SPECIAL REPAIRS TO MEDICAL INSPECTION ROOM BLDG NO.P 91 AT DMRL AND CERTAIN OTHER SANCTIONED WORKS UNDER GE I RND KANCHANBAGH HYDERABAD.

Amount

Taking down existing roof treatment of any description, any position with bituminous felt including plaster/loose concrete and removing rubbish to a distance exceeding 500m but not exceeding 1000m and roughening the surfaces of old concrete by picking, scraping, cleaning and washing down with water to remove all dust etc complete specified and directed

M & L cutting out cracks to V section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and as directed

M&L providing plain cement concrete type B-0, 1:2:4 (12.5mm graded stone aggregate) in roof padding, kerb or mud stop, rounded or chamfered on edges to maintain proper slope on roof slab complete all as specified

M&L for brushing neat cement slurry with 3 Kg of cement per Sqm over the RCC slab and sides complete all as directed by Engr-in-Chrage.

M&L for rendering 10mm in CM 1:3 over concrete surfaces on RCC roof slab and parapets mixed with WPC @ 3% by weight of cement shall be carried out complete all as specified and directed by Engr-in-Charge. Note : WPC will be measured and paid separately.

Supply only integral water proofing compound

M&L water proofing treatment with polymeric standard membrane of weight not less than 3.5 kg per sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150gms/sqm) laid over primed surface by forced application complete. Shall be fused uniformly by LPG torch flame on horizontal/vertical/slope surface on roof complete all as specified and directed by Engr-in-Charge. Water proof treatment consist of as under: - (i) Applying one coat of bitumous primer conforming to IS 3384 @ 0.3 ltrs per sqm (ii) Laying APP based memberane as specified thickness and weight. (iii) Applying one coat of bitumen grade 85/25 @1.20Kg per sqm.

M&L for cutting grooves in brick wall 70mm wide and 65mm deep and sweeping horizontal face of groove with cement mortar (1:3) and making good in CM 1:3 after inserting membrane into the groove complete all as specified and directed by Engr-in-Charge.

M&L for preparation of surfaces of any description, over 10cm in width or girth otherwise described and appplying two coat of aluminium paint @100ml per sqm over APP membrane sheet complete all as specified and directed by Engr-in-Charge.

Taking down existing unserviceable false ceiling of any description, thick ness and any position including channels, sections angles etc, complete all as directed.

M&L aluminium anodised snap grid frame work for false ceiling grid size 605 x 605mm with runners aluminium anodised main Tee of section 35 x 35x 1.5mm thck, cross Tee of section 25 x 25 x 1.5mm thick and aluminium anodised angle of size 25mm x 1.5mm thick section fixed along side of wall including hanging from ceiling with 6mm dia GI ( upto 1200 mm length ) adjustable level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long etc in repairs complete all as specified

S&F hangers 6mm dia GI ( upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fastners 12.5mm dia 40mm long complete all as specified

M&L for providing 12mm thick Gypsum board ( 600 x 600mm) in ceiling fixed with screw as per manufacturers instructions

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to stores and rubbish off the premises. all as directed.

S&F Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in cement mortar 1:4 complete.

All as per item No.15 above but on vertical surfaces such as skirting (skirting is to be flush with wall ) and 10mm thick rendering in CM 1:3 on fair faces of brick / concrete surfaces as backing coat for tiles complete all as directed

S&F vitrified tiles 10mm thick any shade (Square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc joint free set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 15mm thick screed bed in CM (1:4) all as specified and as directed by Eng-in-charge.

All as per item No 17 above but on vertical surfaces such as skirting (skirting is to be flush with wall ) and 10mm thick rendering in CM 1:3 on fair faces of brick / concrete surfaces as backing coat for tiles complete all as directed by Engr -in- Charge

S&F glazed ceramic coloured tiles including borders in vertical surfaces 300x200x7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles over and including 10mm thick rendering in CM 1:4 as backing layer complete all as specified and directed.

S&F Glazed coloured ceramic tiles in vertical surface 450 x 300x 7 mm thick, set and jointed in neat cement slurry and pointed in white or cloured cement 10mm thick backing coat CM of 1:3 complete all as specified and as directed.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing white cement (1:2) using marble dust with admixture of pigment to match the shade of granite including cutting grooves and nosing over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engr-in-Charge.

Demolition stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in cement mortar all as directed.

M&L for rectangular aluminium hollow section of size 101.6 x 44x2mm thick as in partition ( including fixing with nut and bolt in floor and wall by drilling holes), powder coated of approved colour for both vertical and horizontal member including 5.5mm thick glass, 12mm thick particle board prelaminated on both side, aluminium legs, aluminium glazing channel, rubber beading as required complete all as directed.

All as per item No 23 above but as in door, powder coated, approved colour, including 5.5mm thick glass, 12mm thick particle board prelaminted on both side, rubber beading, aluminium glazing channels, two Nos handle, three Nos extruded aluminium hinges 100mm long, two Nos 200mm aluminium anodised, barrel tower bolts of extruded section, one floor door stopper 150mm of aluminium alloy body, 100mm size brass mortice lock, 4 levers with two keys and floor door spring as required for door complete all as specified and directed.

S & F Powder coated aluminium sliding window of standard sections, 2 mm thick (Jindal code No 21516 for bottom track, code No.21517 for top & sides, 21514 for interlock, code No.21515 for shutter side, top bottom) or equivalent make as approved by GE, powder coated of approved colour incluidng aluminium grill, 4mm thick sheet glass, aluminium handle, bearings, sliding rails, rubber beading, suncontrol film including taking down existing unserviceable one, complete all as specified and directed

S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, properly rolled on glass panes without any wrinkle including removal of existing unserviceable film on windows/doors complete all as directed by Engr-in-Charge. Make : GARWARE OR EQUIVALENT

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises, removal and depositing serviceable materials where directed and leaving the work clear of any plastering.

M & L for rendering 15 mm thick on stone masonary surface or surface other than fair faces of brick work in CM 1:4 finished even and smooth without using extra cement

M & L for rendering 15 mm thick on stone masonary surface or surface other than fair faces of brick work or on one side of lathing in CM 1:6 finished even and smooth without using extra cement

M & L rendering 10 mm thick on brick work or concrete surfaces in ceiling in CM 1:3 finished finished even and smooth without using extra cement

M&L for Preparing newly plastered surfaces and applying two coats of distemper oil emulsion including priming plastered and other surfaces with alkali resistant priming paint on surfaces of walls over a coat of wallputty to make surfaces smooth.

M&L for Complete removal of existing treatment and applying two coats of distemper oil emulsion including priming plastered and other surfaces with alkali resistant priming paint on surfaces of walls over a coat of wallputty to make surfaces smooth.

M&L for complete removal of existing treatment from external surfaces of walls/ ceiling, washing with water and applying two coats of weather proof antifungal exterior paint as per manufacturers instructions over a coat of true care exterior wall primer over two coats of external birla putty 1.5mm thick each layer each to level the surface and finished smooth with emery paper No.180 followed by emery paper No.320 or 400 and wipe it clean complete all as specified and as directed by Eng-in-charge. Make:- APEX ULTIMA of ASIAN PAINT/ WEATHER COAT SMOOTH(BERGER PAINTS)/ WEATHER SHIELD MAX EXTERIOR ACRYLIC(DULUX)

M&L for preparation of old plastered surface of wall and applying one coat of Acrylic exterior emulsion paint of approved make and shade complete all as specified

M&L for preparation of new plastered surfaces and applying two coats of weather proof antifungal exterior paint as per manufacturers instructions over a coat of true care exterior wall primer over two coats of external birla putty 1.5mm thick each layer to level the surface and finished smooth with emery paper No.180 followed by emery paper No.320 or 400 and wipe it clean complete all as specified and as directed . Make:- APEX ULTIMA of ASIAN PAINT/ WEATHER COAT SMOOTH(BERGER PAINTS)/ WEATHER SHIELD MAX EXTERIOR ACRYLIC(DULUX)

M & L preparing new plastered surfaces and applying three coats of white wash on ceiling

M & L preparing old plastered surfaces and applying two coats of white wash on ceiling

Demolition of old existing unserviceable WHB glazed and S&F vitreous china wash hand basin white of size 550 x 400mm flat back excluding taps, waste chain and plug but including brackets, CP waste fittings 32mm dia including cutting for and pinning in ends of brackets or erecting stand complete.

S & F in repairs Vitreous wash down water closet pan (Pedestal pattern), (ETWC) white including plastic water closet seat, white, closed pattern with flat bottom, cover and mild steel chromium plated or aluminium hinging device and fixing bolts complete all as specified and directed by Engr-in-Charge.

S & F in repairs Vitreous China Half stall urinal White complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets.

S&F in repair vitreous china sqquatting pan 'Orrissa pattern' size 580 x 440mm white , with integral foot rest, suitable CI trap including connection to trap, flushing pipe, antisyphonage pipe etc, including trap set in and including concrete and making good to floor complete all as specified and directed

S&F sink with drainage board made of stainless steel 1.0mm thick for kitchen with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or with 7 including fixing cantilever brackets and connecting union to pipe, overall size 1120mm x 457mm bowl size 460 x 330 x 203mm including waste pipe of polythelene of flow or high density or PVC 32mm dia & waste fitting brass chromium plated for 32mm bore with long screwed shanks and fly nuts including making holes in stone walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0 complete including taking down of existing old sink.

S&F in repair grating doom 125mm dia with waste hole of PTMT ( minimum weight 40 gms)

S&F in repairs 10 ltrs capacity, PVC valve less, syphonic action type, flusihing cistern, low level, white with inlet, ball valve, float and handle including brackets and suitable flush pipe PVC 32mm dia complete all as specified and directed.

Taking up or down steel tubing and connections, Supply and fixing 15mm dia GI steel tubes, medium grade with all fittings and fixed complete to wall and ceiling or laid in floors all as specified and directed.

Taking up or down steel tubing and connections, Supply and fixing 20mm dia GI steel tubes, medium grade with all fittings and fixed complete to wall and ceiling or laid in floors all as specified and directed.

S & F 1000 Ltrs capacity rotational moulded polyethylene water storage tanks three layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe etc complete all as specified in SSR Part I, including dismantling old water tanks Make - Sintex/ Polycon / Infra

S & F Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed bore dia of pipe 20mm

S & F as in repair stop valves cast copper alloy screwed down high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 20 mm bore fixed

S & F Waste coupling suitable for urinal and sink etc., of PTMT (Half or full threaded) of minimum weight 45 grams, and fixed to discharge pipe of 32 mm dia., bore.

S & F in repairs Brass Chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges.

S & F as in repair angle stop valves cast copper alloy, fancy type chromium plated, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 15 mm bore fixed

S&F in repair PVC connection 15mm dia 450mm long with 2 Nos brass check nuts with washer complete all as specified

S&F in repair PVC connection 15mm dia 600mm long with 2 Nos brass check nuts with washer complete all as specified

S & F in repair Bib taps, cast copper alloy chromium plated, fancy type with crtuch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule 15mm bore fixed

S & F as in repair fancy type pillar tap cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in stone, concrete block or slab wall.

S&F framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters walk ways, railing, frame work of water tanks and similar works conforming to Fe-290, Gde -E- 165

M & L preparing new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zink chrome primer

Dismantling of existing AC/PVC soil and waste and rain water pipe 100mm dia including fittings,viz, bends , tee from walls

Dismantling of existing AC/PVC soil and waste pipe 75mm dia including fittings,viz, bends , tee from walls

M & L for PVC (SWR) plain Floor trap of 75 mm dia., outlet with grating including jointing with solvent cement.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls.

S & F 110 mm bore PVC (SWR) Soil,rain water, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls.

S & F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door.

S & F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door.

S & F 110 mm bore PVC (SWR) Vent Cowl

S & F 75 mm bore PVC (SWR) bends of any radius.

S & F 110 mm bore PVC (SWR) bends of any radius.

Taking down chowkats or frame with shutters (without taking off shutters from frame) but each not exceeding 1.50 Sqm

Taking down Chowkats or frames with shutters exceeding 1.5 Sq. M but not exceeding 4 Sq. M each (Without taking off shutters from the frame)

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm from the frame steel/ wooden/ PVC complete all as specified and directed by Engr-in-Charge

S&F 35mm thick 2nd class hard wood rail and stype plain framed, panelled shutter ( two panel ) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both face. The size of rail and stile as per IS- 1003 (Part -I) , kiln seasoned and chemically pressure treated complete all as specified and directed by Engr-in-Charge

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube of 1.25 mm thickness suppling & fixing in opening as per specification & drawing

S&F factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified

S&F 150mm long aluminium anodised, barrel tower bolt of extruded section complete all as specified

S&F 150mm size extruded aluminium , alloy handles fabricated type, anodised complete all as specified

S&F aluminium alloy anodised sliding door bolts 300mm long with hasp and staple ( bolt type) & fixing clips of sheet or extruded section & fixing bolts & sliding bolts of extruded section

S&F in repair floor door stopper 150mm of aluminium alloy body and tongue anodised with hard drawn steel spring complete all as specified

M&L preparation of new or previous untreated surfaces of wooden surface of any description, not otherwise described, over 10cm width or girth applying two coat of synthetic enamel paint over a coat of pink primer all as specified

S&F venetian blinds ( vertical type) of 100mm wide straps with all fittings ( to be matched with existing patterns) & taking down old venetian blinds complete all as specified and directed.

M&L for PCC 1:2:4 type B1 ( using 20mm graded stone aggregate) in cills, steps, seismic and other damp proofing courses, plinth courses , water tank base, string courses, lacing courses, parapets and railing upto 60cm in height, coping etc complete all as specified and as directed.

M&L plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregates) as in plinth protections 75 mm thick finished even and fair with joints 10 mm wide and in full depth at corners and @ 3m c/c filled with mastic mortar

M & L for Cement concrete type D2, 1:4:8 (using 40 mm graded stone aggregate) in mass concrete of sub base of flooring/ hard standing.

Demolition of plain cement concrete in ground floor and paving n. exc 15 cm thickness ( below or above ground level ) complete all as specified

Material and labour for 30cmx30cmx23 to 25 mm thick rubber moulded chequered cement concrete tiles precast hydraulically pressed of approved colour and pattern as in pavements with grey cement and pigments over screed bed 15 mm thick in CM 1:6 complete all as specified

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m depth for foundation etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in hard/dense soil.

M&L for brick work with fly ash bricks sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in CM 1:6 complete .

M&L 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces and finished the surface fair and even without using extra cement complete .

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soils.

Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point.

S & F Mild steel work in hand rails, half round or other stock section or core for wooden hand rail straight portion, drilled and counter sunk for balusters, nosing to steps including embedding in concrete and screwing etc., wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shapes as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc., and similar work confirming to Fe 290 Gde E-165.

S&F MS screw bolts (Machine made) 11 to 15mm dia exceeding 5cm & n exc 10 cm long hexagonal or square head at one end and screwed other end to be fixed with one washer and one hexagonal nut, the other end to be embedded in RCC fencing post while casting, completed all as specified and directed.

S&F mild steel work in framed work as in doors or gate of square hollow pipe or other section and hunged as gate including pintle hinges, stops, hand made sliding bolt and similar work confirming to Fe-2902 Grade E-165 complete drilled or welding for fixing of steel sheeting square hollow section other covering and hanging or sliding with and including wheel and wheel track either hooks etc complete all as specified and directted

Supply only Chain link fencing 3.4mm dia galvanized wire (100x100) mm mesh made upto matress lapped wire and laid on position / fixed on poles complete.

Fixing only chain link fencing including line wires, any mesh , size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire.

S & F Galvanized, 2 strand, steel barbed wire 2.24 mm dia., barbed with 2 mm dia., barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanized mild steel pins etc., as directed.

M&L Preparation of new steel surfaces of any description, n. exc 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zink chrome primer all as specified and directed.

M&L for 100mm Plain Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing finishing cement concrete surface even and smooth without using extra cement

Taking down carefully of any type point wiring light / fans / socket or power complete fitting such as switch ceiling roses, pendent, regulator, sockets etc removing material and making good disturbed surface of wall floor etc complete all as directed.

M&L for wiring point wiring complete with 1.5 Sqmm PVC insulated unsheathed single core multi standard copper conductor 1100 V grade drawn through in and including 20 mm dia pvc conduit concealed on walls/fixing it with existing iron canopoy of shed with and including suitable size MS clamps etc. and Terminated to sunken box of modular type including white cover plates suitable for fixing switches, sockets etc including 1.5 Sqmm PVC insulated Copper conductor cable as earth continuity conductor and connecting to common earth dolly and taking down old one complete all as specified and directed for the following:-

One light point controlled by one way modular switch 6 Amps

One ceiling fan point /Exh fan point controlled by one 5 Amps one way switch and regulator

One 3 pin 5 Amps switch socket outlet point on independent board

One 3 pin socket outlet 5 Amps on the same board with other switches.

One bell point controled by one bell push switch

M&L for point wiring complete with 2.5 Sqmm PVC insulated unsheathed single core multi standard copper conductor 1100 V grade drawn through in and including 20mm dia PVC conduit concealed on walls/fixing it with existing iron canopoy of shed with and including suitable size MS clamps etc on Ceiling and Terminated to sunken box of modular type including white cover plates suitable for fixing switches, sockets etc including 2.5 Sqmm PVC insulated Copper conductor cable as earth continuity conductor and connecting to common earth dolly complete all as specified and directed for 3One 3 pin socket outlet. 15 amps,independent:- Make:- Conductor: Finolex/Finecab/Polycab/Plaza PVC Conduit: Finolex/Tirupati/Supreme/Prince/Avon plast/ Plaza

S&F modular switch one way 6 amps 1 module

S&F modular switch one way 16 amps 1 module

S&F modular fan step type regular two module

S&F modular socket out let 6 Amps 230 volts AC 3 pin multipurpose type complete all as directed.

S&F modular socket out let 6/16 Amps multipurpose complete all as directed by Engineer-in-Charge.

S&F ceiling rose two to three terminal surface backallite type AC 50Hz 230 volts complete

S& F Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings

S&F Buzzer, Ding Dong AC. 230 volts,single pole

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete

Taking down Ceiling fan/Exhaust fan of any make and sweep dismantling, cleaning greasing/ overhauling, adjustment of down rod including replacement of rubber , bolt & nuts etc including new painting in two coats with existing colour and refixing in existing position with new cable wire connection between ceiling rose to fan connector complete all as directed by Engr-in-charge.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20Amps complete

S&F Triple pole and earth encolsure with a three pin and earth plug with socket complete with one triple pole MCB, 415V of 63 Amps capacity complete

S&F MCB single pole 5 Amp to 32 Amps complete all as directed by Engr-in-charge

S&F MCB SPN 240 Volts 40 Amps complete

S&F MCB TPN 415 Volts 40to 100 Amps complete

S&F sheet metal enclosure MCB DB TPN double door type AC 415V 4 way with 200 Amps rated bus bar, including taking down old one complete and making good of distrubed surfaces.

S&F sheet metal enclosure MCB DB SPN double door type AC 240 V 12 way with 200 Amps rated bus bar, including taking down old one complete and making good of distructed surface including taking down old one complete

M&L for sub main wiring complete with 4 runs of 10.0 Sqmm PVC insulated heavy duty and unsheathed cable with multistranded copper conductor and drawing through in and including PVC conduit concealed on walls/fixing it with existing iron canopoy of shed with and including suitable size MS clamps etc and connecting terminal ends to meters and DB's including provision of 1 run of 10.0 Sqmm insulated copper cable for earth continuity conductor and connecting to earth dolly including taking down old u/s one complete

M&L for sub main wiring complete with 2 runs of 04 Sqmm PVC insulated heavy duty and unsheathed cable with multistranded copper conductor and drawing through in and including PVC conduit concealed on walls/fixing it with existing iron canopoy of shed with and including suitable size MS clamps etc and connecting terminal ends to meters and DB's including provision of 1 run of 04 Sqmm insulated copper cable for earth continuity conductor including connecting to earth dolly and taking down old u/s one complete

M&L for sub main wiring complete with 2 runs of 2.5 Sqmm PVC insulated heavy duty and unsheathed cable with multistranded copper conductor and drawing through in and including PVC conduit concealed on walls/fixing it with existing iron canopoy of shed with and including suitable size MS clamps etc and connecting terminal ends to meters and DB's including provision of 1 run of 2.5 Sqmm insulated copper cable for earth continuity conductor and connecting to earth dolly including taking down old u/s one complete

Earthing complete with GI earth plate electrode 600x600x6mm buried directly in ground vertically to a depth of not less than 2.25mtr below ground level connected to GI wire 4.0 dia by means of bolts washers etc made out of strip wire will be protected by galvanized iron pipe medium grade 15mm bore up to main distribution board/main switch including necessary excavation and earth work PCC 1:3:6 type CI (using 20mm graded stone aggregate) RCC cover 1:2:4 type B1 including necessary reinforcement etc complete all as shown electric plate No.3 of MES Sch Part-I.,

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 2mm dia galvanised iron or steel wire of size 4.0mm dia complete

M&L for Rigid non-metallic PVC conduit exclusive of boxes (junction/terminal) but inclusive of all tees, bends,elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. for telephone line

Taking down existing sign board DMRL gate writtern in three laguages complete with all fitting and fixtures complete ( Hindi, English and telugu) all as directed

Supplying and fixing iron and opaque acrylic 3D Dual channel letters of size 30", 3mm thickness and 100mm debt and 125mm width with 0.40 transparency high tech plastic material particularly high transparency and impact resistance levels. Providing iron sheet of 1.5mm thick for the base of 3D channel letters with hydraulic machine bending the channel letter shape along with zinc premier emulsion painting for anti rusting. Providing artwork designing for displaying the 3D View of DMRL in Three Languages hindi, English and Telugu. Providing customized Laser cutting to the art work design of 3D channel letters on opaque acrylic sheet. Providing soldering process fabrication to the laser cut acrylic sheet creates the back of the channel letter the sides of the channel letter are formed by bending a 4 inch wide (100 mm) strip of fiber sheet around the 3D channel letter. Providing opaque acrylic 3D walling of 2” inches debt with soldering, grinding. Providing AutoCAD artwork drawing layout sketch for assembling and installation of the 3D channel letters with digital laser light level alignment with hammer drilling araldite adhesive, anchor fastener bolts as per the artwork drawing. Suitable care to be taken to ensure concealing the cables and fixing of 3D letters without any disturbance to the back drop fascia wall. Providing standard fastening and hardware components complete in line and levels duly sealing the holes with silicon sealant. All anchorage and fastening of miscellanies metal items shall be structurally adequate and finish to match surface. roviding SAMSUNG 2mm LED Modules light intensity and distribution in according to particular light to dark ratio 1:3 nominal current 6.6 A operating voltage range from 21 V to 25 V power consumption 20 W/m (approximately), efficiency 95% insulation resistance 50 MΩ insulation voltage 1000v (1 minute 50Hz) fuse integrated (DIN 72581) cable gland 2x2 type skin top M20x1,5x16 life expectancy 20,000 burning hours (Five Years Warranty) with laser emitting diodes 20mA to 120mA constant current a high voltage supply with a very high internal impedance for high brightness applications for 3D channel letters with crystal structure lighting back up structural surface mounting to the backside of the 3D channel letters. Providing power suppliers to the LED Modules Light for power supply to the 3D channel letters with input 220v and output AC / 3-15 V DC. with internal three core cable of havells brand wiring with casing to the internal cable wiring along with installation and commissioning LED corporate signage. All curved areas are free from kinks anchor fastener bolts and fastening devices are non corrosive materials and with all required infrastructure and hardware items etc., complete all as specified and directed

Supplying and fixing of 3D ILLUMINATED LOGOS of size 48"x 48" = 02 Nos Logos. Providing M.S. Box structure of 38mm x 38mm M.S. square pipe of 4mm thickness with M.S. “L” angle of 50mm x 50mm for support of MS Box structure with fabrication, welding, grinding, Zinc premier emulsion painting and with aluminum frame with suitable steel sections such as stanchions, angles flats along with self expanding cap and screws hold fasts. Providing white colour ACP sheet alloy 500 resins for anti fungal and anti bacterial properties with 3mm thick covered on front back and both sides. All curved areas are free from kinks anchor fastener bolts and fastening devices are non corrosive materials etc., complete all as specified and directed. b) Providing CNC router hollow cutting to the existing artwork design content of the corporate sign board for the lettering. Providing white opaque acrylic sheet of 10mm thick with computerized laser cutting lettering with 3M sticker as per the colour scheme along with vinyl print pasting on background Logos pasted on hollow cut lettering projecting 10mm from the hollow cut white colour ACP backdrop. Providing 6mm thick opaque acrylic sheet of 0.40 transparency high tech plastic material particularly high transparency and impact resistance levels mounted backside of the ACP sheet to cover the hollows of the text met with CNC router cutting. All curved areas are free from kinks anchor fastener bolts and fastening devices are non corrosive materials etc., complete all as specified and directed.c) Providing SAMSUNG brand 2mm with 3 watt water proof LED Modules light intensity and distribution in according to particular light to dark ratio 1:3 nominal current 6.6 A operating voltage range from 21 V to 25 V power consumption 20 W/m (approximately), efficiency 95% insulation resistance 50 MΩ insulation voltage 1000v (1 minute 50Hz) fuse integrated (DIN 72581) cable gland 2x2 type skin top M20x1,5x16 life expectancy 20,000 burning hours (Five Years Warranty) with laser emitting diodes 20mA to 120mA constant current a high voltage supply with a very high internal impedance for high brightness applications for 3D corporate sign board with crystal structure lighting back up structural surface mounting to the backside of the 3D channel letters. Providing power suppliers to the LED Modules Light for power supply to the 3D channel letters with input 220v and output AC / 3-15 V DC with internal three core cable of havells brand wiring with casing to the internal cable wiring along with installation and commissioning LED corporate signage etc., complete all as specified and directed.

Supply & fixing of ACP Board Box Structure for 3D ILLUMINATED Channel for Letters of size 25'x3' and for LOGO of size 5'x5'. Providing M.S. Box structure frame of 38mm x 38mm M.S. square pipe of 18 gauge thickness with M.S. “L” angle of 50mm x 50mm for support of MS Box structure with fabrication, welding, grinding. Providing Zinc premier anti rusting emulsion colour to the MS box structure. Providing Aluminum Composite Panel sheet of 4mm thick with alloy grade 3105 H 14 PVDF coating and protective film for anti fungal and anti bacterial properties surface protection. Compounded with top and bottom layers of aluminum sheet alongside non-toxic polyethylene core material. The macromolecular lamination protects the top and bottom layers of aluminum coil bonded to the inner polyethylene core. Cladding and Growing to the existing M.S. box structure with standard fastening and hardware components complete in line and levels duly sealing the joints with silicon sealant. All curved areas are free from kinks anchor fastener bolts and fastening devices are non corrosive materials etc., complete all as specified

Supply & Fixing MS self standing supporting structure to the ACP Board having for letters board of size 25'x3' and for logos board of size 5'x5' logos with MS“L” angels poles of 75mm x 75mm x 6mm and with MS base structure supporting for self standing of the ACP Board of 300mm x 300mm x 6mm “L” angles along with 38mm x 38mm M.S. square pipe of 18 gauge thickness. Providing fabrication, welding, grinding, providing two coats of zinc premier anti rusting emulsion colour painting and providing red oxide to the MS Self standing structure. Providing concrete base of pit size 3'x2'x3'x4 and providing cement concrete 1:2:4 proportions. All curved areas are free from kinks anchor fastener bolts and fastening devices are non corrosive materials and with all required infrastructure and equipments along with incidental and operational charges etc., complete for finished item of work

Supply and installation of LED glow sign board with height 4ft and width 8ft for letters PROHIBITED AREA in three languages ( Telugu, Hindi & English) made of 1"x 2" MS pipe single frame fixed with ACP background, on it acrylic male & female letters, inside LED modules with rain proof power supply with required MS pipes on wall, fixing it by welding/brezing/plastering on secured, electrical connections complete all as specified and directed.

Supply install an testing of the high intensity, Energy saving, long range, multi functional, auto swivel LED search light beam range 700 meters, 1x300 W in multi curcuit LED light efficiency 100lm/w, PF >0.95, CCT 5500K-6000k, optical grade PMMA-PC lens, anti-UV oxidation, narrow beam 8 degree, die cast LM6 body with air fins,fully powder coated,working voltage 100-300 50Hz constant current, reflector/lens efficiency> 90% avarage lux level at 10 meter- 6000(min) with circle of approx 500mtr,IP-66 conforming to LM 79, Lm80, IS: 10322/BIS. this search should be installed on disc of revolving mechanism with suitable motor gear unit and design such to rotate 360 degree continously over the night in horizononal plane with speed controller (1 to 10 rpm) and r/F buttons and inbuilt push to tilting option upto 45 degree. A sperate wall mounted wire control panel (Consist of MCB's,V-meter, Fuse, LED indicators) is supplied for smooth and safe operation remotely, the revolving mechanism is fully covered with weather & rust proof fiber box with maintenance window/door and provision of 4 nos foundation holes at botom for proper installation complete all as specified and directed. Make Kalin. Cat no MRSL- LRFLL-25PC30, or equivalent model of make of SIGMA/Aaka/ point Blank (as approved).

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp/32Amps MCB complete all as specified.

S Anjan Reddy

rahi consultant

M/S jvsr constructions