extra fittings/pipe will be measured and paid separately.

Supply and fixing in replacement of LED Multi colour (colour changer) under water lights of capacity 18 wt 12 volt DC with IP 68 Protection, complete all as specified and directed by Engineer-in-charge.

Supply and fixing control module box included MCB's for controlling 18 wt LED lights, complete all as specified and directed by Engineer-in-charge.

M&L for repair to leaking GI pipe line of size 50 mm to 80 mm bore by providing necessary fitting such as socket, Tee, Elbow,etc including necessary excavation, returning filling in trenches in any type of soil,bailing out water, and any depth, complete all as specified and directed by Engr-in-Charge. Note:- (i) Contractor fully responsible for necessory excavation for jointing work required T&P equipment, mechanical excavation work and man power at site requirement with making good disturbed surfaces of road/wall/floor etc and matching with existing surface included quoted rate. (ii) Required extra pipe will be measured and paid separately.

All as per ser item No 126.00 here-in-before but of size 20 mm to 40 mm bore pipe, complete all as specified and directed by Engineer-in-charge.

Material and labour for repair to leaking flanged/circular welding joints of 100 to 200 mm bore MS/GI pipe line by providing rubber or fiber board gasket, new flanges if required at site, nut bolts, washers and welding works where required etc, including necessary excavation, returning filling in trenches in any type of soil, bailing out water, and any depth, complete all as specified and directed by Engr-in-Charge. Note:- (i) Contractor fully responsible for necessory excavation for jointing work required T&P equipment, mechanical excavation work and man power at site requirement with making good disturbed surfaces of road/wall/floor etc and matching with existing surface included quoted rate. (ii) Required extra pipe will be measured and paid separately.

All as per ser item No 128.00 here-in-before but of dia 250 to 300 mm bore pipe, complete all as specified and directed by Engineer-in-charge.

M&L for cutting of existing road for crossing of MS/DI/CI/GI pipes for laying of any size pipes including necessary exacavation and earth work including repairing the same as per existing, complete all as specified and directed by Engr-in-Charge.

M&L PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) cement concrete in as in foundation filling of pole & stay, complete all as specified and directed by Engineer-in-charge.

M&L for Premix ready mix road repair patching compound for instant road repair manufactured with a blend of bitumen, aggregates and high grade polymer to ensure immediate bonding with existing surface available in bag of 25 Kg, complete all as specified and directed by Engineer-in-charge.

Supply of Copper Sulphate for swimming pool water cleaning and colouring, complete all as specified and directed by Engineer-in-charge.

Supply and fix in replacement of LED underwater lights of cap not less than 34 watt and 12 V DC supply, IP-68 protection of external body size 225 mm dia with independent control gear, complete all as specified and directed by Engineer-in-charge.

Supply and fix in replacement of driver of LED underwater lights of cap 34 watt and 12 V DC supply, protection of external body size 225 mm dia with independent control gear, complete all as specified and directed by Engineer-in-charge.

Supply and fix water proof fountain light of capacity 10 watt having warm light output, complete all as specified and directed by Engineer-in-charge.

Supply and fixing the nipple brass nozzle as per sample including removal of existing unsv one, complete all as specified and directed by Engineer-in-charge.

Supply & Laying multicore PVC insulated and FR-LHS PVC round sheatehed, copper conductor(flexible) industrial cable 1100 volt grade confirming to Is 694 , 1.5 sqmm 1 core including suitable size PVC conduit laid, complete all as specified and dirwcted by Engr in Charge.

All as per ser item No 138.00 here-in-before but of size 2.5 sqmm 1 core, complete all as specified and directed by Engineer-in-charge.

Supply & laying of flexible pipe of 15/20 mm dia used for wiring purpose, complete all as specified and directed by Engineer-in-charge.

Supply and fix in replacement of PVC Butterfly valve of of size 140 mm dia PN 16, complete all as specified and directed by Engineer-in-charge.

Supply and fix in replacement of PVC Foot valve of of size 110 mm dia PN 16, complete all as specified and directed by Engineer-in-charge.

Repair to leakage of 110 to 160 mm PVC pipe including all necessary fitting such as Tee, Socket, jointing material etc, complete all as specified and directed by Engr-in-Charge.

Supply & fixing PVC pipe of size 110 mm dia class 3 (as per existing) including all necessary fitting such as bends, Socket, jointing material etc, complete all as specified and directed by Engineer-in-charge.

Supply & fixing PVC pipe of size 140 mm dia class 3 (as per existing) including all necessary fitting such as bends, Socket, jointing material etc, complete all as specified and directed by Engr-in-Charge.

Supply & fixing PVC pipe of size 160 mm dia class 3 (as per existing) including all necessary fitting such as bends, Socket, jointing material etc, complete all as specified and directed by Engr-in-Charge.

S&F cast iron fittings for spigot and socket ends for pressure pipe for water mains such as bends, tapers, tee pieces single branch, cross collar, caps and plugs suitable for upto 150 mm bore, all specifications as per IS-1538 (Pt-1 to 23)-1976 and all as specified and directed by Engr-in-Charge.

Supply fabrication and fixing MS joints like Flanged, bends, Tee, Tapers, collars, elbow, tail piece (any type) caps, plugs for 80 mm to 300 mm bore pipe, complete all as specified and directed by Engineer-in-charge.

S&F of Gun metal, globe or gate valves, 80mm dia , heavy duty, with iron wheel head, screwed both ends (ISI marked), complete all as specified & directed by Engr-in-Charge.

S&F of Gun-metal, globe or gate valves, 50 mm dia , heavy duty, with iron wheel head, screwed both ends (ISI marked), complete all as specified & directed by Engr-in-Charge.

All as per ser item No 150.00 above here-in-before but upto 40 mm bore, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 150.00 above here-in-before but upto 25 mm bore, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 150.00 above here-in-before but upto 20 mm bore, complete all as specified and directed by Engineer-in-charge.

All as per ser item No 150.00 above here-in-before but upto 15 mm bore, complete all as specified and directed by Engineer-in-charge.

Supply and fixing GI fittings medium grade ISI marked including complete all as required at site and complete all as specified and directed by Engineer-in-charge.

Elbow 15mm

Elbow 20mm

Elbow 25mm

Elbow 40mm

Elbow 50mm

Elbow 80mm

Socket 15mm

Socket 20mm

Socket 25mm

Socket 40mm

Socket 50mm

Socket 80mm

Union 15mm

Union 20mm

Union 25mm

Union 40mm

Union 50mm

Union 80mm

Elbow reducer 20 x 15mm

Elbow reducer 25 x 20mm

Elbow reducer 40 x 25mm

Socket reducer 25x20mm

Socket reducer 40x25mm

Socket reducer 40x20mm

Socket reducer 50x25mm

Nipple 15 x50mm

Nipple 15 x100mm

Nipple 20 x50mm

Nipple 20 x100mm

Nipple 25 x 50mm

Nipple 25 x 100mm

Nipple 40 x 50mm

Nipple 40 x 100mm

Nipple 50 x 50mm

Nipple 50 x 100mm

Tee 15mm

Tee 20mm

Tee 25mm

Tee 20x15mm

Tee 25x20mm

Tee 40x15mm

Tee 40x20mm

Tee 40x25mm

Tee 50x25mm

Dead plug 15mm

Dead plug 20mm

Dead plug 25mm

Dead plug 40mm

Dead plug 50mm

Lead wool

Carry out servicing from authorized rep of service engineer of the manufacture of industrial RO+U.V. water purifier system consisting of fiber reinforced polymer vessel with treatment media like FBM AFM MGS, ACM, CPM etc of capacity of 1000 LPH, complete all as specified and directed by Engineer-in-charge.

Attending complaints for rectification of fault in RO I Panel (Control panel of industrial RO+U.V. water purifier system consisting of fiber reinforced polymer vessel with treatment media like FBM AFM MGS, ACM, CPM etc of capacity of 1000 LPH including replacement worn out relay, cable, fuse, diode etc, complete all as specified and directed by Engineer-in-charge.

Supply and fix food grade activated carbon for RO Plant capacity 1000 LPH, complete all as specified and directed by Engineer-in-charge.

Supply and fix and testing food grade softner Resin 220 Na for RO plant of capacity of 1000 LPH, complete all as specified and directed by Engineer-in-charge.

Supply and fix and testing 20" Jumbo Span candle for RO Plant of capacity of 1000 LPH, complete all as specified and directed by Engineer-in-charge. Note: Model should be compatible for existing of RO Plant

Supply and fix and testing RO membrane 40x40 for RO Plant of capacity 1000 LPH, complete all as specified and directed by Engineer-in-charge. Note: Model should be compatible for existing of RO Plant

Supply and fix and filing clean wash sand for RO Plant of capacity 1000 LPH, complete all as specified and directed by Engineer-in-charge.

Supply and filling (NaCL) common salt for RO Plant of capacity 1000 LPH, complete all as specified and directed by Engineer-in-charge.

FANGALIA TRADERS (BID ID -3191116)